Oof when you said 600hp I was like "Oh hell yeah!" Moser axles, quick performance gears, posi, diff cover, stronger caps. Gonna start saving to upgrade my 7.5
@@Mr_getinthere hey what factory posi rear end will fit under my 79 caprice with little to no modifications. What car can i get one out of preferably disc set up
Yeah for my 95 camaro, I swapped the whole rear from a 98-02 camaro. The only problem is I accidentally picked up a traction controlled unit so I had to have a hole drilled into the top of the pumpkin for my ABS sensor along with transferring over the brake lines. Otherwise it was an easy swap. I got a zexel Torsen lsd and upgraded 3.42 gears out of this as mentioned. In addition I rebuilt the rear end with my grandfather with new timken bearings, upgrades TA performance diff cover, Moser axles (cuz one axle was shot from bad wheel bearing), and bearing cap studs. I later bought GM 4.10 gears off eBay, but have yet to install. I agree GM gears are the most quiet, but not as strong.
I appreciate your videos, I'm on a tight budget and this helps. I have both a 1978 Buick regal Ttype all original and a 1998 z28. 8 have plenty of spare parts for my camaro, I think I will drop in the extra posi unit from my camaro into my Regal.👍
Great info been following your build for a while now but would like to know specifics like pinion depth and preload, shimm sizes ,and torque specs .for us that need information spoon feed
I just got a '80 Monte Carlo. I'm gonna put an LT1 out of a 96 Roadmaster in it. I'm broke and just lookin for a fun burnout machine/cruiser. Anything I can get from a junkyard is right up my alley. Thanks for the info
All the 5spd f-bods are 3series w/3.42 gears. The auto options 3.23 gears w/3 series. The 2 series are the 3.08 and lower.(weak) Factory grs are 2-cut, Need more back lash. Run pattern is centered. I put in 5-cut 3.55's and set 0.004" Backlash. Just took it out and it's great.
I finally got me one I believe it’s 342 gearing off a 98 z28 has the abs ring on it my thing is how do I know to go with ether thick 373 gearing or thin love your content man 💪💪
Man bro i love the info you have such a break through, i was currious as to axles because these folks out here selling the axles dont know crap anyway will these work in my 83 camino ive also got a torsen zexel M-GRIP ALLOY AXLE SHAFT KIT 1541H - COMPLETE - 28 SPLINE - 8.2" - 5 X 4.75
MR_getinthere, now when I do my rear-end like u have here, should I stick with the same 3:42 gear size that would be in there when I pull it from the comaro or should I go with the same 3:73 gear size that came in the stock g-body rear end? I apologize if this sounds stupid but I'm real green when it comes to rear ends other than knowing how to put them in or bolt them back up. Granny taught me that the dumb question is the one u don't ask so I'm asking man.
What would you use from the umi rom the rear housing bushing? The rotor joint or the poly. I already have rotor for the arms. Should I use poly to get a good ride or the roto? It’s not a track car just riding around and burn outs
Will this also work for the jdm 7.5”? Was used in everything from the Toyota pickups-Isuzu pickups, the biggest difference I’ve noticed from research is the carrier comes out the front instead of the rear. I’m LS swapping a 92 Isuzu pup an everyone tells me they use a 7.5” carrier and locker but trying to confirm before I spend $300-700 on a whole kit
How many bottles of gear oil do you need to fill it back up have the same setup put a hundred miles on it opened it back up left side axle when I pulled and had no fluid running down the tub right side was good put like two and a half bottles in it I don't think that was enough?
He is correct . A Yukon 7.62 posi 28 spline 377 dollars.. Moser axels for 1987 grand national 319 dollars . Motive bearing kit 115 dollars. (Fits 7.5 , 7 5/8 , 8.5.) 8.5 g body axels fit 7 5/8 as well. About 150 for ring and pinion. Around 1200 hundred bucks in parts. And 150 to 300 to set it up. As of 4 July 2023 you’re looking at 1350-1500 bucks total. And it will definitely hold 500 hp.
How tf do you remove the little keeper bolt mine will not come loose. I’ve gotten impacts and all on it and it will not budge. Never had that much trouble with one.
Everyone on here is GM, Chevy, but does this info transfer over to a Ford 7.5 rear end? Because your video caught my eye because I want to beef up my 7.5, it is also 28 spline, so will the Zexel fit a Ford?
