BEST 40$ Brushless Combo and Upgrades For Your Arrma Typhon/Granite Grom!👊
Вставка
- Опубліковано 9 лют 2025
- In this video we install a 3S Brushless system and other great upgrades into The Arrma Typhon Grom.
#rc #rccar #video
Arrma Typhon Grom GIVEAWAY!👉 • ARRMA TYPHON GROM GIVE...
Another great tiny basher👉 • MJX HYPER GO H14BM!😯 T...
I overvolted this ARRMA GORGON👉 • Arrma Gorgon 4s!😱 Now ...
6100kv king val Brushless combo👉www.amazon.com...
if sold out I recommend this motor/esc👉www.amazon.com...
Grom Steel diffs👉www.arrma-rc.c...
Hot Racing ESC/Receiver deck👉www.amazon.com...
DumboRC transmitter and receiver👉www.amazon.com...
Kyx steel cvd axles👉www.amazon.com...
KYX aluminum shocks👉www.amazon.com...
CHANMOO wheels and tires👉www.amazon.com...
OVONIC 3s battery👉www.amazon.com...
Temp Gun👉www.amazon.com...
GPS USED👉www.amazon.com...
Lucas White Lithium Grease👉www.amazon.com...
Thank you so much for ALL your support on this channel!! 🙏 You guys make this channel!! If you have any questions or comments on RC or this channel please feel free to contact me Byron Nye at reactionrctv@gmail.com.😊
No BS, Just RC!
Please SUBSCRIBE!
When u fill shocks always pull the piston and valve completely down then fill oil to the top before pushing back to release air bubbles before screwing the top back on.
Excellent thank you very much for the tip!!👍 Thank you for watching our video also and welcome to REACTION RC!👊
Your ideas and videos are awesome for the RC community. I hope you have time to share your ideas on the Typhon GROM and Rlaarlo AK-787 with foams and upgrades. I have upgraded my AK-787 with a PPS Habao motor mount, TP 4040 motor and Castle Mamba 8s ESC. I don’t have any ideas on whether the stock differentials need to be rebuilt and change the oil? Would appreciate your feedback on those bad boys! Thanks, brother.
Your 787 sounds like a beast!! Thank you so much for watching our video! 😊 We're just getting ready to start filming again and am glad to have you here! I will definitely be doing a update video on the Typhon Grom and 787!! Welcome to REACTION RC!👊
I just did this upgrade. Thanks for the video sir
No problem your welcome! Thank you for watching our video!👊
@@Kbeezzy23 is it easy to do ???
Somebody might have mentioned it but a heat sink would help the motor temp issue. Also, you could cut a small hole in the body above the ESC fan.
Thank you so much for watching our video!! I'll be getting back to this build soon and great minds think alike! I believe you will like what I have in store. A heat sync would definitely help out ten fold and I like the hole cutting idea! Thank you 👍
Very nice job B! 👏
Thank you! Thank you for watching! 😊
Dude that thing is a beast. Great vid bro
Definitely! I've still got more for it!
I put the same system on my Mojave Grom and I’m getting solid 48MPH, and everything else stock, not bad for $38 👍
That's Awesome! From what I've found king val is legit! I'm getting ready to do a MOJAVE GROM now along with the Losi NASCAR. I'm looking at some cheaper systems I think will work well for the NASCAR. Definitely not bad for 38$😀
Awesome video! I’m loving the new intro 🎉
Thanks 😁 babe
Just got a typhon and granite. Thanks for this video, great info!!
Your very welcome!! I really like the Grom platforms! They can take big power with the right upgrades and keep coming back asking for more. I can't wait for the Mojave Grom to arrive and I've been told it comes with the upgraded diffs!👍 We'll have to find out when it arrives.
back in the day with 5th scale we had caps with bleeder screws
Yeah those new hot racing shocks had the bleeder caps. They are really nice! 👍 Thank you for watching our video!🤙
Great video!!! Kept me interested and excited to the end. You Two are making it!👍👍👍 amazing job, oh and the links are great, im glad the metal diffs are available 😀
Dude thank you for watching and the kind words!! Yes the diffs are finally in stock, it took a little bit but they finally are. It stinks though, the motor/esc combo is sold out now on Amazon. I'm hpeing they restock soon!👍
So I've just stumbled on your video, the typhon grom was going to be my next purchase, and seeing a bolt in brushless motor and ESC combo for just over £40 (uk exchange rate) has well and trully sold it! Cheers buddy, great video.
