Out of interest, did you have any difficulty (or require more force) with closing the hood once you had fitted this? It seems like the rubber moulding from around the main intake section presses hard up against the hood it is being closed. I definitely can't drop it from 2-3 inches anymore to close it..
Looking at @accordingtojoel’s video on the PRL inlet pipe it seems its possible. GruppeM/Blitz only needs the hard factory plastic intake tube for it to work 😉
Not sure about that red they used looks way too bright for me. If I had that intake I would have wrapped over the red in some black gloss or gloss carbonfiber.
![[VLOG]Honda Civic Type R FL5 Install Gruppe M Air Intake Best Engine Bay Look #fl5 #intake #gruppem](http://i.ytimg.com/vi/cIYqgazRIUM/mqdefault.jpg)
![[VLOG]Honda Civic Type R FL5 Install Gruppe M Air Intake Best Engine Bay Look #fl5 #intake #gruppem](/img/tr.png)
Fancy and clean, need it 🔥 great video
Thank you 🙏
Looks beautiful, congrats
Thank you 🙏
Love the sound man! Did you gain any horse power? I love it!
Sounds great, car pulls well so I assume it gained HP.
Do you have a link where I can buy it from? The link in your description takes me to the manual tho. 😎😎
@@theeaviatordreamer I bought it direct from Japan from Blitz. RHD or Nengun might be able to help?
@@Hattrk85 thank you
Thanks for the video ........ super appreciated ...... ;-)
No worries, thanks for watching 😇
Out of interest, did you have any difficulty (or require more force) with closing the hood once you had fitted this? It seems like the rubber moulding from around the main intake section presses hard up against the hood it is being closed. I definitely can't drop it from 2-3 inches anymore to close it..
Yes, for the initial few times it needed some force. But it’s fine now 😉
Very nice. Cost? Audio when car is moving?
Retail cost was about $1500 USD. I’ll try get some audio clips soon
Did you remove the battery terminal?
No
where is that secondary duct gonna suck air from?🤨
From the fender side
Nice one! Out of curiosity...have you had any error codes pop up? Idle control issues at all via MAF sensor?
No I haven’t had any codes or idling issues 😉
Are you tuned? I really want this but don't want to start down that rabbit hole
I recommend it though livens up the car quite a bit 👌
Great video once again. Is blitz same company as gruppeM? Apart from cone very similar
Yes technically the same intake just different filters. Blitz is a rebranded GruppeM without the K&N filter that GruppeM uses.
May i ask if the plastic strips of the air inlet will hold on the bonnet?
Sorry I don’t quite get what you’re asking. If you can dm me on instagram I can help further?
Looks better than eventuri intake
Its gorgeous 😉
is it hard to take out the filter and clean? or can you easily get to the filter without taking everything appart?
You’ll have to take the whole intake box out. Its not too bad since the FL5 has more space to play with than the FK8
@@Hattrk85 gotcha, thanks! I have a black fl5 and I always watch your videos to get inspiration on what mod to try next. Thanks for sharing with us
@@vellusk thank you so much for the feedback. It makes it worthwhile doing this as it does take up a lot of time
Do you think this is better than the aventuri one ? I’m between this two, still indecisive.
I had the Eventuri on the FK8. This time I wanted a JDM one. Other than that they’re pretty much personal preference 👌
The gains are pretty much the same ?
@@BennSides I think eventuri had more gains. Again its marginal and you can gain more with a bigger turbo 😂
Any codes being thrown or idle issues?
No codes or idle issues thus far, it has been solid 👌
Were is the link to get it the ones in bio are just install pdf
You can possibly get them from RHD Japan or Nengun
Can this fit with the prl inlet piping?
Looking at @accordingtojoel’s video on the PRL inlet pipe it seems its possible. GruppeM/Blitz only needs the hard factory plastic intake tube for it to work 😉
Do you have exhaust ?
Yes, Kakimoto 👉 ua-cam.com/video/3l7I8s2ztCU/v-deo.htmlsi=8YskRXhC1ZxYS3K3
It looks nice 👌 I'll give them that, but honestly think 🤔 for the price how much better is it then stock? If you wonder not much maybe 3% 😉
Thats at retail, I haven’t paid retail 😉
not even its forced induction . . . zero performance
Looks like it’s designed in Italy for a Ferrari 👍🏻👌🏻🍷
Grazie mille 😉
Not sure about that red they used looks way too bright for me. If I had that intake I would have wrapped over the red in some black gloss or gloss carbonfiber.
That was my first thoughts as well! But I just got used to it after awhile 😂
@@Hattrk85 good minds think alike. I wrap for a living so I always have extra vinyl lying around the house. But other than that it looks good 👍
@@Jdm_fl5 I wish I have your skills, I’d have done a video wrapping the piece as well 😉
It’s came from GruppeM 😂
Yep sure did
This Intake will only set you back 1.8k
USD?
@@Hattrk85 yes
Damn, that's freaking expensive for intake!
$$$?
Many $$$$$$$$
Any driving improvements