Even though I like when you do a couple of service calls per video... start to finish is great. There are a lot of great channels here but you are by far my favorite channel. Thanks for allowing us to join your journey
Nor-cal Dave hits out of the park with this video. Great to see full videos. Lots of learning to be had and your videos make it easy. Thanks Dave. Awesome work service and videoing wise. I do residential and going to be getting into small refrigeration too.
No work going on in H-Town today so I killed an hour watching you work 12 deg this morning and no power I thank God I knew how to run the central furnace off the generator Great video thanks Dave
Watched two 1hr episodes today. This is great training for me since I just started doing similiar work as an apprentice. Diggin this different format of content too. Thank you!
Tricks of the Trade on Bar Coolers & possibly Prep tables -- if the Tstat is bad (no continuity at room temp), the condenser fan will not run, but the evaporator fan does -- use an extension cord hooked to the compressor & wall outlet to verify compressor & fan work. You can also install a jumper between the run & start windings to simulate a start relay -- after applying voltage, pull the jumper.
Loved the Rubix cube job. Couldn’t believe how tight the kitchen was. Pizza shop in town had junk prep table I condemned. I go to another pizza shop in town for a prep table call a few weeks later and there it is? The condemned one. He bought it from his competitor. Those guys have no Conscience.
? If you pull a vacuum and re install the schrader before the systems positive aren’t you allowing the air that’s between the valve and the cap on the tool into the system?? I usually get the system positive before reinstalling the schrader valve. Only issue is you have to expose the micron gauge to the refrigerant psi.
You know your vac pump runs at runs at around 396Hz which is very close to a G4, so maybe you could use the vac pump as a lead in to a song in the key of G4. Sweet vid as always.
Great educated video. First long video from you Dave. I learn how to make condensate loop on this video Had a question how do you tell plug cap tube and low on charge???
Hey Dave, next time smell them yellow cutting boards!!! People think they are stained. Not!!!! Bacteria infested!!! You are a super tech. Meat shop owner in Minnesota. Look up gummy bear bratwurst. You are the best 👌
The fuel is so cheap in the USA, you pay 63$ for 20 galons, thats converted 75 liter, this would cost in europe about 2 € / liter, thats reconverted $174 :-#
Having watched every single one of Chris’s (Stephens) videos, I thought he had it bad, but I’m not feeling sorry for him anymore after having watched this, my first video of yours.
Hey Dave its not in this video. But what is the portable battery operated tub with sprayer that you use to pressure wash the coils on roof condensers ?? I want one.
Awesome video man been watch your content for al little while now. If any one can answer my question. Since it’s pretty doable to replace almost any part of this style of prep table at what point would recommend to replace the whole system? Rather then just making repairs here and there.
Love your vids Dave I’ve been learning so much I have a question for testing purposes only would it be alright to use recovered gas? To be a little more cost effective per say
Nothing like job site Tetris move this to get to that and move that to get to something else been there done that I've done service work in kitchens for electrical and plumbing in it's never fun to keep your boots dry
I'm a rock singer I have been in tour for most of my adult life but I'm wondering why that copper smell tube has to go through that small metal box ,what is the porpoise of the 1/4 quarter inch pipe to seat in that position to what porpoise?? Please explain thank you
I know it’s messing with yo chicken, but thanks for the long video with only one commercial. Great Video Super Dave. PS a crystal ball is telling me Darnold to the 49ers, Jimmy G out.
Even though I like when you do a couple of service calls per video... start to finish is great. There are a lot of great channels here but you are by far my favorite channel. Thanks for allowing us to join your journey
Love the better content. Nice to see you doing the same stuff I do every day, especially being that I took the day off :)
Nice to finally see a full length video. Great job as always Dave
Same day video = high quality creator
Thank you!
Dave working Presidents’ Day wife going to shop for Presidents’ Day especials that is life, good videos Nor Cal the best 👍🏻👍🏻
Nor-cal Dave hits out of the park with this video. Great to see full videos. Lots of learning to be had and your videos make it easy. Thanks Dave. Awesome work service and videoing wise. I do residential and going to be getting into small refrigeration too.