Cheers from the US mate!! Welcome to REACTION RC and thank you so much for watching our video!! I really like the Arrma Grom platform, it's really tough and can take big power with the right upgrades and like you said a brushless combo that bolts in... SOLD! You won't regret getting one and come back here if you have any questions on it and I'll try my best to help you out!👍
@@ReactionRC cheers 👍🏼
Yep I'm subbed brother 😊
Keep em coming 🎉 .. great content
Awesome thank you for the support brother!!
Awesome video man! That new intro is sweet! Nice mods, 47.6mph is mad for not even full throttle 😮 60mph will deffo be hit man!! You'll get it for sure
I'm thinking so too! We gotta solve that heat problem. Thank you for watching my friend!
Need the metal sun gears for the differential
The upgraded diffs I installed have all metal gears, the sun gear and planetary gears are metal. Thank you so much for watching our video and welcome to REACTION RC!👊
Nice job dude
Thank you my friend and thank you for watching our video!🤙
Thanks for the Video! I just installed the exact same combo but the cover wont close. The esc is too high. How did you do that sir?
I ground those front wire nubs down to the top chassis plate. Take them completely off, now you have a little bit of room to move the esc forward just a little. I also put I think 2 washers in all the hardware on the latch on the body and the back body notch. It was tight but it fits almost perfectly. If you still can't get it let me know and I'll try to help some more!👍 Basically you just gotta get rid of those wire holder nubs in the front so the esc can sit there.
@ I indeed removed those little nubs, but unfortunately it was not enough for the cover to close. 100% the washers will do the trick. Thank you very much for your response.
It worked! I 3D printed M5 washers. They give just enough room to close the cover. Thank you!
That little sucker rips 🔥
Definitely and such an easy install! Thank you for watching!! 😊
@@ReactionRC You’re welcome 🙏
@@ReactionRCThis is my wife by the way 😁 She loves RC also.. 👍
Ohhh excellent!! Glad to have her aboard
OSHA would be proud.
Definitely! I hate boogering my hands up lol
Do i have to get a seperate receiver to do this or can i just pull out the old system out and slap the new king val system in?
Sorry if this is a dumb question 😅
There are no dumb questions here. If you want to use the king val system yes you would need a separate receiver and transmitter. The esc that comes in it is a two in one esc and receiver for a brushed system. So when you remove the esc you also remove the receiver. Now you can still keep the slt-2 transmitter if you get a compatible receiver and bind it. I think the spektrum sr315 receiver is compatible. Thank you for watching!
@@ReactionRC thank you very much!
Hey man, you arent all done with the channel now are you? Been a while, hope all is well man. Looking forward to the next one whenever it may be.
No we just ran into some life problems lol. I have some new content coming very soon! Hint-mojave Grom 223s blx
I have an inexpensive esc/motor combo i want to put in my typhon grom. I ran into the issue you spoke on, with the pinion gear not fitting the motor. I need the next size up, do you have any recommendations on where to order one from? Any help is appreciated.
I get most of my pinions from eBay or pinion sets from Amazon, amain hobbies, horizon hobby or my local shop. Do you know the shaft size of your motor? Most important things are shaft size and mod. If your putting it with the factory spur gear you will want a .05 mod pinon and then whatever the shaft size is of your motor. Like if your shaft size is 3.175mm then order a .05 mod, 3.175mm shaft, 18 tooth pinion. Search that on Amazon or eBay and something should pop right up if it doesn't let me know and I will look up my orders for the shop names. Thank you for watching! 😊 Usually the next size up motor shaft from 2mm and 2.3mm is 3.175mm. You can always measure the motor shaft also to make sure.
What pinion did you get?
Stock 18 tooth pinion. This motor esc combo has a 2.3mm shaft so it's just plug and play!👍
good stuff. fyi the motor/esc combo is no longer available on Amazon
Dude thank you Soo much for watching our video!! 😀 Ohhh no there out!! Man they had like 20 of them. I'm wondering if people saw the video and ordered them! Hmmm thank you for bringing this to my attention. Maybe I can make a post about a different combo instead that's just as good! They do have the hobbywing 2435-16bl30 combo but that's 65$.
