How to fix a bad CV Joint boot - How to repair a hole in your CV Joint Rubber Boot
Вставка
- Опубліковано 8 вер 2024
- How to fix a tear in your CV boot quick and cheap. You might not have to run out and buy and install a new CV boot or replace the entire shaft. This video is about how to fix and extend the life of your CV joint/shaft until you can replace it correctly.
Now before you go crazy with hate comments, remember I said this is a temporary fix until you can get it done correctly.
This LINK takes you to Amazon to buy the part I used, and yes I will make a small commission for you to buy 1 or 2 or 3:
HERE IS THE LINK TO BUY: amzn.to/3DTZaMG
Got something you want me to try out on a future video? Send it to me.
Brian Minson
P.O. Box 992
Higley AZ 85236
idrivea9@yahoo.com
Support us by BUYING A TEE SHIRT!: teespring.com/...
Pateron: / brianminson
Facebook: / brianminsonphoto
Instagram: / brianminson
Twitter: / porschebran
#cvbootrepair #ad #cvbootfix
(This video is about: how to fix a torn cv boot,cv boot is torn,replacing half shaft,cv,cv boot,half shaft,cv joint,cv boot repair,axle boot,cv boot replacement,cv joint boot replacement,cv axle,cv boot clamp tool,cv boot banding tool,cv boot repair kit,honda cv boot,toyota cv boot,nissan cv boot,ford cv boot,chevy cv boot,vw cv boot,dodge cv boot,how to,how to replace cv boot,how to replace cv boot without removing axle)
WOW ! What a HACK Fix ! damn~~~ NOT on my Porsche~~ you're right, it is a band aid fix.. So glad you prefaced that..
LOL agree my Porsche gets new stuff LOL but the ole Honda daily gets hack jobs till it gets picked up for scrap lol
I would have trimmed the front of that boot before gluing. Needed a better fit.
Ive used splitboots b4 with good success...they Do work ..How well they hold up is Critically dependent on getting them around the sharft and completely gluing that seam while not getting Any grease whatsoever on the seam that is to be joined... easier said than done! B4 I ven attempt to insert the immaculate cv boot around the shaft, I pack it with new grease, use clear saran wrap to then completely wrap the shaft and the end with the new grease so that Any exposed surface that the new boot will touch, is grease free, uncontaminated... then slip the boot over the shaft and start with the gluing.. when the seam is completely done and cured, Only then remove the wrap and slide the boot on...some boots are in 2 halves, others have only 1 seam.. if working with the 2 halves type, I glue one half of it when off then car, then u only have to deal with gluing 1 remaining side when on the axle...
if you keep things Hospital immaculate in regards to the seams, it Will hold up great..the halves literally Fuse together... If there is even a trace of grease touching the seam, it the glue may seem to work initially,but it craetes a weak spot that Will let go in that spot later down the line.
i would have cleaned all the grease off the shaft, cut of the lower bit of the boot, glued it around the shaft, then moved t up to bearing and packed with grease
That’s a great idea! Thanks for sharing!!!
Temporary fix at best in the UK we use stretch boots either using a cone or the pro-level tool a boot expander
Great job, but flex tape or spray flex seal or bigger boot will do even better. But great idea that you provided
That's a great idea, thanks for sharing!
I would be less worried about grease coming out than grit getting in. Depending upon the car, the axles are inexpensive. Even for my Porsche, I got a "preowed" one for like $90 delivered. In my case, there was other (dealer caused) damage, but the price and ease of repair remains on the whole axle.
Fair attempt at installing a split boot. But, wouldn’t it have been easier to do with the wheel off? Can you give an update on how those boots have held up and time on vehicle? IMO, the area with the broken boot should have been thoroughly cleansed of the old grease including the shaft. Then dry fit the boot to ensure proper fit. Mark area/s if any to be cut off allowing for a few mm over the cut area. Once completed, apply the sealer from the smaller end working to the larger, but doing in small steps and holding the part together for the requisite time, little longer is better until completed. After,then go ahead and pack grease into the cv axle and any balance into the boot. Complete by clamping both ends with provided straps. Ensure you have a tool that will compress those clamps to begin with. What tool did you use to clamp as it appears to need a specialty tool for that type of clamp?
I used a pair of squarenose pliers to get the ring to snap together.
Very helpful!
Hello and thank you for the video. Can you give us an update please
Ware. You. Can. Get. This. Cvjoin. Boots. The. Sale. On. U.s.a. ?????
What about the outer boot?
That boot was in good shape.
But mine isnt
Ephesians 5:4 in the Bible: nor should there be obscenity, foolish talk or coarse joking which are out of place, but rather thanksgiving
“See, the day of the Lord is coming - a cruel day, with wrath and fierce anger. . . . I will put an end to the arrogance of the haughty. . . . Their infants will be dashed to pieces before their eyes; their houses will be looted and their wives violated.” (Isaiah 13:9-16 NIV)
let's turn to God Shepherd's Chapel UA-cam explains the whole Bible God bless
Thank you for saying hi!
John 3:3 in the Bible: Jesus replied, very truly I tell you, no one can enter the kingdom of God unless they are born again
Am I get an amen up in here!?!?!?
En España por favor