Fix Drill - PARKSIDE Performance "PSBSAP 20-Li A1" Gearbox Fail and Repair (Not Locking the Shaft)

Поділитися
Вставка
  • Опубліковано 22 гру 2024

КОМЕНТАРІ • 41

  • @DjaniAgain
    @DjaniAgain 3 роки тому +3

    But how these little shafts came out at first place 🤔
    Nice repair! They had to make you an official service 😁

  • @markifi
    @markifi 8 місяців тому +1

    what are the function of the 6 tiny cylindrical parts? 3:35

  • @emilvlahovic3917
    @emilvlahovic3917 3 роки тому +2

    Sounds much smoother with more grease, they sound quite dry stock...

  • @orlatris96
    @orlatris96 2 роки тому +1

    Congratulations, another great video, thanks for sharing. I have a screwdriver just like this one that sometimes, without anyone touching it, starts working by itself. Do you have an idea as to what could cause this? a hug, thank you very much

    • @ErCanEverything
      @ErCanEverything  2 роки тому +2

      Thank you very much🙏🙂🤝
      This can be caused by moisture, a faulty button or controller?🤔

    • @orlatris96
      @orlatris96 2 роки тому +1

      @@ErCanEverything thanks

    • @良くん-c5t
      @良くん-c5t 11 місяців тому

      😅😂😂😂😂🎉😢😢😢😢😮

  • @deanzimmermann6690
    @deanzimmermann6690 4 місяці тому

    Any idea where I can get a drill chuck for Model PSBSAP 20-Li C2?

  • @ZONAALATA
    @ZONAALATA 3 роки тому +2

    Nice and useful video :)

  • @barbossajacksparrow9481
    @barbossajacksparrow9481 Рік тому

    Nice job!!!

  • @makeandfixathome
    @makeandfixathome 3 роки тому +1

    well done mate

  • @TeoPriceputul
    @TeoPriceputul 3 роки тому +1

    Nice vide. I dont have this one yet. ✌️👍🤝

  • @ronmann7395
    @ronmann7395 2 роки тому +1

    Good job

  • @reselty
    @reselty 4 місяці тому

    Hello ErCan
    You seem to have looked into the device in great detail!
    I'm a huge fan of the device - it looks appropriately used.
    The fact that it keeps going on and on more and more often, especially with sensitive materials, has been really annoying for some time now.
    Of course I suspected the switch - but I'm not sure because it's so inconsistent.
    Have you or anyone else had similar experiences and worked out solutions?
    Does anyone know if the switch is available / standard?
    I assumed that many of the parts installed are standard and can also be obtained elsewhere, especially a switch with the manufacturer's name printed on it.
    Do you think I don't even have to take it apart to check this?
    Otherwise, I'd be happy if anyone who wants to kit out a ruin would contact me and offer it
    Thanks for the information everyone!

  • @otomobilimci
    @otomobilimci Рік тому

    I saw your video, I got the courage and decided to clean it, I have the same thing, I cleaned it, but the engine makes a ticking sound, it doesn't turn, what could be the reason?

  • @bobbys2160
    @bobbys2160 Рік тому +1

    anybody know a video that shows WHY a drill clutch keeps slipping? when in the drill mode

  • @to220
    @to220 3 роки тому +1

    Good job.👍 It's waiting for me too. My drill has the same error, spins when loosening tools.

    • @ErCanEverything
      @ErCanEverything  3 роки тому

      Thanks. I was a little worried about the disassembly, but it's not a difficult job. And easy to reassemble🙂

    • @jozefhudak822
      @jozefhudak822 3 роки тому

      Ahoj vidim, že si rovnako uleteny pre značku parshite ako ja. I hold my thumbs up for your work. Looking forward for more vids from ya.

    • @ErCanEverything
      @ErCanEverything  3 роки тому

      @@jozefhudak822 Vďaka kamarát, čoskoro nahrám nové video o nabíjačke do Parkside🙂

  • @bomby5345
    @bomby5345 Рік тому +1

    There was a small rectangular magnet that fell out of my drill when I opened it about 1cm wide 0.5cm high and 2mm thick.
    Does anybody know where it might’ve come from?

    • @ErCanEverything
      @ErCanEverything  Рік тому +2

      And my magnet fell off while opening it, I thought a lot about where it could come from and finally figured out that its place is at the back down where the battery goes to hold the bits🤦🙂

  • @YouGrafTube
    @YouGrafTube 2 роки тому +1

    Так-же была похожая проблема. Разобрал машину внутри все впорядке. Собрал, ничего не изменилось. Но потом обнаружил, что не до конца включался режим 1 скорости. Внутри заедает кольцо, на которое воздействует переключатель скоростей. Потом научился включать 1 скорость и проблема исчезла

    • @ErCanEverything
      @ErCanEverything  2 роки тому

      Sometimes does not engage at 1 speed.
      It needs a little load, and turns on immediately without a problem.

  • @HouseMastersTools
    @HouseMastersTools 3 роки тому +1

    Omg ⚙️🔧🛠

  • @mihail2618
    @mihail2618 3 роки тому

    What type of grease are applying?

  • @AutodidactEngineer
    @AutodidactEngineer 2 роки тому +1

    What made the gearbox fail?

    • @ErCanEverything
      @ErCanEverything  2 роки тому +2

      I installed a large and heavy mixer tip and it causes such a problem during a sudden stop when spinning fast.

  • @kiky2h
    @kiky2h 2 роки тому

    Hello, how can replace the Chuck, thanks a lot

    • @ErCanEverything
      @ErCanEverything  2 роки тому

      I haven't replaced but as far as I know you have to first unscrew the bolt inside the chuck with a screwdriver and then the chuck itself is unscrewed counter clockwise🙂

  • @dan_6915
    @dan_6915 3 роки тому +1

    I might have same issue

    • @ErCanEverything
      @ErCanEverything  3 роки тому +1

      Very easy to repair

    • @dan_6915
      @dan_6915 3 роки тому

      @@ErCanEverything
      lol.
      I have never opened one.
      But i've repaired a gasoline chainsaw ! :))
      I might get to the end of this drill also.
      ✌️

  • @Rafa-xl4uf
    @Rafa-xl4uf Рік тому +1

    Too much grease.

  • @ohnemar4285
    @ohnemar4285 Рік тому

    Terrible background music...