Very simple my guy , just push the axles in then you will see the slot where the clips go in at pull the axle back out ,and that will lock the clip in and just replace the center block that will hold the axles so the clip won't fall out
Damn bruh I wish you would answer some questions it would get your subs up too. Jegs sells a rear end with the Moser 28 spline axle for about 1k would this be the same? I live in NJ most mechanics that work on old school cars are white and will over charge and if it's a older mechanic who black and race he does not want your car faster than his.
Ive seen it done on jmalcoms channel with his cutlass. that has a 355 with a wieand 142 supercharger. makes about 400 to the wheels. i would NOT do a transbrake though. thats pushing it
I like how u think...fuck a 9 inch or an 8.8...i dont feel its necessary tbh...i just rebuilt my gm 10 bolt in my 94 firebird formula ..how many miles u think ill get outta the clutches in it? Its a ebay 180 special lol
Aye bro I'm starting to finally build my SS after stocking up parts for the last 14 years lol. But my question is my housing, axles, and locker have some rust......a littler more than this one, but will it mix with the gear oil and damage anything? I've spend the last two days cleaning it off.
I know the ring and pinion have to match but is the camaro pinion the right size for monte Carlo rear end because im going to buy 3.73 gears and i dont know i need to buy gears for a 84 monte Carlo or a 2000 Camaro ?
The gear have to match the posi some posi take a ticker gear some dont ..this one was a 3 carrier posi so its not a thick gear ..get with quick performance and send them a pic of your posi they will get you right
It a gu6 code
Thanks fam
Do you have any for sale
@@ygdoubledollaDSM not right now fam
I realize Im kinda off topic but do anyone know of a good site to stream newly released movies online?
@Crew Sawyer i would suggest flixzone. Just search on google for it =)
U not RUMBLING everything u say is BENEFICIAL to us that want to know more OG!! Definitely appreciate all ur content!
Thanks alot fam 💯
After I get my daily figured out I’m going to dig into my 7.5!!!!! Appreciate the info brother!
Oof when you said 600hp I was like "Oh hell yeah!" Moser axles, quick performance gears, posi, diff cover, stronger caps. Gonna start saving to upgrade my 7.5
Good informational video bra you're doing something alot of people don't. And that's breaking it down in depth.
Thanks alot i try too
@@Mr_getinthere hey what factory posi rear end will fit under my 79 caprice with little to no modifications. What car can i get one out of preferably disc set up
@@antoniotrotter150396-97ss
Yeah for my 95 camaro, I swapped the whole rear from a 98-02 camaro. The only problem is I accidentally picked up a traction controlled unit so I had to have a hole drilled into the top of the pumpkin for my ABS sensor along with transferring over the brake lines. Otherwise it was an easy swap. I got a zexel Torsen lsd and upgraded 3.42 gears out of this as mentioned. In addition I rebuilt the rear end with my grandfather with new timken bearings, upgrades TA performance diff cover, Moser axles (cuz one axle was shot from bad wheel bearing), and bearing cap studs. I later bought GM 4.10 gears off eBay, but have yet to install. I agree GM gears are the most quiet, but not as strong.
I appreciate your videos, I'm on a tight budget and this helps. I have both a 1978 Buick regal Ttype all original and a 1998 z28. 8 have plenty of spare parts for my camaro, I think I will drop in the extra posi unit from my camaro into my Regal.👍
Nice Bro, keep the tech tips coming, we need it.
Hit that thang boy 💪🏾💪🏾💪🏾. Good info everybody ain’t out to build a race car
How in the HELL did I just now find this unicorn channel. Definitely coming back here for the knowledge. Keep it up my G
Thanks fam ,hitt that subscribe button 🙏
Damn straight homie. Already over there 💯
Great info been following your build for a while now but would like to know specifics like pinion depth and preload, shimm sizes ,and torque specs .for us that need information spoon feed
Good video. I plan one doin my boxchevy like this. 💪🏾💪🏾
I'm loving your videos.
thanks
Thank u so much 🙏🙏
@@Mr_getinthere you have a lot of good videos im finding out
thanks.
I got the Detroit truetrac with the moser 28s. They look identical damn there
Great video man. Lots of info !!Pinion needs to be just a slight bit deeper just so you know to get it perfect 👌
I love this video. Very informative.