Awesome , superefficient
No work going on in H-Town today so I killed an hour watching you work
12 deg this morning and no power I thank God I knew how to run the central furnace off the generator
Great video thanks Dave
Wow that’s cold. 12 degrees damn.
Nice clean floors 👌🏼
Watched two 1hr episodes today. This is great training for me since I just started doing similiar work as an apprentice. Diggin this different format of content too. Thank you!
Your welcome Zam.
Great vid your longer video are great to watch and help techs like me pick up the good habits keep them coming!!!!
I had a mine it was a evaporator leak or condenser leak great video hvacr mechanic
Love these types of videos !
Tricks of the Trade on Bar Coolers & possibly Prep tables -- if the Tstat is bad (no continuity at room temp), the condenser fan will not run, but the evaporator fan does -- use an extension cord hooked to the compressor & wall outlet to verify compressor & fan work. You can also install a jumper between the run & start windings to simulate a start relay -- after applying voltage, pull the jumper.
Good stuff!! Super Dave out rocking the President's Day🔥🔥🤘🤘
Loved the Rubix cube job. Couldn’t believe how tight the kitchen was. Pizza shop in town had junk prep table I condemned. I go to another pizza shop in town for a prep table call a few weeks later and there it is? The condemned one. He bought it from his competitor. Those guys have no Conscience.
Great job! There's few who understand cap tube systems.
love your doing buddy and joy it.l am pakistan city faisalabad.
Excellent Dave 👍👍👍
🤘⚡️🤘✨
Like that music you're playing that music is what kind of music is
UA-cam non copyright chill music
Def Diggin the “start to finish” videos bro... 🤘🤘🇺🇸🇺🇸
Thanks Jimmy
That was a great watch, good detail on the job you are doing.. Like that coffee mug too!
? If you pull a vacuum and re install the schrader before the systems positive aren’t you allowing the air that’s between the valve and the cap on the tool into the system?? I usually get the system positive before reinstalling the schrader valve. Only issue is you have to expose the micron gauge to the refrigerant psi.
Love the long videos man keep it up
Nice work Dave 👏🏻👏🏻👏🏻😉 prepatitis day!!!
Great job. 200 psi on pressure test will be the best for Cap Tube system Before pump down .
Good stuff brother Dave... thanks for sharing..stay safe and be well.
whats up my norcal pal great vid
Killer work as usual
You know your vac pump runs at runs at around 396Hz which is very close to a G4, so maybe you could use the vac pump as a lead in to a song in the key of G4. Sweet vid as always.
I love you too, bro.
C032CAPT driers are this shit!! 🇺🇸🇺🇸🤘🤘 good repair brotha
im not sure if its cause the university is slow but im loving all the norcal videos. hope you and your family are doing well dave!
Love long form vids
Good one Dave 👍
Love your video. Good job.
Estodo la raza trabajando
u genius norcal....funny guy 2
Great video
Dame gas is cheaper in California than Illinois.
Great educated video. First long video from you Dave. I learn how to make condensate loop on this video
Had a question how do you tell plug cap tube and low on charge???
Or a tap-o- line valve
Very good job ,a query if it is not a bother how much are the fees for that job ? Good life and tank you.
2.52 a gal. Here in my town in the Florida panhandle
you always clean the condenser with freon then check for leaks.tin tirin.
You could tell this was still during the pandemic because of the price of gas in California was under $4/gallon 🤣🤣
Nice 👍
Hey Dave, next time smell them yellow cutting boards!!! People think they are stained. Not!!!! Bacteria infested!!! You are a super tech. Meat shop owner in Minnesota. Look up gummy bear bratwurst. You are the best 👌
Sure would be nice if you would explain what you're doing and why you're doing it instead of just playing music
The fuel is so cheap in the USA, you pay 63$ for 20 galons, thats converted 75 liter, this would cost in europe about 2 € / liter, thats reconverted $174 :-#
Having watched every single one of Chris’s (Stephens) videos, I thought he had it bad, but I’m not feeling sorry for him anymore after having watched this, my first video of yours.
