Back in the '70's my father in law had a Dodge which had a noisy rear end. He subsequently found out later that the dealer repaired it by sticking a rag in the housing!
Had one of these , a 4.10 also , from a 69 road runner 440-6 , I put it in a 66 coronet I had with a 69 road runner 383 I built up , guy with the 440-6 road runner didn't like the gas mileage and I traded him my 3,55 eaton , a great deal for me ! Had it for four years and never had a lick of trouble with it , bulletproof !
This is the second time I have watched this. An easier way to get the carrier out is to use a wrench and socket. Place the wrench on the ring gear bolt at the bottom. Use the socket to turn the pinion gear. The carrier will roll out. Keep in mind to keep the shims for each side separated. This is necessary it you are reinstalling the original carrier assembly for the proper preloading.
Nick...I bought a 1984 Dodge 3/4 ton pick up years ago. I was going to change the fluid in the read diff. (Dana 60) and when I took the rear cover off it was packed with mud. Even the axle tubes had mud in them. LOL. You know it never made any noises the whole time I drove it. I did replace the bearings and seals. I used a broom handle and rags to clean the axle tubes. On the truck Dana 60's I always pack the outer axle bearings in red bearing grease as extra protection.
Morning. Got my morning coffee. Now I ready to watch the video. Ford Motor gear and axle in 1967 cut all the dana gears. I should know as i worked in the gear cutting section.
Here in Australia ,a series of ord F100 pickups were sold with Dana 60 rear ends and a 300 Six. i have only ever seen one and it was in a country town wrecking yard . The diff would never wear out with those old sixes...😁
I ordered and installed a Strange Dana 60 in my pro touring 72 Dodge Challenger with disc brakes and a 1350 yoke with a Detroit Tru Trac gear driven differential...expensive yes but bulletproof!!
Mophorn Differential Housing Spreader for Dana Axles Fits for 30 44 60 70 &80 Series Always worked for me just don't over stress the housing. A must need for reassembly and set up.
Wow! Those Dana 60 rear ends were used alot back on the day. I know the sure grip and posi wasn't common but alot of pickup trucks had a Dana 60. I have a 1972 Ford F250 with a Dana 60 - 3.54 gear ratio. Had to replace rear cover because the plug threads pushed out the back of the cover. I did notice the W stamped on the plug. Thankfully, it wasn't difficult to obtain a cover aftermarket as it looks like the basic Dana 60 diff housing remained unchanged for years. BTW here in the US, the bearing itself is called the cone and the race is the cup. Great video and educational.
@@SuperDd40 if the aluminum you're referring to is the rear diff cover its actually stamped steel. It's just so thin (not due to rust but made that way). They punched the plug hole and then threaded the part that was pushed inward. It wasn't a good design because the steel was so thin. And then after tightening the plug a little harder than I should have just pushed the threaded portion through and ripped it. I wanted an original replacement but only saw one in chrome plate. Found a heavier steel cover with Summit and it's been great. Hope you are enjoying that truck. Those 4.10's might not give you very high speeds on the highway if you have stock size tires. :)
@@stephensaasen8589 I'm referring to the new F series truck made from beer can material. Right now i'm restoring the truck so i have a different kind of enjoyment (fixing holes , surface rust, painting the undercarriage...) As for the highway speed it also have a Dough Nash Enterprise overdrive so should be ok. I'll tell you about it in 2 years.
@@SuperDd40 that sounds great. Yeah, I can't believe it either about those new Ford trucks made of aluminum. May not rust so easily but to make them stronger you'd have to make it heavier. Good luck with the '67. Nothing like restoring old iron.
Dana's are a PITA and time consuming to get perfect..A housing expander is a mandatory tool for the purpose of easy carrier removal and install while setting preload...Since the carrier bearings have the shims between the carrier and bearing, I make "Test" bearings.. Use a flap wheel to enlarge the inner part of the carrier and pinion bearings just enough to slide them on by hand...I also reduce the outer diameter of the rear pinion bearing race to install the shims for adjusting pinion depth..Once correct shims, backlash and pattern is established, Then press on the new bearings and install with pinion seal..Some fine tuning adjustment of backlash may be needed..Takes me about an hour to do a gear change now..
Best way to start a Monday morning off is with a new video from nicks garage thanks for sharing George and great camera work like always George and god bless you guy's
I was lucky. I had a great auto shop teacher in high school. I still do drum and disk brakes as he taught me. I always wear safety glasses. I can still hear his instructions. He really made an influence on me, he nominated me for industrial arts student of the year and I won that certificate. I knew where he lived and when my son was young and I was teaching him auto mechanics, I drove by to say hi and to show him my son. Sadly, his widow told me he died of cancer years ago. I wish I had visited sooner.....
