UPDATE: I finally got to use the Arbor Press with the metal stamping tool! OMG! This is wonderful! I'm so glad for the internet! I honestly cannot wait to use it again. It wasn't as hard on my wrist as the banging of a hammer was before (it didn't help the carpal tunnel either). :) Thanks for creating this tool! :)
Thank you for the video. Personally, I would use an x-y vise, which can be picked up for like $50. Then you can just move it along in a line perfectly and get your letters in a straight line without a piece of tape.
Is that the 1 ton Arbour press? I'm looking to buy a press and have been looking at the 1 ton ones. I'd like to get one of those stamp attachments if the attachments will fit the 1 ton Arbour press. But not if it's a different one.
The purchase of an insert is required when buying the attachment, but to use a 1" stamp you would insert the stamp into the attachment without an insert.
Thank you for the video. You are correct, before you start stamping you need to but these. Where can I purchase these attachments? Will they work with Beaducaton design stamps?
hi, for those of you that use a 1/2 ton arbor press... what ga metal do you use with it? i bought one and a few design stamps a month ago, and i tried using 24ga dead stof sterling silver, nothing transfered, so i went to 26ga, and i got a little impression and a better one after i used a hammer on the ram, which i dont want to do. i thought i would just have to pull the handle down and then my design would be on the metal? maybe im just really weak? i just ordered 28ga but am worried that might be too thin. i can never get the full design when i hand stam, i've tried the tilt n tap but always mess it up. letter stamps,numbers and simple designs i have no problem free handing on metals up to 24ga.
@@FlatwearableArtisanJewelry thank you i will try that. i also tried lowering the press because i had it on my kitchen island, i think if i put it on a lower table or something i will get more leverage.
I bought the tools and a one ton Arbor Press. My stamps fit but I am only getting a partial stamp. I am practicing on copper but want to stamp silver. On one You tube a guy is hitting the top of the shank but you are not. Should I be able to just press the stamp? I feel Ike I’m pressing hard. Please advise.
I am so happy to see this video because it gives a lot more information on how to use the metal stamping tool. This is super helpful!
UPDATE: I finally got to use the Arbor Press with the metal stamping tool! OMG! This is wonderful! I'm so glad for the internet! I honestly cannot wait to use it again. It wasn't as hard on my wrist as the banging of a hammer was before (it didn't help the carpal tunnel either). :) Thanks for creating this tool! :)
Thanks for considering making the video- I was lost and discourage- I have B insert.
Thank you for the video. Personally, I would use an x-y vise, which can be picked up for like $50. Then you can just move it along in a line perfectly and get your letters in a straight line without a piece of tape.
Is that the 1 ton Arbour press? I'm looking to buy a press and have been looking at the 1 ton ones. I'd like to get one of those stamp attachments if the attachments will fit the 1 ton Arbour press. But not if it's a different one.
Can you use this stamoing toll on a ring that's already formed? Thx!
Do the weight lock on when pressing items
I have not found the link under the video from your shop. Can you please tell me, where I can order the tool?
whats a millimeter?
I have a one inch stamp, would I just buy the metal stamping tool attachment? Or how do I use a 1 inch stamp?
🔥🦈🌊
The purchase of an insert is required when buying the attachment, but to use a 1" stamp you would insert the stamp into the attachment without an insert.
I have already an arbor press (Eurpean type).
The shaft is 24x24mm( a little less than 1"x1"). Would it fit with your attachments?
yes
Thank you for the video. You are correct, before you start stamping you need to but these. Where can I purchase these attachments? Will they work with Beaducaton design stamps?
They will work with any stamps that are sized for the inserts.
I ordered them, how long is shipping?
@@FlatwearableArtisanJewelry where do you find inserts?
hi, for those of you that use a 1/2 ton arbor press...
what ga metal do you use with it?
i bought one and a few design stamps a month ago, and i tried using 24ga dead stof sterling silver, nothing transfered, so i went to 26ga, and i got a little impression and a better one after i used a hammer on the ram, which i dont want to do. i thought i would just have to pull the handle down and then my design would be on the metal? maybe im just really weak? i just ordered 28ga but am worried that might be too thin.
i can never get the full design when i hand stam, i've tried the tilt n tap but always mess it up. letter stamps,numbers and simple designs i have no problem free handing on metals up to 24ga.
What surface are you using to stamp against?
@@FlatwearableArtisanJewelry a steel block.
@@shaunasilver9545 You should be getting an impression but your metal is also pretty thin. I would suggest going down to 20 gauge or thicker
@@FlatwearableArtisanJewelry thank you i will try that. i also tried lowering the press because i had it on my kitchen island, i think if i put it on a lower table or something i will get more leverage.
Link seems to be broken.
Do you need to put rubber under your press like when stamping by hand?
no
Do you have to special order attachments or do you have a store that sells them?
You can purchase them at the link in the description box.
I bought the tools and a one ton Arbor Press. My stamps fit but I am only getting a partial stamp. I am practicing on copper but want to stamp silver. On one You tube a guy is hitting the top of the shank but you are not. Should I be able to just press the stamp? I feel Ike I’m pressing hard. Please advise.
The best impressions come from stamping on top of a steel bench block. www.flatwearable.net/home/metal-stamping-tool/
the link to get the inserts and attachments doesn't work. Where can I find this? Thanks
www.flatwearable.net/home/metal-stamping-tool/
Hi... where do I purchase the pieces for the stamps. Thanks
Here,. www.flatwearable.net/home/metal-stamping-tool/
I found the machine but not attachments , OMG ! Where did y'all get it?!?? Driving me crazy 😜.
The web address is under the video.
Flatwearable Artisan Jewelry are the attachments still available?
I don’t see a link and I can’t find these on google search! Help!?!?
www.flatwearable.net/home/metal-stamping-tool/
Where do you buy A , B and holder parts at ? Ty
www.flatwearable.net/home/metal-stamping-tool/
Here is the link to where you can buy all these items. She also has stamps. www.flatwearable.net/home/metal-stamping-tool/
Link to purchase doesn’t work anymore. Is the attachment still available?
www.flatwearable.net/home/metal-stamping-tool/
Set up a fence
How did you flatten the spoon?
A rubber mallet
May I ask - what Male is your press?
Harbor Freight
I would love to purchase the tool and inserts. Please tell me how. Thank you.
The address is under the video
Thank you so much. Just placed my order. Really looking forward to having these.
@@pammiepiehoney Harbor Freight have it for $60
How can I buy this? The link no longer works
www.flatwearable.net/home/metal-stamping-tool/
Where do I get that attachment channel?
Check the link in the description box below the video.
Where can I get these pieces?
www.flatwearable.net/home/metal-stamping-tool/
Where can I purchase that from please
www.flatwearable.net/home/metal-stamping-tool/
Are these still available?
www.flatwearable.net/home/metal-stamping-tool/
Purchase this where ?
The link is under the video in the description box