🙏🙏🙏
I just got a '80 Monte Carlo. I'm gonna put an LT1 out of a 96 Roadmaster in it. I'm broke and just lookin for a fun burnout machine/cruiser. Anything I can get from a junkyard is right up my alley. Thanks for the info
I just told you in the vid fam 🤦🏽♂️🤦🏽♂️ or just buy a new 26 spline posi
All the 5spd f-bods are 3series w/3.42 gears. The auto options 3.23 gears w/3 series. The 2 series are the 3.08 and lower.(weak) Factory grs are 2-cut, Need more back lash. Run pattern is centered. I put in 5-cut 3.55's and set 0.004" Backlash. Just took it out and it's great.
I got the 8.5 grand national rear end in my 84 cutlass But I’m gonna build a 7.5 this way for my lil bro thanks mr gitinthere.
👍always solid info
thx for the info mr_getinthere💪
I finally got me one I believe it’s 342 gearing off a 98 z28 has the abs ring on it my thing is how do I know to go with ether thick 373 gearing or thin love your content man 💪💪
Man bro i love the info you have such a break through, i was currious as to axles because these folks out here selling the axles dont know crap anyway will these work in my 83 camino ive also got a torsen zexel
M-GRIP ALLOY AXLE SHAFT KIT 1541H - COMPLETE - 28 SPLINE - 8.2" - 5 X 4.75
Send me 270 shippee i see you wat u need
MR_getinthere, now when I do my rear-end like u have here, should I stick with the same 3:42 gear size that would be in there when I pull it from the comaro or should I go with the same 3:73 gear size that came in the stock g-body rear end? I apologize if this sounds stupid but I'm real green when it comes to rear ends other than knowing how to put them in or bolt them back up. Granny taught me that the dumb question is the one u don't ask so I'm asking man.
What would you use from the umi rom the rear housing bushing? The rotor joint or the poly. I already have rotor for the arms. Should I use poly to get a good ride or the roto? It’s not a track car just riding around and burn outs
Will this also work for the jdm 7.5”? Was used in everything from the Toyota pickups-Isuzu pickups, the biggest difference I’ve noticed from research is the carrier comes out the front instead of the rear. I’m LS swapping a 92 Isuzu pup an everyone tells me they use a 7.5” carrier and locker but trying to confirm before I spend $300-700 on a whole kit
How many bottles of gear oil do you need to fill it back up have the same setup put a hundred miles on it opened it back up left side axle when I pulled and had no fluid running down the tub right side was good put like two and a half bottles in it I don't think that was enough?
Yessir 💪🏾
He is correct . A Yukon 7.62 posi 28 spline 377 dollars.. Moser axels for 1987 grand national 319 dollars . Motive bearing kit 115 dollars. (Fits 7.5 , 7 5/8 , 8.5.) 8.5 g body axels fit 7 5/8 as well. About 150 for ring and pinion. Around 1200 hundred bucks in parts. And 150 to 300 to set it up. As of 4 July 2023 you’re looking at 1350-1500 bucks total.
And it will definitely hold 500 hp.
You the GOAT
Thanks bro
Is there anything I need to know about series two and three ring and carrier? Thanks for all the help in the work you do.
They use different ring gear series 2 ring gear thicker then the series 3
I believe one series is thinner in order to accommodate the abs wheel
What do you order the bearing set for a g body or for the camaro?
What about the Pinion Yoke? Is it the factory GBody Pinion Yoke or the one off the Camaro? Or Does it matter??
How tf do you remove the little keeper bolt mine will not come loose. I’ve gotten impacts and all on it and it will not budge. Never had that much trouble with one.
What up I got torsen the axel too short I can’t put the c clip in might be a inch or two short what you think
Hey I’m lookin for 28 spline axles for my 76 Buick they bolt on can you help me out
Are the JEGS BRAND AXELS ANY GOOD ???
💯💯💪🏿👀
Can you still get the zexel torsen rear for gbody
Everyone on here is GM, Chevy, but does this info transfer over to a Ford 7.5 rear end? Because your video caught my eye because I want to beef up my 7.5, it is also 28 spline, so will the Zexel fit a Ford?
Idk fam that's a good question I'll find out and let you know
What gear and pinion is that ?
What you have too have for that posi unit if you have any
Hey I found a posi out a 91 typhoon 7.5 28 spline is that ok?