I lunched the spider gears in my dana70 posi at the strip in my truck. Then I upgraded to a Dana 80 with an air locker. That moved the problem to snapping the 1.62” diameter axles. Changed to a s135 with a 13” ring gear and finally quit breaking rears. My racer weighed 7200lbs though. 😎
Case spreader is a must in my opinion, did a lot of 60’s with one Makes the job easier and saves a lot of time. Each to his own. My first car was a 69 Dodge Coronet r/t, 440 auto, yellow ,black vinyl top, white interior,console,miss that car lol thanks Nick
Great day, guys!! Another great video from Nick's garage: I like seeing things be disassembled, to learn what's inside and how it does what it does. I got a chuckle from the look on Leo's face after the oil drain pan incident, like, "I hope he's not gonna kill me!" But, Nick seems like a very patient man: you have a fantastic teacher, Leo, and you're an eager student, a combo that's hard to beat!!! Fantastic week to you all, and a happy Thanksgiving as well!!
O M G! I'm in love with another man's car! Nick, check out Jay Leno's 62' 426, wedge, 4 speed, Polara in Red!!!! (That's a mouth full but worth it!) It was just posted. It is one of the first muscle cars. I used to despise Jays collection, but after a few years it's become apparent that he really keeps it alive. The way of the muscle car will never die. T.
They are strong enough for one ton trucks and buggys for rock crawling when used for that they usually have eight lug nuts, wish I had one with the five on four and one half for a B body Mopar to put under my 73 charger, thanks for sharing this information on this differential most people have no idea how hard it is to get all the tolerances just right and how important it is, you really know your business MrNick
I am a retired Industrial Mechanic.Been in a lot of gear boxes.But none of them never smelt as bad as when I used to change my 3:42 Differential on my million km. Silverado.Use to change the gear oil about every 200,000 and did it stink.I believe it was 80w90 weight oil.Yeah Leo put safety Glasses on when using that punch and hammer.Seen a few eye injuries in my 44 years of work.
Thanks for sharing another great video post Nick. I’ve worked on Dana-60’s before. 9”Ford rears too. Both great bulletproof pumpkins. I’ve never heard a “wrench” called a “key”. That’s a new one. God bless and best of luck to you and yours 👍🏼🍀
I had a Henrys magnesium Dana 60 with Chrome molly axle tubes on my old race race car, I got it from a guy that kept snapping axles, I put a set of Mark Williams 40 spline gun drilled axles in it and never had an issue with it after that. It was setup with full floating axles it was a nice bit of kit. I replaced a Ford 9" with it that also had full floating axles but only 31 spline axles that had snapped an axle in the previous race.
Technical name is Cup & Cone bearings...The 'race' is the cup. The adjustment is called 'preload'. Nothings wakes up a car, like a good ratio in the rear end. 3.73 and up for a muscle car...
Nick:gr8 video and job as usual. Top tip, turn the differential housing with pinion yoke down towards the floor. This way you can pry the gear set out while preventing it from falling out onto the floor and also possibly pinching your fingers. I've done it myself many times before and had no problems in doing it this way. Say hello to Leo and the rest of your staff. Have a gr8 God bless day.
The look he gave after dumping the gear oil was priceless... Great job and keep him employed.. I had gear lube run down my arm into my side doing a trans once.. Nasty.. I once brought in my car to have the pinion seal replaced. About a week later I'm driving and did a shift and there was a huge bang.. Yep they never tightened up the pinion and it cam lose and wrecked a 3:42 Pontiac drop out posi in my station-wagon..
I would never let anyone touch a rear-end unless I knew they were qualified. I hear these stories all the time, and it truly isn't difficult to set one up.
@@NicksGarage Good morning George, I'm always ready for another episode of Nick's Garage, which is why I look forward to Monday morning. I really enjoyed this video, it has been a long time since I last worked on a Dana 60. I helped my friend refresh the rear end in his 1970 Cuda 440 6 pack 4-speed. It was getting a little noisy, so we replaced all the bearings, and put everything back together the way it came apart, the gear pattern, and backlash were perfect. I can still smell the gear oil to this day!
Nick, I can't believe that you don't have a case spreader. That was a Chrysler special tool. We used it a lot at the Dodge dealership, but mostly on pickups.
I do not have one. But I do not do many rear ends. I know of a shop that does rear ends all day long and they do not have a case spreader. Shame on them.
@@nickpanaritis4122 Like your videos Retired mechanic GM Dealership most of my life. Use to sweep up and clean parts at Mr Norms Grand Spaulding Dodge when I was a youngster. Case spreaders are cheap less than a $100.00 US. Also very important that a dial indicator is used with the spreader. There is a max spread or you can crack the case. That is why you had a hard time pulling the carrier. When you are setting back lash and rotational torque trying to pull the carrier in and out to make the adjustments is very difficult.
Morning Nick, Leo & George. Well that diff didn't look to bad inside and good on the last owner for putting rags inside to protect it from the elements. Nick over here in New Zealand we refer to that spanner you were talking about as a ring & open end and a wrench is what's known as a crescent otherwise all good. Have a great week guys.
