I had the same reactions when I drove mine for the first time wish I could experience that again for the first time. I’m glad you got it going enjoy it!!
Your reaction is priceless man! I have a 03 Sierra with a turbo lq4 and t56 swap. I blew the engine and I’m rebuilding it with a tsp 408 stroker kit. I can’t freaking wait to drive it again
For that size turbo,hopefully you did the -12 drain to oil pan. I used the -10 in the huron kit and it wasn't enough drain back for my 80mm. I have v4 t6 kit from huron. I was smelling oil burning due to not having the proper drain size and was backing up. Just an FYI
Awesome truck dude, I found a stock 54k mile 4.8 2005 chevy silverado 1500 I think I am going to buy and turbo it, the body is super clean with zero rust. What wheel setup is that? Those are sick.
Man, thats a sweet setup, good lookin truck man! What size motor? I'm just finishing my 1st turbo build in my 99 Camaro. I built a healthy 408 Mike Lough did his magic on the block and rotating assy., as well as his oil mod. I've got a FI 91/102 T4 that's going to go on it, fab 9", TH400, super clean 44k mile car. What'd yall do for exhaust? Three truck sounds nasty as hell man! I really wanted to run dual exhaust, split it at the turbo and try to squeeze it thru the k member. I know it'll fit on the d/s, but idk about the other... or ill do a single 4". It will have a exhaust with a muffler and will never have fender exits!lol I can't wait to get it running! It's been a long time coming man! I'm a anti roll bar, some fluids, a drive shsft... I'm sure a couple other small things, but I'm there with it! Your truck sounds nasty as hell man! What cam is in it? I ended up with a cam spec'd by Cam Motion, to help keep my backpressue down as the turbo is still a T4, but it's all t6 aside from that.
Any car I had a stall in i plumbed it to the external cooler and back, skipped the radiator. Hang where it has air or even make a dam. If I ran it in the rad the coolant would heat some when converter was slipping and both took more time to get temps down.
I want it the fluid colder than that! Around 70’s here it’ll still be 160-170. Could be the lines I have. Just some more research on it and some things to try so I can get the temp down
I am looking to lower my 2000 GMC 1500 and wanted to know what drop kit you used and how much of a drop in the front and rear. Trying to budget out my build. Bad ass cam!
Love the content, im installing the huron speed t6 set up in a 4th gen camaro atm. If love to get the same kit like yours for my 04 AWD Escalade. Who are you using for remote tuner? The 4th gen is on a holley, i have someone for that but i would need someone for the escalade. Some tuner recommendations for the central florida area would be cool if possible
😂😂😂 bro I know your neighbors be mad as hell when you get ready to leave for work 😂😂😂 looks like you get ready to leave around the time I do 4:30 am the only reason I haven’t went all in on my truck because mine is a daily driver so for five days straight that’s all they will hear every morning 😂😂😂😂 my truck going to be on flat 😂😂😂I already have dual Flowmaster
Question for you, what did you have to change to keep the A/C? Looks like longer lines or something, where did you get them? I have an on3 turbo kit coming at the end of the month and definitely need A/C here in Vegas! Looks and sounds great man!
I dont know who else makes it but from Huron Speed it routes the accumulator away from the exhaust and add some length to the line, it’s tight but so far seems to work!
Funny story! Bought the truck with that headliner about 6 ish years ago. At first I HATED it but then I stopped noticing it. So far I did everything else but change the headliner 😂
It’s not! I know where it’s at and it’s after the o2 sensors. After the turbo and everything. Just a down pipe piece that I can’t get to seal all the way
I had the same reactions when I drove mine for the first time wish I could experience that again for the first time. I’m glad you got it going enjoy it!!
Dude I was so pumped and still am! Love it so far
That's what it's all about! Fk yeah 🤘
Time to turn up the power then
@@Thaggard_is300 I said for the first time. I still enjoy it lol.
Wish I could enjoy this 😢
by far the best chopping LS i have ever heard
Your Neighbors must love you i know my neighbors love my lsx cammed 😂
Your reaction is priceless man!
I have a 03 Sierra with a turbo lq4 and t56 swap. I blew the engine and I’m rebuilding it with a tsp 408 stroker kit. I can’t freaking wait to drive it again
I’m glad to see this beast up and running💪🏼
She’s ripping and it feels great!
That thing is an absolute beast!!
Thank you!
I love how happy and excited you are lol
5:09 is the most glorious alarm clock.
This has motivated me to go ahead and build a truck!!!
180 degrees on a 4l80 after hard pulls and normal road driving is perfect! Parasitic loss becomes less with a warm trans.
