Just checked out the Arcimoto. Looks pretty incredible, congratulations! And thank you so much for the compliment! Means a lot, coming from you! Cheers!
Castor and Camber work in tandem. As you have observed, a lot of caster will make your bike stable at speed but when riding slow, it tends to 'fall' into the curve. This is because as you turn the wheels, the frame of the bike moves lower. Therefore the weight of the bike acts as a force that wants to increase steer angle. Camber has the opposite effect, when you steer away from straight, camber will lift your bike (with 0° caster) . Therefore the weight will always push it back to its lowest position, which is going straight. By choosing caster, you can control high speed stability, by matching camber you can restore / adjust low speed stability. Toe at 0° is usally for best efficiency, which i guess is most important in bikes. If your ball joints do have a little play toe out / toe in will put preload on them and they wont flop around all the time. This preload techinque is also used because ball joints have a reduced livetime if the direction of force does change often. This may be irrelevant on a bike that does a lot less miles and is way lighter. As a rule of thumb, 20° caster is already unuasally high and compensation by camber will not work perfectly anymore. typ. is 5-15° in the applications i know Another factor you havent touched on is the length of the control arms. Usually, the lower arm is longer than the upper arm. This gives the effect off added camber when the suspension is compressed. One reason for this is to eliminate tire scrub when going over bumps, the other reason i believe is added stability when carrying heavy cargo. This may also be a reason why lengthening your lower control arm for added camber gave you such benefits. However it can also be done by moving the frame mounting of the upper control arm further outside. And when changing suspension geometry, always check that the sterring rods and their joints are still correctly spaced in the plane of the other joints, otherwise you will introduce bump steer. Bump steer is when compressing the suspension changes toe. Very cool project of yours and i completely understand that a test must be reduced to some variables, thank you for the work you put into this experiment!
Uauu, thank you for the explanations on the impact of geometries and the relations with each other. I hope others interested in the geometry go ahead and read the comments. There is just so much juice in them! Truly appreciate it. I'll just confirm that the lower wishbone is longer tan the upper, designed to have zero scrub radius. And that I compensated the spacing of the steering arms with that T in the front steering pivot. I did have bump steer before this part but not anymore. Thank you so much!
Exactly, I was going to post the same thing. It is also true that if you have power steering, you don't have to even know its is harder to turn. I build r/c cars, it all done by electronics, not human.
Brilliant comment. Thanks for the benefit of your expertise and clear language. There’s so many variables at play and so much fabrication involved in arriving at a working prototype. I wonder if a simplified 3d model could be 3d printed desktop size to study the tilting and turning geometry. Then visualizing the things you describe would be easier. What an amazing engineering design tool that would be and it would be fun to have a toy sized version on one’s desk. Tilting tadpole cargo bikes and recumbent HPV nerds would line up to see their design notions take shape before all the expense of cutting metal.
@@ciberbri59 totally agree on trying out things with reduced 3D printed models. Actually, this is precisely how I started this project: ua-cam.com/video/UylIv7d50uQ/v-deo.htmlsi=IRATRP0ND4vPwmU2. Cheers!
I agree. This was very useful. I've been working on something similar and my biggest problem has been steering and the other is I want to make mine all wheel drive and put hub motors in the front wheels, but then because of the Ackerman principle the motors would have to drive at different speeds when turning...and its a little bit too much software for me. So if you ever get there please make another video 😁
@@rogerdueck9725, thank you! Ya, now we start to see some cars with electronic differential. Even with two motors in the rear wheels such as the new Tesla Model S and X Plaid and Rivian trucks. But I agree that it's quite complex. Cheers!
@@pedro-nevesThankyou for this video and your video of your build. These titling cargo bikes have always impressed me and seeing your videos about how it works was great!!! Have you seen the ili cargo bikes, they have some interesting tilting bikes, it might give you some inputs for future developments, thanks again it's inspiring to see people like you create cool products in your own back yard
Tadpole cargo trikes make the most sense: - two tyre contacts in the front - redundant front brakes - can use a tilt-lock - retains the simplicity of a single rear wheel Love it! P.S. : there are similar trikes called "HNF Nicolai CD1" and "Mäx & Mäleon" You could look up what values they used as a reference.
Hello, thank you for that! I agree with the advantages that you mention. I have actually tried a Nicolai once and thought it was incredibly cool and I watched a few videos with the "Mäx & Mäleon" which also looks cool. Cheers!
@@tonicedeno, Hello, one small correction - I believe the Black Iron Horse is from Denmark. And, I tried one with rear steering and I liked it very much! To be hones, I think it's the best I ever tried for slow maneuvering. The reason why I chose the front tilting to develop is because I like more how it rides. With front tilting, it rides fast better (more like a bike). Cheers!
I knew a genius fabricator who created a 4 wheel mountain bike with a roll cage body and I followed him at 50 mph on the first run at Plattekill where we were downhill racers. anyway. his toe-in was about 1 degree and camber was about 7 degrees. His vehicle had a solid rear axle so he could use the inside rear wheel to friction brake in sweeping turns. It was awesome to behold
I'm not sure if anyone else did but I found this useful to understand what toe, camber and castor means and now I plan on using this information to make better tunes in Forza horizon 5. Had the general idea on camber but visualizing it helps a whole lot more. Thanks.
@@pedro-neves Hey, now that you know the optimal angle for the wheel alignment, would you consider removing the adjustable part in the center to shed weight and make the assemble more simplified?
@@S-I-R-E absolutely. I'm already working on the new design. Removing the adjustable parts will allow shedding weight and also package the whole suspension and steering a little bit better. Cheers!
This has to be one of the best cargo bike builds on YT. Well done Pedro. I have thought about building a3 wheeler so many times, but I have been riding a 2 wheel 8freight for years and for me the benefits of 2 wheels on the infrastructure in the uk outweigh the benefits of 3 wheels. But I would still love to build one like yours.
That is very kind, thank you;) I also love bikes and cargo bikes and see advantages in them. But one thing is fore sure - trikes are more fun to build;) In case you're interested I did a comparison once: ua-cam.com/video/uW5teIGglsE/v-deo.htmlsi=ozGWutrevJbW14d5. Cheers!
Hi Pedro, well done. Nice piece of work. As regards Toe, I would suggest 0deg. In cars they sometimes set a toe that allows for the flexure of the rubber bushes so that the end result ubder load is 0deg. 0deg is minimum scrub so maximum tyre life and minimum drag. As regards castor, you are altering trail (the distance between the steering axis intersection with the road to the tyre intersection) as well. Increasing trail will make the steering a bit heavier, decreasing trail will make it twitchier. It also means that in transferring your results to a larger wheel (if you did that) may alter the optimum. For the ball joints binding I suggest putting a bend in the arms so that the ball joint is at 90deg to the steering axis to even out the play in the 2 directions so lean-ability is maximum. Finally, neg camber will wear the tyres on one side. So from time to time swap the tyres left to right and vice-versa to get best life out of them. Doing away with your castor plates will let you shorten it a bit without affeting your load bed. Finally, if you had a lean lock, that would be handy when you have to stop for junctions, traffic lights (both feet on the pedals) and parking. It may also help balance on really steep hills. You could delete the side stand too. Lovely job, I look forward to the next part.
Thank you very much for the kind comment and comprehensive set of guidance! - Understood regarding Toe and Castor! - For the ball joints, I plan to do just what you mentioned - design the angle into the knuckle instead of letting the ball joint handle it. Totally agree with getting rid of the side stand;) Cheers! Have a good time!
Hello! Engineer here :) Nice to see that this idea keep moving these days. I have done a lot of leaning trikes with motor. Let me share some insights? First one - consider a Roll center. Surprisingly, but CG for Leaning trikes must be at groung level instead of over it like a car design. Thats why you struggling with balance while ride without hands. The second - Ackerman angle: Try to decrease amount of it because : A. slip angle of tyre, B. tyre works on a sidewall while leaning and you get camberthrust. And last one. Due to long base your front (air) spring too stiff so it would be harsh with strait (especially at high speed).. (and.. front wheel pressure. IDK but there might be 30-50% lower than ordinary bike)
Hello, thank you so much for sharing your insights! They help me to improve! - I definitely intend to lower center of gravity. - Ackerman took a lot of work. I started with the "designed" geometry and then did adjustments until I feel that there's no rub. There are a few things to fix for sure. I'll consider camberthrust, thank you for that! - Ya, I agree that spring air pressure and tire air pressure contribute to stability. As it is, when I load it with 45 kg, the shock contracts about 1/3 of its range. Cheers!
@@federicoromero6130 Oh! Thank you! Youre right. I mean RC. Roll Center. Of course CG located way up from the ground. But Roll Center must be located at the floor, and imitate front wheel of regular 2 wheeled bike. In other cases 3 wheeled leaning trike hard to drive. Rider feels instability. It looks like front wheel start to slide from side to side.
Toe is important when you have 2 wheels. If you want to travel in a straight line. Uneven roads will cause the bike to pull as will suspension travel and as someone said camber is involved too. How does the bike handle bumps or gutters when one wheel is not on flat road?
The corect turn geometry is the one that when turning, the projections of the two wheel angles alyways cross in the extension of the back axel. Toe mostly used on cars to enhance break and acceleration performance, and fix changes of geometry on wide wheels. Usually, for the geometry and handling toe-out is what you want. It may help tweak the lost of handling from caster. Maybe 6/5 degrees is too much for toe.
Thank you very much for helping to understand Toe a little bit better. I start to comprehend it! I hope it's also useful to others reading your very nice comment.
I'm not engineer but having a good feel with technical stuff my opinion is that if camber no toe,it is one or the other,both is too chaotic for a smooth ride and you actually already proove that camber is usefull to add. Congrat for your patience!!and thanks,this was great and really usefull for the community.Ps you gave me some more reasons to make mine!!Thanks again Pedro.
Nice project thanks for sharing. Any Camber will "work the spokes" as the wheel rotates, i.e. the load in the spokes will go positive and negative with each rotation of the wheel. Athletic Wheel chairs with camber have problems with spokes loosening.
Hello, thank you for that! Indeed, I was not thinking of negative effects of camber, but now I see that there will be extra strain on the spokes and bearings. I think I will still live a bit (1-2 deg) but definitely not 6 deg. Cheers!
A mechanic once explained to me that toe-in gives very little real benefit to steering or stability, but that exactly 0 toe is very hard to maintain and even slight toe-out has a very negative effect on steering. Therefore slight toe-in gives a slight safety advantage. Really enjoyed this video and your process!
When we visited Amsterdam, I amazed by the cargo bikes that I saw there and been meaning to fabricate one similar to what I saw there. Yours is a bit more complex for me ahaha but by seeing this build, it gives me motivation to go ahead with my project...
Hi Pedro, You are an inspiration to all! Hats off to you for your build! I would love to see if 5 degree caster is any better with negative camber you have set. I know your bolt locations do not allow this, but since you are going to alter the build, maybe you can try this on the old build before committing to the new design. I would bet that you would enjoy the additional manoeuvrability without sacrificing much stability. As you described you can add electric motors. I don't know if your ultimate purpose is more geared towards heavier cargo or not, but it seems like you would be ok with a pedal assist system given your location is mostly flat. You could try front wheel drive, (would be a quite a bit more complex as you need to control the speed based on many parameters, steering angle, tilt etc.) or even all wheel drive (but it seems like you wouldn't need this). If you are making the new one from scratch, you can also try to use a more optimized design for the rider frame. Most of the frame geometry is overengineered for the loads you have it seems, you can potentially cut back on weight there a little bit. If you design the entire linkage including ball joint with camber and caster settings you have in mind you will enjoy a better ride and longevity. I would advise against toe due to fact that your vehicle is tilting and thus no need for "correcting" steering dynamics due to weight and contact patch distribution is needed. With toe you will get added wear on tyres (negligible if you don't use very soft tyres) and most importantly additional effort is required to energy dissipated as heat with geometry causing shearing on contact patch. In terms of handling feel theory suggests that toe out will make it more "twitchy", in non-tilting vehicles a little toe-in goes a long way for responsiveness but has some costs for high-speed stability. In your case the effect at such small angles is negligible as you have tilting. If you drive front wheels with motors, then you might want to consider toe-in for added traction, but again using ESC to control torque would be the better option. I appreciate the knowledge you have shared and hope to make use of this for myself in the future.
Thank you so much for your kind comment and contributions to knowledge sharing! Indeed, I am left with the question of exactly how much caster;) I only know that 10 is better than 0 and better than 20. I already have an electric kit with motor in the rear wheel to install. This has the advantage of being a very simple installation, and I can continue the development and tests and ride more distance without becoming so tired. At the same time, I am starting the project of developing an electric mid-drive with gearbox. I'm also excited about this project;) I will redesign for fixed linkages and for the correct angles between knuckles and ball joints. I have learned a lot about Toe since I published this video;) it’s incredibly cool how much knowledge people are happy to give. Thank you. I also appreciate the knowledge that you shared and makes me happy that you find use in the knowledge that I shared. Cheers!