Keep this trick I devised years ago for the future when you do carbutator work.. Try this... Heat the plastic tube from the carb cleaner spray with a lighter (about 1/4-1/2 inch from the end. Then pull on each end of the tube to stretch it. This makes the outer/inner tube diameter smaller and more of a pin point. When the melted plastic solidifies, use small wire clippers or nail clippers to snip the tube at the smallest diameter that still provides flow when spraying. The cleaner comes out like a pin point pressure washer and the shrunken plastic tube end fits inside whatever port your spaying thru. You can also do the same to create 90 degree angles in the plastic tube to spray sideways inside long venturi tubes. I used to make/keep custom tubes around for these situations. Hope this makes sense. BTW.... Great videos.
The Dana 60, now I am on my second one. My first one was a 1966 Plymouth Belvedere ll with the 383 and Torquflite transmission. Now I have a 440 in a 74 Dodge Superior
It rarely needs a mend It's the legendary Dana 60 rear end Nick is dropping knowledge from practical experience you don't get in college Nick knows every ratio for every model of car This is a 410 ratio once it's done it'll take the new customer far This will suit any E code for tranferring that power to the road Fully ready to go under a hard load Water and oil do not mix It's a sign that says this Dana might need a fix Nick and Leo are not worried because they've got a whole bag of clever tricks Keeping it old school that's what makes Nick's Garage every Monday so very cool
When I sold my 1968 GTX, the kid that bought it spun the tires and slid into a curb, bending the axle flange. He came back and paid me to replace the axle shaft. I bought the new replacement Dana 60 axle shaft from a Dodge dealer. It had the correct early splines, but it was not thinned in the middle, like the factory installed axle shaft was and it was much heavier. I guess that saved them some machining.
Dr. Nick, yes that gear oil stinks!, years back I helped my friend rebuild a DAH- NA 60, was not a easy job , but we did put it back in his 1970 440 cuda, bty I like these type of how to videos, well done George, cheers.
I am in Canada and have never heard a wrench called anything but a wrench or spanner. The only "key" named tool common to this industry is Allen or Hex key. Must be a French or Quebec thing.
Great video Nick!!! I like how the parts & shims were marked before being dis-assembled... It really helps it to go together properly... Those ring & pinion gears don't seem to look bad at all... I imagine the Differential carrier case, spider gears, spider, side gears & clutch's are all in good shape as well... Will there be an episode on inspecting them too? From what I have heard, the Dana 60's were originally designed for the heavy use of P/U trucks... The 3/4 and 1-ton trucks had the extra load carrying capability by using the 'full floating' hubs & bearing assemblies with 8-lug bolts for the brake drum/rotor & wheels, while the 1/2-ton trucks and muscle cars used the lighter duty 'Semi-floating' type of hubs & bearing assemblies with 5 lug bolts (Ford, Mopar, I-H) or 6 lug bolts (GM) for the brake drums/rotors & wheels... These stout TRUCK rear axles proved to be a very good choice for the high Power & Torque of the muscle cars...
Thanks Nick I learned alot today from your video thanks for sharing your knowledge it is greatly appreciated and best wishes to you and the crew during the holidays
Nick at my Grandfather's garage, He had gear oil from the 1920s and 30s made from whale oil. It has an incredibly distinct smell, but was the best gear oil you could get or use.
i used a case spread years ago, also rear end shims for the side gears and cupped ones for the spider gears they were select fit .i don't remember if it was a jag an mg or aston ,it was foreign.
Great video! Nick, Consider next time trowing a mag base on and getting a base line for your backlash. Sometimes I even but some marking compound on, put a little residence on that pinion and roll the the ring gear a few times, just so I get a good idea of what to expect. Usually if Im trying to go back together with all the same components. Keep up the great work!!
Great video, Nick! I have long been a fan of the Dana axles. There's a Dana 44 in the rear of my 79 Jeep CJ5, and a Dana 30 in the front. Such a timeless pieces of engineering artwork. Thanks for doing this great breakdown video!!!!
If you ever have problems getting the bearing races out , weld a bead around the center of the race and when it cools , it will come right out . It shrinks the race !
I'm a certified welder of 40 years . I have my own portable welding service for 35 years and most of that has been working on equipment . This technic works 100% of the time . I learned this through trial and error . It doesn't have to be a pretty bead either lol . Stick or wire will work !
Great video Nick .. very informational for viewers who are new at something like this .. you do a great job at explaining…a little side note .. in order to not smell the gear oil…a clothes pin is usefull on the nose… hehe lol 🤣
always pull the oil plug to check condition of oil with Q-tip or water present if third member was out already. in car once had a diff filled with wood chips for gears were pitted so bad from water contamination from a flood
A little trick...To keep the axle tubes from turning in the case housing we drilled and taped 3 3/8 inch grade 8 bolts fine thread bolts threw the case housing in 3 different spots on each side. Then install bolts and cut to length then use red loctite to hold them in and keep them from leaking gear oil. You can weld the tubes to the case but it is way to easy to warp the tubes. You can use this trick on any rear end. I have seen my share of tubes twisted and its dam near impossible to fix.
