Affordaplane TA-1 progress
Вставка
- Опубліковано 2 жов 2024
- Walk around the A-plane ultralight.
Affordaplane Store
affordaplanest...
Become a Patreon supporter:
/ terrya70
If you aren’t familiar with Patreon, it’s an easy way to contribute to creators that you love. There are also a few perks for joining and I would absolutely love to have you as a new member. Patrons help lay the foundation for what happens on the channel, I could not do what I do without them.
If you prefer to make a one time contribution, PayPal is a great option for those that aren't ready for Patreon.
Click the link below for PayPal:
www.paypal.com...
Finally hit that subscribe button, its free and more subscribers means better quality free videos. The more subscribers we get, the more money we make. This impacts you because when I have more revenue I can dedicate more time and resources into creating videos with awesome content.
In fact - your support has already enabled me to add certain audio and video equipment to make better videos.
Our Facebook Group link:
/ affordaplaneultralight...
Products used by TA-1
PNY 128GB PRO Elite Class 10 U3 microSDXC
amzn.to/39pcJYq
GoPro Hero7 Black
amzn.to/3qh3boz
GoPro Battery for HERO7 Black/HERO6 Black/HERO5 Black
amzn.to/33pyNhO
LED Pods Light Bar 4-Inch 120-watt 12800-lumen
amzn.to/39o1LT6
5 Gallon Gas Can, 4 Pack
amzn.to/33n03xe
Super Easy Siphon Hose
amzn.to/3fI2IGZ
Radio holder case
amzn.to/2V9GdBl
Icom IC-A16B (Bluetooth) VHF Air Band Handheld Radio
amzn.to/2HJGpnA
Sena SMH10-10 Motorcycle Bluetooth Headset / Intercom
amzn.to/3mibmOX
Sena GP10-02 Bluetooth Pack for GoPro
amzn.to/2V9NJMj
Angle Grinder
amzn.to/3o7m0Z4
Sanding wheels
amzn.to/3mkmpHh
Wire wheel
amzn.to/33qbO67
Steel cutoff wheels
amzn.to/3fIIoVT
Sand paper disk assorted
amzn.to/3mgxrNN
Alloy 4130 Steel Round Tube - 1/2" x .035"
amzn.to/3qbP1oi
Hydraulic Hand Crimper Tool for Stainless Steel Cable
amzn.to/37ko9Kx
Digital Crane Scale 300kg/600lbs
amzn.to/3o4wI2J
Blue Polyurethane Fuel Line 1/4"
amzn.to/37d7ybu
Stainless Steel Fuel Injection Hose Clamp
amzn.to/2HM6q5T
Barry Controls Motor Mount
amzn.to/39lWN9c
Double USB Converter Module 12V to 5V 3A 15W Power Adapter
amzn.to/36ky97j - Наука та технологія
Definitely need to change those washer on the engine mount, with the vibration and time they will dig in to the mount
I just found your videos and love them. I would take a stripped down q tip and coat all of the quick connect electrical connectors with dielectric grease (I coat all electrical connectors with it). Just to prevent corrosion in the future. They will all be getting hot/cold/warm during regular use, which will cause some condensation, more of course on the wires that draw more current.
Very sanitary build? You may want to run your wire inside of a wire jacket to protect them from vibration. It may be wise to rethink the way the wires are connected to the various components as they could vibrate off.
Beautiful build amigo!! I am currently building an Affordaplane (likely to use a Rotax 503 DCDI,but?)...I am a retired Airline A&P,I.A. and love dinking around with this stuff. You are likely aware of the FAA ,USDOT publication AC 43-13-1b and AC43-13-2b...if not, they can be purchased on ebay for $10-15. MONEY WELL SPENT, if you are not an A&P. It encompasses inspection,repair,and alterations of certified aircraft. Kind of a "bible" on what to do. love the sidestick(which is what I will use as well) My biggest deviation will be ZERO electrics except for that which is required for engine operations. Your "mock-up" phase is going great. I will not be going for the seat-side throttle, but instead will opt for a frictionlock ,left-side dash mount. less distance,less weight,and one less thing to screw-up when I slide my fat carcass in!! Where did you get your wing attach bracketts? what kind are they?.....great build....bob
Bob I can not recall exactly, but I believe I picked them up at lockwood_aviation and had to call as I did not find them online.
