TOP 10 SPECIALTY ELECTRICAL TOOLS! Uncommon Tools for Electricians
Вставка
- Опубліковано 6 чер 2024
- Today, I show you 10 of my personal favorite electrician-focused tools! These tools help me get my job done at a high level of quality! Tool brands include:
Wera
Knipex
Milwaukee
Klein Tools
Bosch
Gardner Bender
and More!
#electriciantools #diy #electricity #electrician #tools #professional
Very solid video, for your receptacle I prefer just getting an extension cord instead of Romex
If you run metallic conduit a hand held band saw is a great time saver, also good for unit strut, threaded rod, seal, tight, large drop cables, …
@@Cavett24 GVC ? What ?
Damn imma add that hot stick to the list of 300 items i want😂
Great set of tools. I really like the cap for driving ground rods with a sledge hammer. 👍
I soak the ground rod base with water to soften up the soil I can drive a ground rod in Texas clay with a 2 pound hammer and a little water
That hot blanket is sick, I didn’t even know that was thing I always assumed you would just use a heat gun 💀
I've been using a blanket for years. they also work great on burritos, if you wrap the burrito in foil.
It's slow as fuck if you have a lot to do.
I've got some heat guns from when I worked in a foundry (they tossed em cause the ceramic tubes had some cracks). They'll ramp up to 900F. You have a high / low setting and a high / low fan setting, and then a damper on the intake, so you can adjust actual heat. They're absolutely amazing for doing PVC. Especially on equipment where it requires a hell of a lot more than simple bends.
@ObservationofLimits I've always found heat guns more limiting. A good blanket in good condition gives me a much smoother bend, and for compound bends, i can just step it down the pipe.
Addendum: I've had cold days when a heat gun just couldn't get enough heat into the pipe without scorching it.
Small fence post driver works well for ground rods too.
when the ground rod hits a rock, I get a small clamp and clamp the trigger on the rotohammer, then adjust the speed control so it doesn't bounce itself off the rod and go do something else for a while. with some models, you can stick a pair of linemans pliers in the handle and hold the trigger.
Just cut the male end off an extension cord and put a tri-tap on it for temp power to the panel.
Good Idea 👍🏻
Интересно. Спасибо за ликбез!;)
such a good video. A ton of valuable information here. You just gained a subscriber.
Good tool suggestions. I learned some things from your video. But if you could eliminate the (unnecessary) background music, it would be much easier to hear what you are saying.
Im glad you enjoyed, and Thank You for the feedback
I hesitate to buy the cable stapler, because it multiplies the cost of stapling, but I might eventually buy one for crawlspaces. on the other side of the coin, I carry an M-18 framing nailer in the truck. it makes adding blocking a heck of a lot faster and easier.
your temp drop cord needs a 4S box, and a GFCI in an industrial cover. it also needs to not have the nuke and ground twisted together. then if you want to get fancy, get a chinese finger trap strain relief and set it on the panel end. and hey, presto, you have an official completely compliant temporary power installation.. I usually make them with 12-3 UF and use a 2 pole breaker and two GFCIs, though. never had an inspector complain.
that breaker finder is designed to sweep the entire panel, and adjust its own sensitivity until it zeroes in on one breaker. I've got about a 95% success rate using it.
That ground rod driver is also useful for concrete form stakes and there are driver bits that are for the 1 1/8 and 1 1/4 hex for air and electric jackhammers and there is a Hilti shank that is similar to the SDS max on their demo only hammers.
But they easiest to drive a ground rod is with that sledge hammer target you have and s mini excavator with a plate tamper yes it takes to people but it goes in shale easy .
I still have my greenleee ratchet set, but I also carry a milwaukee cordless, and I keep a pair of P&R bits in the cordless set for the pilot hole. I've also upgraded from my ratched cable cutter to an M-12 cable cutter. partly because I hit a messenger wire with my hand cutter and the M-12 was the same price.
Great Video. Use them all. I appreciate your segment on the NM sheath splitting, I get a lot of service calls for niched conductors.
Klein used to make the Cat# K90-14/2 with a 90-degree tip which works great for getting up into a box to strip 14/2 NM. I believe they made one for 12/2 but I can't find it with my tools. Not must 14/2 is used any more so it doesn't get used much anymore.
y
You made a very thorough video thanks.
Was a toddler holding the tools? The tools looked huge.
I do wear size small gloves, haha
Great list!
Nice list. The only one I was unaware of was the ground rod cap...great idea. My temporary receptacle is an 1110 box/cover with a short length of BX (armored cable). The breaker finder is good but much more useful if you can find one with adjustable sensitivity.
The stapler is the only item I would forego since I don't do much Loomex (Romex) work (and speaking of that, was that paper inside your cable? In Canada we only have the bare ground wire inside our non-metallic cables, aside from cabtire). I would add step bits to the list instead...very handy for steel stud work.
Most new 12/2 and 14/2 in the US has paper covering below the plastic outer sheathing, and another paper layer over the bare ground wire. Im not exactly sure of the function of the paper, myself. Thanks for your comment!
that breaker finder self adjusts. I got one last year, and i have about a 95% success rate with it. also, the paper in the cable is just to keep things from sticking together.
Ball end?
BALL END?
We're disowning you
🔥🔥🔥
Circuit break locator all the way
Good job,Kid. I've been an electrician for 45 years. Good vid Kid, for old bastards like me. New info
How old are you. You don't seem old enough to have an electrical company. Not sure where your from but here you have to be a working journeyman for over 2 years before you can even start your own. I have seen every tool on the list, but still a good video. Thanks
I am 22 years old, completed my apprenticeship requirements in North Carolina in November ‘23, and Passed my License Exam first try in January ‘24. I started Palmer Electrical in February, and just do simple residential service work while I learn to run a business🤙🏻
@@PalmerElectrical GOOD FOR YOU YOUNG MAN!! That is very admirable. Where I am you are not permitted to hold a contractor license until you have Been a full Journeyman for over 2 years. I wish you all the best in your business and career.
Hot blanket wow
1/2" to 2" with no skips?
...
Me looking at my greenlee set with a billion sizes between 1/2 - 2"
We really ought to label these kinds of vidoes as house mouse or commercial
if you cut through the insulation, you're putting too much pressure on the knife.
Bruh, you should be able to nipper 6-3 by hand
Angle grinder with cutoff is a better option. Works with everything. Works faster.
Wash your hands, dude!
It’s not a cooking channel