So crazy. My 78 f250 has a Dana 60 w a 4:10 gearing. Center section looks identical. Crazy how everything from those era’s are so identical between makes
Love old school. Now 67 yrs young I had a 1969 Camaro SS 396 CID 375 HP posi traction 4 speed diff was 4/10 gears. What I wouldn’t do to have her back. Original came as yellow with black wide strips. A ripper.
In Australia we call it a spanner or open ender Nick..or a nut f....r because it rounds the nuts of if doesn't fit properly.. good show on the Dana 60 mate
Dana 60 ,best diff of them all. Unfortunately we never had these in our Australian mopars. We had Borg Warner crap so I built a nine inch for it. Sick of blowing up Borg Warner diffs every week.
Very informative, question for you I think I counted 10 bolts on cover. I have often heard people refer to different diffs by different amount of bolts on cover.
Hey Nick I know you are busy as two Nicks , but check out Gale Banks vids on differential covers and oil flow and cooling of the differential. Point is, stay with stock cover, or get Bank's cover. No overheating the oil, no aeration either.
NICK, I LOVE the smell of gear oil, ATF, paint, silicone, chassis lube, gasoline, diesel fuel, ect. I HATE the smell of perfumes, colongnes, body powders, ect. !
Cover was reinstalled and rags were pushed in the pinion and axle openings to prevent sandblast from entering.
Now I can be LIVE all the time 🤣🤣🤣
What about the open vent hole in the axle tube?
@@55desotomine it'll get the proper attention
@@55desotomine I had a plug installed.
Back in the '70's my father in law had a Dodge which had a noisy rear end. He subsequently found out later that the dealer repaired it by sticking a rag in the housing!
Had one of these , a 4.10 also , from a 69 road runner 440-6 , I put it in a 66 coronet I had with a 69 road runner 383 I built up , guy with the 440-6 road runner didn't like the gas mileage and I traded him my 3,55 eaton , a great deal for me ! Had it for four years and never had a lick of trouble with it , bulletproof !
This is the second time I have watched this. An easier way to get the carrier out is to use a wrench and socket.
Place the wrench on the ring gear bolt at the bottom. Use the socket to turn the pinion gear. The carrier will roll out.
Keep in mind to keep the shims for each side separated. This is necessary it you are reinstalling the original carrier assembly for the proper preloading.
Nick...I bought a 1984 Dodge 3/4 ton pick up years ago. I was going to change the fluid in the read diff. (Dana 60) and when I took the rear cover off it was packed with mud. Even the axle tubes had mud in them. LOL. You know it never made any noises the whole time I drove it. I did replace the bearings and seals. I used a broom handle and rags to clean the axle tubes. On the truck Dana 60's I always pack the outer axle bearings in red bearing grease as extra protection.
Professor Panaritis, Lecture Hall has started, take notes!
Morning. Got my morning coffee. Now I ready to watch the video. Ford Motor gear and axle in 1967 cut all the dana gears. I should know as i worked in the gear cutting section.
Morning! That is awesome! Thanks for watching and for the memory.
Here in Australia ,a series of ord F100 pickups were sold with Dana 60 rear ends and a 300 Six. i have only ever seen one and it was in a country town wrecking yard . The diff would never wear out with those old sixes...😁
I ordered and installed a Strange Dana 60 in my pro touring 72 Dodge Challenger with disc brakes and a 1350 yoke with a Detroit Tru Trac gear driven differential...expensive yes but bulletproof!!
Mophorn Differential Housing Spreader for Dana Axles Fits for 30 44 60 70 &80 Series Always worked for me just don't over stress the housing. A must need for reassembly and set up.
Installing a set of 4.30 gears in a ford 8.8 here shortly. Great work Nick and crew.
Sounds great!
Wow! Those Dana 60 rear ends were used alot back on the day. I know the sure grip and posi wasn't common but alot of pickup trucks had a Dana 60. I have a 1972 Ford F250 with a Dana 60 - 3.54 gear ratio. Had to replace rear cover because the plug threads pushed out the back of the cover. I did notice the W stamped on the plug. Thankfully, it wasn't difficult to obtain a cover aftermarket as it looks like the basic Dana 60 diff housing remained unchanged for years. BTW here in the US, the bearing itself is called the cone and the race is the cup. Great video and educational.
1967 F250 here 352FE , C6 trans with a 4.10 Dana 60. Alumunimum suck. ;)
@@SuperDd40 if the aluminum you're referring to is the rear diff cover its actually stamped steel. It's just so thin (not due to rust but made that way). They punched the plug hole and then threaded the part that was pushed inward. It wasn't a good design because the steel was so thin. And then after tightening the plug a little harder than I should have just pushed the threaded portion through and ripped it. I wanted an original replacement but only saw one in chrome plate. Found a heavier steel cover with Summit and it's been great. Hope you are enjoying that truck. Those 4.10's might not give you very high speeds on the highway if you have stock size tires. :)
@@stephensaasen8589 I'm referring to the new F series truck made from beer can material. Right now i'm restoring the truck so i have a different kind of enjoyment (fixing holes , surface rust, painting the undercarriage...) As for the highway speed it also have a Dough Nash Enterprise overdrive so should be ok. I'll tell you about it in 2 years.