Avery nice work, cong
Thread lock, lock washers, and nynuts (military's nylon locking nut) on the prop mounting bolts are fine, with a minimum of three threads showing above the nuts, but SAFETY WIRE THE BOLT HEADS! You will not be sorry.
Did you rig up a carb(s) heater? I remember your engine cutout video mentioning possible carb icing at 1700 ft elevation? Seems too low for icing, but your more familiar with your area. Houston is near sea level and humid, right?
I'm in AZ at 4633' elevation, probably quite a bit higher than Houston, TX down near the Gulf of Mexico or some body of water. Love your videos, trying to get my own place and build my affordaplane, have plans, will utilize your store and aircraft spruce, got a catalog. Your store is online only?
Your engine out landing looked a little scary and it sure beat up your landing gear, but a tree collision would a been much worse. Thanks for your videos, Terry, John Bell from Sierra Vista AZ.
At 4:52 in the video, you show some plastic spacers in the fuselage. Just wondering where you got those. Also, any info on the spring steel for the tailwheel would be appreciated. Thanks for the videos. PS Just give the cats some toys and they'll stay off the plane, lol.
Hello Terry.
Really good job!
Did you fly now?
What kind of Hirth engine is that?
A 2704?
Greetings from Germany
THIS IS 100 % THUMBS UP. Every one has little tweaks after a build. I say good work.
Terry, I would suggest fender washers on your motor mount rubbers. You can get them at Orscheln Farm and Home Supply or Westlakes Hardware. If you want aircraft grade try Wick's or Aircraft Spruce. They need to almost completely cover the rubber damper. You have done a great job, it really looks good.
Mr Adair, I heard your name mentioned related to the Affordaplane and I'm so thankful for these videos. This is my year to build! I think that I've settled on the Affordaplane. Once I get underway I wonder if you would mind the occasional question? Anyways I really enjoy and appreciate your content.
Nice build. Where is the safety wire though? I've built race bikes for years and safety wire is a must, would think it's even more important on an airplane.
The washers on the the grommets should be large enough to not pass through the hole the grommet is set in. I would consider that a safety concern during a crash so the engine can not pull off the mount.
I would use circuit breakers instead of fuses. Then you could at least reset it in hopes it was just a spike that tripped it.
As far as the wiring goes, a good tight mechanical connection is best. That means, a quality set of crimpers and connectors without those plastic covers. (they look so tacky too) They don't let you inspect your crimp. Shrink tubing should be used instead to cover after you are happy with the crimp, and it should be long enough to support the wire to connection joint. Failure usually happen at the point where there is no insulation on the wire at the connection. Due to movement and vibration. Solder can be used but keep it from whicking up the wire much. If it goes up the wire it creates another point that can break. Keep the solder well within the length of shrink tubing and it should be good.
Best of luck with it.
Hi Terry, I would suggest with the foot pedals you might like to put a bar across to take the pressure of your heels. In some situations I have seen foot rest holes in the floor just infront of the pedals. With vibrations thru the floor your feet could get displaced. With the fuel pump, I would suggest you have a vacuum version connected to the engine crankcase, and then also use an electric version for take-off additional power. You should be able to check the air vent to the fuel tank. Should show a positive open and closed position. hope this helps. great to see another affordaplane getting up to spec. I have a Flying Flea Bifly tandem wing, similar spec. G-POUX
All the best Gpx.
Soder or it’s vibrating lose at 3000
nice job. all the washers I've seen are always the size of the grommet.