@@ReactionRC all good! Is the hobby wing combo a direct fit?
No it has a 2mm shaft. But Losi makes a 2mm 18 tooth.05 mod pinion that will fit on it. Other than that it's a direct fit. Any 2435 motor with a 2.3 mm shaft should bolt right in. I made a post with the motor/esc combo I would buy since this one is sold out. I'm going to put the link in this video as soon as I can.
Where you get the ramp sir??
I actually built it out of card board and duct tape! I'm going to make a tutorial video, a lot of people have asked about that. Thank you so much for watching!
@@ReactionRC amazing thanks
On yoir second motor esc choice, do you think thatsca better setup for just dirt bashing???
Thank you.
Great video
Most likely because it's a lower kv if I remember correctly. The higher kv is more for speed running I think that's why she was getting a little hot when I was bashing on 3s. High kv is ok if you have the amps to push it. That was only a 35 amp esc. I want to try a 45 or 60 amp paired with around a 5500 or 5000 kv motor. I think that would be the ticket with this little guy!!👍
Hi and thank you for your useful tip! :) After watching your video, I oredered one of theese set. Only I don't have the programming card and I don't understand from the instruction if I can use it with 2 s lipos, is the controller default set to save the lipos?
The king val esc I installed will run 2s lipo and 3s lipo. It automatically can tell if it's 2s or 3s. You don't have to do anything different to run 2s or 3s. I hope this helps, if you have any more questions please feel free to ask! Thank you for watching our video and welcome to REACTION RC!🤙
The typhon grom comes with a 18t pinion and I just bought a 20t pinion with my stock motor and try that for a few more mph 😮😎👍
Ohhh definitely! You will probably gain about 1mph for each extra tooth. Should definitely liven it up for you! Make it snappier!
@@ReactionRC I seen a guy on another UA-cam channel and he got 10mph on 2 teeth I tooth on your pinion is like 6 teeth on your spur gear bike riders know that when they get ready to race and you should know that also
It's just that most people aren't satisfied with 5 or 10mph they always want more to tell you the truth I'm happy with the speed stock gears the losi mini t and b needs some help I have one of those also
Ok pas mal , j adore +1 abonné french
Thank you my friend for the sub!! Thank you for watching our video and welcome to REACTION RC!!!💪
Is there a link to the list of parts on Amazon? Great vid! Ty l
Yes there's links to all the parts in the description of the video! Thank you for watching our video! 😊
Don't know if it's bugged but I don't see a link in the description. Sorry to bother
How much is that in uk £££s I’ve got the brushed version ???
I got it off of Amazon. I'm sure it's not much more expensive. Thank you for watching our video and welcome to REACTION RC!! 🙂
Oh crap How did I miss this? Must’ve missed the notification!?!? Watching now bro…
Excellent! 👍
I use fishing reel grease in my rc car parts 😮😅
I never thought of that!! Hows it work?
@@ReactionRC it looks like vaseline and don't come off the gears even at high speed lots of it stays on the gears for a longer period 😐
Nope u need those axles. I snapped mine quickly after pushing 3s brushless. I did front and backs and did metal diffs. U will have a blast with it.
Awesome good to know! Thank you for watching! I really like these little Grom platforms!
Very cool
Thank you very much my friend and welcome to REACTION RC! Thank you very much for watching our video!👊
Did you ever finish with the upgrades? You're newest video is 4 months old. I'm curious.
The video is almost done! We ended up having to move unexpectedly and it interrupted all my videos but we're getting things sorted out and about ready to get it started again! Thank you for watching and your support!!
I’m getting ready to order same shocks and axels. Did everything work out?
The axles yes but I would go with the hot racing Grom shocks. The springs in these are a little stiff in my opinion
@@ReactionRC thanks appreciate the information
I wonder if arrma is going to make an infraction grom😆
Dude you get bonus points!! 😉 That is an absolutely awesome suggestion!! 👍 I'm right there with you!
@ReactionRC 😆 or even an outcast
@@gamercat7004Ohhh yeah 👍. They will all be awesome!