Do you have a set ready for a drop in
Well you're taking my language
Thank you for noticing us brotha we ain’t dogging it all the time but if you catch us at the car wash we might hit it
Lol @car wash 💪💪
@@Mr_getinthere I’m from Mississippi we still hang out at the car wash man 😎😎😎
@kanairsforte5298 I'm in Louisiana let me know if you need me
Sorry for asking on an old video.. could you possibly explain how to reinsert the c clips on the build in this video
Very simple my guy , just push the axles in then you will see the slot where the clips go in at pull the axle back out ,and that will lock the clip in and just replace the center block that will hold the axles so the clip won't fall out
That center block he mentioned is doing the same thing the cross pin you're used to in open or clutch type diff.
OP, did you get your RPOs down??
What's the best combo for usin all junkyard parts? I'm on a tight almost non-existent budget
🙄🤦🏽♂️🤦🏽♂️ i just told you in the vid
Damn bruh I wish you would answer some questions it would get your subs up too. Jegs sells a rear end with the Moser 28 spline axle for about 1k would this be the same? I live in NJ most mechanics that work on old school cars are white and will over charge and if it's a older mechanic who black and race he does not want your car faster than his.
It's rear end parts like posi , gears bearings it's a whole rebuild kit ??
If you post a link, that would help. Several different size 10 bolts can have 28 spline axles.
Bro do you recommend changing the ring and pinion gears as well? Or will your stock ones work if their still in good shape
U can , but I always change them rebuild kit and gears like 200 shipped
@@Mr_getinthere I have a 7.5 in my el camino, do you still build them?
I live in Louisiana.
@@thegrove17 yess
@@Mr_getinthere How can i get in touch with you? I only have facebook and email?
Will it not hold slicks at the track with a 475 hp 383?
Ive seen it done on jmalcoms channel with his cutlass. that has a 355 with a wieand 142 supercharger. makes about 400 to the wheels. i would NOT do a transbrake though. thats pushing it
I have a problem with mines, too tight and can't adjust backlash. Any solutions?
It's not right lol , back last can always be adjusted with different shims
Yep got mine but you didn't say have to upgrade the axel from 26 to 28 spline.
Yes you have to change the axles
Hey when u build that rear end do use a monte carlo pinion or a Camaro pinion ?
Pinion got to match the ring gear if u got 342 gears pinion got to match too
Will the 28 spline work on a B-body with 7.5 rear end?
Yess .fam 7.5 dont matter wat it's in long ass the axles match the posi
U said has to be gbody moser but 8.5 length or 7.5 being its 7.5 rear u confused me
What'd the name of that set up
I have the same rear end, do you have a video of taking the c clips out bc I’m haven a hard time can you send me a video thank you
Push them all the way in and rotate the casing. It’ll fall out
I like how u think...fuck a 9 inch or an 8.8...i dont feel its necessary tbh...i just rebuilt my gm 10 bolt in my 94 firebird formula ..how many miles u think ill get outta the clutches in it? Its a ebay 180 special lol
Can you do tha same thing with a 10 bolt 8.5 rear-end???
yeah and theyre stronger
I have a xbody would that rear end work for my 1978 buick Skylark
i think you have an 8.5 this would be a downgrade. you better check which rear end you have but i think x bodies have 8.5's
You made me laugh about the old man and the cookout comment
🤣🤣🤣🤣
That was good and true 🤷♂️👌👍
Mee too 😂
Does the torsen come with the 3;23 ratio in the 98-02 camaros
No 342
Aye bro I'm starting to finally build my SS after stocking up parts for the last 14 years lol. But my question is my housing, axles, and locker have some rust......a littler more than this one, but will it mix with the gear oil and damage anything? I've spend the last two days cleaning it off.
No it want just prepare to change the gear oil soon
what's up mr getinthere can a 2004 Chevy Blazer backing plate works for box Chevy
Yesss
@@Mr_getinthere thank you and I'm excited for your next new videos keep doing your thing
What the best way to fit 24 on front of gbody Cutlass, plus wat can I do bout front sway bar
New springs or if you got the cash coilovers
Umi sway bar
Or find a 85-88 IROC or trans am sw6 front sway bar is performance from gm I have one on my 85ss it works bro here has a video on the sway bar
@@youngsolja1779 what end links work with that iroc swaybar
gbody moor I used stock links drives like a foriegn
What axles do I need for a Box Chevy?