Welcome to the show Scott.
I lay a wet rag over the condenser coil before I blow it out.
I do if food or people are out.
Did you fill with liquid, and then turned the unit on? Wonder after unit was on u we’re filling with gas.
Hey Dave its not in this video. But what is the portable battery operated tub with sprayer that you use to pressure wash the coils on roof condensers ?? I want one.
thank God job
Do you have any cap tube replacement vids?
There in there
Súper 👍💪💪💪
The condition of the restaurants flooring for lack of cleanliness is disturbing in that kitchen. Quite nasty...
I crawl in them all day long Saturday and Sundays too. Usually the floor gets a little cleaning 🧼 from my back. 😂😂😂😂😂😂
Jesus i thought NYC prices were bad. At least we're at 2 and change.
2.48 today
YÉS VERY GOOD 👏👏👏👊👊
Awesome video man been watch your content for al little while now. If any one can answer my question. Since it’s pretty doable to replace almost any part of this style of prep table at what point would recommend to replace the whole system? Rather then just making repairs here and there.
Cost and how beat is unit. Example why install a compressor on a 20 year old unit. That has beat doors and housings.
Presidents Day Prep Table Parade!
Love your vids Dave I’ve been learning so much I have a question for testing purposes only would it be alright to use recovered gas? To be a little more cost effective per say
You need to stick to part 608 epa rules.
@@NorCal-refrigeration thank you so much !!
UA-cam Gold!
Eye-hand ordination
If I ever travel to California, I will first watch Dave's videos to find out which restaurant to eat at and which one not :)
Nothing like job site Tetris move this to get to that and move that to get to something else been there done that I've done service work in kitchens for electrical and plumbing in it's never fun to keep your boots dry
What does something like this cost as far as the service/repairs?
What did you do with the gas you added to determine whether it was a leak or blocked cap tube
I'm a rock singer I have been in tour for most of my adult life but I'm wondering why that copper smell tube has to go through that small metal box ,what is the porpoise of the 1/4 quarter inch pipe to seat in that position to what porpoise?? Please explain thank you
It’s the discharge line from compressor it’s hot. The pan catches the condensation the tube evaporates it’s and pre cools the line.
Does that vangina have a 6 banger in it.
2022 now its $6 a gallon,probably be$10 a gallon by the time that clown gets out of office.
3.19 for gas
Yummy, that floor is so...
Was the second place the same place you had to fix the wiring on top of the walk in?
Yes
I know it’s messing with yo chicken, but thanks for the long video with only one commercial. Great Video Super Dave. PS a crystal ball is telling me Darnold to the 49ers, Jimmy G out.
Darnold was a fat kid and Jimmmy G wins ( when healthy ). And Kyle is soy. Watson or Russell Wilson only over jimmy G.
Don't throw your hoses on your gauges in the dirt like that
Ok super tech
Wow $3.19 for gas here in st.louis MO i paid $1.99 at Sam's
Don’t worry by summer it will be 5$ and climbing.
@@NorCal-refrigeration thanks to idiots voting for biden
👌👌👌👌🛠️🛠️🛠️
Whats the difference in your veto bags tool wise. How do you pick which one. I see alot of guys have two bags What's that about
Tried to have a light weight quick check bag. But more stuff finds its way into it.
Am I the only one that cringes that the amount of dirt underneath all the equipment
It got the deep clean today. You can here them in the background
What's the name of that music is playing I love but Where can I get it
Older system last longer top of the line through generation system to
I like to know know that stuff what you doing on the prep table
What do you call a guy with no arms and no legs water skiing?
Skip
Don’t touch the table top with that Matt glove nor cal
What do you call a guy with no arms and legs in a trunk?
Jack
That music is from early 80's porno's!
Sounds like your a connoisseur.
#343 Thumbs uP
that floor is gross>!!!!
:-)
What do you call a guy with no arms and no legs hiding in a lingerie drawer?
Teddy. What do you call him if you throw him across a lake?
@@NorCal-refrigeration idk?
@@tomsanders3032 skip