Love this research and content - thanks for taking the time and extra effort in making an adjustable config so you can test different options. I've wondered about a cofiguration where as you are initially turning, the bike is more resistant to the action, as a way to improve stability riding in a straight line.. then as you lean into the turn, you're essentially confirming to the bike that are are actually trying to turn, and the turn gets easier as you commit. Added bonus to this is that it also would prefer to return back to straight riding at the end of the turn
Thank you so much for your kind comment! I love to create and share knowledge. Let me tell you that I once did an experiment - locked the tilting to see if I liked how it rides. I didn't, either in straight line or in turns. It becomes a totally different vehicle (more like a quad) and I don't like quads... The free tilting mechanism gives the vehicle a sense of riding like a bike, which I like, with the added safety of two wheels in the front. I know that this is not the same as you proposed but gives a little bit of insight. Cheers!
Just stumbled across this video, what a great project. I live in CPH and have tried many different 3 wheel cargo bikes, currently with the Butchers and Bicycles trike for family duties. I have to say the tilting trike is a the best solution that I have tried, on the Butchers the main drawbacks are related to the room the wishbones are taking up from the passenger/Cargo box, and the fact that the ‘cargo’ weight is also positioned directly over the wheel axle, if I put an adult in the box hard braking and that weight shift makes the bike pretty unstable, your solution is definitely getting around that. Also, from experience it can be pretty disconcerting to run out of ‘lean’ when committed to a corner.
Hello, thank you very much! I also like the tilting solution. For me, it's the type of trike that gives the best riding experience. Interesting that you're saying that you experienced running out of l lean when riding. I thought this was a problem just with my design. I know how I will improve it, but not eliminate the issue totally because of the limits of the ball joints. Thank you for those descriptions of riding your trike! Really helps to consider pros and cons of design. Cheers!
XLnt testing! i have a few recumbent e-bikes and trikes and lately bought an e-Heisenberg secondhand. it stays, always pleasant to feel the different geometries when you ride one.
Another piece of the geometry you can change to achieve Ackerman is the tie rod connection point on the steering knuckles. Move the tie rod connection points inboard. This will turn the inboard wheel more relative to the outboard wheel. You mentioned moving the steering arm forward. I interpreted your statement as moving the whole assembly forward. You could just rotate the arm around so the connection point is forward of the pivot point. But this would require crossing the arm from the handle bars. I’m familiar with setting this up in four wheel vehicles. Requires some shifting in thinking to do it on a bike. For what my opinion is worth, I also don’t like the idea of camber on bicycle wheels. They don’t deal with side loads very well. I’d try to keep the wheel aligned with the resultant load. But you probably know that already.
Thank you so much for that! Indeed, it's been a big debate about what moves where in the steering. I'm now designing a new vehicle and haven't decided because some decisions get in the way of others, of course. But I understand what you are saying. Regarding camber, also after some comments such as yours, I'm now almost sure that it will not have any camber. I appreciate very much the constructive suggestions. Cheers!
Wow, what an extraordinary project. I ride an ICE recumbent e-trike. Me and the trike are a little lighter than your setup, and there are a lot more spokes on the front wheels. But even then I'll break one every so often. So I would agree with you, more spokes! I run drum brakes up front, so no hydraulic maintenance, and I really like the progressive feel. Perfect for tadpoles. Anyway, good luck with what you are doing, you are obviously a brilliant young man.
Thank you so much for your kind comment! I'm working on stronger wheels with 28 spokes (and different hubs). I'm also working on making it lighter (next frame will be made of aluminum). I love that there is a community of tadpole lovers! Cheers!
This was a fun exploration of the math behind steering geometry. You might further refine results with rake & trail adjustment to bias tandem tires load vs single steer on the front axle, maybe even with torque bias observations for left vs right steering effort with your current weight distributions. Thanks for sharing.
Thank you very much! Indeed these tests gave some insight into the ballpark of geometries but there is so much to find out. The next design will already have plenty of improvements. In the future, I'm considering to build a computer model for simulation. Cheers!
Hello Pedro. For Ackerman steering. Draw a triangle from the middle of the rear axle to the steering pivot point on each front wheel assembly. Your steering rack links to the front assemblies on this tapering triangle. Then you won't need that strange double bracket at the steering input. I hope I have explained well enough. Please let me know. Also very well thought out testing procedures.
Hello, thank you very much! I think I understand your guidance. But, the double bracket at the steering input is used to eliminate bump steer. If I didn't understand correctly, is there a chance you could send me a rough drawing to pncnveves@hotmail.com ?;). I understand if you don't want to go to the trouble of sending drawings. But experience has taught me that community comments are of incredible value, so I chose to explore;) Cheers!
@@stevedobbsphoto, I'm so sorry, there was a typo in the email.:( Here is the correct one: "pncneves@hotmail.com". Thank you very much for your effort!! I tested the spelling to make sure I'm not wasting your time.
Riding ‘no hands’ is how I confirm proper geometry. I am not happy with a bike until I can control it coasting by weight shifting alone. I never built a tilting trike but it is in my project list, and your work is going to make it easier. Thanks a lot.
Congrats on hitting such a milestone! Designing things is always such an interative process that takes patience and dedication. Your hard work and perspective are inspiring!
Thank you so much! I'm really happy that it's great to ride now and still having so many improvements ahead;) I'm super happy that this serves as inspiration! Thank you for saying that;)
Very excellent design video, I really enjoyed it and I learned a few good to know things before I start making an inverted trike motorcycle! It will be interesting to see how much I need to scale everything up.
Thank you very much! It's motivating to do more with such kind comments;) In the next video, I'll install an electric conversion kit, which will enable me to ride more distances with and without cargo. After that, there will be big changes. I will organize this into a project where everything has drawings and versions, and it will be easy for anyone who wants to use the drawings. Cheers!
Thank you! Indeed, I already made an electric conversion. You are welcome to check it out here: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=dzjplPb94CF0m3Rw. Cheers!
Beautiful ! Suddenly I know more about the geometriproblems. Thank you and good luck with the electric conversion, 10 kilos of extra muscles will make this a vehicle for the future city traveller. Perhaps a tentlike cabin for kids as the next project. I had theese thoughts myself 40 years ago, right idea wrong timing in my case.
Thank you for the kind comment;) And I'm glad that this helped you understand the geometry. This was the main intention with this video! Indeed, it needs to be electric. I've been working on a conversion and testing, and I'm almost ready to publish the video about that. And I agree with the tent! I look forward to it being good enough to carry people. Cheers!
The Ackermann steering problem you have is caused by the (reversed) T-shape articulated connection. To obtain a symmetric turning radius, you need to use an I-shape, where both wheels extension arms are connected above each other (at the I-bottom articulated connection). Also as you noticed; the 20° caster inclination on the central turntable making the steering stiffer is practically better applicable for high speed. Once you have the electrical version going high speeds, try to invent a caster central turntable that automatically adjust the inclination on the angle from 10° to 30°, as speed goes higher. If you manage to develop such a functioning system, you can patent it straight away!
Hello, and thank you very much for sharing ideas and tips! Indeed, the T-shape connection complicates the Ackerman. The reason why it's there is to mitigate bump steer. Regarding caster, I never thought of having it moving depending on speed;) that sounds pretty cool actually;) Cheers!
@@pedro-neves ...as to the front wheel rotating Caster holder, it is indeed a mechanical surrogate for the hydraulic steering wheel system of most sport cars that automatically stiffens with high speed. All you need is to install a small electric motor, attached to a speedometer that rotates the Caster between 10° and 30° for speed up to 60 Kmh. In fact, I have never seen that system implemented in Bikes before, so check it out and make some researches to be sure if it is a novelty. Once you have a working prototype, patent it asap! If later this patent proves to be profitable, pls do not forget my reward! 🥳 Beyond that, I have a good, revolutionary transformer bicycle draft, but unfortunately no workshop like yours to realize it. Greetings from Berlin.
@@Big_Bang_Bong thank you very much for your tips! My approach with this project is to make things open source (the beginning of the next build will have drawings shared in editable format) in an attempt of us all learning together. If you're looking for a place to work - I don't know Berlin, but I would imagine that it's possible to find a community workshop. Here's an example of how it works in Amsterdam. Maybe it will give you some inspiration: openbarewerkplaats.nl/. Cheers!
You do want a small amount of tow in. It's hard to reproduce on demand but if you have zero tow, you can get a little shimmy in your wheels if there is even a little play in any of the mechanism. A small amount of tow in will prevent that, I don't think you need any more than 1 degree, 1/2 degree may be enough. You don't want to go too far because it will cause excessive tire wear.
Very cool, Pedro. Love it. I think tilting trikes are the way of the future, (until we can just fly everywhere). Your idea of adjustable linkages is inspiring. My mind goes to variable linkages, using linear actuators, or cable levers, so that all could be adjusted on the fly. Cargo, no cargo. Hi speed, low speed etc.
Thank you very much! Well, the next one will have cable steering;) maybe not exactly what you are thinking of but still an interesting feature, I think;) Cheers!
Nice video and presentation. Positive trail length will induce a negative camber angle in proportional to the steered angle for balancing stability. Having a constant camber angle is a different issue.
¡¡Hola, Pedro!! Following your progress has been fantastic! Thank you for taking so much time/effort to distill and present it here for all interested to learn from and enjoy. Your video production improves and improves, and that takes much effort and talent! You are certainly inspiring me and sparking/filling my noggin with new ideas. Love it!! It seems that a close to neutral toe is optimal for your design. More toe-in, or toe-out, would cause increased tire friction/scrubbing and wear, and add to your pedaling efforts. No es bueno. Since our human body is relatively meager in terms of power output, we are pretty sensitive to additional load increases or decreases. I do like how you gave several of the configuration ~2 days of trial. Riding different bikes/configurations may preemptively feel "wrong", but our body/brain adapts quickly and then we, as you were, are able to make better comparisons. Also, if you had simply made a trike, with no suspension, bleccchhhhh! Vehicles like that become "dynamically dead" and it becomes far removed from the fun experience of a bicycle. Your front suspension definitely IMPROVES upon that!!! Now you have a beautifully unique tri-wheeled bicycle. As for tools, have you improved and/or gathered new ones? Got a small (they can definitely fit your needs) TIG machine? It would be nice to see some 4130 chromoly tubing in the front, lighter AND stronger for a future iteration. Then you could refit that on a future, lighter rear end. A rear end that will maybe have a 7-speed gear cluster that would always be there and NEVER need an electrical outlet. Oh, and straight handlebars are okay for aesthetics, but suck-suck for ergonomics. Hold your hands out forward, loosely, in front of you, grabbing an imaginary handlebar, and your hands grip at a natural ~12-15deg bend. In the future, consider that. Your elbows and shoulders will thank you! LOL And, THANKS as well for speaking to us in completely intelligible English! You communicate excellently! Because of that your video is completely accessible to me. Lucky me. You made me smile when you spoke of how you felt after all you have done to achieve your ride/design to this point. What you have done, in terms of creativity, is NO DIFFERENT than a fine artist who applies oils to a canvas. To think otherwise is simple arrogance or ignorance. Maybe big dashes of both! I REALLY like your creativity because its product is functional. It interacts with your entirety as you interact with it. AND, of course, in its essence, it is a bicycle. A beautiful bicycle. Lastly, tip 'o the hat, and two thumbs up, to your camera dude/chic!!! Your video was greatly improved by their assistance. Please, pass my "THANK YOU!" to them as well. I am only more excited for that day in the future when you share with us again... PS Straighten out the nose of your saddle. I'm picky that way. LOL
Uauu, I wish I could put more than just one heart in this incredibly kind comment;) Thank you so much! I aim to improve the video production every time. I always have some notes of things to do a little bit better. I aim to share knowledge and inspire others to build. Hopefully, adding something of positive. It is very inspiring to me to read from you that you are inspired;) I definitely agree that the body adapts. One interesting thing that I noted is: after you change, it feels worse, then after some time, it does not feel worse. Then you change it back to what it was, and it feels so much better! That's how you're sure that it was worse;) This is much more fun to ride than a fixed trike for sure!;) For my next project that needs some welding, I will definitely get a TIG machine. Not just because the welding process is cleaner and quieter but also I cannot express how much I have been grinding to clean the welds!... Oh... Regarding electric power and gearbox - Well, soon I will start a project of developing an electric mid-drive unit with gearbox. I think this is the future. I'm inspired by the work of Pinion. I will use a bike for developing the mid-drive and in the meantime I will install wheel motor in the cargo trike to help me with carrying cargo around;) As for the handlebars, hehe, well, I have to say that I had different handlebars in this vehicle already. I think that the MTB lover in me ends up trying to make a cargo vehicle like an MTB... If I'm really honest, I have to admit that I aim to make this cargo trike so good that I will ride it on an MTB track and jump with it. Then I'll know it's good;) I'm glad that my spoken English is well understandable. That's important for sharing knowledge so thank you for mentioning it! I'm from Portugal so, as soon as UA-cam releases to me the feature of allowing multiple audio languages, I will also dub the films in Portuguese. Aah, your comment on creativity is so kind... Kindness improves the world. The camera chic has just read your comment and has a warm heart as well;) It has been a big contribution from her, improving how to film and doing it in the cold and rain. We love doing it but a comment like yours just makes us love it more. So THANK YOU to you too! I am one of those that has so many project in a queue!... So will definitely make more and share. Many things to improve in the trike (I'm working on wheel hubs in the present), electric mid-drive with gearbox and a whole series about EV charging where I have professional expertise (I will teach how to make a super simple charging station, etc...) Hehe, that saddle is in bad shape actually;) Cheers! Have a great time!
