Great idea thanks for sharing,you could put another small zip tie in the rear holes so the battery has two points of contact,yours is too far forward(could slide off in a crash)OR use rubber bands like the Darwin fpv baby ape and Emax tiny hawk 2 come with!
Thanks, nice hint. I have some magic - VTX goes black after some crashes, randomly. But checking if it got losen - no luck. I've just attachet zip tie - hopefully will solve the issue.
Good idea man im gonna do that before i get to crazy with flying it. Kinda new to fpv but ive messed with cheap drones in the past to test the waters. Thanks for the video
Great diagnosis, Micro cracks on solder joints is very common in all electronics. Over time vibration or cold solder joints etc will develop small micro cracks. What you did basically is what is known as reflowing. Have done alot of it on old retro video cartridges & consoles, Sega, Nes, Snes etc. Even vehicles on the instrument clusters. You will get flickering lights, readouts showing only part of number or letters and gauge needles waving around. You go in and reflow the solder joints and will fix the problem in most cases.
I’m stuck in pit mode… only get clear feed at like 1foot…. 😢 it all happened after I changed mainboards new vtx n all, but after seeing everything up got two battery’s flying then red light and no fun… after flashing cli dumping no gyro no Rx… now got it flying but stuck in pit mode….
I had the vtx on my tinyhawk 3 turn off and on mid flight and it turned out one of the connectors broke off and disconnected and reconnected constantly.
Ok, I might have people's problem figured out. I was changing some settings in my drone. When I went to arm it. After I armed it, the drone Vtx stopped working. Freaked me out. So after a while of thinking about it. I unlocked the VTX AGAIN! After that, the drone worked fine again. It might lock after you change settings. So after they are set. If the screen goes crazy and doesn't pick anything up. Try unlocking it again. Hope that fixs your problem, guys. Let me know if it does pls in a reply. Thx
I had a crash last week that busted one of my motors and after I replaced the motor, I noticed that I wasn’t getting more than 20-30ft without losing my video signal. The video feed is still there and seems consistent when the goggles are right next to the quad, but as soon as I fly further away, it gets fuzzy and goes to crap. Could this same issue potentially be causing that, or do you think my vtx got burned up somehow?
Did you check your see if it goes into 200mh. Mine was set to 200mh. But for some reason after I changed other settings it went back to 25mh. So I had to switch again. Also if your vtx is acting funny. Try to unlock the vtx again. If you haven't done that at all. Then I would suggest starting there.
Cool Idea! Lost mine unfortunately and am now on my second baby Ape. Have fun flying!
This has been SUCH a Huge problem. THANK YOU!
Thank you. I just bought one and heard the horror stories about the vtx. So I will be doing that right now. ✅️
Happy flying
Great idea thanks for sharing,you could put another small zip tie in the rear holes so the battery has two points of contact,yours is too far forward(could slide off in a crash)OR use rubber bands like the Darwin fpv baby ape and Emax tiny hawk 2 come with!
Thanks, nice hint. I have some magic - VTX goes black after some crashes, randomly. But checking if it got losen - no luck. I've just attachet zip tie - hopefully will solve the issue.
You might have just saved me from buying a new flight controller. :D thank you Kris
Only 68 likes you deserve much more !
Good idea man im gonna do that before i get to crazy with flying it. Kinda new to fpv but ive messed with cheap drones in the past to test the waters. Thanks for the video
Great diagnosis,
Micro cracks on solder joints is very common in all electronics. Over time vibration or cold solder joints etc will develop small micro cracks.
What you did basically is what is known as reflowing.
Have done alot of it on old retro video cartridges & consoles, Sega, Nes, Snes etc.
Even vehicles on the instrument clusters. You will get flickering lights, readouts showing only part of number or letters and gauge needles waving around. You go in and reflow the solder joints and will fix the problem in most cases.
Thanks for posting! The tip about the velcro was spot on. Fast,easy mod that just makes sense.
Glad it was helpful!
Great video. You need more than just 1😃
The reason is that pinning from 1 board to another on a freestyle drone doesn't ever work for very long
awesome!
I’m stuck in pit mode… only get clear feed at like 1foot…. 😢 it all happened after I changed mainboards new vtx n all, but after seeing everything up got two battery’s flying then red light and no fun… after flashing cli dumping no gyro no Rx… now got it flying but stuck in pit mode….
I had the vtx on my tinyhawk 3 turn off and on mid flight and it turned out one of the connectors broke off and disconnected and reconnected constantly.
Mine got messed up coz I've crashed it a few times hard and actually caused the vtx to move (those pillars got bent or pulled).
Ok, I might have people's problem figured out. I was changing some settings in my drone. When I went to arm it. After I armed it, the drone Vtx stopped working. Freaked me out. So after a while of thinking about it. I unlocked the VTX AGAIN! After that, the drone worked fine again. It might lock after you change settings. So after they are set. If the screen goes crazy and doesn't pick anything up. Try unlocking it again. Hope that fixs your problem, guys. Let me know if it does pls in a reply. Thx
I had a crash last week that busted one of my motors and after I replaced the motor, I noticed that I wasn’t getting more than 20-30ft without losing my video signal. The video feed is still there and seems consistent when the goggles are right next to the quad, but as soon as I fly further away, it gets fuzzy and goes to crap. Could this same issue potentially be causing that, or do you think my vtx got burned up somehow?
Did you check your see if it goes into 200mh. Mine was set to 200mh. But for some reason after I changed other settings it went back to 25mh. So I had to switch again. Also if your vtx is acting funny. Try to unlock the vtx again. If you haven't done that at all. Then I would suggest starting there.
@@unstoppable6047 where can i see if its actually 200mw ?