@@SuperDd40 that sounds great. Yeah, I can't believe it either about those new Ford trucks made of aluminum. May not rust so easily but to make them stronger you'd have to make it heavier. Good luck with the '67. Nothing like restoring old iron.
Wtf is a ground gear ? Is it Canadian for ring ?
Thanks for doing the Dana 60-showing my age by bringing back old memories.
Dana's are a PITA and time consuming to get perfect..A housing expander is a mandatory tool for the purpose of easy carrier removal and install while setting preload...Since the carrier bearings have the shims between the carrier and bearing, I make "Test" bearings.. Use a flap wheel to enlarge the inner part of the carrier and pinion bearings just enough to slide them on by hand...I also reduce the outer diameter of the rear pinion bearing race to install the shims for adjusting pinion depth..Once correct shims, backlash and pattern is established, Then press on the new bearings and install with pinion seal..Some fine tuning adjustment of backlash may be needed..Takes me about an hour to do a gear change now..
Best way to start a Monday morning off is with a new video from nicks garage thanks for sharing George and great camera work like always George and god bless you guy's
Thanks 👍
That Leo is a keeper Nick, one day you may be going to HIM for advice!
Nick's the Auto Shop teacher you wish you had in high school.
Agreed
I was lucky. I had a great auto shop teacher in high school. I still do drum and disk brakes as he taught me. I always wear safety glasses. I can still hear his instructions. He really made an influence on me, he nominated me for industrial arts student of the year and I won that certificate. I knew where he lived and when my son was young and I was teaching him auto mechanics, I drove by to say hi and to show him my son. Sadly, his widow told me he died of cancer years ago. I wish I had visited sooner.....
I had a shop teacher just like him but it was for auto body. Great guy as well loved learning all the old school tricks and this was over 30 years ago
When I owned my '71 Charger R/T 4-speed, I bragged more about its Dana 60 than I did the 440.
as soon as you guys cracked the cover , said to my self if gonna stink like hell
that one reason i hate to work on diffs
Learn something every time I watch Doctor Nick operate
Thanks for watching.
Mornin Mr Nick! Have a Great week!! Yea, I spilled a quart of 90 weight gear oil in my Ford Pinto. The nasty smell never went away.
Thanks. You too!
Nick has a lot of knowledge on those mopars and other brands Gm , Ford's. Nick is a awesome man. Keep up the Good work Nick's Garage.👍
I lunched the spider gears in my dana70 posi at the strip in my truck. Then I upgraded to a Dana 80 with an air locker. That moved the problem to snapping the 1.62” diameter axles. Changed to a s135 with a 13” ring gear and finally quit breaking rears. My racer weighed 7200lbs though. 😎
I've heard people complain about the weight of the Dana diffs but never hear a complaint about the strength. Well done Nicks Garage crew
Same with Iron Block vs Aluminum Engines .... I'll take the extra weight if it is more durable
The Ring and pinion and carrier are massive. Wow! Beautiful differential. And anyone who has set one up knows the knowledge required.
Right on. Nothing but beefy parts in this one.
Especially nice camera angles and lighting on this video. I like the overhead shots.
Thanks!
Case spreader is a must in my opinion, did a lot of 60’s with one
Makes the job easier and saves a lot of time. Each to his own. My first car was a 69 Dodge Coronet r/t, 440 auto, yellow ,black vinyl top, white interior,console,miss that car lol thanks Nick
Great day, guys!! Another great video from Nick's garage: I like seeing things be disassembled, to learn what's inside and how it does what it does. I got a chuckle from the look on Leo's face after the oil drain pan incident, like, "I hope he's not gonna kill me!"
But, Nick seems like a very patient man: you have a fantastic teacher, Leo, and you're an eager student, a combo that's hard to beat!!! Fantastic week to you all, and a happy Thanksgiving as well!!
Nick, you always play with my favorite toys!
The way of the muscle car will never die.
T.
Thanks for playing with us, Tom.
O M G!
I'm in love with another man's car!
Nick, check out Jay Leno's 62' 426, wedge, 4 speed, Polara in Red!!!!
(That's a mouth full but worth it!)
It was just posted.
It is one of the first muscle cars.
I used to despise Jays collection, but after a few years it's become apparent that he really keeps it alive.
The way of the muscle car will never die.
T.
Nick ... just got me a High Definition TV and MAN ITS LIKE ACTUALLY BEING THERE!!!!
Nice!
@@NicksGarage it's like I'm ACTUALLY THERE
@@NicksGarage can't wait to see how it does on Friday
@@NicksGarage 50 inch Diagonal High Definition TV
Might not be quite as crisp with the live broadcast.. but we will do our best.