Indeed, I agree. The reason why I compared big differences was to amplify the effect of the change so that I feel what it does. And also to find out the ballpark of where it should be. Cheers!
Ackerman's principle is measured with the steering wheel straight head, not at lock. That's how the geometry of different steering wheel radiius are followed. If you draw a triangle between both front steering axis (at hub level?) and the centre of the rear axle line, that's the line your steering knuckles should be. It kinda looks like your front wheels are a little parralel. At full lock, they should look like they point in a visiblely different direction.
Hi, thanks for that. Indeed, I did not calculate the Ackerman correctly. But, then with small adjustments, I reached there. The outer wheel turns less than the inner wheel and I have no scrubbing. Cheers!
that's a lot of intertwined variables - thanks for sharing! nice suspension but gads ... that's gotta multiply the variables too - keen to watch you iterate!
@@JoshuaRobertPreston indeed many variables;) I'm working on the next one and I think it's becoming so much better than this one already. Thank you for your kind words! Cheers!
Very nice Pedro. You might want to consider the 1 degree toe-in when you add brakes to the equation. Braking force will force the wheels back and create a somewhat unstable situation due to toe-out. I've tested this on my first prototype (way to heavy in the end) and found braking and steering at the same time to be more stable. This wasn't a tilting trike though, but a rigid one with 8 inch front wheels and drum brakes all around Looking forward to the improvements! Pjotr (Tesla Tilburg)
Pjotr! Uauu! I hope you are doing well;) And thank you for the comprehensive comment about Toe. I start to understand that it's important for braking and accelerating (things that I barely have at this point;)) Cheers! All the best happiness to you!
Thank you very much! Indeed, more power = more fun;). Though, I'm trying to keep this vehicle inside of brackets for pedal assisted vehicles in Europe so max 250 W constant power;) Cheers!
Thank you! Indeed, the results of my experiments are not very scientific. I'm working on a new build and I'm planning for some experiments with sensors to find how much tilt is needed, etc. Cheers!
For velomobiles quite some experiments were done, years ago, around 1990. Camber can be made very large without increasing the rolling resistance of the trike (velomobile). With adjusted geometry you can go up to about 20% before noticing increased resistance.
@@pedro-neves You may get unusual tire wear from high camber, as the tire flattens where the weight of the vehicle meets the road. Since this location is off-center, the flattening will be off-center as well, and some tires may not have as much tread/traction at the edges and could wear more quickly. Awesome consequence on a trike, where you can 'rotate' the tires and wear the tread on the other side when the first is used up. High camber matched with tires that have good tread coverage may allow you to get twice as much life out of them.
@@benjaminteasel3942, thank you so much, that i s a great tip! I was considering that, because the tire is round I have no issue with camber but you are absolutely right - most of the tire thread is in the center. Cheers!
Track-oriented cars usually run about -2 to -3 degrees of camber to improve stability. Also 1 or 2 degrees of to in. Drift cars run serious negative camber on the front wheels to improve front grip during slides as you load up the outside wheel
Thanks! Ya, I can see how that makes sense. Regarding the Toe, What I have been learning is that Toe should just be zero but, often in cars, there is a little bit of Toe designed into it to compensate for acceleration or braking torsion. Cheers!
Thank you very much! And I already added a motor;) Check it out here if you're interested: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=hKyIqX8F9g3twxFA. Cheers!
Hehe, thank you for the beautiful part;) Indeed this is more complicated and expensive than a bike. And I love bikes. This is an alternative. I think it can be made to be safer than a bike and more proper to carry cargo than a bike. I also think that, by making it open source (will start in the next project series), it can be made to be cheaper than commercial cargo bikes. Also, this may help pave the way for knowing how to make a small car (L7 category). Cheers!
I loved this video sooo much 😅 I could add some of my advice on geometry of the front end but it looks like others comments have covered this, loved your real world testing, am building my own one of these 3 wheeled tilt bikes but with a motorbike engine, swing arm, back wheel and shock at the back, but where mine with differ is that I am building a aluminium tub for sit down position like in an open wheel racecar like F1.😅 Really glad to see this and would like to see your improvements. After you put a motor on it you could actually also have a low seating position right on top of your cargo area lol, cause the lower to the ground you are increases the sensation of speed and lowers the centre of gravity, and you could make it reversible so you could change between riding/driving positions when ever you like 😅😅 really good work
Thank you so much for your kind comment! Indeed I've been getting so much help to improve my design and build! I think that the next one will be much better;) Regarding the motor and riding position - I'm constrained because I want to have pedals. I'm designing for a class of vehicle that can ride in Europe without license plate (or insurance) - can have motor but only for assisting the pedals, cannot work on it's own. Regarding your design - sounds awesome! I would just love to see it! If you publish your design somewhere, please drop a link;) Cheers!
Amazing project, you getting in the wright direction, and yes this will be a dream with a electric assisted power, though you ever thought about a chainless but a dohc drive to make it a ideal bike
Thank you very much! I already installed assisted power. You're welcome to see in this video: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=-XVDMtRxLR1wAkMe. And I already have ideas for the future. Cheers!
This is so fascinating! Thanks for all the testing! Now if I could only learn to weld properly (all my experiments trying to weld up my own cargo bike have been disasters so far! )😊
Thank you for your very kind comment! And some words of encouraging: I'm also not a good welder. I believe you get there by practicing. I'm also looking forward to doing better, and I'll transition to TIG welding soon. Makes me happy to read that you are working on a cargo bike build;) If you ever need something, you are welcome to reach out;)
The only thing my ocd head noticed was the main shaft hidden was connected to the right only, rather than a dual connection to give a more sturdy control. ( Like the difference between the way a two wheel trailer that connects to the left side only, which gives the rider a herky jerky feel when riding or the Burley Coho XC one wheel trailer that connects on both sides of the hub and the difference is amazing! ). ✌️🌍✌️
Hello and thanks for the tip! On my newest build, I'm trying cable steering: ua-cam.com/video/UWFQ6nFzpgE/v-deo.htmlsi=2XVGCgMp_hvAzU-B. But if I ever go back to a shaft connection, I'll have in mind the possibility of connecting both sides. Cheers!
That's awesome! I'd like to build one myself too! Though my engineering skills aren't at your level. What electric motors are you thinking of adding to the bike? Hub? Mid Drive?
Thank you! Building is awesome;) and you can always learn, no rush;) I am currently converting the trike to electric. I will publish the video in a few days;) Cheers!
I love the video. -- The detailed approach to all the variables and riding conditions is very impressive. On toe-in, it seems like if 5deg was too much and 1deg was hard to notice, then trying 2 and working up to some limit >=5deg would be worth testing. Finally, viewing in the U.S. 2024-05-11, I got a pretty offensive ad demonizing immigrants.
Thank you very much! With so many contributions to Toe in comments in this video, I end up concluding that one should aim to have 0 deg Toe. The reason why steering geometries are calculated to have Toe is actually to compensate for deformations or other geometries. So, the objective is always to have 0 deg Toe. Cheers!
Outstanding efforts! I tried commenting earlier but didn't see it show up, so I sent an email to the account linked in the channel info asking if you might consider using something like Cannondale Lefty hubs for your next front wheelset and knuckle design. It could save you the fabrication time and plot a course to a design which could eventually be implemented by more people.
Hello! And thank you very much! The hub is a very good point. I am designing a new hub that is of the same style as the Lefty. A Few minor differences such as 28 spokes and a left thread for the left spindle bolt so that the wheel doesn't untorque the bolt when riding. I'll answer to your email and share a few pictures. Cheers!
Ackerman is also called "toe out on turns". It's so, as you say, the wheels turn at a different rate on turns, as of course, the inner wheel has less of a circumference than the outer while turning.
Thank you again for the tips! Indeed, I think I understood the relationships between the geometries. In my next build, I believe I'll get the Ackerman right. Cheers!
What would really tighten that turning radius up would be to have rear wheel steering! I kid 😉Thanks for the fantastic presentation of your process and build!
Thank you very much for the kind comment! Regarding the rear steering, actually, I tried a cargo trike with rear steering and thought it was awesome! Check it out here if you're interested: ua-cam.com/video/uW5teIGglsE/v-deo.htmlsi=3ylcLOflEAKqAjmJ. Cheers!
Very nice build. I was thinking about something similar. It will be even better when you get the electric motor in. Plus with the trike set up you can have a larger battery pack :) Have you thought of having the power come from the rear wheel? You could have a larger motor and less cost. best of luck to you.
If the front wheels are to be unpowered probably -0.5 degree to -1 degree would fine to adapt to small flex and movement. If powered similar amount of not a bit more positive would be good to make up for flex of components. Great bike also great process, testing is always best.
Thank you very much! It's so kind of you to answer the questions that I had to help with my build! It's so nice to share what I learned and also make questions about what I didn't understand and getting great explanations. Cheers!
Camber will make the load uneven, most likely part to straight out break is the spokes as the load isn't shared as well between the sides. If there are stability issues, it's usually better to fix them than trying to compensate for them.
Just to contribute... the toe angle is something that has sense just when the weight of the wheel/suspension system is relevant and/or the power of the engine is relevant compared to the hardness of the materials. In a tricycle or four wheel bicycle you can hold it neutral. But thank you for all your contents
@@Ale_775, and thank you so much for the contribution. It's been a learning process, and it's great when we can make a forum out of it and share each other's knowledge! Nice notes on Toe, thank you.
Thanks to you Pedro, You really did an excelent and useful job! I was speaking with an Audi mechanic the other day and he told me that for a car of roughly 200CV the driving rear wheels have an open toe angle in a way that if you measure the distance between them in the front it can be up to 10/12mm more than in the back if I understood...
45 kilos is very good for a DIY steel cargo trike. I expected something like 60 kilos. Well done! You changed the geometry a lot. 6 degrees of camber is a gigantic change to 0 Degrees. Many rayle cars don't have that much, even though they sometimes apply a lot of it. Your build is very good, so enjoy it for a while. But maybe in the future you could redo the test with smaller increments.
Thank you so much! Indeed, 6 degrees is too much. I think it will end up with 1-2 degrees. And you are right about the big increments. These experiments allowed to really demonstrate the effect of the changes in the different geometries (exaggerating is like a magnifying glass) and to find the ballpark of where things should be. Cheers!
Toe is generally used to optimize lateral forces produced by the front tires at a specific range of steering and slip angles. I’d assume given the necessity of efficient use of energy; you’d try to match a marginal amount of toe out to reduce tire scrub from camber thrust while going in a straight line. Optimizing your Ackerman is probably a more ideal solution to lateral forces while turning vs toe given the constraints.
@@pedro-neves because leaning changes the steering geometry so much have you contemplated the implications of completely decoupling the front end from the rest of the vehicle. Putting a pivot point so the rear can lean independently?(would require an anti roll bar to maintain a neutral starting point on the front)
@@pedro-neves Understood. Simplicity is rather important in many cases!! Have you looked into how Yamaha does their linkages on the Niken? For some reason It slipped my mind when I was commenting on this that it even existed.
@@joshmerklin, I looked both at the Yamaha and the Piaggio MP3. I think I've been looking at anything with two wheels in the front for the last few years and my creations end up being a result of that mixed with my own thoughts and of course the contributions and thoughts that are shared with me, such as yours;)
I think the toe angle will have an impact on high speed cornering and stabilty when slip angles start to come into play, but you're not going to gain anything at the speeds you're doing. It also causes scrubbing of the tyres, which you noticed as resistance at extreme angles, but is still there creating drag at low angles. Likewise camber will create some scrubbing and increase drag as you are effectively riding on cones which want to roll in circles. If you get noticeable gain in stability though it's probably worth it. For the steering, rather than a T bar shape central pivot to move the steering rod joints outwards, you could use 2 central pivots linked by another bar to make a parallelogram mechanism?
