Kelvin, this was such a great video. Thank you so much for taking the time to make this! You have some phenomenal building skills. You've inspired me to want an FPV jet some day. You did this one PERFECT!
Talk to me, Goose! Freewing is producing really nice models. I never thought I would buy a Foam airplane until I laid eyes on this Freewing F16. Now I have two. I bought a spare to set up FPV. This video is going to help a bunch. Thanks for all this information. This was one of the coolest EDF FPV flights I've seen. Liked and Subscribed.
Thank you so much for making this video. I’ve been wanting to do this to one of my models for years but never could find a great, descriptive video going through everything.
Kelvin, what an incredible project. Your attention to detail sets an example to anyone interested in RC flying! For your landing mode with flaperons, are you only getting roll control from flaperons? was there any mixing with the elevons? Congratulations , you obviously put in an incredible amount of time into your projects.
Clean with microfiber and windex or ammonia , then spray again after wiping just to clear off any impurities , leave the spray on there and dip it in quickshine floor shine . Let it sit in a seal container to avoid any fibers and dust settling on it while it cures . Leave it for 48 hours and re dip it until you get the result you want
@RyanQuellet thanks Ryan. I use chemical guys ultra fine car polish. I polish about 3-4 times with a microfiber. Then I follow with a automotive ceramic coat. I do this process to both the inside and out side of canopy.
Are you using a voltage regulator to the fan because the power is coming directly from the battery? Can you connect it to the 5v voltage supply on the flight control board or an RC type BEC?
@stephanbrown6724 yes. I'm going straight to the battery with a 12v fan and regulator. I didn't use a supply off the board to prevent any chance of browning out the system. I wasnt sure if 12v/9v rail rail on the fc would handle the load of a fan and the o3 air unit
Nice setup. I have a similar setup but my fpv gauge micro controller is acting weird. Can you send me the ino files from the cockpit gauge microcontroller?
@DizzyRC directly from battery to esc. Flight controller power is split off the esc power input cable from battery. I do not run power through the flight controller to esc. As it is rated for 150amps and the esc fan combo pulls close to 130amps i felt it was to close for comfort. I use a seperat hall effect current sensor to get current data to the fc.
Kelvin, this was such a great video. Thank you so much for taking the time to make this! You have some phenomenal building skills. You've inspired me to want an FPV jet some day. You did this one PERFECT!
@@Mach3RC thanks 😊
@@kwboost BTW, im a car guy too. Love to see it! haha
Mate that’s amazing!!! The F-16 is my fav jet and that’s probably cause of the repeated sessions of iron eagle as a kid
Love your setup
Your builds are so meticulous & clean! I’m hoping to build a fpv F22 in the near future.
Talk to me, Goose! Freewing is producing really nice models. I never thought I would buy a Foam airplane until I laid eyes on this Freewing F16. Now I have two. I bought a spare to set up FPV. This video is going to help a bunch. Thanks for all this information. This was one of the coolest EDF FPV flights I've seen. Liked and Subscribed.
@@FarmerFpv thank you. Check the description for links to the 3d printed parts if you need them.
Dude this is so frigging cool!
Thank you so much for making this video. I’ve been wanting to do this to one of my models for years but never could find a great, descriptive video going through everything.
duuuude this is sick! 🤘
Good work on that jet . The perfection is goals !
Awesome vid that flight was great. Thanks for sharing. Hope to see more
This is exactly what I'm trying to get into. This is great content for how to get into the RC FPV hobby! Thank you!
Very informative, very clean build I’m impressed with the outcome
I expect nothing less from you. Good to see ya even if it was just on a video.
@deadringerfpv6412 thanks bro.....been too long.
Wow thank you for this video I want to move to a fc now . Can’t wait to see your next projects .
Looking good Kelvin!
Talking points on point
❤😊
Kelvin, what an incredible project. Your attention to detail sets an example to anyone interested in RC flying!
For your landing mode with flaperons, are you only getting roll control from flaperons? was there any mixing with the elevons?
Congratulations , you obviously put in an incredible amount of time into your projects.
i'm super impressed
Great Video!!! 👏💯🔥🔥🔥
yooo thats a big one :)
I started flying wings too :)
Nice job Kelvin
@@kennethbryant2410 thanks ken
Cut or put a duct on the top part of the fuselage so the fan can get more air. I know you would do a good Job at it.
Good stuff
I love that plane
Super cool
Great pursuit
@@thefpvyawthority8106 thanks blue
nice 👍👍👍
suparrrrrrr coolllllllll men 💯
The attention to detail here is top notch. Nice work! How can i make the canopy more clear?
Clean with microfiber and windex or ammonia , then spray again after wiping just to clear off any impurities , leave the spray on there and dip it in quickshine floor shine . Let it sit in a seal container to avoid any fibers and dust settling on it while it cures . Leave it for 48 hours and re dip it until you get the result you want
@@tonyyimbo thanks, I'll try that
@RyanQuellet thanks Ryan. I use chemical guys ultra fine car polish. I polish about 3-4 times with a microfiber. Then I follow with a automotive ceramic coat. I do this process to both the inside and out side of canopy.
next step is obviously a hotas right?
UA-cam channel “Iwright292” does a hotas with a helicopter and it is one of the best I’ve ever seen! He even does a tutorial.
Funny you say your next project will be an A-10 as that is what im currently building. Except I'll be doing twin 90mm and 8S.
Incredible plane. Is flying FPV easier?
That is the kind of plane that a wife divorces over if it flies off into oblivion.
@@IDrone-l5m 🤣
Would love to try fpv sometime
Man, could I just send you the canopy and pay you for your work? I must say very nice work.
Are you using a voltage regulator to the fan because the power is coming directly from the battery? Can you connect it to the 5v voltage supply on the flight control board or an RC type BEC?
@stephanbrown6724 yes. I'm going straight to the battery with a 12v fan and regulator. I didn't use a supply off the board to prevent any chance of browning out the system. I wasnt sure if 12v/9v rail rail on the fc would handle the load of a fan and the o3 air unit
Ok this RC Jet and the setup is amazing. Now everyone wants know how much $
do you have invested including battery and radio. ?
alot?
Do you think the 70mm Raptor is a big enough platform for FPV?
I think so. might be a bit tight. should be able to at least fit a simple setup with head tracker.
Do you think the 70mm f-16 or f-22 would handle the weight of the FPV setup?
@@smoken04 i think so. Might be a tight fit tho
Hi Kelvin, is current sensing required in any way by the Matek H743 FC?
@@polyscient current sensing isn't required for basic flight operation.
Nice setup. I have a similar setup but my fpv gauge micro controller is acting weird. Can you send me the ino files from the cockpit gauge microcontroller?
How are you getting throttle to and from the flight controller? Directly from the battery to the flight controller, then to the ESC?
@DizzyRC directly from battery to esc. Flight controller power is split off the esc power input cable from battery. I do not run power through the flight controller to esc. As it is rated for 150amps and the esc fan combo pulls close to 130amps i felt it was to close for comfort. I use a seperat hall effect current sensor to get current data to the fc.
i spy a tbs caipirinha on the wall…
@@hankyates yes sir. Still got it.