My 2001 Sierra 1500 was doing this. I followed your steps and it worked perfectly. If you are looking for something to put next to the plug to keep it from wiggling and coming loose again I used the sharp end of a zip tie. It was small, it gets progressively thicker and it's easy to cut. Thanks again. No more annoying Security light.
Very helpful, thank you. My wife's 2001 Monte Carlo had this problem, so I removed the ignition switch and checked that connector, which was found to be a bit loose. I didn't see any way to remove the wiring pins, but I did notice that a cable tie had been placed around the ignition housing, apparently to hold the connector in place and it had slipped out of position. Probably done by the dealer when they did the GM ignition switch recall repair. I cut that tie off and replaced it, then wrapped electrical tape around the housing to hold it in place. So far the car starts fine and the SECURITY message hasn't been seen again.
Tried it on my 2001 Suburban just now n it worked!!!!...thank you!!!...i was stranded at my aunts job n handily had a bobbypin to loosen the wires from the clip...plugged it back in and waited then it started...u r a genius!!!!...thought i would have to pay a tow truck and a shop to get it fixed...
@@Houston0068 srry so late...i broke my turn signal switch...n the guy that tried to fix it messed up wires n the module when he was taking the old one off to replace it...new part wasnt the right one...so when he put the old part back on it wouldnt turn over and the security light was stuck on even when the truck was off...had another guy replace the old switch and it wrkd for a while then the security light would flash quickly abt three times before going to the next alert and wouldnt turn over...tried this n it wrkd...no issues since...
Thanks for this. I think this fixed my no start problem on my 02 Duramax. I been fighting this for years. 2 different cars. I even took it to Chevrolet once they just threw parts at it. I learned to live with it. Just had to wait 15 minutes every now and then. I think this should have been a recall. Thousands of people have this problem.
Did your truck start and turn off immediately? I have had that problem since Inpurchaed the truck and have jot fixed the issue, but now that my boy is going to start driving it I dont want him starnded someplace because it wont start since he will ise it for school.
I've watched countless videos on this topic, none were as easy as this. It took me 20 minutes to fix my problem and just like that my truck started Thanks for this video posting
Results! 2003 suburban,so I checked the switch made it more tighter,but my problem was a ground going to the PCM,they are two ground wires behind the block on top and one of them was completely broken.all fix.😁👍🍻
@@ramiresamador2383 Theirs 2 braided wires behind the engine block, like on the corners. Buy the ground wires a napa auto parts. Google ground wires location.
If you are watching this lookin for answers, this is it. Mines been doin this on and off for a while and finally it just wouldn’t start. Some research led me to this vid. I can’t say thanks enough for this. Fuck n a.
Just bought a 2001 tahoe the other day and it has a few wires hanging out amd cut. Everything is working loke it should but it looks like i better take the plastic off to see of they bypassed it somehow and double check everything. Thanks for the upload.
I figured i would try it because ive tried everything else. Holy crap it worked dude! Thankyou for posting this vid. My 2001 suburban k2500 runs again!
5 years later, still driving, no blinking, still good. I would love to know how you're making your gas last sooo long. My 25 gallon tank needs filling every week.
Well if that doesn't work then it's your tbc fuse which is located in the fuse box in the engine.. it's a 10amp by the way.. it should get rid of that security light and if your headlights don't work or interior lights then it more then likely is that tbc fuse... Truck:2000 gmc sierra 1500 5.3
My 2000 Oldsmobile Silhouette minivan message center does the same thing as yours: Battery light, low fuel, and security. What other symptoms did you have? Did the engine crank or start? Mine will not start or crank at all.....
I recently bought a 2002 chevy tahoe. Runs good, drives nice, no dents on the body. For myself it only has one problem. Every time unlock the door and open it the security light will come on and horn will start honking until you put the key in and start the engine. It has no problem starting the engine and does not happen if opening an unlocked door. Only if door is locked. Any solutions on how to fix this is greatly appreciated. Thank you.
was your light on when the truck was off? my lights on sold 24 7 no flashing. i can start the truck drive it just fine but it slowly drains the battery and if i dont drive it daily it kills it then have to replace it from constantly dying. i am going to try this after work regradless just trying to pin point it before hand if i can.
did you ever get yours figured out? mine does the same thing. if I don't start the truck for a couple days it won't start. but I can jump it every time
Question, you stated that the truck had to sit for 20 mins to get the light to go off. Is that with the ignition switch on or off? When turned on the message center strolls through. When powered off the security light stays solid and never goes out.