Hello and thank you so much! Agree with Toe - will be 0 deg because there is not sufficient vehicle dynamics to make sense to calculate Toe. After multiple feedback, I start to think that camber will be 0 to decrease forces that are not perpendicular to the structure. The parallelogram - Yes! Recently, someone that watched the video sent me some drawings explaining how the parallelogram would fix the issues that the T introduced. Thank you so much! Cheers!
@@pedro-neves I think a small amount of camber (0° to 2°) shouldn't generate significant disadvantageous forces, but if you get a significant improvement in stability and feel then it's worth it.
Toe in and out is all about tyre wear. "toe' on cars simply compensates for driving or non driving wheels, so that it drives parallel to the road while driving (zero toe in). Front Wheel drives want to bring the wheels together (so needs toe out to start with). Read Wheel drive, the front wheel gets pushed out and so needs toe in to start with.
traditional bikes have a metric called 'rake' that describes the offset of the front wheel from the steering axis, it stabilizes the bike. Tire contact patch behind steering axis and wheel axel in front of steering axis (rake) for stable handling.
@@pedro-neves Thanks for the response, you're doing excellent work. I do think that a little bit of 'rake' will stabilize the trike for hands free riding. Axle in front of steering axis means the steering tends to self straighten (assuming there is some 'camber').
Thank you very much! I made the hubs;) I have a video just about that: ua-cam.com/video/sU2ZS7Nlbj0/v-deo.htmlsi=gPJPbeqmm7bXMFMa. The next iteration of this project will have new wheels and wheel hubs that I'm working on. Cheers!
Sorry, I have to say I already know that toe-in is not a function of preset geometry, but a counter to flexing geometry. Ideally toe-in would automatically counter whatever geometric flex was caused by whatever weight caused it. So toe-in is only a work around to flex. The best way to anticipate a certain toe-in is to put on the entire weight of rider & cargo, introducing the geometric flex, & zero up the toe-in-out while under load. After removing the load, whatever toe-in results is correct only for what that load was.
Thank you so much! Indeed, I have learned this in the meantime. I now understand with the kind help of people such as you that the aim is to have the Toe to 0 and that designing Toe into a vehicle is thought of to compensate for flex. Cheers!
To get the Akermann steering correct, you need to have the tie rods level with their pivots, as you had to move the steering mechanism back to accomodate the castor plates, it's always going to be a compromise. The other issue you're finding is that the steering mechanism is a T bar, so it turns the T which alters the spacing of the tie rods, again, this will be better with the T being central to the steering tie arms. It would also be best if it slides rather than turns, but this is quite difficult to do while having the steering link to it.
Hello, thank you for sharing that analysis! Ya, the T does change the steering geometry, but I had to put it because I have bump steer (when tilting) without it. The T can be smaller once I get rid of the castor plates. And also, when I remove the castor plates, I'll be able to have the steer pivot parallel with the tie rods. It's easy to make the drawings for Ackerman but once all these adjustments start to pile up, then it becomes different.
@@pedro-neves yes totally get that, what you can do to help when tie rods are in line is create a parrallelagram using 2 pitman arms, the just use the existing steering arm to drive one of the pitman arms. That should sort the over-angle and bump steer issues in one go. 😁
@@overlandready, pitman arm! I didn't know what it was until you told me about it and I went searching. It's super cool to make something, share and have people helping me to make a better one! Thank you for that!
2points camber to 1 point caster active motion 2-1 ratio or 3 to 1 for lower speed steering stability vs control vs °s of motion. Use ball joints on your tie rods. The use of an A arm usually a lower one would ensure accurate camber caster motion decreased drag ect
The Ackerman principle is at any point of turning, the axis of all three wheel will meet at one point… set it in a way at full turn , the axis of both front wheels will both meet, along the axis of the rear wheel… check with the kenimatics of motion…
Thank you! Indeed, with this geometry, the Ackerman principle is achieved in most of the range of the turn but not in all. I believe the next build will have all the Ackerman principle corrected. Cheers!
Whatever your used to will feel best. After returning to cycling after riding a heavy motorcycle, I literally couldn't keep the bars straight. It takes time for your brain to adjust to the new feeling and sensitivity.
I totally agree! When changing many things, it's hard to know what "feels" better. I try to have some standard tests to make things a little less subjective.
Hey, just found your channel and I love what you do. I can't offer any advice on your mechanical design, but for your experiment design I recommend looking into orthogonal (Taguchi) arrays - it's a way to test multiple variables and how tbey interact much more efficiently. As others have suggested caster and camber tend to work together, and this would be the way to find the right setting in a greatly reduced number of experiments. Hope this is useful!
Thank you very much! That helps a lot! And you are right - testing every setting against every setting would be very time-consuming. I also came across this video that explains very well your suggestion: ua-cam.com/video/5oULEuOoRd0/v-deo.htmlsi=rYvmZocl1xeetJy5. Cheers!
Hello, good question, actually it's already narrower than common cargo bikes. This trike is 70 cm wide and it's common for cargo bikes to have 1 or 2 more cm more. Cheers!
@@JohannesSchmitz yes, I agree. The compromise that I was thinking about is - being narrow enough to go through most places and traffic, while having the added stability of a trike. I was somewhat inspired, e.g. by the Piaggio MP3.
you might want to try camber and caster together at higher angles. say 20-30° of caster with 2-4-6-8° of camber. you dont need to remake the arms for that: just lower the suspension, so the arms droop lower. just doing that will increase camber with your current geometry. 30° is close to the typical steering caster angle (also called rake) of a bike, which is between 24° (super agressive, seen on time trial bikes) and 34° (super slack, seen on downhill frames as it helps absorb landing hits and maintains stability with the bike at full droop, when the fork is fully compressed) the caster angle needed is relative to the wheelbase. the longer the vehicle, the more caster is needed to help reduce the turn radius. as far as my research go, toe helps adjusting the ackermann, combined with caster and camber. you can see it dynamically change as you steer on the final form of the bike. that's the direct effect of having close to 40mm of scrub, something i will explain later. you might want to make a new camber plate with 5 degree increments, something you can easily do by drilling a new set of holes closer to centerline. and when making the new steering hub, since you're making your own, could fit *around* the knuckle. the closer the knuckle mounting axis is to the center of the wheel, the easier it will be to adjust, and you will have less scrub (the wheel will travel less relative to the pivot center) and dynamic toe out when tilted to the max (as the wheel is closer to the knuckle). in automotive terms, this is called positive offset. your car has positive offset, it is called ET in wheel terms. should be between +35 and +55, usually. that can be done with a virtual center wishbone (but that is extremely complex since you have tilt steer on top of double wishbones) : instead of 4, 3 point wishbones, you have 8 links, who work in pairs. the space between the end of the links at the knuckle, relative to the space at the frame, deports the steering center to and from the wheel centerline. and you can weld together these pairs at the wanted knuckle offset to spread evenly the suspension load. this means you can forgo the camber plate, as you can effectively change caster as you change the virtual pivot's location... yeah it's going to be a little bit complex to read, i know. you can see one being made on this channel: www.youtube.com/@councilhousecreations8035 the lad at council house creations had to do that because he's making a 4 wheel drive gokart... no room for a conventional knuckle close to the wheel center. you can see this principle of a virtual steering pivot on a few 2 wheeled cargo bikes, like some of veloma's, the catan titanium frame from a few years ago or the EScargo, where the caster and the angle relative between the frame and the knuckle create the wheel's trail and caster. to not mix with bikes like the ketter cargoline, which run a pivot inside the wheel with a fixed swingarm, something seen on some motorcycles too, like the bimota tesi, vyrus 985 or yamaha gts1000.
Thank you so much for the very complete set of tips! There are so many things about the geometry and I keep learning from the community, such as yourself, that clearly has knowledge on automotive geometries! I try to compile all the advice that I get and put it into the next iteration as much as it fits the amount of changes that I'm making;) I plan to make this easier for the community, actually. I will finish this series and then start with an open source project where I share the files in a very organized way, with versions, in editable format. It takes some time because I don't do this full-time, but I hope you will comment on the next iterations or even edit the drawings when I start sharing;) I will also look into those creations in the UA-cam channel that you shared. Cheers!
As the lead engineer of the original Arcimoto cyber trike project, good show friend.
Just checked out the Arcimoto. Looks pretty incredible, congratulations! And thank you so much for the compliment! Means a lot, coming from you! Cheers!
@thewerst8346 whatever happened to the MLM? Arcimoto made all kinds of noise about it then... crickets!
Seems Arcimoto is now defunct? Sorry to hear that if that’s the case, was excited for the new trike bike!
I always wondered what happened to those, I figured we'd be seeing fleets of them as delivery vehicles by now.
Castor and Camber work in tandem. As you have observed, a lot of caster will make your bike stable at speed but when riding slow, it tends to 'fall' into the curve. This is because as you turn the wheels, the frame of the bike moves lower. Therefore the weight of the bike acts as a force that wants to increase steer angle. Camber has the opposite effect, when you steer away from straight, camber will lift your bike (with 0° caster) . Therefore the weight will always push it back to its lowest position, which is going straight. By choosing caster, you can control high speed stability, by matching camber you can restore / adjust low speed stability.
Toe at 0° is usally for best efficiency, which i guess is most important in bikes. If your ball joints do have a little play toe out / toe in will put preload on them and they wont flop around all the time. This preload techinque is also used because ball joints have a reduced livetime if the direction of force does change often. This may be irrelevant on a bike that does a lot less miles and is way lighter.
As a rule of thumb, 20° caster is already unuasally high and compensation by camber will not work perfectly anymore. typ. is 5-15° in the applications i know
Another factor you havent touched on is the length of the control arms. Usually, the lower arm is longer than the upper arm. This gives the effect off added camber when the suspension is compressed. One reason for this is to eliminate tire scrub when going over bumps, the other reason i believe is added stability when carrying heavy cargo. This may also be a reason why lengthening your lower control arm for added camber gave you such benefits. However it can also be done by moving the frame mounting of the upper control arm further outside.
And when changing suspension geometry, always check that the sterring rods and their joints are still correctly spaced in the plane of the other joints, otherwise you will introduce bump steer. Bump steer is when compressing the suspension changes toe.
Very cool project of yours and i completely understand that a test must be reduced to some variables, thank you for the work you put into this experiment!
Uauu, thank you for the explanations on the impact of geometries and the relations with each other. I hope others interested in the geometry go ahead and read the comments. There is just so much juice in them! Truly appreciate it.
I'll just confirm that the lower wishbone is longer tan the upper, designed to have zero scrub radius. And that I compensated the spacing of the steering arms with that T in the front steering pivot. I did have bump steer before this part but not anymore.
Thank you so much!
Exactly, I was going to post the same thing. It is also true that if you have power steering, you don't have to even know its is harder to turn. I build r/c cars, it all done by electronics, not human.
Brilliant comment. Thanks for the benefit of your expertise and clear language. There’s so many variables at play and so much fabrication involved in arriving at a working prototype. I wonder if a simplified 3d model could be 3d printed desktop size to study the tilting and turning geometry. Then visualizing the things you describe would be easier. What an amazing engineering design tool that would be and it would be fun to have a toy sized version on one’s desk. Tilting tadpole cargo bikes and recumbent HPV nerds would line up to see their design notions take shape before all the expense of cutting metal.
@@ciberbri59 totally agree on trying out things with reduced 3D printed models. Actually, this is precisely how I started this project: ua-cam.com/video/UylIv7d50uQ/v-deo.htmlsi=IRATRP0ND4vPwmU2.
Cheers!
This is the most important video on tadpole tilting cargo trikes on youtube. Thank you very much
Thank you so much for your kind comment! I do try to make it useful for others.
I agree. This was very useful.
I've been working on something similar and my biggest problem has been steering and the other is I want to make mine all wheel drive and put hub motors in the front wheels, but then because of the Ackerman principle the motors would have to drive at different speeds when turning...and its a little bit too much software for me. So if you ever get there please make another video 😁
@@rogerdueck9725, thank you! Ya, now we start to see some cars with electronic differential. Even with two motors in the rear wheels such as the new Tesla Model S and X Plaid and Rivian trucks. But I agree that it's quite complex. Cheers!
@@pedro-nevesThankyou for this video and your video of your build. These titling cargo bikes have always impressed me and seeing your videos about how it works was great!!! Have you seen the ili cargo bikes, they have some interesting tilting bikes, it might give you some inputs for future developments, thanks again it's inspiring to see people like you create cool products in your own back yard
@@pedro-neveswhere are you located? Are yiu in Europe,
Tadpole cargo trikes make the most sense:
- two tyre contacts in the front
- redundant front brakes
- can use a tilt-lock
- retains the simplicity of a single rear wheel
Love it!
