Thank you for your video. Learned a lot controlling dc, stepper and servo motor. Your the only UA-camr channel that’s clearly explained the Arduino motor shield all the rest are very complicated. Thank you again, now I’ll subscribed to your channel
Hi ,thank you very much for the video,I have a project but I need to run 2 stepper motores with 2 servo motores and 2 dc motores in one arduino ,so I need to add one stepper and one servo to the configuration you've done in the video ,is that possible and how ,thanks
Hi sir! please provide me code to run servo motor and dc motor at the same time as you shown four (servo motor, 2dc motor, stepper motor)different motor at the same time(15:56 in this video)
thank you sir very much for your explanation, I have to plan build a sticker cutter using l293 d driver using nena stepper motor , can you help me to program how to make pls... help me
Excellent video, it helps me a lot. Just one more question, when you directly supply power to the arduino motor shield, what is the voltage range? thanks
What about controlling motors with buttons? With the shield, I'm seeing a problem with adding buttons to this set up since all the pins are occupied with the motor shield.
I have connected 12v 1amp power supply to motorshield only, then suddenly both aurdino and motorshield get fried. Can i use 12v 1 amp for motorshield ?
@@UtGoTechHere I am using 12volt 2 DC motor and 1 servo motor. So I am planning to give power separately, 9volt for motor shield and 6volt for uno board. This board need to be working for 8hrs continuously. So that is there any issues with the board and powersupply that I am planning to give?
@@UtGoTechor is it possible to use 9volt in dcjack of aurdino to work both aurdino and shield simultaneously? Which is the better option? Could you please suggest me😊
If you are going to operate two 12 volt motors continuously then I suggest you to check current taken by those motors also as L293D motor driver can provide 600mA per channel. As per your case it looks like it will heat up the IC's and boards and damage it. As per your case I suggest you to look for other high power motor drivers.
How to control one dc motor 12v 90W MAX and one stepper motor like yours i want to make a car. The stepper motor will make the car move left right and dc motor to help it move forward how to control them using WiFi module ESP12E DEVKIT V2
@@UtGoTech I think so, I tried using jumper to power the motors at the same time.(not working) Also tried to use 6V battery to power it up but not working as well. I measure the voltage of the four connections and none of them have voltage. Then I guess my motor shield is broken so I get a new one from amazon, not working still.
Check the polarity of battery. If the polarity of the battery is correct then check the voltage of the battery in the terminal where you have connected.
For using all motor and sensor you have to focus on timing. Using proper timing you can control all the sensors and motors, which will look like you are controlling it simultaneously.
Thank you for your video. Learned a lot controlling dc, stepper and servo motor. Your the only UA-camr channel that’s clearly explained the Arduino motor shield all the rest are very complicated. Thank you again, now I’ll subscribed to your channel
Thank You Most Welcome...
Very nice video for someone who needs to learn how to use the Motor Shield.
Thanks 👍
i am using this to make a drone.So,how can i increase the speed very high?(its brushed motors with 50000 rpm) pls say fast .
This motor driver can drive a drone motor
hi I am having problem with my motor running without the power going through arduino
Can you explain little bit more
Hi ,thank you very much for the video,I have a project but I need to run 2 stepper motores with 2 servo motores and 2 dc motores in one arduino ,so I need to add one stepper and one servo to the configuration you've done in the video ,is that possible and how ,thanks
No. It's not possible with Arduino Motor Shield.
@@UtGoTech OK, do I have to buy 2 arduinos to do it? Thanks
There are different ways to achieve it.
Yes you can do it with two Arduino board.
@@UtGoTech thanks
Welcome
Sir we have to connect two servos in a single motor driver shield and we have connected hc 05 to that servo pins so sir how can we solve it?
You can use pins from A0 to A5 to communicate with the bluetooth module and use 2 servo motors
How we can use dc motor in cnc ? Plz without step motor i want the same list 4 dc motor and l293 driver ardouin
CNC requires accurate positioning. That's why it seems difficult to achieve using simple DC motors.
bro if i use 12v external to motor drive the. will all motor get 12v equally ???? i will use ac to dc adapter of 12 v so parellel it will work?
Yes
Hi sir! please provide me code to run servo motor and dc motor at the same time as you shown four (servo motor, 2dc motor, stepper motor)different motor at the same time(15:56 in this video)
Same to you
You have to modify the code according to your need.
@@UtGoTech Hi, can you show how to do that ??? Or can you share the code please ??
What is your requirements. Explain it clearly.
@@UtGoTechI'd like to just see the code. Because i don't understand how to conect code servo and dc motor
thank you sir very much for your explanation, I have to plan build a sticker cutter using l293 d driver using nena stepper motor , can you help me to program how to make pls... help me
Welcome.
Excellent video, it helps me a lot. Just one more question, when you directly supply power to the arduino motor shield, what is the voltage range? thanks
You can give 6 volts to 12 volts. But I suggest you use it up to 9 volts.
Can we run neema 23 steeper in place of CD-ROM drive steeper
No. Neema 23 motor required much more current than L293D motor driver can provide.
we can combine control 4 dc gear motor and 2 servo motor on l293D motor drive.