For everyone else out there wondering what’s going on after your ECM swap, for a 1999 - 2000 Silverado, you can swap an ECM from a similar enough vehicle. Generally it will run, sometimes it won’t. Where I’m at, if it doesn’t run after the swap then my dealer can re-flash it for $90. I will post about this in my channel when my engine swap is done
@@TheCuban.45 I completed my swap. The ECM from 2000 Sierra 5.3l did not allow my 1999 Silverado 5.3l to run, but my stock 1999 Silverado 4.8l ECM did allow the engine to run. I believe this is due to the VIN on the ECM not matching the VIN in the BCM (BCM is located in the dash near the steering wheel). I made a video to document the results: ua-cam.com/video/8Uya_inXYl0/v-deo.html
What was the main issue just the light? my 2002 alarm system just goes off for nothing at any given time when using the remote key lock. rouge security system works random. leave it unlocked no problem, only when locked?
Very good on getting that light out, annoying wasn't it? quick ?, When you shut off the truck Take the key out and open the Door does your security light start flashing till you shut the door? Or is that something else? I have a 2000 Chevy Silverado.
i have similar issue does this security light some kind of safety mechanism to keep from starting in the case of stolen vehicle? everything is brand new and sounds perfect it could be the only other reason it wont start
I have a 2000 Chevy Silverado , while on the high way , all lights cut out , expect turn signals and break lights truck did not die till next morning , now it won’t start if not driven for hours , security light turns on I’m able to jump It but no lights turn on low and high beams , no interior lights either any help ?
I’m a little dense, sorry. When I have the issue of my 2002 Tahoe not starting sure you saying a loose connection is the problem? Some of these videos say the vehicle will start for 3 seconds then die, my problem is I turn the key and I get nothing, no start no click or anything. Will this work for me?
I have the same problem with my 2002 chevy 1500. Even the low fuel indication issue, but also the temp gauge not working either. I tried this trick, but no cigar. I guess it could be the ignition switch, will try that next. I tried the instrument cluster in another truck and it works fine. Right now, the instrument cluster is removed since it drains the battery overnight.
Question I'm having an issue like this but only with the door open and I was wondering if it might interfere with the reason I have no power to my fuel pump for it to start will this reset the security so that everything will work again
What do they call that housing that you put the three wires in. And what is the housing going into what's the name of that piece?? And where can it be found???
My 01 Silverado has a sporadic issue of not starting: turn key and hear less than a second of fire, then shuts down automatically. I’ll be stranded for a while. I did this crimp and the same issue returned. Maybe it’s the housing like he suggested.
Timothy Weinert I don’t have the security light on when it starts either. The problem may be the housing because of the magnetic signal within that helps generate the proper voltage.
Gonna try this on my 99 Silverado cause I am having that same issue. Truck starts up, but the Security light stays solid even when off. I am going to try this tomorrow.
The Cuban .45 what's up ? If that wire is loose will it keep truck from starting even stop it from starting spraying starting fluid into throttle body? Truck just quit while driving . my window was down and it rained like hell inside of truck causing door to keep locking and unlocking the next day . then the alarm would turn on randomly during the following day
Did you also happen to have your abs fuse for your brakes pulled as well? I was getting a low speed wobble when braking and had to take my abs fuse out, otherwise I wasn't able to stop cause the abs system would kick in. That was a year ago and now my security light is on and ran down a brand new battery. Do you think this is my problem?
@@TheCuban.45 OK, anyways, I am very thankful for your video because it gives me something else to look at. I needed a new battery anyways, the old walmart battery lasted me 7 years, so I couldn't believe that either. I will check to see if I have the same problem as you. I hope so cause it looks like an easy and cheap fix. BTW, if you ever have trouble with your brakes when you are driving slow and the brakes start acting funny, then all you have to do is pull that abs fuse and it solves your problem. At least until you find out why you are getting a low speed wobble. Which more than likely means you need to install a new hub. Thanks again!!!
My 2002 chevy wont start up ,im thinking maybe its this since security alwayd flashing aswell. Turns off on me whenever i break , or just wont start at all
I have a 2007 GMC Yukon with the security light showing I tried just about everything dislike this looks like it could be the problem. Just let me know what the name of that piece in the ignition is called
I know this has been up awhile but i have a 2001 GMC Yukon. It is doing the same thing. The first time it did thisdisconnecting the battery stopped it. Now its doing it again and disconnecting the battery didnt work. My mechanic in town said take it to the dealer. Im a disabled senior citizen . is this something i could do? If so how do you take the cover off?
is the security light supposed to be flashing while the truck is off? i never had an issue with it not starting cus of it, im not 100% sure if it stays on while im driving, my check engine light stays on so i tend to overlook my indicator lights by default.. something lately has been draining my battery and im trying to figure out if that little security light can be a drain. Didnt isolate any issues through a parasitic draw test, so all i have left is glove box light, hood lamp, and this security light
@@TheCuban.45 i havent gotten my battery back in yet to verify if it flashes while the truck is off or just when i open the door. i dont have a fob so i use the key to unlock, and power locks to lock unless one of them is sticking too hard for the motor, idk if any of that makes a difference. But the truck always starts, ive never had it not start cus of it. all i know for sure is when i open the door i see it flashing when i get in, i need to verify if its on before i open the door and if its on while im driving i guess. Trying to find answers but seems my issue is just slightly different than what most these videos are about
What if you got a viper alarm installed on it and the security light is on when the truck is on and won’t go away expect for when the truck is off any suggestions ?? 🤔🤔
@@TheCuban.45 ok I tried the relearn process about 100 times but didn't work I also tried connecting the yellow and Orange wire together and tried the relearn and still nothing.