I've got a 5.3 7875 I'm building the last 5 yrs can't wait to drive it again after all this time
Badass truck homie!! Chevrolet all day!!!🇺🇲🇺🇲💪💪
That’s what I’m sayin!!!!
sounds sooooo good sheeeesh!! panda is boosted and gf approved
Luckily I have that boost controller so I can just turn it down and let her go drive it
Bro “ ah did you hear it?” I felt that it my soul.
Sounds good man ive got a 99 looks like yours ,great trucks
All the faces he makes 😂😂 me when I’m almost done with a build 😂😂😂😂
Should mount the cooler near the spare tire on a angle
love the channel, keep it up brother!
For that size turbo,hopefully you did the -12 drain to oil pan. I used the -10 in the huron kit and it wasn't enough drain back for my 80mm. I have v4 t6 kit from huron. I was smelling oil burning due to not having the proper drain size and was backing up. Just an FYI
I used a -10! But so far I haven’t smelt any oil yet, I do have an oil leak on the pan somewhere. Tracking that down!
How do you have the crankcase vented?
Awesome truck dude, I found a stock 54k mile 4.8 2005 chevy silverado 1500 I think I am going to buy and turbo it, the body is super clean with zero rust. What wheel setup is that? Those are sick.
I have a 2001 single cab. Maybe it'll look that good one day. And have a LS in it. Just a 4.3 for now.
Don’t wait too long start getting little pieces here and there
Fixing to buy a 2001 totaled Tahoe to get the swap started
Looks great
Man, thats a sweet setup, good lookin truck man! What size motor? I'm just finishing my 1st turbo build in my 99 Camaro. I built a healthy 408 Mike Lough did his magic on the block and rotating assy., as well as his oil mod. I've got a FI 91/102 T4 that's going to go on it, fab 9", TH400, super clean 44k mile car.
What'd yall do for exhaust? Three truck sounds nasty as hell man! I really wanted to run dual exhaust, split it at the turbo and try to squeeze it thru the k member. I know it'll fit on the d/s, but idk about the other... or ill do a single 4". It will have a exhaust with a muffler and will never have fender exits!lol I can't wait to get it running! It's been a long time coming man! I'm a anti roll bar, some fluids, a drive shsft... I'm sure a couple other small things, but I'm there with it!
Your truck sounds nasty as hell man! What cam is in it? I ended up with a cam spec'd by Cam Motion, to help keep my backpressue down as the turbo is still a T4, but it's all t6 aside from that.
That's one Bad ass truck
Truck is awesome
Thank you!
Elite tuning is one of the best
sounds great 🔥
Any car I had a stall in i plumbed it to the external cooler and back, skipped the radiator. Hang where it has air or even make a dam. If I ran it in the rad the coolant would heat some when converter was slipping and both took more time to get temps down.
I have the same trans cooler and my 4l80e runs about 170-180 in the Texas heat with fan off and fan on stays just below 170. No issues
I want it the fluid colder than that! Around 70’s here it’ll still be 160-170. Could be the lines I have. Just some more research on it and some things to try so I can get the temp down
Where did you get the blue lights for speedometer?
Looks good.
I like that.
Cool build man...
That area looks like Port Orange Florida...
awesome man! where is this, port saint lucie?
I am looking to lower my 2000 GMC 1500 and wanted to know what drop kit you used and how much of a drop in the front and rear. Trying to budget out my build. Bad ass cam!
Bad ass truck man I like the wheel set up if you don’t mind what are the specs on the wheels and tires
How are you mounting your harness without a cage?
truck is a beast brotha! we have to meet up for a cars and coffee one day
Love the content, im installing the huron speed t6 set up in a 4th gen camaro atm. If love to get the same kit like yours for my 04 AWD Escalade. Who are you using for remote tuner? The 4th gen is on a holley, i have someone for that but i would need someone for the escalade. Some tuner recommendations for the central florida area would be cool if possible
yeah I'm using Elite Tuning on a stock computer! they may also tune on the Holley system !
Can we get a sound system video on the Silverado
truck looks good and sounds good / what size tires are you running in the back and front also thank you for your time
Rears are 295/65/15 and fronts I think are 245/45/20
Do you do ride alongs for your viewers!?
Sure do! Come on by I’ll let you drive it!
😂😂😂 bro I know your neighbors be mad as hell when you get ready to leave for work 😂😂😂 looks like you get ready to leave around the time I do 4:30 am the only reason I haven’t went all in on my truck because mine is a daily driver so for five days straight that’s all they will hear every morning 😂😂😂😂 my truck going to be on flat 😂😂😂I already have dual Flowmaster
Hey buddy are you planning to go to Street Car Takeover in Bradenton in a couple weeks? Would be cool to see this thing make a pass!