Yes
Thank you, this was so great.
Glad it was helpful!
What about controlling motors with buttons? With the shield, I'm seeing a problem with adding buttons to this set up since all the pins are occupied with the motor shield.
No pin 2 and all the analog pins are free. They can be used to take button feedbacks.
@@UtGoTech how would you plug them in? Would you just use jumper wires instead of plugging the shield in directly?
@@UtGoTech I didn't even notice the extra spaces leading to no where on the shield! You are 100% right! Thanks @Ut Go!
Welcome
I have plugged the shield directly which is shown in starting of the video.
Can we connect 4 micro dc geared motor at same
Yes you can
Please make solar flower opening & closing & opening 3 servo drive motor with LDR SENSOR. PLEASE HOW TO CODING.
Share details. What project do you want to make?
Solar flower project.
Please share some sample pictures with us through Instagram.
Very good video 👌
Your explanation is very clear and easy to understand 👍
Can we run bldc motor using this?
No, this motor driver cannot drive BLDC motor.
I have connected 12v 1amp power supply to motorshield only, then suddenly both aurdino and motorshield get fried. Can i use 12v 1 amp for motorshield ?
Running too long on 12 Volt may fry you motor shield. You have to select voltage between 6 Volts to 9 Volts.
@@UtGoTechHere I am using 12volt 2 DC motor and 1 servo motor. So I am planning to give power separately, 9volt for motor shield and 6volt for uno board. This board need to be working for 8hrs continuously.
So that is there any issues with the board and powersupply that I am planning to give?
@@UtGoTechor is it possible to use 9volt in dcjack of aurdino to work both aurdino and shield simultaneously? Which is the better option? Could you please suggest me😊
In your case I suggest using a separate power supply.
If you are going to operate two 12 volt motors continuously then I suggest you to check current taken by those motors also as L293D motor driver can provide 600mA per channel. As per your case it looks like it will heat up the IC's and boards and damage it. As per your case I suggest you to look for other high power motor drivers.
Is there away to control all that with a pontiometer and a push button?
Yes
How much power did you supply for running all motors at the same time? (@ timestamp 1:12)
6 volt
Thank you Sir, I have a question how it can be done if i want to control multiple motors independently?
Just code as per your requirement
How to control one dc motor 12v 90W MAX and one stepper motor like yours i want to make a car. The stepper motor will make the car move left right and dc motor to help it move forward how to control them using WiFi module ESP12E DEVKIT V2
You have to search for high power motor driver as you are going to use 90 watt motor.
Does the motors get the same amount of power you supply the board with?
Partially true
@@UtGoTech what’s wrong then?
Are you talking about power or voltage ?
@@UtGoTech voltage
Average Voltage changes according to the speed of motor.
Hi, I am so confused why my motor shield doesn't run. I used the exact the same code as yours.
Are you using the correct power supply?
@@UtGoTech I think so, I tried using jumper to power the motors at the same time.(not working) Also tried to use 6V battery to power it up but not working as well. I measure the voltage of the four connections and none of them have voltage. Then I guess my motor shield is broken so I get a new one from amazon, not working still.
how to code motor DC and servo motor at the same time
Code using the functions shown in the video. Just make sure to include Adafruit Motor Shield Library.
When I connect my battery with the driver shield then the green light do not glow. Can anyone help me plz?
Check the polarity of battery. If the polarity of the battery is correct then check the voltage of the battery in the terminal where you have connected.
Hey can you make a tutorial on how to program the stepper motor using the motor shield
I have already made it.
Link?
ua-cam.com/video/vooJEyco1J4/v-deo.html
Can we control this with bluetooth
Yes you can
How??
@@UtGoTech can I control servo motor like steering for rc car
Yes, you have to code according to your need.
@@UtGoTech ok thank you 😍😍
how much power should I give to the motor shield? and send a link for your screwdrivers to buy
You should give power according to the motor attached to the motor shield.
I am using Iron Spider (45 in 1 Tool Kit)
www.amazon.com/Precision-Screwdriver-Tamperproof-Security-Extension/dp/B00SXF68IW
please tell why dc motor doesnt drive, it's only beeping. i use 9 v battery and did everything from the video
Use lithium ion batteries as shown in the video.
@@UtGoTech thank you very much, now it's works, I just put 18650 battery as you mentioned
Welcome
I really like your content and your videos keep going ♥️🔥
Thanks 👍
What is the library name?
Adafruit Motor Shield V1 Library
@UtGoTech thank you so much
Thank you so much @@UtGoTech
Welcome 👍
Nice buddy...
Thanks
how to conect to servos
Watch full video.
Bro how could run all in. One code
Didn't understand your query
Sensors bro how to connect with this
Which sensor you want to connect ?
@@UtGoTech ir and ultrasounic please
Thank you
Welcome👍
I need ir and ultrasounic please bro put it
For using all motor and sensor you have to focus on timing. Using proper timing you can control all the sensors and motors, which will look like you are controlling it simultaneously.
Code?
You can find example sketch given with the library
please can do that use python and how
I think Arduino support C programming only
Can we connect 4 micro dc geared motor at same
Yes you can.
how to conect to 2 servos
Watch full video and you will know