Check the negative ground cable that goes from your battery to the red junction box. Then follow the negative from there to a bolt on your engine block. Clean it and tighten it. It makes the truck act crazy when it's loose or dirty with engine grime and oil residue. It took me one steering column, key cylinder, fuel pump, fuel filter, fuel injector pressure regulator and a whole lot of reading until I found a video on yt with this info.
Thanks for making this video. I am having the same issue with my 2001 GMC Sierra 2500HD. I am going to tighten my passlock connector as you have shown. I do have one question. What did you use as a pin at 4:58 to wedge the connector?
My 2002 gmc yukon did the same thing I turned it on and the battery light was blinking the security light was blinking low fuel light was blinking, my doors wouldn't lock on there own like the normally do when you pull it into drive my gas gage temp gage wouldn't work either! And when I would pull it into drive it wouldn't light up on what gear I was in.
it would have been better if you try start it before and after,cause the sound of the truck that it start helps alot, cause my sound like it want to start!
I have a similar problem with my 2002 Chevy Silverado, after replacing the fuel pump, spark plugs, gas filters etc it still wouldn't start... so at this point ill try anything.. I'll give it a shot tomorrow and give feedback. Wish me luck.
The Cuban .45 thank you. Mine does krank and after 2 sec shuts off .still cant figure it what it is .replaced fuel pump, spark plugs unplugged cam sensor so i don think is it
My 99 is doing this ATM but we aren't trying to fix it ATM we are trying to fix the trans and t case adapter that broke due to a u joint blowing out the drive shaft
My husband just replaced the starter. The battery was disconnected. Now it doesn’t start. The battery light and the light that says security is flashing & that is it. My deck turns on but my gauges and everything else doesn’t move. No crank no noise nothing! Hoping this could be it!?
My problem is that I’m having to take the negative wire off the battery ,take a pair of jumper cables connect to the positive and to the negative and wait 15 or 20 minutes to reset the security system because the truck will not stay running ,I need to do away with the security altogether ,how do I do that?
Trying this when I get home tomorrow! My 02 Tahoe was parked for 2yr and I jumped it off. It crunk up fine for 2weeks straight and after I replaced the battery it never started again. Security light is on. I will let you know the results
Nice video very good direct information, the only thing I could find as a complaint is all the wiggling and the bad focus but Hey that's what it takes to get it done bro, thank you!!
GOOD old GM ; They build a critical over riding system and use hairlike wires and crappy connecting posts IN A MOVING environment :: EVERY time I work on GM I swear I want to line up their pinhead engineers and commit a felony ! WHAT, were they thinking ? I have switched to Honda and KIA- AMaaaazing engineering on a KIA !
@@funseeker1969 i had the tbc fuse problem last year yellow security would stay on constant even key off and out no headlights or interior lights truck would run though fastforward a year same symptoms but the fuse is good and now its progressed to a start run 2-3 seconds die just like a pass lock probem but i cant do a relearn as the ligth goes solid any ideas
i had the tbc fuse problem last year yellow security would stay on constant even key off and out no headlights or interior lights truck would run though fastforward a year same symptoms but the fuse is good and now its progressed to a start run 2-3 seconds die just like a pass lock probem but i cant do a relearn as the ligth goes solid any ideas ps the fuse box has been changed
One thing I noticed was the fuses in fuse box started corroding would test ok with a simple test light but measuring the voltage across them was erratic. Decided to pull every fuse and found 5 to 10 of them corroded even a few that tested ok but once pulling them out broke because of it so I took ever fuse out and cleaned every terminal used die electrical grease and installed almost half with new fuses and all issues went away later on I replaced the whole fuse panel because for some reason they corroded on the bottom and internally (once I took the old panel apart to see it was green cancer everywhere) plus another huge things with these trucks is grounds specially the one by the cab mount under the drivers door hope this helps in any way
My truck is 2000 chevy 2500 6.0 an its doing that with lose of power to sometimes it will run just fine an no eng lites at all on an it will lose power
Hi there! What happen did you fix your issue? I just switch my Computer too...I'm trying to by pass the security sistem and Nothing! My car doesn't start...
Envwee I have not put my engine back in yet. I think I’ll end up just using the same one and having it reprogrammed to run like a 5.3l. Though, out of curiosity I may drop the 5.3l ECM in there to see what it does. The dealership claims it should run no problem. For issues like that you should reach out to your local Chevy dealer and ask someone in parts. They’ll be able to tell you right away
over 2 months as of 2/7/22 since I did this FIX and has not let me sit again! I am impressed! THANK YOU!