P.S. : there are similar trikes called "HNF Nicolai CD1" and "Mäx & Mäleon"
You could look up what values they used as a reference.
Hello, thank you for that! I agree with the advantages that you mention. I have actually tried a Nicolai once and thought it was incredibly cool and I watched a few videos with the "Mäx & Mäleon" which also looks cool. Cheers!
Also the Butchers and Bicycles
Whatis your opinion of the Dutch Black Iron Horse configuration?
@@tonicedeno, Hello, one small correction - I believe the Black Iron Horse is from Denmark.
And, I tried one with rear steering and I liked it very much! To be hones, I think it's the best I ever tried for slow maneuvering.
The reason why I chose the front tilting to develop is because I like more how it rides. With front tilting, it rides fast better (more like a bike). Cheers!
I knew a genius fabricator who created a 4 wheel mountain bike with a roll cage body and I followed him at 50 mph on the first run at Plattekill where we were downhill racers. anyway. his toe-in was about 1 degree and camber was about 7 degrees. His vehicle had a solid rear axle so he could use the inside rear wheel to friction brake in sweeping turns. It was awesome to behold
Sounds like a fun downhill! Thank you for those reference numbers!
Video link
I need some footage of this thing. Ain't NO way!
'A 4 wheel mountain bike...', wouldn't that make it a pedal cart?
Tell about the uphill part
Bravo! I am not building a cargo bike but loved every minute of your analysis and commentary. Please continue, looking forward to the next revision.
Thank you so much for your inspiring comment!
Same!
I'm not sure if anyone else did but I found this useful to understand what toe, camber and castor means and now I plan on using this information to make better tunes in Forza horizon 5. Had the general idea on camber but visualizing it helps a whole lot more. Thanks.
That's so cool that this is helping you understand the geometry in a computer game! Thanks for sharing that!
@@pedro-neves Hey, now that you know the optimal angle for the wheel alignment, would you consider removing the adjustable part in the center to shed weight and make the assemble more simplified?
@@S-I-R-E absolutely. I'm already working on the new design. Removing the adjustable parts will allow shedding weight and also package the whole suspension and steering a little bit better.
Cheers!
@@pedro-neves sweet!
You are a skilled scientist and inventor. This video is much appreciated for your detail are care for these very relevant topics.
Thank you so much! Makes me happy that you find it useful!
This has to be one of the best cargo bike builds on YT. Well done Pedro. I have thought about building a3 wheeler so many times, but I have been riding a 2 wheel 8freight for years and for me the benefits of 2 wheels on the infrastructure in the uk outweigh the benefits of 3 wheels. But I would still love to build one like yours.
That is very kind, thank you;) I also love bikes and cargo bikes and see advantages in them. But one thing is fore sure - trikes are more fun to build;) In case you're interested I did a comparison once: ua-cam.com/video/uW5teIGglsE/v-deo.htmlsi=ozGWutrevJbW14d5.
Cheers!
Hi Pedro, well done. Nice piece of work.
As regards Toe, I would suggest 0deg. In cars they sometimes set a toe that allows for the flexure of the rubber bushes so that the end result ubder load is 0deg. 0deg is minimum scrub so maximum tyre life and minimum drag.
As regards castor, you are altering trail (the distance between the steering axis intersection with the road to the tyre intersection) as well. Increasing trail will make the steering a bit heavier, decreasing trail will make it twitchier. It also means that in transferring your results to a larger wheel (if you did that) may alter the optimum.
For the ball joints binding I suggest putting a bend in the arms so that the ball joint is at 90deg to the steering axis to even out the play in the 2 directions so lean-ability is maximum.
Finally, neg camber will wear the tyres on one side. So from time to time swap the tyres left to right and vice-versa to get best life out of them.
Doing away with your castor plates will let you shorten it a bit without affeting your load bed.
Finally, if you had a lean lock, that would be handy when you have to stop for junctions, traffic lights (both feet on the pedals) and parking. It may also help balance on really steep hills. You could delete the side stand too.
Lovely job, I look forward to the next part.
Thank you very much for the kind comment and comprehensive set of guidance!
- Understood regarding Toe and Castor!
- For the ball joints, I plan to do just what you mentioned - design the angle into the knuckle instead of letting the ball joint handle it.
Totally agree with getting rid of the side stand;)
Cheers! Have a good time!
I had a couple of these in mind as well, great comment
Hello! Engineer here :) Nice to see that this idea keep moving these days. I have done a lot of leaning trikes with motor. Let me share some insights?
First one - consider a Roll center. Surprisingly, but CG for Leaning trikes must be at groung level instead of over it like a car design. Thats why you struggling with balance while ride without hands. The second - Ackerman angle: Try to decrease amount of it because : A. slip angle of tyre, B. tyre works on a sidewall while leaning and you get camberthrust.
And last one. Due to long base your front (air) spring too stiff so it would be harsh with strait (especially at high speed)..
(and.. front wheel pressure. IDK but there might be 30-50% lower than ordinary bike)
Hello, thank you so much for sharing your insights! They help me to improve!
- I definitely intend to lower center of gravity.
- Ackerman took a lot of work. I started with the "designed" geometry and then did adjustments until I feel that there's no rub. There are a few things to fix for sure. I'll consider camberthrust, thank you for that!
- Ya, I agree that spring air pressure and tire air pressure contribute to stability. As it is, when I load it with 45 kg, the shock contracts about 1/3 of its range.
Cheers!
@@pedro-neves Good luck!
@@audaxrallymedia , thank you very much!
how can CG be at ground level? do you mean below wheel center?
@@federicoromero6130 Oh! Thank you! Youre right. I mean RC. Roll Center. Of course CG located way up from the ground. But Roll Center must be located at the floor, and imitate front wheel of regular 2 wheeled bike. In other cases 3 wheeled leaning trike hard to drive. Rider feels instability. It looks like front wheel start to slide from side to side.
I'm building a tilting trike but with enclosed cabin for weather protection and better aero, this vide is super useful, thanks
You're welcome;) thank you too for your kind comment! And good luck with your build!
I would love to see that. I've had that idea for years but not the skills to do it.
Toe is not typically used on leaning vehicles.
Because they lean, the just don't need it: tilted wheels solve that issue already.
0 toe is fine.
Thank you for sharing your thoughts about Toe! 0 seem the best to me too;)
Toe is related to camber. Positive camber requires toe in, negative camber toe out in order to make the tire track straight.
@@anvilsvs thank you for that!
Toe is important when you have 2 wheels. If you want to travel in a straight line. Uneven roads will cause the bike to pull as will suspension travel and as someone said camber is involved too. How does the bike handle bumps or gutters when one wheel is not on flat road?
@@danc2014 , for me, one of the big advantages of this mechanism is uneven roads. I feel pretty safe. In my opinion, it's safer than a bike.
Your creations are getting better and better. This trike is just brilliant. Greetings from Italy
Thank you so much! I do aim to improve every time, so it's very rewarding to read your comment;) Greetings from Amsterdam!
The corect turn geometry is the one that when turning, the projections of the two wheel angles alyways cross in the extension of the back axel.
Toe mostly used on cars to enhance break and acceleration performance, and fix changes of geometry on wide wheels.
Usually, for the geometry and handling toe-out is what you want. It may help tweak the lost of handling from caster.
Maybe 6/5 degrees is too much for toe.
Thank you very much for helping to understand Toe a little bit better. I start to comprehend it! I hope it's also useful to others reading your very nice comment.
I'm not engineer but having a good feel with technical stuff my opinion is that if camber no toe,it is one or the other,both is too chaotic for a smooth ride and you actually already proove that camber is usefull to add. Congrat for your patience!!and thanks,this was great and really usefull for the community.Ps you gave me some more reasons to make mine!!Thanks again Pedro.
I'm so glad that this inspires you to start your build! Thanks for sharing and for your kind comment!
Nice project thanks for sharing. Any Camber will "work the spokes" as the wheel rotates, i.e. the load in the spokes will go positive and negative with each rotation of the wheel. Athletic Wheel chairs with camber have problems with spokes loosening.
Hello, thank you for that! Indeed, I was not thinking of negative effects of camber, but now I see that there will be extra strain on the spokes and bearings.
I think I will still live a bit (1-2 deg) but definitely not 6 deg.
Cheers!
very helpful technical tests. thank you for sharing your knowledge.
You are welcome! Thank you for your kind comment! I try to share knowledge in the most comprehensive and useful way and will try to keep improving.
A mechanic once explained to me that toe-in gives very little real benefit to steering or stability, but that exactly 0 toe is very hard to maintain and even slight toe-out has a very negative effect on steering. Therefore slight toe-in gives a slight safety advantage.
Really enjoyed this video and your process!
Thank you so much for your kind words and for the notes about Toe!
When we visited Amsterdam, I amazed by the cargo bikes that I saw there and been meaning to fabricate one similar to what I saw there. Yours is a bit more complex for me ahaha but by seeing this build, it gives me motivation to go ahead with my project...
Hello, thanks for sharing! For me, it's really cool to know that I motivated someone to start a build;)
Cheers!
Hi Pedro,
You are an inspiration to all! Hats off to you for your build!
I would love to see if 5 degree caster is any better with negative camber you have set. I know your bolt locations do not allow this, but since you are going to alter the build, maybe you can try this on the old build before committing to the new design. I would bet that you would enjoy the additional manoeuvrability without sacrificing much stability.
As you described you can add electric motors. I don't know if your ultimate purpose is more geared towards heavier cargo or not, but it seems like you would be ok with a pedal assist system given your location is mostly flat. You could try front wheel drive, (would be a quite a bit more complex as you need to control the speed based on many parameters, steering angle, tilt etc.) or even all wheel drive (but it seems like you wouldn't need this). If you are making the new one from scratch, you can also try to use a more optimized design for the rider frame. Most of the frame geometry is overengineered for the loads you have it seems, you can potentially cut back on weight there a little bit.
If you design the entire linkage including ball joint with camber and caster settings you have in mind you will enjoy a better ride and longevity.
I would advise against toe due to fact that your vehicle is tilting and thus no need for "correcting" steering dynamics due to weight and contact patch distribution is needed. With toe you will get added wear on tyres (negligible if you don't use very soft tyres) and most importantly additional effort is required to energy dissipated as heat with geometry causing shearing on contact patch. In terms of handling feel theory suggests that toe out will make it more "twitchy", in non-tilting vehicles a little toe-in goes a long way for responsiveness but has some costs for high-speed stability. In your case the effect at such small angles is negligible as you have tilting. If you drive front wheels with motors, then you might want to consider toe-in for added traction, but again using ESC to control torque would be the better option.
I appreciate the knowledge you have shared and hope to make use of this for myself in the future.
Thank you so much for your kind comment and contributions to knowledge sharing!
Indeed, I am left with the question of exactly how much caster;) I only know that 10 is better than 0 and better than 20.
I already have an electric kit with motor in the rear wheel to install. This has the advantage of being a very simple installation, and I can continue the development and tests and ride more distance without becoming so tired. At the same time, I am starting the project of developing an electric mid-drive with gearbox. I'm also excited about this project;)
I will redesign for fixed linkages and for the correct angles between knuckles and ball joints.
I have learned a lot about Toe since I published this video;) it’s incredibly cool how much knowledge people are happy to give. Thank you.
I also appreciate the knowledge that you shared and makes me happy that you find use in the knowledge that I shared.
Cheers!
Love this research and content - thanks for taking the time and extra effort in making an adjustable config so you can test different options.
I've wondered about a cofiguration where as you are initially turning, the bike is more resistant to the action, as a way to improve stability riding in a straight line.. then as you lean into the turn, you're essentially confirming to the bike that are are actually trying to turn, and the turn gets easier as you commit. Added bonus to this is that it also would prefer to return back to straight riding at the end of the turn
Thank you so much for your kind comment! I love to create and share knowledge.
Let me tell you that I once did an experiment - locked the tilting to see if I liked how it rides. I didn't, either in straight line or in turns. It becomes a totally different vehicle (more like a quad) and I don't like quads... The free tilting mechanism gives the vehicle a sense of riding like a bike, which I like, with the added safety of two wheels in the front.
I know that this is not the same as you proposed but gives a little bit of insight.
Cheers!
The level of talent and knowledge you have...i m humbled
That's very kind, thank you!
Just stumbled across this video, what a great project. I live in CPH and have tried many different 3 wheel cargo bikes, currently with the Butchers and Bicycles trike for family duties. I have to say the tilting trike is a the best solution that I have tried, on the Butchers the main drawbacks are related to the room the wishbones are taking up from the passenger/Cargo box, and the fact that the ‘cargo’ weight is also positioned directly over the wheel axle, if I put an adult in the box hard braking and that weight shift makes the bike pretty unstable, your solution is definitely getting around that. Also, from experience it can be pretty disconcerting to run out of ‘lean’ when committed to a corner.