They are strong enough for one ton trucks and buggys for rock crawling when used for that they usually have eight lug nuts, wish I had one with the five on four and one half for a B body Mopar to put under my 73 charger, thanks for sharing this information on this differential most people have no idea how hard it is to get all the tolerances just right and how important it is, you really know your business MrNick
Hi Nick,
In Australia we call it a spanner. Open ended and ring to be exact.
Cheers,
Jason.
Combination Spanner, open end and ring spanner.
Nick I thumbs up you twice everytime on my phone and my firestick
Thanks Darren.
I am a retired Industrial Mechanic.Been in a lot of gear boxes.But none of them never smelt as bad as when I used to change my 3:42 Differential on my million km. Silverado.Use to change the gear oil about every 200,000 and did it stink.I believe it was 80w90 weight oil.Yeah Leo put safety Glasses on when using that punch and hammer.Seen a few eye injuries in my 44 years of work.
Thanks for sharing another great video post Nick. I’ve worked on Dana-60’s before. 9”Ford rears too. Both great bulletproof pumpkins. I’ve never heard a “wrench” called a “key”. That’s a new one. God bless and best of luck to you and yours 👍🏼🍀
I had a Henrys magnesium Dana 60 with Chrome molly axle tubes on my old race race car, I got it from a guy that kept snapping axles, I put a set of Mark Williams 40 spline gun drilled axles in it and never had an issue with it after that. It was setup with full floating axles it was a nice bit of kit. I replaced a Ford 9" with it that also had full floating axles but only 31 spline axles that had snapped an axle in the previous race.
I just bought one of those last week.
A Mopar rear end being worked on,two Mopar motors behind and a bb Camaro on the lift. I love this show.
Lots more in the shop.
Great Monday morning at Nick's Garage! Hope all of you have a great week! Bill from Linglestown Pennsylvania
I find myself hoping to see a Lemon Twist Charger 500. But actually, anything from Nick's Garage is just fine.
We're hoping to see it very soon too.
@@NicksGarage cant wait to see it finished Nick out in the sun, show winner for sure
Thanks guys for another informative video. I always learn something new. Now time for some coffee in my Nick's Garage mug!
Technical name is Cup & Cone bearings...The 'race' is the cup. The adjustment is called 'preload'. Nothings wakes up a car, like a good ratio in the rear end. 3.73 and up for a muscle car...
Nick:gr8 video and job as usual. Top tip, turn the differential housing with pinion yoke down towards the floor. This way you can pry the gear set out while preventing it from falling out onto the floor and also possibly pinching your fingers. I've done it myself many times before and had no problems in doing it this way. Say hello to Leo and the rest of your staff. Have a gr8 God bless day.
Good idea. I used the stand that I had for diff display. Need to fabricate the stand to turn over.
The look he gave after dumping the gear oil was priceless... Great job and keep him employed.. I had gear lube run down my arm into my side doing a trans once.. Nasty.. I once brought in my car to have the pinion seal replaced. About a week later I'm driving and did a shift and there was a huge bang.. Yep they never tightened up the pinion and it cam lose and wrecked a 3:42 Pontiac drop out posi in my station-wagon..
I would never let anyone touch a rear-end unless I knew they were qualified. I hear these stories all the time, and it truly isn't difficult to set one up.
the look of FFFFFFFFFFFFFFFFFFFUDGE
Good morning Nick, A good way to start a Monday, with a little MOPAR to make things better..
Good morning, sir. Thanks again for joining us. Your timing is always impeccable!
good morning eugene
@@NicksGarage Good morning George, I'm always ready for another episode of Nick's Garage, which is why I look forward to Monday morning. I really enjoyed this video, it has been a long time since I last worked on a Dana 60. I helped my friend refresh the rear end in his 1970 Cuda 440 6 pack 4-speed. It was getting a little noisy, so we replaced all the bearings, and put everything back together the way it came apart, the gear pattern, and backlash were perfect. I can still smell the gear oil to this day!
@@danohstoolbox Good morning Danoh, I hope everything is going good for you, all is well here in Texas.
I was hoping to see your beauty, but alas, it's Dana time.
Nick, I can't believe that you don't have a case spreader. That was a Chrysler special tool. We used it a lot at the Dodge dealership, but mostly on pickups.
I do not have one. But I do not do many rear ends. I know of a shop that does rear ends all day long and they do not have a case spreader. Shame on them.
@@nickpanaritis4122 Like your videos
Retired mechanic GM Dealership most of my life. Use to sweep up and clean parts at Mr Norms Grand Spaulding Dodge when I was a youngster. Case spreaders are cheap less than a $100.00 US. Also very important that a dial indicator is used with the spreader. There is a max spread or you can crack the case. That is why you had a hard time pulling the carrier. When you are setting back lash and rotational torque trying to pull the carrier in and out to make the adjustments is very difficult.
@@backnine . Good point.
Morning Nick, Leo & George. Well that diff didn't look to bad inside and good on the last owner for putting rags inside to protect it from the elements. Nick over here in New Zealand we refer to that spanner you were talking about as a ring & open end and a wrench is what's known as a crescent otherwise all good. Have a great week guys.