My 2001 Sierra 1500 was doing this. I followed your steps and it worked perfectly. If you are looking for something to put next to the plug to keep it from wiggling and coming loose again I used the sharp end of a zip tie. It was small, it gets progressively thicker and it's easy to cut. Thanks again. No more annoying Security light.
I'm glad it worked out for you
Very helpful, thank you. My wife's 2001 Monte Carlo had this problem, so I removed the ignition switch and checked that connector, which was found to be a bit loose. I didn't see any way to remove the wiring pins, but I did notice that a cable tie had been placed around the ignition housing, apparently to hold the connector in place and it had slipped out of position. Probably done by the dealer when they did the GM ignition switch recall repair. I cut that tie off and replaced it, then wrapped electrical tape around the housing to hold it in place. So far the car starts fine and the SECURITY message hasn't been seen again.
Tried it on my 2001 Suburban just now n it worked!!!!...thank you!!!...i was stranded at my aunts job n handily had a bobbypin to loosen the wires from the clip...plugged it back in and waited then it started...u r a genius!!!!...thought i would have to pay a tow truck and a shop to get it fixed...
MzBossy Badd what was happening to your vehicle
@@Houston0068 srry so late...i broke my turn signal switch...n the guy that tried to fix it messed up wires n the module when he was taking the old one off to replace it...new part wasnt the right one...so when he put the old part back on it wouldnt turn over and the security light was stuck on even when the truck was off...had another guy replace the old switch and it wrkd for a while then the security light would flash quickly abt three times before going to the next alert and wouldnt turn over...tried this n it wrkd...no issues since...
Thanks for this. I think this fixed my no start problem on my 02 Duramax. I been fighting this for years. 2 different cars. I even took it to Chevrolet once they just threw parts at it. I learned to live with it. Just had to wait 15 minutes every now and then. I think this should have been a recall. Thousands of people have this problem.
Did your truck start and turn off immediately? I have had that problem since Inpurchaed the truck and have jot fixed the issue, but now that my boy is going to start driving it I dont want him starnded someplace because it wont start since he will ise it for school.
I've watched countless videos on this topic, none were as easy as this. It took me 20 minutes to fix my problem and just like that my truck started
Thanks for this video posting
Results! 2003 suburban,so I checked the switch made it more tighter,but my problem was a ground going to the PCM,they are two ground wires behind the block on top and one of them was completely broken.all fix.😁👍🍻
Do you have more info please.
@@ramiresamador2383 Theirs 2 braided wires behind the engine block, like on the corners. Buy the ground wires a napa auto parts. Google ground wires location.
Okay thanks for the info.
Thanks this worked for my 02 GMC Yukon slt I’ve been having this problem for awhile and I finally found a video to do it thanks again man God Bless!!!
Glad I was able to help. Don't forget to subscribe to my UA-cam channel.
If you are watching this lookin for answers, this is it. Mines been doin this on and off for a while and finally it just wouldn’t start. Some research led me to this vid. I can’t say thanks enough for this. Fuck n a.
Mines 99 Silverado, 4.8 2wd, just for info.
Thanks my friend! Have whittled away at this for hours. Your video nailed it!! Thanks for posting.
Just bought a 2001 tahoe the other day and it has a few wires hanging out amd cut. Everything is working loke it should but it looks like i better take the plastic off to see of they bypassed it somehow and double check everything. Thanks for the upload.
I just tried on my 2003 GMC and it worked.thanks for the video
Glad I was able to help you out
Was this all you needed to do? Is it still holding up? I have an 03 Gmc Savana and I replaced the ignition switch already and hope this can work
This fixed my truck, no more security light flashing and it starts right up. 👍🏼
I figured i would try it because ive tried everything else. Holy crap it worked dude! Thankyou for posting this vid. My 2001 suburban k2500 runs again!
5 years later, still driving, no blinking, still good. I would love to know how you're making your gas last sooo long. My 25 gallon tank needs filling every week.
Check your knock sensors. I had to change mines. Was making the computer run the engine fuel mix incorrect.
Was this keeping your fuel pump from kicking on?
Well if that doesn't work then it's your tbc fuse which is located in the fuse box in the engine.. it's a 10amp by the way.. it should get rid of that security light and if your headlights don't work or interior lights then it more then likely is that tbc fuse...
Truck:2000 gmc sierra 1500 5.3
Thank you!!!!! 100% legit. Finally fixed that damn security light and only took 3 mins.
My 2000 Oldsmobile Silhouette minivan message center does the same thing as yours: Battery light, low fuel, and security. What other symptoms did you have? Did the engine crank or start? Mine will not start or crank at all.....
This will probably fix our problem
Muchas gracias por su video me ayudó muchísimo. Gracias bendiciones
I recently bought a 2002 chevy tahoe. Runs good, drives nice, no dents on the body. For myself it only has one problem. Every time unlock the door and open it the security light will come on and horn will start honking until you put the key in and start the engine. It has no problem starting the engine and does not happen if opening an unlocked door. Only if door is locked. Any solutions on how to fix this is greatly appreciated. Thank you.
