Can not turn off accessories, ignition, audio unit/radio Mazda 6 and CX5
Вставка
- Опубліковано 26 бер 2021
- Symptoms of malfunction and possible complaints, all happens after the ignition is switched off and gear shift lever in parking position: Accessories stay on, Audio Unit/ Radio doesn't turn off, Power windows operative, Drained vehicle's battery, Can not turn off the ignition.
Part numbers Mazda 6 GJ CX5 KE: KDY0-46-040 for Left Hand Drive. KDY1-46-040 Right Hand Drive (Always check with VIN)
Production Range Mazda 6: from the first model to late 2014, Mazda CX5 KE: from the first model to late 3013 not all countries.
Music: BigCarTheft
Musician: Jason Shaw
URL: audionautix.com
License: creativecommons.org/licenses/... - Авто та транспорт
I discovered that if you apply light pressure to the gearshift knob when in PARK (pulling back towards your knee) you can then turn-off the car. I have been doing his for a few years - works every time.
Yes, and to fix the issue, you can apply some piece of rubber onto the tip of that switch, and the problem will disappear.
THANKS for posting this vid. You are WAY more patient than me. It took me about 1 hour with a LOT of swearing and some crying. Some of those clips are diabolical. All in all I'm NOT impressed with this design. Oh, I used a Dewalt right angle gear 1/4 drive for those two Phillips screws.
Great video! Gets right to the things that need to be done and why and doesn't include a bunch of unnecessary steps. Replaced this switch on my 2014 Mazda 6 today and all is well. Spent about $50 all total including a some plastic pry tools and a tool to pry apart the snap together electrical plugs (almost necessary for the plug that fits into the new switch). The dealer quoted me $800 for the work so save me a bundle.
Thanks for video, unhooking battery was a pain every time I cut car off.
Thanks for watching. That was the only reason for the battery being drained on those cars.
Just finished replacing mine with the help of your video!! Thank you so much. Everything works properly now.
You are welcome.
Thank you for the vid ! I just change mine after suffering with this issue for awhile with my Mazda!
Perfect! Straight to the point
Brilliant! Thanks so much! Job was easy and it's fixed now. Your instructions were great! Thanks
Brilliant is the Apt Word!! Absolutely Brilliant short to the point and FAST!!!!!
Great video.... those pliers those. I need some of those!!!!
Thank you very much. The best video for that problem!
Thank you for speaking so clearly in English which is been so helpful amazing . Save me $$$$
Thank you! Just replaced the part on my Mazda 6. Works like new and the part was $50…I’m happy!
What's the name of the part
@nyashagwangwava4851 Check out the description.
The best ever. Thanks i change my self and hi work.
Great video. Thanks
PROFESSIONAL Video.............Thank you
Great videos with well described and clear commentary. I like those special plug removal pliers. I would love to get some. Do they have a special name?
Thanks a lot. Here is the name: Muromoto Ironworks Merry HS175 C coupling tool 190mm. copy that and search in Google. You can order at Mazda dealership as well.
Thank you for the very good video. The challenge is showing an easier way to get to the switch and you did that nicely. I saw in the comments further down that you identify the special tool to pull the electrical connector from the switch. I'm getting that to make it easier, and some plastic spuds. Do you have any opinion on the parts offered on Amazon versus getting the part from Mazda?
Hey, thanks for watching. As long as the part is genuine, you can buy even on amazon. Someone reported that the pliers are no longer available, but you will remove the connector by pressing it with any tool, even hand.
Thanks!
👏❤
Great video. My daughter used it to change hers, but it is still not shutting down. Is it possible that the new part is bad as well? Also, what purpose does the spring serve?
Most likely the switch unit is not entirely in its place, because those two screws are not tightened. Usually new screws are harder to turn and at certain point you think that's enough, but there is more room to tighten them. The spring is just to keep lever under tension. If you lost the spring and as far as I remember it'll still work.
Thank you for the Video, I've changed the part with a new one, but the problem still persists, do you have any other suggestions please?
Try to tighten those two small screws holding the switch unit, it might be loose and that causes the problem, apart from that we have never had any issues with it.
did you have to bend the arms of both the springs to re-install them into their place?
You talk about override switch spring, I did not need to bend it.
Where to buy that 90 degree screw driver set ?
This is small ratchet, and Philips screwdriver bit.
Does this part match my 2014 Mazda 6 Grand Touring? The part I have looks nothing like this.
I'm not certain about model year, so if you have the same problem, then check at your dealership by VIN number, as far as I remember there wasn't much difference between 6 and CX5
@@JB_Auto Thanks! Great work as well
The key to open that white electric conector where i can bay? The name place.
The pliers, this is Mazda's special tool, you can order it at Mazda dealership, unless available somewhere else, I will check part number and get back to you.
Here is the name: Muromoto Ironworks Merry HS175 C coupling tool 190mm. copy that and search in Google.
Great Video. How this part called? Part no.?
Thanks, the part number is in the description.
I have the same problem but in manual version. Where it was be a problem?
Check the DTCs first, it could be the fault is SSU start-stop unit.
Just replaced my switch according to your instructions… 30 minutes later, great success! Thank you
The only tools I needed were:
-A trim remover tool to not damage the panels
-small phillips
-long skinny flat head
-needle nose pliers to carefully unplug the switch
Whats the replacement piece called i need it for mine
Switch unit for shift lever, part number in the description.
Thanks
Thank you brother. Last 6 months I’m face this same problem
Please tell me the spare parts name
You are welcome. The part number is the description.
How to tfacke altnaor off 2011 kiiia soue
What was the name of the part that they fixed...
shift switch, part no. in the description.
what is the part called?
Switch unit, and the part number is in the description.
My car problem the p not com
This is something that Mazda should have figured out.