Question for you, what did you have to change to keep the A/C? Looks like longer lines or something, where did you get them? I have an on3 turbo kit coming at the end of the month and definitely need A/C here in Vegas! Looks and sounds great man!
I dont know who else makes it but from Huron Speed it routes the accumulator away from the exhaust and add some length to the line, it’s tight but so far seems to work!
Rear wheel set up and specs?
14:40 where is the poosie magnet?
Thing is beautiful but whats up with the headliner 🦓 🤔
Funny story! Bought the truck with that headliner about 6 ish years ago. At first I HATED it but then I stopped noticing it. So far I did everything else but change the headliner 😂
Hey bro what rear brake setup did you use to run them if I can get some info
The 1320 brake 15” conversion!
Where & who tuned your truck, i have a 2014 6.0 with the ls3 heads & truck Norris cam I need a good tune
Why would it shut off at stop lights? My built 6.0 does the same at times and going in reverse.
In the tune, something needs to be updated, it shouldn’t do it. New tuner and tune haven’t had an issue
@@SiskBuilt awesome. I appreciate it bro. Mines in the shop now getting a high ram intake and Stage 3 btr cam. Can’t wait! Love the truck man
@@S0T210 that’s what’s up! I need that holley high ram but I don’t wanna spend money right now 😂
@@SiskBuilt after that big turbo, i don’t blame you 🤣
What cam do you have in your truck? It's nasty
Nice truck, whats your tire specs?
She sounds mean!!!
Thank you!!!!
I just got Bosch 210 injectors for my 6.0LS with 88mm turbo. Think that’s overkill?
Where are you getting the oil feed from if your running a oil cooler aswell?
There is a sandwich plate I’m getting. I’ll make a video on it!
What cam is that? Sounds mean af
It’s a NA Comp Cam. 235/243 duration!
Sisk? Are you on the Treasure Coast?
@@hooknbook911 yes sir!
@@SiskBuilt Would love to see 🐼 in person..makes me wanna build my '07 silvy.
Whats the wheel and tire specs?
What wheel and tire setup are you running? And did you have to do anything to make it fit?
Those are bogarts ,look for bogarts for silverado
Literally bolted right on!
What bed cover is that? I've searched and can't seem to find a low profile like that one
It’s a eBay special from about 6 years ago!
are you running stock driveshaft?
what kind of wheels you got on the back wanna order some for my 1500
They are Bogart racing wheels!
hows the brakes / vacuum with this cam choice?
@@RSF98 brakes work extremely well!
Do u have drop spindle son the front ?
what PC are you using for HP tuners?
What cam are you using
Is this a 5/7 drop?
Hopefully that exhaust leak is not in a place that affects the tune🤔
It’s not! I know where it’s at and it’s after the o2 sensors. After the turbo and everything. Just a down pipe piece that I can’t get to seal all the way
I like how my pistons are flat top and yours are dished and yet mine are -5cc and yours are -3
are those specs for the pistons right?
@@jacobvanhalteren7452 i think mine were dished with valve reliefs! The -3cc dish!
What do you do for work brother?
I’m a planner for the county!
What tire size you running
wheel and tire specs ?
What’s the rwhp
What tire size
still 3.90 gears?
Yup! Still the same gears!
What size turbo ?
80/96!
@@SiskBuilt Nice!! I’m gonna upgrade to a bw 72 mm turb
0% on the boost controller is equal to waste gate, just an fyi
I currently have a 8 pound spring in there, but 0% on the controller is about 4 psi!
Is that headliner wrapped in real zebra skin?
Did you say the driveshaft exploded lol.
If it did hahah I went to a place in town and was joking if it didn’t work
@@SiskBuilt 😂 I guess I missed that part.
Whats the hp?
Atleast 300! Hahah
Wapoit ioapot boitaso capstoneoit wiopuoitpouast
Wreck it, you won't
Trying not to 😂😂😂😂
Headliner proves he gay
You could have at least picked a nice looking Silverado, not the ugliest of them all, the cat eyed version.
Dude , fix the volume on your video.
What wheel and tire setup are you running? And did you have to do anything to make it fit?
The rears are an off the shelf 15x10 by bogart and the fronts are a different offset to clear the 2020 front brakes!
Are the fronts 17s or 18s? I have 2020 brakes on mine and some 17s fit and some don't it's super weird. @@SiskBuilt