Valley Installation - 1st Coast Metal Roofing Supply

Valley Installation
Subscribe to our page for more metal roofing videos!
Here at 1st Coast Metal Roofing Supply, we value our customer service and product quality above all else. That's why we are building business relationships with loyal customers as we expand. We hope our videos have been helpful to you!
Please contact us by phone or email during business hours if you have questions we can help with. Also, getting a quote over the phone of your metal roofing package is made very simple here at 1st Coast Metals. You can find us on most of your social media platforms and we look forward to hearing from you!
Phone: [phone]
Email: [e-mail]

[@b-radumuck7903]

My 30 year asphalt roof I installed and know all the flaws .. never failed on the flaws but the shingles shrank dont past the nail line in 20 years.. a contractor wanted 34grand to do what me and my friends did in 3 days .. 20 years ago lol.. we replaced every piece of plywood . That job didn't last 20 years.. last year I replaced a metal roof that had only minor leaks arround chimney in Florida weather that roof was over 80 years old .. I was proud to replace that roof with metal .. I'm not going to live till I'm eighty but I can try and watch this new roof age .. I know it will last more than 20.. and if it dont it's easy to replace and a tenth of the cost if that .. and hug this a little while.. its recyclable down to the screws

[@b-radumuck7903]

Thank god for metal roofing ... lol and vidio tutorials too🙂🙃🙂

[@MrJrh458]

I've found all these videos show how to do the simple job of doing the valley but none of them show how to cap off the valley peak. I assume they just use a lot of silicone and the valley peaks are good for a few years and start leaking

[@b-radumuck7903]

I watched a lot of videos painfully I might add.. some tell you a little bit but you might need to experiment a while.. in one vidio the older mexican guy capped that vally with little over lap and hammered the vally center together.. so you can torment your self or just do the best you can.. just saw a roof with piece of rubber over the vally peeks and said well why not didn't look to bad and solved his worries.. invention is allways driven somehow in this way..

[@TicoTimeCR]

i agree with people saying this will leak. The screws need to be above (or perhaps in) the foam tape. Otherwise, they will create holes in the valley flashing below the foam tape that are not protected. The screw washer only protects the top panel

[@b-radumuck7903]

I'm beginning to realize that really the seal is to keep wind blown rained snow from topping the vally walls. As long as your valleys dont dam up with debree gravity is on your side water shoots down these valleys like its rocked propelled so unlike asphalt roofing where the water soaks in and slowly seeps it's way down you dont have a back flow problem .. but if you do the seal is for that.. go up and look up that vally when its pouring rain .. you'll maybe get a new prospective of how metal roof sheds water like duck

[@dewaynehutcheson9921]

Huge leak at the top of this valley.

[@lucycats6282]

So where’s your video? You know, the correct way to do it?

[@juancristobal7692]

I love your video thank you for putting this type videos up

[@1stCoastMetalRoofingSupply]

Glad you like them!

[@danieltaylor1181]

says to use panhead screws, but shows the use of flathead, countersink screws.

[@TheAdkFlyer10]

Yup, same system on my house and every time it rains hard, it leaks.

[@kalbestbareh1312]

Thanks for a good video

[@lancekuykendall3017]

You never should put screws that close to the bottom of the panels. As a rule of thumb, no screws should touch the valley pan

[@primalfury2011]

WHAT HOLDS IT IN PLACE THEN ?

[@markoshun]

This does not show how to fully install the valleys. There is no detail re: the top.. where leaks are most likely.

[@rob2950]

These are the best people over there at 1st Coast Metal Roof supply !!!

[@littlebigman2947]

I'm working on a metal roof and it sucks to put on .I highly recommend asfault roofing over metal there terrible to install and putting the screws down is a nightmare.

[@davebrakefield161]

That's because you don't know what your doing. We put a 15 sq metal roof on in 2 1/2 hrs after prepping the roof after tear off.

[@dukeman7595]

Well made video, simple and to the point.

[@1stCoastMetalRoofingSupply]

Thank you!

[@azurazdandaridae9158]

Didn't show what to do with the cap of the two. Thumbs down.

[@debrahjohns586]

What is price of metal

[@alfredogonzalez-sc9hj]

Thi is a very helpfull video

[@jeanluctrader]

This roof will leak

[@user-pj9oz6oy9v]

Si pero el maderaje que tiene cruzado por dentro eh los grande eso es los que no se como van ha entrale ha eso

[@youssefbeleattar252]

This is amateur work. No close at the bottom of the valley to prevent insects and actually look professional and clean, and the top is a guaranteed leak.