Hi. Is there any way you can override the use of these lights via the keypad? My status lights stopped working, and the replacements don't work either. Thanks
@@JasonTech Hi Jason that is correct. i am using an ET remote that had been programmed already, but now i would like to continue using the remote, but have the Siren notify me when the system is armed or disarmed.
Please produce a video tutorial for the installation of one or more PF 5108 expander to a DSC 1864 including the programming of the PF5555 Key pad to accept the one module and reflect the new zones as a numeric sequence to the first 8 zones.
Thanks for the video. Question what about using the pgm 1 or 2 through a Connect2go module as a remote toggle function to drive a 30 watt outside siren via a relay? Application: outdoor video cameras that are internet accessible for monitoring, we have an issue with folks loitering by our rear door at night. I would like to be able to trigger the outdoor siren via the connect2go app. How would I configure the panel from the connect2go module? I would like to set the siren to latch for a specific time period (90 seconds) when I trigger it via the app. I just cant find the addresses that need to be programmed to latch that ground off of the PGM 1 or 2 (PC1616). Obviously PGM provides switched ground to a relay which would drive the siren. It's the configuration I am getting stumped on. Thanks
Ok John * 8 - installers code section 170 - 090 ( this is for the timer) section 009 - 19 - 00 section 501 -- - - 3 4 - - - - on the app hit Toggle PGM / type in 1 then proceed. Let me know if you have any problems or if you want me to make a video on this.
Hi Daniel. There's a few steps, You have to set PGM 2 to Partition 2 and then setup the LED light. Do you know how to set PGM 2 to Partition 2? www.alarmhow.net/manuals/DSC/Intrusion%20Panels//PC1832/Application%20Notes/v4.2%20PGMs.pdf
I cant clear this beeping sound from my panel. I also show a window tamper when I only changed the battery. How dobi reset the tamper alarm and how do you properly change batteries in the window sensors? Thanks
Hi, is there a way to have the alarm show a different colored LED when unarmed? Also, is there a way to have push buttons added to the DSC board that would disarm and arm the alarm?
Hi. Is there any way you can override the use of these lights via the keypad? My status lights stopped working, and the replacements don't work either. Thanks
thx for fast reply
You're Welcome!
Hi Jason, any utorials on how to set your arm/disarm to sound on your siren?
Hi Clayton. What you want is, when you arm and disarm the alarm you want the siren to Squawk?
@@JasonTech Hi Jason that is correct. i am using an ET remote that had been programmed already, but now i would like to continue using the remote, but have the Siren notify me when the system is armed or disarmed.
There's 2 option. I will did a video for you and on post it this week.
@@JasonTech thanks so much...looking forward to it
How to program partition for main house and 2 different suites ??
eg. 123456789 10 11 12 17 on the house side
13 14 and 18 is on one suite and 15 16 19 on another suite
Hi. There's a few steps to do that. Question: have you ever programmed a system before?
@@JasonTech yeah i did
Do you know if this works on DSC NEO boards?
Hi. Yes it will.
Please produce a video tutorial for the installation of one or more PF 5108 expander to a DSC 1864 including the programming of the PF5555 Key pad to accept the one module and reflect the new zones as a numeric sequence to the first 8 zones.
Sure. But what keypad are you trying to install? I never heard of a PF5555.
Hi sir , the Led we need to add serial resistor with led ? or just led only connect to aux+ pgm1
Hi Doug. If you are using a 12v Led, you will need nothing but if your LED is less then 12v then you will need a resister.
Thanks for the video. Question what about using the pgm 1 or 2 through a Connect2go module as a remote toggle function to drive a 30 watt outside siren via a relay? Application: outdoor video cameras that are internet accessible for monitoring, we have an issue with folks loitering by our rear door at night. I would like to be able to trigger the outdoor siren via the connect2go app. How would I configure the panel from the connect2go module? I would like to set the siren to latch for a specific time period (90 seconds) when I trigger it via the app. I just cant find the addresses that need to be programmed to latch that ground off of the PGM 1 or 2 (PC1616). Obviously PGM provides switched ground to a relay which would drive the siren. It's the configuration I am getting stumped on. Thanks
That's something I have to play around with. Give me a couple of days and I will get back to you.
Ok John
* 8 - installers code
section 170 - 090 ( this is for the timer)
section 009 - 19 - 00
section 501 -- - - 3 4 - - - -
on the app hit Toggle PGM / type in 1 then proceed.
Let me know if you have any problems or if you want me to make a video on this.
I will get back to you, Thanks..@@JasonTech
Okey Dokey, works like a swiss watch, thanks Sir.. Cheers @@JasonTech
You're Welcome
Hi sir how do I program the led lights on DSC 1864 panel. Two different led one for two partitions
Hi Daniel. There's a few steps, You have to set PGM 2 to Partition 2 and then setup the LED light. Do you know how to set PGM 2 to Partition 2? www.alarmhow.net/manuals/DSC/Intrusion%20Panels//PC1832/Application%20Notes/v4.2%20PGMs.pdf
DSC actually makes a tri color status light that includes "Ready", "Armed", and "Alarm" indication. Only works on partition 1 though.
Hi Christopher. It should work on all partition, you just have to program it to the partition that you want.
@@JasonTech It’s not programable. It just connects to the key bus
What panel do you have? Do you have the installers code?
@@JasonTech PC1832. The status light is a PC5601
Hi Sir, I do exactly your video show, but my LED light solid not flash? how to make it flash ? Best regards.
Doug
Hi Doug. There are 2 types of LED, flashing and non flashing. In the video I'm using a 12V flashing LED.
I cant clear this beeping sound from my panel. I also show a window tamper when I only changed the battery. How dobi reset the tamper alarm and how do you properly change batteries in the window sensors? Thanks
Hi. There a tamper switch next to the battery. Make sure you put the cover back on right.
Can i put led strob light on out put to horn
Hi Billy. Like a strobe and siren combo or just a LED?
@@JasonTech led I want to use red for fire and blue for burger
Hi, is there a way to have the alarm show a different colored LED when unarmed?
Also, is there a way to have push buttons added to the DSC board that would disarm and arm the alarm?
Hi. No only when it's armed for the light. Armed yes but not disarmed.
@@JasonTech cool. Can you provide some direction on how to arm the arm via a wired push button? It makes sense that disarming would not be allowed
Question: Why don't you use EVL-4CG. The app is free and you can arm and disarm from anywhere and get text alerts.
@@JasonTech I bought the Envisalink 3 a few years back and did not like the web interface.
Good afternoon sir,
The link you send me is not opening
It's a PDF on PGMs. Try again www.alarmhow.net/manuals/DSC/Intrusion%20Panels//PC1832/Application%20Notes/v4.2%20PGMs.pdf