Keep this trick I devised years ago for the future when you do carbutator work..
Try this... Heat the plastic tube from the carb cleaner spray with a lighter (about 1/4-1/2 inch from the end. Then pull on each end of the tube to stretch it. This makes the outer/inner tube diameter smaller and more of a pin point. When the melted plastic solidifies, use small wire clippers or nail clippers to snip the tube at the smallest diameter that still provides flow when spraying. The cleaner comes out like a pin point pressure washer and the shrunken plastic tube end fits inside whatever port your spaying thru.
You can also do the same to create 90 degree angles in the plastic tube to spray sideways inside long venturi tubes.
I used to make/keep custom tubes around for these situations. Hope this makes sense. BTW.... Great videos.
As you were taking the diff cover off my nose was already wrinkling up! I remember that smell well. Thanks for the great videos
The Dana 60, now I am on my second one. My first one was a 1966 Plymouth Belvedere ll with the 383 and Torquflite transmission.
Now I have a 440 in a 74 Dodge Superior
Nick please make another video of over hauling the sure grip member I would really enjoy seeing this
Interesting idea.
It rarely needs a mend It's the legendary Dana 60 rear end Nick is dropping knowledge from practical experience you don't get in college Nick knows every ratio for every model of car This is a 410 ratio once it's done it'll take the new customer far This will suit any E code for tranferring that power to the road Fully ready to go under a hard load Water and oil do not mix It's a sign that says this Dana might need a fix Nick and Leo are not worried because they've got a whole bag of clever tricks Keeping it old school that's what makes Nick's Garage every Monday so very cool
Roberto, the Dana 60 of Rhymes.
@@NicksGarage Bless your heart Big ups your chest Nick's Garage is the best!
Hello, Nick. Richard here. I owned a 95 G.M.C. van. G3500,one ton van, Vandura. It had a Dana 60 rear end
When I sold my 1968 GTX, the kid that bought it spun the tires and slid into a curb, bending the axle flange. He came back and paid me to replace the axle shaft. I bought the new replacement Dana 60 axle shaft from a Dodge dealer. It had the correct early splines, but it was not thinned in the middle, like the factory installed axle shaft was and it was much heavier. I guess that saved them some machining.
good morning nick snow day here today its that time of year have a great week
Spring is coming!
One of the best street rear ends from the era, they would take quite a beating and come back for more
Dr. Nick, yes that gear oil stinks!, years back I helped my friend rebuild a DAH- NA 60, was not a easy job , but we did put it back in his 1970 440 cuda, bty I like these type of how to videos, well done George, cheers.
The combination wrench is also called a "spanner" in some parts of the world.
Right on.
It can be called a combination spanner, an open-ended spanner, or a ring spanner. Been using 'em for 40 years on various aircraft in the UK.
I am in Canada and have never heard a wrench called anything but a wrench or spanner. The only "key" named tool common to this industry is Allen or Hex key. Must be a French or Quebec thing.
Yea l was wondering about sand getting inside....But l see where you reinstalled the cover....Thanks Nick Leo and George...!
Great video Nick!!! I like how the parts & shims were marked before being dis-assembled... It really helps it to go together properly... Those ring & pinion gears don't seem to look bad at all... I imagine the Differential carrier case, spider gears, spider, side gears & clutch's are all in good shape as well... Will there be an episode on inspecting them too? From what I have heard, the Dana 60's were originally designed for the heavy use of P/U trucks... The 3/4 and 1-ton trucks had the extra load carrying capability by using the 'full floating' hubs & bearing assemblies with 8-lug bolts for the brake drum/rotor & wheels, while the 1/2-ton trucks and muscle cars used the lighter duty 'Semi-floating' type of hubs & bearing assemblies with 5 lug bolts (Ford, Mopar, I-H) or 6 lug bolts (GM) for the brake drums/rotors & wheels... These stout TRUCK rear axles proved to be a very good choice for the high Power & Torque of the muscle cars...
Thanks Nick I learned alot today from your video thanks for sharing your knowledge it is greatly appreciated and best wishes to you and the crew during the holidays
Thank you!
Does Nick mind if fans drop in to say hi?Huge fans from Woodstock Ontario,Keep up the great work guys.
We love to meet viewers. Just be warned the place can be very busy sometimes.
Nick always showing us the goods Cant wit for Eugene's Charger update !
Us too!!
Nick at my Grandfather's garage, He had gear oil from the 1920s and 30s made from whale oil. It has an incredibly distinct smell, but was the best gear oil you could get or use.
Nick, your the master! I put D60s out of a 79 F350 in my 81 Cherokee and had to use a case spreader to pull the ring gear carriers out. Bravo!
i used a case spread years ago, also rear end shims for the side gears and cupped ones for the spider gears they were select fit .i don't remember if it was a jag an mg or aston ,it was foreign.
Great video!
Nick,
Consider next time trowing a mag base on and getting a base line for your backlash.