Bubble Rearend
Hey man...is there anyway i can get in touch to get help with my frame-off 85 Monte Carlo ss build...first timer doing frame off and i need some help
Wya ?? Getinthere.boys@gmail.com ..or hit me up on ig
How do I get in touch with you....what's your phone number
@@Mr_getinthere I need some help or a rear end ....where are you located.....and do you have a 7.5 ready?
How much would you sell one of those units for.... i search through 5 junkyards yesterday no luck
200 shipped
Need one for a 86 cutlass
Big bro I need that I got 83 el co 5.3 cam just getting in the game
Wya , just let me know
I’m doin this To my 85 ss do I get 28 moser 7.5 axel or 8.5 I have the 7.5 rear
Grand national had the 8.5
He said grand national axles
😅😂 7.5 Maaann
Good lord, did u leave any marking compound for anyone else?? Lol.
🤣🤣🤣🤣🤣🤣🤣😂😂😂😂😂😂😂
Np yeah 3.42 r gu6 3.73 is gt4 codes
I know the ring and pinion have to match but is the camaro pinion the right size for monte Carlo rear end because im going to buy 3.73 gears and i dont know i need to buy gears for a 84 monte Carlo or a 2000 Camaro ?
The gear have to match the posi some posi take a ticker gear some dont ..this one was a 3 carrier posi so its not a thick gear ..get with quick performance and send them a pic of your posi they will get you right
And yess the gears out the Camaro will fit in the mc
Cool thank you can because I'm fixing to go pick up a torque Zexal at the Salvage right now
Hey do you know what size that pinion nut is on the Camaro
@@jasonyi7300 1" 1/4
how can I contact so I can have u build me one. 87 elco 350 sbc 700r4 with 22inch rims
Where u located at ??
Will this set up work for a stock 5.3 LS in a 1987 MONTE CARLO LUXURY SPORT on 30 inches?
I got 26’s it pulls good but I’d get a 8.8 or a 9
Yes
901 Checking In
Thanks alot 💪🏾💯
305 checking in🔥that whole posi unit come out of a 98-02 camaro right?
💯💯Yep look for g80 on the door
@CrazyWhiteGuy lol right
I can't find one of these posi units to save my ass. Can you find them & how high are the axels?
I sell the axles for 300 shipped
@@Mr_getinthere can you find the torsen posi? Everything is dried up around here. That's not bad price on those axles, not bad at all.
Yo got a video of u redoing a rear end?
No ,it's not something average person can do without the right tools
@@Mr_getinthere I feel u
Bro were u at I'm in Mississippi
Louisiana
@@Mr_getinthere well damn I might see u around one day I'll Kno your voice
How much do those axles run?
300 from me
It was 260 for my moser axles, but that was back in 2012 or 2013 IIRC. I think back then was free shipping also…man have prices gone up!
Yo brother How much for a set of 28 spline axles
275 shipped
Do have cash app
They fit the g body with the 2001 camaro gears
With out modification
@@Mr_getinthere28 splined axles for a 85 s10. 7.5 need them!!!
V6 cars have the same posi?
Yep SOME THO
@@Mr_getinthere theres never any v8 cars why I asked. They'll have the same code I'm assuming? Might just have to get a mini spool
@@H00K-KING yes same code G80 .
@@Mr_getinthere word. You got a vid on what ac kit you used?
You got any for sale
No fam just Moser axles
Can you email me im trying to get my rear narrowed
Getinthere.boys@gmail.com
Wait u from Nola?
😎
@@Mr_getinthere bet, I'm near BR anyway to get in contact with you
@@b3nny534 u got Instagram??
@@Mr_getinthere yep think I found you on there
@@b3nny534 send me a dm..
"Ill be 1000hp club" lol that aint yo damn car 🤣🤣🤣🤣🤣 i couldn't help myself
🤣🤣🤣🖕🏽🖕🏽
🤣🤣🤣
Great video I just wish it was in English
I have a 81 Elco with a 427 small block. Should I keep the same rear end or should I change it
Depends on wat you doing with the car
@@Mr_getinthere it’s going to be my cruiser
@@steadymobbin6146 7.5 ftw
@@Mr_getinthere should I keep the gears that I have and just put posi