Very nice work and some great ideas, I doubt it will be part 103 legal but I can't wait to see it fly.
Hi Terry
I’m a new subscriber to your channel. I’m really impressed with how good your plan looks.Im really torn as to which plane I will purchase . I’ve been giving a lot of thought to a Kolbe firefly but after looking a the different Affordaplane builds on Utube I have a close competitor to consider. I agree with your engine choice as I would rather have more power than just enough.
Hey thanks for posting. Can you please tell us more about the EFIS app you're planning on using and on what device? I'm taking lessons in an Aeronca Chanp. I tried out Aircraft Cockpit on a Galaxy S5. It seems the vibration confused the gyros which made the slip ball and the artificial horizon go bonkers. The compass, altimeter, VSI and Ground speed indicator worked well though. THANKS
ua-cam.com/video/5EyxTI8fL34/v-deo.html
Thanks Terry
Love you gas tank !!
Would you mind share info on part number for it? I'm working on 2 projects that could use this gas tank.
Thanks
yrs ago i bought the plans, then decided to at least first take a ride in a plane. small cessna paid for a local trip around a small airport. the ride screwed my equilibrium for a week, decide no planes for me. i switched to rc planes and helicopters.
Safety wire everything you can. Ask a crotch rocket motorcycle rider for examples...or better yet go to a track. When you are off the ground a loose nut can kill.
Add some vibration isolation to the Otter Box mount and thank me later.
How about a PROPER wiring harness!!
Wtf
Thanks for your advice, you will find these taken care of in my more recent videos.
Good job man ,wonderful, thank you lot's for this lovely video and sharing with us ,god bless you and your family
You are so kind
Great video and awesome detail and craftsmanship. I just ordered my plans so will be following you close. Do you plan on using a laptop belt or 4/5 point harness for safety belt?
5 point harness
Just throw it the air felter usedless cause additional weight...weakminded
Great project, and nice workmanship.
Keep an eye on that exhaust, looks like it might need an additional bracket.
Yes, It is still in build stage and muffler is not even bolted down yet, just on for reference.
Terry, the plane is looking right-on, wish we could see it with the wings all the best to you
Great job Terry!
Can you please give us some more details about your nice seat?
Thanks!
Bass boat seat purchased at Bass pro shop
use double bolted cable guides...one of them loose looks like a screen door catch to me.
Where do you keep your plane. I live north of Houston and I would like to see one already built.
Small airpark near Pearland LVJ.
Nice work, good job!
looks nice but not sure about the hirth.
If you research continental o-200 engine mount you gonna see what I mean
Weld that nut 🥜 on the mount screw on the engine base
Spruce PN: 530741
I LIKE MORE WITH THE LEVER IN THE MIDDLE SEES MORE TRADITIONAL
Floats ??? Consideration
Gas tank cap vented?
Tail wheel, Hock puck with the center drilled out. I used to do that in my 2-33E.
How much total cost
About 8-10K
Very good
Awesome
You Really do not want "spade Terminals" in your electrical system......
रियल एरोप्लेन कैसे तैयार करते है|
Do you have the other videos posted up that you mention in the video? Can't seem to find them on your channel. I'd love to see the build from the start
I have an album titled affordaplane plane build on my Facebook account. Facebook.com/terryadair.75
Terry Adair darn it. I don't have Facebook. Thanks anyways.
Did not start posting on you tube until later in on the build, you can see more pics on my face book page. facebook.com/terry.adair.75/media_set?set=a.10204672798773833&type=3
Terry....I just finished your video....I worked for Continental @ Bush,and grew up in Houston!! Now in Idaho(dont miss ANYTHING about Houston,except the mexican food!)
Dub rule pump rule gas ⛽️ fail x2
I would say if you have to ask there to small lol. but no. To error on the side of caution I would go to home depot or lows and get some washers that are close to the size of the rubber bushing but that's just me, you can do what you want. Good luck. 🙂
Nice ho made plane bro!!!