Sometimes I even but some marking compound on, put a little residence on that pinion and roll the the ring gear a few times, just so I get a good idea of what to expect.
Usually if Im trying to go back together with all the same components.
Keep up the great work!!
Nick , just great information and content 👏 👌 👍.....covering the many different parts to work together to go fast .. Great stuff Nick 👏!!!!!!
You need to use a case spreader for disassembly and reassembly.
I'm a Chev guy. Not sure why I just watched a tear down video on a Mopar rear diff, but I did!
Great show Nick as usual,some of it I know some I don't,great source of info guys thanks 😎
Great video, Nick! I have long been a fan of the Dana axles. There's a Dana 44 in the rear of my 79 Jeep CJ5, and a Dana 30 in the front. Such a timeless pieces of engineering artwork. Thanks for doing this great breakdown video!!!!
Very cool!
If you ever have problems getting the bearing races out , weld a bead around the center of the race and when it cools , it will come right out . It shrinks the race !
I'm a certified welder of 40 years . I have my own portable welding service for 35 years and most of that has been working on equipment . This technic works 100% of the time . I learned this through trial and error . It doesn't have to be a pretty bead either lol . Stick or wire will work !
Frigging awesome! Love it! Don't let it go to your head though!
Love these tear down videos. Full of tips from Nick Thank You
good morning nick and George and staff hope all is good for you 👍🇨🇦
Good morning Danoh! Thanks for joining us. ☀️
Another great video i learn so much watching these videos. Nick would make a great Professor like anything else he does he does fantastic.
I love the smell of gear oil in the morning!
Great video Nick .. very informational for viewers who are new at something like this .. you do a great job at explaining…a little side note .. in order to not smell the gear oil…a clothes pin is usefull on the nose… hehe lol 🤣
Basically it's a 3/4 ton truck rear end, our 1972 Ford F-250 3/4 Camper Special pick up had this very exact rear end !
I've got one in a half ton 65 GMC v6.
always pull the oil plug to check condition of oil with Q-tip or water present if third member was out already. in car once had a diff filled with wood chips for gears were pitted so bad from water contamination from a flood
Good morning Nick and crew from mid Tn. I hope everyone has a great day.
A little trick...To keep the axle tubes from turning in the case housing we drilled and taped 3 3/8 inch grade 8 bolts fine thread bolts threw the case housing in 3 different spots on each side. Then install bolts and cut to length then use red loctite to hold them in and keep them from leaking gear oil. You can weld the tubes to the case but it is way to easy to warp the tubes. You can use this trick on any rear end. I have seen my share of tubes twisted and its dam near impossible to fix.
That oops is coming out of your paycheck !!!!! Get the best boots you can Nick !!!! Lol
Dana Axle Corp was in Janesville, WI back in the day 😃 I can almost smell the hypoid gear lube.
Putting one of these in my 87 Monte Carlo!
I just found your channel today, really like the way you show how and why you do what you do!!!
Welcome! Glad you found us.
Just a little condensation from your Canadian temperature fluctuations
Looked clean already.
That's such a better setup than ford or GM where the axle bearings eat up the axles. Nice job you guys!!!
8 and 9 inch Ford have sealed pressed bearings
@@hitekbigmek I’m referring to the 8.8’s and smaller which are in most F150’s and passenger cars
So crazy. My 78 f250 has a Dana 60 w a 4:10 gearing. Center section looks identical. Crazy how everything from those era’s are so identical between makes
Love old school. Now 67 yrs young I had a 1969 Camaro SS 396 CID 375 HP posi traction 4 speed diff was 4/10 gears. What I wouldn’t do to have her back. Original came as yellow with black wide strips. A ripper.
Nice.
In Australia we call it a spanner or open ender Nick..or a nut f....r because it rounds the nuts of if doesn't fit properly.. good show on the Dana 60 mate
دائما مع الجديد شكرا يا خبيرعلى كل هذه التوضحات القيمه
Dana 60 ,best diff of them all. Unfortunately we never had these in our Australian mopars. We had Borg Warner crap so I built a nine inch for it. Sick of blowing up Borg Warner diffs every week.
I love Nicks attitude.. mark it where we can see it. That’s right hahahaha
Gear oil on Nicks boot
- YOU’RE FIRED!
HAPPY THANKSGIVING NICK and crew
Very informative, question for you I think I counted 10 bolts on cover. I have often heard people refer to different diffs by different amount of bolts on cover.
No, not on the Dana 60.. In many cases it is common on the 10, or 12 bolt cover on the Chevies.
Great video Nick and Leo!
Love a Dana!
Hey Nick I know you are busy as two Nicks , but check out Gale Banks vids on differential covers and oil flow and cooling of the differential. Point is, stay with stock cover, or get Bank's cover. No overheating the oil, no aeration either.
NICK,
I LOVE the smell of gear oil, ATF, paint, silicone, chassis lube, gasoline, diesel fuel, ect.
I HATE the smell of perfumes, colongnes, body powders, ect.
!
Legend has it that young man is still removing that pinion race…….