I wish I could but unless I can get my hands on it n start trouble shooting theres nothing I can do for you.
Thanks anyway brother and keep up the channel.
was your light on when the truck was off? my lights on sold 24 7 no flashing. i can start the truck drive it just fine but it slowly drains the battery and if i dont drive it daily it kills it then have to replace it from constantly dying. i am going to try this after work regradless just trying to pin point it before hand if i can.
My light is off when the truck is not running.
did you ever get yours figured out? mine does the same thing. if I don't start the truck for a couple days it won't start. but I can jump it every time
Question, you stated that the truck had to sit for 20 mins to get the light to go off. Is that with the ignition switch on or off? When turned on the message center strolls through. When powered off the security light stays solid and never goes out.
U need to let the truck sit with the ignition switch off for more then 20 minutes. It will reset after that.
For everyone else out there wondering what’s going on after your ECM swap, for a 1999 - 2000 Silverado, you can swap an ECM from a similar enough vehicle. Generally it will run, sometimes it won’t. Where I’m at, if it doesn’t run after the swap then my dealer can re-flash it for $90. I will post about this in my channel when my engine swap is done
Not shure. Good luck with your swap. Let me know how it goes.
@@TheCuban.45 I completed my swap. The ECM from 2000 Sierra 5.3l did not allow my 1999 Silverado 5.3l to run, but my stock 1999 Silverado 4.8l ECM did allow the engine to run. I believe this is due to the VIN on the ECM not matching the VIN in the BCM (BCM is located in the dash near the steering wheel). I made a video to document the results: ua-cam.com/video/8Uya_inXYl0/v-deo.html
What was the main issue just the light? my 2002 alarm system just goes off for nothing at any given time when using the remote key lock. rouge security system works random. leave it unlocked no problem, only when locked?
Mine was just the light. But others had problems starting the truck.
@@TheCuban.45 Thanks Man, my problem may be something else then
The Cuban .45 do you know if this solution will allow the truck to start after an ECM swap?
Thanks for the video! I got the exact same problem with my 2001 Silverado. Gonna try this today. I'll post back later how it worked.
James Bryant did it work???
did it work please say yes
Very good on getting that light out, annoying wasn't it? quick ?, When you shut off the truck Take the key out and open the Door does your security light start flashing till you shut the door? Or is that something else?
I have a 2000 Chevy Silverado.
My security light never came back at all.
@@TheCuban.45 so I still have an issue, thank you
i have similar issue does this security light some kind of safety mechanism to keep from starting in the case of stolen vehicle? everything is brand new and sounds perfect it could be the only other reason it wont start
There's a time out after u change the parts. Give it a good 30 minute n try it again. If the security light is still on then u still got problems.
I have a 2000 Chevy Silverado , while on the high way , all lights cut out , expect turn signals and break lights truck did not die till next morning , now it won’t start if not driven for hours , security light turns on I’m able to jump
It but no lights turn on low and high beams , no interior lights either any help ?
Sounds like u got major problems in ur fuse box. Check the ground to it first.
Did it get fixed. I have the exact same problem. Same truck and everything
Will this work on a 2000, just bought one for 500$ think the security light is draining the battery.
Yes they are the same thing
The Cuban .45 thank you will try this tomorrow
I’m a little dense, sorry. When I have the issue of my 2002 Tahoe not starting sure you saying a loose connection is the problem? Some of these videos say the vehicle will start for 3 seconds then die, my problem is I turn the key and I get nothing, no start no click or anything. Will this work for me?
I think it will. Give it a try. U got nothing to loose.
Did it work
Tell us if it worked
I have the same problem with my 2002 chevy 1500. Even the low fuel indication issue, but also the temp gauge not working either. I tried this trick, but no cigar. I guess it could be the ignition switch, will try that next. I tried the instrument cluster in another truck and it works fine. Right now, the instrument cluster is removed since it drains the battery overnight.
Question I'm having an issue like this but only with the door open and I was wondering if it might interfere with the reason I have no power to my fuel pump for it to start will this reset the security so that everything will work again
It work for me. If I was u I give it a try
Learning something new all the the time! Thanks Tucson Arizona
my security light comes on randomly while driving, but the truck still starts & runs. I will try this, looks pretty simple. Thanks!
What do they call that housing that you put the three wires in. And what is the housing going into what's the name of that piece?? And where can it be found???
www.amazon.com/gp/aw/d/B01M66NPHT?psc=1&ref=ppx_pop_mob_b_asin_title
Thanks for your video brother 👍
🌴Greetings from Brownsville TX🌴
My 01 Silverado has a sporadic issue of not starting: turn key and hear less than a second of fire, then shuts down automatically. I’ll be stranded for a while. I did this crimp and the same issue returned. Maybe it’s the housing like he suggested.