Hello, thank you very much!
I also like the tilting solution. For me, it's the type of trike that gives the best riding experience.
Interesting that you're saying that you experienced running out of l lean when riding. I thought this was a problem just with my design. I know how I will improve it, but not eliminate the issue totally because of the limits of the ball joints.
Thank you for those descriptions of riding your trike! Really helps to consider pros and cons of design.
Cheers!
XLnt testing! i have a few recumbent e-bikes and trikes and lately bought an e-Heisenberg secondhand. it stays, always pleasant to feel the different geometries when you ride one.
The e-Heisenberg looks very cool!
NO WORDS TO THANK YOU.The greatest video of explaining ....I like be a special friend of you from Sri Lanka.....
Thank you too for your kind words;) Makes me happy to read such comments that sharing this work is useful;)
Cheers!
Another piece of the geometry you can change to achieve Ackerman is the tie rod connection point on the steering knuckles. Move the tie rod connection points inboard. This will turn the inboard wheel more relative to the outboard wheel. You mentioned moving the steering arm forward. I interpreted your statement as moving the whole assembly forward. You could just rotate the arm around so the connection point is forward of the pivot point. But this would require crossing the arm from the handle bars. I’m familiar with setting this up in four wheel vehicles. Requires some shifting in thinking to do it on a bike. For what my opinion is worth, I also don’t like the idea of camber on bicycle wheels. They don’t deal with side loads very well. I’d try to keep the wheel aligned with the resultant load. But you probably know that already.
Thank you so much for that!
Indeed, it's been a big debate about what moves where in the steering. I'm now designing a new vehicle and haven't decided because some decisions get in the way of others, of course. But I understand what you are saying.
Regarding camber, also after some comments such as yours, I'm now almost sure that it will not have any camber.
I appreciate very much the constructive suggestions.
Cheers!
Wow, what an extraordinary project. I ride an ICE recumbent e-trike. Me and the trike are a little lighter than your setup, and there are a lot more spokes on the front wheels. But even then I'll break one every so often. So I would agree with you, more spokes! I run drum brakes up front, so no hydraulic maintenance, and I really like the progressive feel. Perfect for tadpoles. Anyway, good luck with what you are doing, you are obviously a brilliant young man.
Thank you so much for your kind comment!
I'm working on stronger wheels with 28 spokes (and different hubs).
I'm also working on making it lighter (next frame will be made of aluminum).
I love that there is a community of tadpole lovers!
Cheers!
This was a fun exploration of the math behind steering geometry. You might further refine results with rake & trail adjustment to bias tandem tires load vs single steer on the front axle, maybe even with torque bias observations for left vs right steering effort with your current weight distributions. Thanks for sharing.
Thank you very much! Indeed these tests gave some insight into the ballpark of geometries but there is so much to find out. The next design will already have plenty of improvements. In the future, I'm considering to build a computer model for simulation.
Cheers!
Hello Pedro. For Ackerman steering. Draw a triangle from the middle of the rear axle to the steering pivot point on each front wheel assembly. Your steering rack links to the front assemblies on this tapering triangle. Then you won't need that strange double bracket at the steering input.
I hope I have explained well enough. Please let me know. Also very well thought out testing procedures.
Hello, thank you very much!
I think I understand your guidance. But, the double bracket at the steering input is used to eliminate bump steer. If I didn't understand correctly, is there a chance you could send me a rough drawing to pncnveves@hotmail.com ?;). I understand if you don't want to go to the trouble of sending drawings. But experience has taught me that community comments are of incredible value, so I chose to explore;)
Cheers!
@@pedro-neves Happy to send you a drawing my friend. I'll get onto it later.
@@pedro-nevesHey buddy. I tried sending you the email, but it won't send. Doesn't like your email address...
@@stevedobbsphoto, I'm so sorry, there was a typo in the email.:( Here is the correct one: "pncneves@hotmail.com". Thank you very much for your effort!! I tested the spelling to make sure I'm not wasting your time.
@@pedro-neves Sent again. perseverance wins.
Riding ‘no hands’ is how I confirm proper geometry.
I am not happy with a bike until I can control it coasting by weight shifting alone.
I never built a tilting trike but it is in my project list, and your work is going to make it easier. Thanks a lot.
I love that you find my work useful! Thank you so much for writing;)
Cheers!
Congrats on hitting such a milestone! Designing things is always such an interative process that takes patience and dedication. Your hard work and perspective are inspiring!
Thank you so much! I'm really happy that it's great to ride now and still having so many improvements ahead;)
I'm super happy that this serves as inspiration! Thank you for saying that;)
Very excellent design video, I really enjoyed it and I learned a few good to know things before I start making an inverted trike motorcycle! It will be interesting to see how much I need to scale everything up.
Thank you so much! Good to know that it is useful and nice to watch;)
Cheers!
Well done, Pedro.
This is fantastic progress.
I look forward to your next instalment.
Thank you very much! It's motivating to do more with such kind comments;)
In the next video, I'll install an electric conversion kit, which will enable me to ride more distances with and without cargo.
After that, there will be big changes. I will organize this into a project where everything has drawings and versions, and it will be easy for anyone who wants to use the drawings.
Cheers!
Well done Pedro
@@startcherif Thank you very much!
Thanks mate you have inspired me .
Not that I haven’t got enough going on. 😊
Thank you so much! You have inspired me as well with your kind words;)
Very nice...much potential...looks pleasing to operate, ride....lookin forward to electrics or combustion....
Thank you! Indeed, I already made an electric conversion. You are welcome to check it out here: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=dzjplPb94CF0m3Rw.
Cheers!
Beautiful ! Suddenly I know more about the geometriproblems. Thank you and good luck with the electric conversion, 10 kilos of extra muscles will make this a vehicle for the future city traveller. Perhaps a tentlike cabin for kids as the next project. I had theese thoughts myself 40 years ago, right idea wrong timing in my case.
Thank you for the kind comment;) And I'm glad that this helped you understand the geometry. This was the main intention with this video!
Indeed, it needs to be electric. I've been working on a conversion and testing, and I'm almost ready to publish the video about that.
And I agree with the tent! I look forward to it being good enough to carry people.
Cheers!
I have never had a trike, no intention to have or build one ever. Enjoyed the video anyway!
Thank you very much! Indeed, making these videos have two sides:
- Inspiring / helping others with building.
- Entertaining.
Cheers!
The Ackermann steering problem you have is caused by the (reversed) T-shape articulated connection. To obtain a symmetric turning radius, you need to use an I-shape, where both wheels extension arms are connected above each other (at the I-bottom articulated connection).
Also as you noticed; the 20° caster inclination on the central turntable making the steering stiffer is practically better applicable for high speed. Once you have the electrical version going high speeds, try to invent a caster central turntable that automatically adjust the inclination on the angle from 10° to 30°, as speed goes higher. If you manage to develop such a functioning system, you can patent it straight away!
Hello, and thank you very much for sharing ideas and tips!
Indeed, the T-shape connection complicates the Ackerman. The reason why it's there is to mitigate bump steer.
Regarding caster, I never thought of having it moving depending on speed;) that sounds pretty cool actually;)
Cheers!
@@pedro-neves ...as to the front wheel rotating Caster holder, it is indeed a mechanical surrogate for the hydraulic steering wheel system of most sport cars that automatically stiffens with high speed. All you need is to install a small electric motor, attached to a speedometer that rotates the Caster between 10° and 30° for speed up to 60 Kmh.
In fact, I have never seen that system implemented in Bikes before, so check it out and make some researches to be sure if it is a novelty. Once you have a working prototype, patent it asap! If later this patent proves to be profitable, pls do not forget my reward! 🥳
Beyond that, I have a good, revolutionary transformer bicycle draft, but unfortunately no workshop like yours to realize it.
Greetings from Berlin.
@@Big_Bang_Bong thank you very much for your tips! My approach with this project is to make things open source (the beginning of the next build will have drawings shared in editable format) in an attempt of us all learning together.
If you're looking for a place to work - I don't know Berlin, but I would imagine that it's possible to find a community workshop. Here's an example of how it works in Amsterdam. Maybe it will give you some inspiration: openbarewerkplaats.nl/.
Cheers!
Great thought. 1 down side though. When you load the cargo it will be harder for you to turn the vehicle. Because of the weight of it.
Hello, thank you! Indeed, the cargo helps to create momentum forward, so the vehicle is slower to turn.
You do want a small amount of tow in. It's hard to reproduce on demand but if you have zero tow, you can get a little shimmy in your wheels if there is even a little play in any of the mechanism. A small amount of tow in will prevent that, I don't think you need any more than 1 degree, 1/2 degree may be enough. You don't want to go too far because it will cause excessive tire wear.
Thank you very much for the tips about toe!
wow, great experiment.
I like the scientific approach
Thank you very much!
Very cool, Pedro. Love it. I think tilting trikes are the way of the future, (until we can just fly everywhere). Your idea of adjustable linkages is inspiring. My mind goes to variable linkages, using linear actuators, or cable levers, so that all could be adjusted on the fly. Cargo, no cargo. Hi speed, low speed etc.
Thank you very much! Well, the next one will have cable steering;) maybe not exactly what you are thinking of but still an interesting feature, I think;)
Cheers!
Nice video and presentation.
Positive trail length will induce a negative camber angle in proportional to the steered angle for balancing stability. Having a constant camber angle is a different issue.
Thank you for your kind comment and the geometry tips!
¡¡Hola, Pedro!! Following your progress has been fantastic! Thank you for taking so much time/effort to distill and present it here for all interested to learn from and enjoy. Your video production improves and improves, and that takes much effort and talent!
You are certainly inspiring me and sparking/filling my noggin with new ideas. Love it!!
It seems that a close to neutral toe is optimal for your design. More toe-in, or toe-out, would cause increased tire friction/scrubbing and wear, and add to your pedaling efforts. No es bueno. Since our human body is relatively meager in terms of power output, we are pretty sensitive to additional load increases or decreases. I do like how you gave several of the configuration ~2 days of trial. Riding different bikes/configurations may preemptively feel "wrong", but our body/brain adapts quickly and then we, as you were, are able to make better comparisons.
Also, if you had simply made a trike, with no suspension, bleccchhhhh! Vehicles like that become "dynamically dead" and it becomes far removed from the fun experience of a bicycle. Your front suspension definitely IMPROVES upon that!!! Now you have a beautifully unique tri-wheeled bicycle.
As for tools, have you improved and/or gathered new ones? Got a small (they can definitely fit your needs) TIG machine? It would be nice to see some 4130 chromoly tubing in the front, lighter AND stronger for a future iteration. Then you could refit that on a future, lighter rear end. A rear end that will maybe have a 7-speed gear cluster that would always be there and NEVER need an electrical outlet.
Oh, and straight handlebars are okay for aesthetics, but suck-suck for ergonomics. Hold your hands out forward, loosely, in front of you, grabbing an imaginary handlebar, and your hands grip at a natural ~12-15deg bend. In the future, consider that. Your elbows and shoulders will thank you! LOL
And, THANKS as well for speaking to us in completely intelligible English! You communicate excellently! Because of that your video is completely accessible to me. Lucky me.
You made me smile when you spoke of how you felt after all you have done to achieve your ride/design to this point. What you have done, in terms of creativity, is NO DIFFERENT than a fine artist who applies oils to a canvas. To think otherwise is simple arrogance or ignorance. Maybe big dashes of both! I REALLY like your creativity because its product is functional. It interacts with your entirety as you interact with it. AND, of course, in its essence, it is a bicycle. A beautiful bicycle.
Lastly, tip 'o the hat, and two thumbs up, to your camera dude/chic!!! Your video was greatly improved by their assistance. Please, pass my "THANK YOU!" to them as well.
I am only more excited for that day in the future when you share with us again...
PS Straighten out the nose of your saddle. I'm picky that way. LOL
Uauu, I wish I could put more than just one heart in this incredibly kind comment;) Thank you so much!
I aim to improve the video production every time. I always have some notes of things to do a little bit better. I aim to share knowledge and inspire others to build. Hopefully, adding something of positive.
It is very inspiring to me to read from you that you are inspired;)
I definitely agree that the body adapts. One interesting thing that I noted is: after you change, it feels worse, then after some time, it does not feel worse. Then you change it back to what it was, and it feels so much better! That's how you're sure that it was worse;)
This is much more fun to ride than a fixed trike for sure!;)
For my next project that needs some welding, I will definitely get a TIG machine. Not just because the welding process is cleaner and quieter but also I cannot express how much I have been grinding to clean the welds!... Oh...