The Grom Mojave can probably run the same brushless system what do you think?
Oh yeah it definitely would work, I would maybe go a little lower kv if your mostly off road running because you saw it did get a little hot. But yes definitely!
@@ReactionRC thank you
Great video man! How has the diffs been holding up?
Thank you my friend and thank you for watching our videos!👊 They are holding up great so far! No breakages what so ever. They are the upgraded diffs
Why are you wearing gardening gloves to undo the shock screws?
We get them for free at work...🤣 They work great for this because they are thin but still have rubber on so you don't mess your hands up. You don't wear gloves when working on your RC? Uline makes warehouse supplies, I'm a equipment operator. Thank you very much for watching our video! Welcome to REACTION RC!👊
@@ReactionRC no gloves for me
There is air in there because your leaving an air pocket in bottom of shock by not pulling it back to bottom ..
Ohhh ok. Thank you for the tip my friend!👍 I'll have to put that in a future video.
@@ReactionRC just the way I have always done shocks. My dad said he does them this way I have never seen them done this way so if it works it works.
@@jakesrcaddiction I'm glad you brought this to my attention! Thank goodness for dads! 🙏 Thank you so much for watching our video and welcome to REACTION RC. We really appreciate your support!
Reaction RC. your channel was very hard to find because there is another Reaction RC on UA-cam and his channel is all that comes up when typing the name.
Yeah I found out about there channel after I made this channel. I'm thinking of changing it to Byron Nye tv or amateur RC. Or another name because your right I've searched my channel and his is all that comes up but if you put Byron Nye in mine will come up. I think once I have more subscribers than him mine will take that spot. I'm not sure though. Dude thank you for watching!👍
6100kv on 3s I'm sure is to much. That's a 2s setup for off road forsure.
Definitely! It did really good off road on 2s. Really all you'd ever need. 3s was a little over kill lol. Thank you for watching our video and welcome to REACTION RC!
Is your wife Filipino😂😂😂😂😂
No lol. Unless you mean because she flips so much lol
Only came to watch the 3s swap thanks for skipping it.
Yeah I really do apologize for that! The system bolts right in you can even use the same pinion that was on the brushed motor. Do you have any specific questions about the install, maybe I can help. Again my apologies.
Use the legit Toyo Proxes made by Proline...Those ones are a Chinese cheap ass knock off!!!
I've wanted to try them it's definitely on my to do list! Yeah these ones are not so good... Lol. Thank you for watching our video!👊
Love the info - thank you. That said, and obviously it’s just my opinion, but your shock setup sucks.
Yeah I really don't like those kyx shocks! Thats why I got the hot racing ones and they are much better. I wouldn't buy those kyx shocks go with hot racing. The springs in the kyx shocks are just way too stiff, but that's why I make these videos so now you know lol. Thank you so much for watching our video! I love the community of RC enthusiast's we are building on this channel to share our ideas, fixes and experiences with each other! Im almost done with the new build and I think you will like it much better!👍
@@ReactionRC you don’t need to explain anything to me, I just appreciate the content! Actually, this video prompted me to order the esc and motor you recommended. I hope it’ll be torquey enough for the new Arrma Mojave Grom I just ordered, and not just a top end speed motor. The 6100kv figure gives me pause, but for 40 bucks, who really gives a shIt?!
It still had good torque at lower speeds. You might have to put a 17 or 16 tooth pinion on instead of the stock 18 tooth but like you said it's only 40$. Dude I can't wait for the Mojave Grom to get here! I've never had a Mojave yet, any size and I'm really excited for it!
@@ReactionRC I’m a weirdo - I have both the 4s and 6s versions, and I love them! SCT’s are my jam. The 6s is maybe the most fun RC vehicle I’ve ever owned. When tuned correctly, it’s a hoot. Yes, it dives and wallows back like a big ole 1970’s sedan, but it hooks up and just flies, and it eats undulations in the ground like a desert racer should. Get one, you won’t be disappointed. ;)
@@PoliticalDissidentI'm going to take your advice on that!! I think I wanna try the 4s model first I really like arrmas 4s range!!
please buy a used iphone or something to film the car outside better .. please
I don't think it does a bad job. I'm not a big iPhone person but which clips are you talking about and what is wrong with them?