My 02 Envoy is doing this and I don't have a security light on.
Did you figure out what was wrong with it.
It might be the starter
Timothy Weinert I don’t have the security light on when it starts either. The problem may be the housing because of the magnetic signal within that helps generate the proper voltage.
Gonna try this on my 99 Silverado cause I am having that same issue. Truck starts up, but the Security light stays solid even when off. I am going to try this tomorrow.
Terry Coffenberry II if it don't solve the problem try my video on the cluster fix.
Terry Coffenberry II
ua-cam.com/video/KxGE8bPCGco/v-deo.html
Did it work?
The Cuban .45 what's up ? If that wire is loose will it keep truck from starting even stop it from starting spraying starting fluid into throttle body? Truck just quit while driving . my window was down and it rained like hell inside of truck causing door to keep locking and unlocking the next day . then the alarm would turn on randomly during the following day
I took my truck to the dealer and got it fixed. Turns out a damn mouse chewed the wire in my distributor box. There was dead mice in there.
How do you take the steering console off to fix the problem and put it back on again?
The screws are at the bottom. Then pull it apart.
Did you also happen to have your abs fuse for your brakes pulled as well? I was getting a low speed wobble when braking and had to take my abs fuse out, otherwise I wasn't able to stop cause the abs system would kick in. That was a year ago and now my security light is on and ran down a brand new battery. Do you think this is my problem?
It may b related. But for me it was just the security ligh blinking.
@@TheCuban.45 OK, anyways, I am very thankful for your video because it gives me something else to look at. I needed a new battery anyways, the old walmart battery lasted me 7 years, so I couldn't believe that either. I will check to see if I have the same problem as you. I hope so cause it looks like an easy and cheap fix. BTW, if you ever have trouble with your brakes when you are driving slow and the brakes start acting funny, then all you have to do is pull that abs fuse and it solves your problem. At least until you find out why you are getting a low speed wobble. Which more than likely means you need to install a new hub. Thanks again!!!
How was it turning on before you fixed it.
My 2002 chevy wont start up ,im thinking maybe its this since security alwayd flashing aswell. Turns off on me whenever i break , or just wont start at all
You can try this but sounds like u got other problems too
Have you had any problems since this video? Need to know...
Yes. Check out the following video.
ua-cam.com/video/KxGE8bPCGco/v-deo.html
best fix for this that I seen.
I have a 2007 GMC Yukon with the security light showing I tried just about everything dislike this looks like it could be the problem. Just let me know what the name of that piece in the ignition is called
Best thing to do if this doesn't work it the replace the entire unit. I found it ones in Amazon. Let me c if I can find it again.
I know this has been up awhile but i have a 2001 GMC Yukon. It is
doing the same thing. The first time it did thisdisconnecting the battery stopped it. Now its doing it again and disconnecting the battery didnt work. My mechanic in town said take it to the dealer. Im a disabled senior citizen . is this something i could do? If so how do you take the cover off?
The screws are at the bottom.
@@TheCuban.45 Thank you. I am most grateful. I was a nurse. Not mechanicaly inclined.
is the security light supposed to be flashing while the truck is off? i never had an issue with it not starting cus of it, im not 100% sure if it stays on while im driving, my check engine light stays on so i tend to overlook my indicator lights by default.. something lately has been draining my battery and im trying to figure out if that little security light can be a drain. Didnt isolate any issues through a parasitic draw test, so all i have left is glove box light, hood lamp, and this security light
It's not supposed to be flashing at all.
@@TheCuban.45 i havent gotten my battery back in yet to verify if it flashes while the truck is off or just when i open the door. i dont have a fob so i use the key to unlock, and power locks to lock unless one of them is sticking too hard for the motor, idk if any of that makes a difference. But the truck always starts, ive never had it not start cus of it. all i know for sure is when i open the door i see it flashing when i get in, i need to verify if its on before i open the door and if its on while im driving i guess. Trying to find answers but seems my issue is just slightly different than what most these videos are about
Hey my truck has all the same warning lights as yours and I followed what you did and it didn’t work any suggestions?
Try this fix below
ua-cam.com/video/KxGE8bPCGco/v-deo.html
@@TheCuban.45 just tried that. All the soldering looked good. This all happened while I was sitting in a drive thru. It idles super Low now too
@@TheCuban.45 any more suggestions brother??
@@TheCuban.45 any suggesting big man?
What if you got a viper alarm installed on it and the security light is on when the truck is on and won’t go away expect for when the truck is off any suggestions ?? 🤔🤔
The alarm is wired wrong.
The Cuban .45 In what way is it wired wrong would you happen to know ??
Ricky Rico that’s the same problem I’m having
Does you security light flash when your door is open?
No it's never done that
@@TheCuban.45 ok I tried the relearn process about 100 times but didn't work I also tried connecting the yellow and Orange wire together and tried the relearn and still nothing.