Regarding electric power and gearbox - Well, soon I will start a project of developing an electric mid-drive unit with gearbox. I think this is the future. I'm inspired by the work of Pinion. I will use a bike for developing the mid-drive and in the meantime I will install wheel motor in the cargo trike to help me with carrying cargo around;)
As for the handlebars, hehe, well, I have to say that I had different handlebars in this vehicle already. I think that the MTB lover in me ends up trying to make a cargo vehicle like an MTB... If I'm really honest, I have to admit that I aim to make this cargo trike so good that I will ride it on an MTB track and jump with it. Then I'll know it's good;)
I'm glad that my spoken English is well understandable. That's important for sharing knowledge so thank you for mentioning it! I'm from Portugal so, as soon as UA-cam releases to me the feature of allowing multiple audio languages, I will also dub the films in Portuguese.
Aah, your comment on creativity is so kind... Kindness improves the world.
The camera chic has just read your comment and has a warm heart as well;) It has been a big contribution from her, improving how to film and doing it in the cold and rain. We love doing it but a comment like yours just makes us love it more. So THANK YOU to you too!
I am one of those that has so many project in a queue!... So will definitely make more and share. Many things to improve in the trike (I'm working on wheel hubs in the present), electric mid-drive with gearbox and a whole series about EV charging where I have professional expertise (I will teach how to make a super simple charging station, etc...)
Hehe, that saddle is in bad shape actually;)
Cheers! Have a great time!
You have chosen far to great differences.
Even 1 degree is a great difference!
You could have a look what cars use.
Indeed, I agree. The reason why I compared big differences was to amplify the effect of the change so that I feel what it does. And also to find out the ballpark of where it should be.
Cheers!
Amazing work! Thanks to the second camera person
Thank you so much! My girlfriend has been helping me with the videos, and it makes her very happy to read such comments;)
great job= you must be the world authority on this
Maybe one day;)
Ackerman's principle is measured with the steering wheel straight head, not at lock.
That's how the geometry of different steering wheel radiius are followed.
If you draw a triangle between both front steering axis (at hub level?) and the centre of the rear axle line, that's the line your steering knuckles should be.
It kinda looks like your front wheels are a little parralel. At full lock, they should look like they point in a visiblely different direction.
Hi, thanks for that. Indeed, I did not calculate the Ackerman correctly. But, then with small adjustments, I reached there. The outer wheel turns less than the inner wheel and I have no scrubbing. Cheers!
that's a lot of intertwined variables - thanks for sharing! nice suspension but gads ... that's gotta multiply the variables too - keen to watch you iterate!
@@JoshuaRobertPreston indeed many variables;) I'm working on the next one and I think it's becoming so much better than this one already.
Thank you for your kind words! Cheers!
Very nice Pedro. You might want to consider the 1 degree toe-in when you add brakes to the equation. Braking force will force the wheels back and create a somewhat unstable situation due to toe-out. I've tested this on my first prototype (way to heavy in the end) and found braking and steering at the same time to be more stable. This wasn't a tilting trike though, but a rigid one with 8 inch front wheels and drum brakes all around
Looking forward to the improvements!
Pjotr (Tesla Tilburg)
Pjotr! Uauu! I hope you are doing well;) And thank you for the comprehensive comment about Toe. I start to understand that it's important for braking and accelerating (things that I barely have at this point;)) Cheers! All the best happiness to you!
Marvelous to watch! Thanks, I’ve been interested in this approach for years. Will be exciting with a 750W motor (or two)
Thank you very much!
Indeed, more power = more fun;). Though, I'm trying to keep this vehicle inside of brackets for pedal assisted vehicles in Europe so max 250 W constant power;)
Cheers!
Wow! Great experiment. I think a "blind" rider would make your outcomes more sciencetifically significant. Still a great endeavor. Thanks
Thank you! Indeed, the results of my experiments are not very scientific. I'm working on a new build and I'm planning for some experiments with sensors to find how much tilt is needed, etc.
Cheers!
What an ingenius testing rig !
Congrats for that idea !
Cheers Kai
Thank you very much! Cheers!
Toe in adds stability, toe out adds quick turning maneuvering. Most rally cars have front toe out and rear toe in
Thank you!
For velomobiles quite some experiments were done, years ago, around 1990. Camber can be made very large without increasing the rolling resistance of the trike (velomobile). With adjusted geometry you can go up to about 20% before noticing increased resistance.
Hello, thanks! Ya, I agree, with round tires you can increase camber quite a lot.
@@pedro-neves You may get unusual tire wear from high camber, as the tire flattens where the weight of the vehicle meets the road. Since this location is off-center, the flattening will be off-center as well, and some tires may not have as much tread/traction at the edges and could wear more quickly. Awesome consequence on a trike, where you can 'rotate' the tires and wear the tread on the other side when the first is used up. High camber matched with tires that have good tread coverage may allow you to get twice as much life out of them.
@@benjaminteasel3942, thank you so much, that i s a great tip! I was considering that, because the tire is round I have no issue with camber but you are absolutely right - most of the tire thread is in the center.
Cheers!
Track-oriented cars usually run about -2 to -3 degrees of camber to improve stability. Also 1 or 2 degrees of to in. Drift cars run serious negative camber on the front wheels to improve front grip during slides as you load up the outside wheel
Thanks! Ya, I can see how that makes sense. Regarding the Toe, What I have been learning is that Toe should just be zero but, often in cars, there is a little bit of Toe designed into it to compensate for acceleration or braking torsion.
Cheers!
You knocked it out of the park with the adjustable geometry ! Just slap a hub motor on the back 😉 . Also bigger wheels might be more forgiving.
Thank you very much! And I already added a motor;) Check it out here if you're interested: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=hKyIqX8F9g3twxFA.
Cheers!
A beautiful job of solving a problem which does not exist on a bicycle. At considerable cost in both money and weight.
Hehe, thank you for the beautiful part;)
Indeed this is more complicated and expensive than a bike. And I love bikes.
This is an alternative. I think it can be made to be safer than a bike and more proper to carry cargo than a bike. I also think that, by making it open source (will start in the next project series), it can be made to be cheaper than commercial cargo bikes. Also, this may help pave the way for knowing how to make a small car (L7 category).
Cheers!
I loved this video sooo much 😅 I could add some of my advice on geometry of the front end but it looks like others comments have covered this, loved your real world testing, am building my own one of these 3 wheeled tilt bikes but with a motorbike engine, swing arm, back wheel and shock at the back, but where mine with differ is that I am building a aluminium tub for sit down position like in an open wheel racecar like F1.😅 Really glad to see this and would like to see your improvements. After you put a motor on it you could actually also have a low seating position right on top of your cargo area lol, cause the lower to the ground you are increases the sensation of speed and lowers the centre of gravity, and you could make it reversible so you could change between riding/driving positions when ever you like 😅😅 really good work
Thank you so much for your kind comment! Indeed I've been getting so much help to improve my design and build! I think that the next one will be much better;)
Regarding the motor and riding position - I'm constrained because I want to have pedals. I'm designing for a class of vehicle that can ride in Europe without license plate (or insurance) - can have motor but only for assisting the pedals, cannot work on it's own.
Regarding your design - sounds awesome! I would just love to see it! If you publish your design somewhere, please drop a link;)
Cheers!
Awesome information! You're very creative. Kind of hard to do in my two-wheel e-bike but it was very informative and entertaining to watch. Thank you!
Thank you very much! That is very kind;) And I'm glad that you found it informative and entertaining.
Cheers!
Amazing project, you getting in the wright direction, and yes this will be a dream with a electric assisted power, though you ever thought about a chainless but a dohc drive to make it a ideal bike
Thank you very much! I already installed assisted power. You're welcome to see in this video: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=-XVDMtRxLR1wAkMe. And I already have ideas for the future.
Cheers!
This is so fascinating! Thanks for all the testing!
Now if I could only learn to weld properly (all my experiments trying to weld up my own cargo bike have been disasters so far! )😊
Thank you for your very kind comment!
And some words of encouraging: I'm also not a good welder. I believe you get there by practicing. I'm also looking forward to doing better, and I'll transition to TIG welding soon.
Makes me happy to read that you are working on a cargo bike build;) If you ever need something, you are welcome to reach out;)
@@pedro-neves Thanks! Greatly appreciated!
Very hood analysis. I appreciate your detail and effort. Thank you
Thank you as well for your kind comment!
The only thing my ocd head noticed was the main shaft hidden was connected to the right only, rather than a dual connection to give a more sturdy control. ( Like the difference between the way a two wheel trailer that connects to the left side only, which gives the rider a herky jerky feel when riding or the Burley Coho XC one wheel trailer that connects on both sides of the hub and the difference is amazing! ). ✌️🌍✌️
Hello and thanks for the tip! On my newest build, I'm trying cable steering: ua-cam.com/video/UWFQ6nFzpgE/v-deo.htmlsi=2XVGCgMp_hvAzU-B.
But if I ever go back to a shaft connection, I'll have in mind the possibility of connecting both sides.
Cheers!
@@pedro-neves Happy to help another fellow cyclist! ✌️🌍✌️
That's awesome! I'd like to build one myself too! Though my engineering skills aren't at your level. What electric motors are you thinking of adding to the bike? Hub? Mid Drive?
Thank you! Building is awesome;) and you can always learn, no rush;) I am currently converting the trike to electric. I will publish the video in a few days;) Cheers!
Travail très instructif.
Merci.
You're welcome. Thank you!
I love the video. -- The detailed approach to all the variables and riding conditions is very impressive. On toe-in, it seems like if 5deg was too much and 1deg was hard to notice, then trying 2 and working up to some limit >=5deg would be worth testing.
Finally, viewing in the U.S. 2024-05-11, I got a pretty offensive ad demonizing immigrants.
Thank you very much! With so many contributions to Toe in comments in this video, I end up concluding that one should aim to have 0 deg Toe. The reason why steering geometries are calculated to have Toe is actually to compensate for deformations or other geometries. So, the objective is always to have 0 deg Toe.
Cheers!
Outstanding efforts! I tried commenting earlier but didn't see it show up, so I sent an email to the account linked in the channel info asking if you might consider using something like Cannondale Lefty hubs for your next front wheelset and knuckle design. It could save you the fabrication time and plot a course to a design which could eventually be implemented by more people.
Hello! And thank you very much! The hub is a very good point. I am designing a new hub that is of the same style as the Lefty. A Few minor differences such as 28 spokes and a left thread for the left spindle bolt so that the wheel doesn't untorque the bolt when riding. I'll answer to your email and share a few pictures. Cheers!
Ackerman is also called "toe out on turns". It's so, as you say, the wheels turn at a different rate on turns, as of course, the inner wheel has less of a circumference than the outer while turning.
Thank you again for the tips! Indeed, I think I understood the relationships between the geometries. In my next build, I believe I'll get the Ackerman right.
Cheers!
Thanks for sharing. Very interesting project you have there. Hope to see the improvements you come up with in the future.
Thank you very much! I look forward to improving it and share the results;)
Lovely engineering step by step
Thank you very much!
Cool project, great presentation, good job on the english too.
Love the flash logo on the front.
Thank you very much! That's very kind;)
What would really tighten that turning radius up would be to have rear wheel steering! I kid 😉Thanks for the fantastic presentation of your process and build!
Thank you very much for the kind comment!
Regarding the rear steering, actually, I tried a cargo trike with rear steering and thought it was awesome! Check it out here if you're interested: ua-cam.com/video/uW5teIGglsE/v-deo.htmlsi=3ylcLOflEAKqAjmJ.
Cheers!
Very nice build. I was thinking about something similar. It will be even better when you get the electric motor in. Plus with the trike set up you can have a larger battery pack :)
Have you thought of having the power come from the rear wheel? You could have a larger motor and less cost. best of luck to you.
Thank you so much!
And yes, I already converted it to electric. Check it out: ua-cam.com/video/9515pv9slyM/v-deo.htmlsi=1EWClM5FcRBzvwr7
Cheers!
If the front wheels are to be unpowered probably -0.5 degree to -1 degree would fine to adapt to small flex and movement. If powered similar amount of not a bit more positive would be good to make up for flex of components. Great bike also great process, testing is always best.
Thank you very much! It's so kind of you to answer the questions that I had to help with my build! It's so nice to share what I learned and also make questions about what I didn't understand and getting great explanations. Cheers!
Camber will make the load uneven, most likely part to straight out break is the spokes as the load isn't shared as well between the sides. If there are stability issues, it's usually better to fix them than trying to compensate for them.
Hello, yes, I do agree that camber creates extra load in the spokes. And also in the spindle.
Thank you! Thank you! Thank you!! You are so valuable!!!