@@TheCuban.45 my light only flashes When I remove the key and the door is open
@@ReflexParkour7 same fam, its aperently the reason I can't program a fob for keyless entry.
my truck is not starting.. the light went away but the service engine soon came on.. still no luck any sugestions please
Jose Martinez youhave to wait till the computer resets.
Check the negative ground cable that goes from your battery to the red junction box. Then follow the negative from there to a bolt on your engine block. Clean it and tighten it. It makes the truck act crazy when it's loose or dirty with engine grime and oil residue. It took me one steering column, key cylinder, fuel pump, fuel filter, fuel injector pressure regulator and a whole lot of reading until I found a video on yt with this info.
Rick C that sucks. When you end up spending four hundred bucks and it’s as simple as a loose connection. At least the new parts are on, I guess.
Thanks for making this video. I am having the same issue with my 2001 GMC Sierra 2500HD. I am going to tighten my passlock connector as you have shown. I do have one question. What did you use as a pin at 4:58 to wedge the connector?
A dental pick end. Brake off the tip n use that.
Thank you.
My 2002 gmc yukon did the same thing I turned it on and the battery light was blinking the security light was blinking low fuel light was blinking, my doors wouldn't lock on there own like the normally do when you pull it into drive my gas gage temp gage wouldn't work either! And when I would pull it into drive it wouldn't light up on what gear I was in.
Check out my other video on fixing the instrument gauge cluster. ua-cam.com/video/KxGE8bPCGco/v-deo.html
it would have been better if you try start it before and after,cause the sound of the truck that it start helps alot, cause my sound like it want to start!
I have a similar problem with my 2002 Chevy Silverado, after replacing the fuel pump, spark plugs, gas filters etc it still wouldn't start... so at this point ill try anything.. I'll give it a shot tomorrow and give feedback. Wish me luck.
Did it work?
Did it work... cuz I just replaced everything u named also
Did it work?
Try this out. ua-cam.com/video/KxGE8bPCGco/v-deo.html
please tell me it worked?
Can it shut down the whole truck if it wiggles loose?
If it's running it will just flash. If it's off it won't start
Will this work for a Cadillac 2000 Seville
Not shure
Thanks man confirmed my problems god bless you
With ligth on will not krank at all or krank and shut off itself after 2 seconds ?
Alex Monroy with the light on it will not crank at all.
The Cuban .45 thank you. Mine does krank and after 2 sec shuts off .still cant figure it what it is .replaced fuel pump, spark plugs unplugged cam sensor so i don think is it
Alex Monroy good luck with it. When u find out what it is let me know.
The Cuban .45 ok
95-99 Chevy Tahoe, Suburban, Sierra, Silverado, Security fix in 30 seconds
ua-cam.com/video/TQ9ASjcSoWQ/v-deo.html
Do you leave key on for the 20 minutes until the security square yellow LED box stops flashing? Thanks
U don't need to do so
Anyone here know about taking the steering wheel off of an 01 Silverado..?
My 99 is doing this ATM but we aren't trying to fix it ATM we are trying to fix the trans and t case adapter that broke due to a u joint blowing out the drive shaft
My husband just replaced the starter. The battery was disconnected. Now it doesn’t start. The battery light and the light that says security is flashing & that is it. My deck turns on but my gauges and everything else doesn’t move. No crank no noise nothing! Hoping this could be it!?
My locks and everything work. Headlight turns on.
Give it a try. It worked for me and many others.
My problem is that I’m having to take the negative wire off the battery ,take a pair of jumper cables connect to the positive and to the negative and wait 15 or 20 minutes to reset the security system because the truck will not stay running ,I need to do away with the security altogether ,how do I do that?
Don't know if u can do away with it. But this may solve your problems
Trying this when I get home tomorrow! My 02 Tahoe was parked for 2yr and I jumped it off. It crunk up fine for 2weeks straight and after I replaced the battery it never started again. Security light is on. I will let you know the results
Good luck 👍
To all Gm owners before u spend any thing even time check the ground wires especially the one behind the engine they might be lose or cut .
Thanks brother from houston tx
Jasun
Can this is some strange way be killing the battery???i have to jump start my truck if I leave it over night with out starting
The security light stays blinking for a while. But I don't think is going to drain the battery
Nice video very good direct information, the only thing I could find as a complaint is all the wiggling and the bad focus but Hey that's what it takes to get it done bro, thank you!!
The security light started to stay on today, then later this evening it will not start or stay running actually. Will this procedure fix thus problem?
It did for me
Could this be causing why my truck don’t turn on every once in a while ?
Most likely it is. That's how my stated.
My 1999 Silverado 5.3 has this. Crank but no start. Have to do a 10 or 30 minute reset half the time. What's the fix?
If this doesn't work u have to replace the entire unit.
@@TheCuban.45 Your description says 2001-2007 so I was checking if it's the same
And it only took you 5 miles down the road to fasten your seat belt?
shut the fuck upp
So would that work like a ECU flash 📸 or is there no comprance lmk pls 🙏
Two different things
GOOD old GM ; They build a critical over riding system and use hairlike wires and crappy connecting posts IN A MOVING environment :: EVERY time I work on GM I swear I want to line up their pinhead engineers and commit a felony ! WHAT, were they thinking ? I have switched to Honda and KIA- AMaaaazing engineering on a KIA !
Good video on my truck it was tbc fuse corroded 10 amp fuse
After 3 weeks of pulling my hair out. This was my issue as well
@@funseeker1969 i had the tbc fuse problem last year yellow security would stay on constant even key off and out no headlights or interior lights truck would run though fastforward a year same symptoms but the fuse is good and now its progressed to a start run 2-3 seconds die just like a pass lock probem but i cant do a relearn as the ligth goes solid any ideas
i had the tbc fuse problem last year yellow security would stay on constant even key off and out no headlights or interior lights truck would run though fastforward a year same symptoms but the fuse is good and now its progressed to a start run 2-3 seconds die just like a pass lock probem but i cant do a relearn as the ligth goes solid any ideas ps the fuse box has been changed
One thing I noticed was the fuses in fuse box started corroding would test ok with a simple test light but measuring the voltage across them was erratic. Decided to pull every fuse and found 5 to 10 of them corroded even a few that tested ok but once pulling them out broke because of it so I took ever fuse out and cleaned every terminal used die electrical grease and installed almost half with new fuses and all issues went away later on I replaced the whole fuse panel because for some reason they corroded on the bottom and internally (once I took the old panel apart to see it was green cancer everywhere) plus another huge things with these trucks is grounds specially the one by the cab mount under the drivers door hope this helps in any way
Would this cause a "no spark" situation
In some cases the truck won't even start.
Did this work?
Yes it resolved the problem and it never came back.
I have a 02 suburban, I replaced the battery now the security system is locked & the truck won't start... Can anyone help me plz???
Remove the battery terminal. Wait 20 then connect it all back.
@@TheCuban.45 okay I'll try that.. Thank you
They cut those wires that you’ve shown on the video. Gonna try to figure a way to get the wires to stay on those tiny barbs
Go to the junk yard n get a new connector and wires from anoter truck n reconect it.
Good work man, thanks for sharing.
Do you know where the vats control module is on there
PCM
Can I email or post a couple Questions Big C ?
Sure you can ask anything. I b happy to help you out.
I have problem w star mi car 2002 Chevy Tahoe the alarm not stop
fuchoco bocamar this wil fix your problem
So my truck starts but the security light flashes still
Try doing this. It solved my problem
@@TheCuban.45 all give it a shot som1 tried stealing my truck and messed it all up SMH
Was it draining your battery?
@@alexdominguez5057 no it was not.
@@alexdominguez5057mines draining my battery any help?
Si what’s the security light on for?
Its a chip on your key for security
Could you put hot glue one the connector to stop the wiggle?
I think that's a good idea 💡
My truck is 2000 chevy 2500 6.0 an its doing that with lose of power to sometimes it will run just fine an no eng lites at all on an it will lose power
Check out this video it may help you out. ua-cam.com/video/KxGE8bPCGco/v-deo.html
Does anyone know if this will allow you to do an ECM swap and fix the issue where the ECM and BCM need matching VINs?
Hi there! What happen did you fix your issue? I just switch my Computer too...I'm trying to by pass the security sistem and Nothing! My car doesn't start...
Envwee I have not put my engine back in yet. I think I’ll end up just using the same one and having it reprogrammed to run like a 5.3l. Though, out of curiosity I may drop the 5.3l ECM in there to see what it does. The dealership claims it should run no problem. For issues like that you should reach out to your local Chevy dealer and ask someone in parts. They’ll be able to tell you right away
I had my security light come on when using a test light in the wiring harness clip under the steering column.
So this may be why my truck isn't starting its saying the same thing I just paid 227 for a new fuel pump
percilla lady we in the same boat
My homie put the scanner on the truck and it said I was misfiring but I see the security light on, is that the problem or is it the fuel pump?
Me too
mine has all the same lights on but its also making a clicking sound like a directional is on draining my battery dead
i tried doing what the video said didnt work
Trying this out,hopefully I can fix it
Did it?
im gona try this shit out i have the exact same shit on the dash and wont start
ill see if it works or not.. its worth a try
Did it work for u
Did it work
2004 CHEVY SURBURBAN, TURN ON,OFF, ON OFF, ON , OFF WITH REMOTE, THEN HAVE TO HAVE JUMP, BECAUSE BATTERY GOIN DOWN, THEN IT FINALLY STARTS...........
Por cuánto tiempo conecta los cables
20 minutos
Thank for share, very good info
Next time you might want to try just sitting your phone on top of the dashboard with the camera facing down maybe that will work
How the fuck do i get behind the steering wheel 😂 ive taken the screws and shit out but no matter how hard I try the fucker wont come loose
Thanks for the fix