Just to contribute... the toe angle is something that has sense just when the weight of the wheel/suspension system is relevant and/or the power of the engine is relevant compared to the hardness of the materials. In a tricycle or four wheel bicycle you can hold it neutral. But thank you for all your contents
That's incredibly kind;) Thank you too;)
@@Ale_775, and thank you so much for the contribution. It's been a learning process, and it's great when we can make a forum out of it and share each other's knowledge! Nice notes on Toe, thank you.
Thanks to you Pedro, You really did an excelent and useful job! I was speaking with an Audi mechanic the other day and he told me that for a car of roughly 200CV the driving rear wheels have an open toe angle in a way that if you measure the distance between them in the front it can be up to 10/12mm more than in the back if I understood...
45 kilos is very good for a DIY steel cargo trike. I expected something like 60 kilos. Well done!
You changed the geometry a lot. 6 degrees of camber is a gigantic change to 0 Degrees. Many rayle cars don't have that much, even though they sometimes apply a lot of it. Your build is very good, so enjoy it for a while. But maybe in the future you could redo the test with smaller increments.
Thank you so much! Indeed, 6 degrees is too much. I think it will end up with 1-2 degrees. And you are right about the big increments. These experiments allowed to really demonstrate the effect of the changes in the different geometries (exaggerating is like a magnifying glass) and to find the ballpark of where things should be.
Cheers!
Kudos maker I have always marveled after interesting tech
Thank you very much! Me too;)
Toe is generally used to optimize lateral forces produced by the front tires at a specific range of steering and slip angles. I’d assume given the necessity of efficient use of energy; you’d try to match a marginal amount of toe out to reduce tire scrub from camber thrust while going in a straight line. Optimizing your Ackerman is probably a more ideal solution to lateral forces while turning vs toe given the constraints.
Thank you very much! I start to comprehend Toe as a geometry meant to compensate for flex, and also how some geometries affect others.
Cheers!
@@pedro-neves because leaning changes the steering geometry so much have you contemplated the implications of completely decoupling the front end from the rest of the vehicle. Putting a pivot point so the rear can lean independently?(would require an anti roll bar to maintain a neutral starting point on the front)
@@joshmerklin that would be an option indeed. I'm trying to make it work together because I want it to behave as much as possible, like a bike.
@@pedro-neves Understood. Simplicity is rather important in many cases!! Have you looked into how Yamaha does their linkages on the Niken? For some reason It slipped my mind when I was commenting on this that it even existed.
@@joshmerklin, I looked both at the Yamaha and the Piaggio MP3. I think I've been looking at anything with two wheels in the front for the last few years and my creations end up being a result of that mixed with my own thoughts and of course the contributions and thoughts that are shared with me, such as yours;)
I think the toe angle will have an impact on high speed cornering and stabilty when slip angles start to come into play, but you're not going to gain anything at the speeds you're doing. It also causes scrubbing of the tyres, which you noticed as resistance at extreme angles, but is still there creating drag at low angles.
Likewise camber will create some scrubbing and increase drag as you are effectively riding on cones which want to roll in circles. If you get noticeable gain in stability though it's probably worth it.
For the steering, rather than a T bar shape central pivot to move the steering rod joints outwards, you could use 2 central pivots linked by another bar to make a parallelogram mechanism?
Hello and thank you so much!
Agree with Toe - will be 0 deg because there is not sufficient vehicle dynamics to make sense to calculate Toe.
After multiple feedback, I start to think that camber will be 0 to decrease forces that are not perpendicular to the structure.
The parallelogram - Yes! Recently, someone that watched the video sent me some drawings explaining how the parallelogram would fix the issues that the T introduced.
Thank you so much!
Cheers!
@@pedro-neves I think a small amount of camber (0° to 2°) shouldn't generate significant disadvantageous forces, but if you get a significant improvement in stability and feel then it's worth it.
@@jamescarruthers1967 , exactly. I think I may end up with 1 deg ish just to feel like I added that extra bit of stability;)
Great project, looks like it will be very efficient.
Thank you very much! I think so;)
Toe in and out is all about tyre wear. "toe' on cars simply compensates for driving or non driving wheels, so that it drives parallel to the road while driving (zero toe in). Front Wheel drives want to bring the wheels together (so needs toe out to start with). Read Wheel drive, the front wheel gets pushed out and so needs toe in to start with.
Understood, thank you very much! Indeed, I'll tune for 0 deg toe.
Cheers!
Great work, Pedro. Thanks for sharing your findings!
Thank yo very much! Ans you are welcome;)
ตรงจุดประโยชน์ที่ได้ใช่สวยงาม😮..ดีไซน์จะตอบการใช้งาน❤
Thank you! Greetings!
traditional bikes have a metric called 'rake' that describes the offset of the front wheel from the steering axis, it stabilizes the bike. Tire contact patch behind steering axis and wheel axel in front of steering axis (rake) for stable handling.
Indeed, I did not consider this aspect of the geometry and it's stuck with me. I will have to test it one day.
Thank you!
@@pedro-neves Thanks for the response, you're doing excellent work. I do think that a little bit of 'rake' will stabilize the trike for hands free riding. Axle in front of steering axis means the steering tends to self straighten (assuming there is some 'camber').
@@pedro-neves The steering assembly naturally wants to find it's lowest possible state. 'Rake' ensures the lowest state is straight ahead.
@@H3XM0S ya, totally agree. I will try it out.
@@H3XM0S I definitely agree with you. Thanks for the contribution. I appreciate it very much!
Where did you get the hubs for this fantastic project?
Thank you very much! I made the hubs;) I have a video just about that: ua-cam.com/video/sU2ZS7Nlbj0/v-deo.htmlsi=gPJPbeqmm7bXMFMa.
The next iteration of this project will have new wheels and wheel hubs that I'm working on.
Cheers!
Sorry, I have to say I already know that toe-in is not a function of preset geometry, but a counter to flexing geometry. Ideally toe-in would automatically counter whatever geometric flex was caused by whatever weight caused it. So toe-in is only a work around to flex.
The best way to anticipate a certain toe-in is to put on the entire weight of rider & cargo, introducing the geometric flex, & zero up the toe-in-out while under load. After removing the load, whatever toe-in results is correct only for what that load was.
Thank you so much! Indeed, I have learned this in the meantime. I now understand with the kind help of people such as you that the aim is to have the Toe to 0 and that designing Toe into a vehicle is thought of to compensate for flex.
Cheers!
you are a real scientist !
Thank you;)
To get the Akermann steering correct, you need to have the tie rods level with their pivots, as you had to move the steering mechanism back to accomodate the castor plates, it's always going to be a compromise. The other issue you're finding is that the steering mechanism is a T bar, so it turns the T which alters the spacing of the tie rods, again, this will be better with the T being central to the steering tie arms. It would also be best if it slides rather than turns, but this is quite difficult to do while having the steering link to it.
Hello, thank you for sharing that analysis! Ya, the T does change the steering geometry, but I had to put it because I have bump steer (when tilting) without it. The T can be smaller once I get rid of the castor plates. And also, when I remove the castor plates, I'll be able to have the steer pivot parallel with the tie rods. It's easy to make the drawings for Ackerman but once all these adjustments start to pile up, then it becomes different.
@@pedro-neves yes totally get that, what you can do to help when tie rods are in line is create a parrallelagram using 2 pitman arms, the just use the existing steering arm to drive one of the pitman arms. That should sort the over-angle and bump steer issues in one go. 😁
@@overlandready, pitman arm! I didn't know what it was until you told me about it and I went searching. It's super cool to make something, share and have people helping me to make a better one! Thank you for that!
Wow idea brilians... Hebat sekali bro sepedanya bisa membantu pekerjaan. Bukan hanya dipake pergi bekerja.. 👏👏👌🤝🤝🙏🙏🙏
Thank you! Cheers!
Hi Pedro, thank you for your job, well done, i learn a lot . have a god day.
I'm happy to read that you liked it! Thank you for your kind comment;) Have a great day!
2points camber to 1 point caster active motion 2-1 ratio or 3 to 1 for lower speed steering stability vs control vs °s of motion. Use ball joints on your tie rods. The use of an A arm usually a lower one would ensure accurate camber caster motion decreased drag ect
The Ackerman principle is at any point of turning, the axis of all three wheel will meet at one point… set it in a way at full turn , the axis of both front wheels will both meet, along the axis of the rear wheel… check with the kenimatics of motion…
Thank you! Indeed, with this geometry, the Ackerman principle is achieved in most of the range of the turn but not in all. I believe the next build will have all the Ackerman principle corrected.
Cheers!
Whatever your used to will feel best. After returning to cycling after riding a heavy motorcycle, I literally couldn't keep the bars straight. It takes time for your brain to adjust to the new feeling and sensitivity.
I totally agree! When changing many things, it's hard to know what "feels" better. I try to have some standard tests to make things a little less subjective.
Hey, just found your channel and I love what you do. I can't offer any advice on your mechanical design, but for your experiment design I recommend looking into orthogonal (Taguchi) arrays - it's a way to test multiple variables and how tbey interact much more efficiently. As others have suggested caster and camber tend to work together, and this would be the way to find the right setting in a greatly reduced number of experiments.
Hope this is useful!
Thank you very much! That helps a lot! And you are right - testing every setting against every setting would be very time-consuming. I also came across this video that explains very well your suggestion: ua-cam.com/video/5oULEuOoRd0/v-deo.htmlsi=rYvmZocl1xeetJy5.
Cheers!
Do you think you could make the front wheel distance a bit smaller for better city maneuverability?
Hello, good question, actually it's already narrower than common cargo bikes. This trike is 70 cm wide and it's common for cargo bikes to have 1 or 2 more cm more.
Cheers!
Alright, but I see it in comparison with a single front wheel. Maybe there could be a good compromise.
@@JohannesSchmitz yes, I agree. The compromise that I was thinking about is - being narrow enough to go through most places and traffic, while having the added stability of a trike. I was somewhat inspired, e.g. by the Piaggio MP3.
you might want to try camber and caster together at higher angles.
say 20-30° of caster with 2-4-6-8° of camber.
you dont need to remake the arms for that: just lower the suspension, so the arms droop lower. just doing that will increase camber with your current geometry.
30° is close to the typical steering caster angle (also called rake) of a bike, which is between 24° (super agressive, seen on time trial bikes) and 34° (super slack, seen on downhill frames as it helps absorb landing hits and maintains stability with the bike at full droop, when the fork is fully compressed)
the caster angle needed is relative to the wheelbase. the longer the vehicle, the more caster is needed to help reduce the turn radius.
as far as my research go, toe helps adjusting the ackermann, combined with caster and camber. you can see it dynamically change as you steer on the final form of the bike. that's the direct effect of having close to 40mm of scrub, something i will explain later.
you might want to make a new camber plate with 5 degree increments, something you can easily do by drilling a new set of holes closer to centerline.
and when making the new steering hub, since you're making your own, could fit *around* the knuckle.
the closer the knuckle mounting axis is to the center of the wheel, the easier it will be to adjust, and you will have less scrub (the wheel will travel less relative to the pivot center) and dynamic toe out when tilted to the max (as the wheel is closer to the knuckle).
in automotive terms, this is called positive offset. your car has positive offset, it is called ET in wheel terms. should be between +35 and +55, usually.
that can be done with a virtual center wishbone (but that is extremely complex since you have tilt steer on top of double wishbones) : instead of 4, 3 point wishbones, you have 8 links, who work in pairs. the space between the end of the links at the knuckle, relative to the space at the frame, deports the steering center to and from the wheel centerline.
and you can weld together these pairs at the wanted knuckle offset to spread evenly the suspension load.
this means you can forgo the camber plate, as you can effectively change caster as you change the virtual pivot's location... yeah it's going to be a little bit complex to read, i know.
you can see one being made on this channel: www.youtube.com/@councilhousecreations8035
the lad at council house creations had to do that because he's making a 4 wheel drive gokart... no room for a conventional knuckle close to the wheel center.
you can see this principle of a virtual steering pivot on a few 2 wheeled cargo bikes, like some of veloma's, the catan titanium frame from a few years ago or the EScargo, where the caster and the angle relative between the frame and the knuckle create the wheel's trail and caster.
to not mix with bikes like the ketter cargoline, which run a pivot inside the wheel with a fixed swingarm, something seen on some motorcycles too, like the bimota tesi, vyrus 985 or yamaha gts1000.
Thank you so much for the very complete set of tips!
There are so many things about the geometry and I keep learning from the community, such as yourself, that clearly has knowledge on automotive geometries!
I try to compile all the advice that I get and put it into the next iteration as much as it fits the amount of changes that I'm making;)
I plan to make this easier for the community, actually. I will finish this series and then start with an open source project where I share the files in a very organized way, with versions, in editable format.
It takes some time because I don't do this full-time, but I hope you will comment on the next iterations or even edit the drawings when I start sharing;)
I will also look into those creations in the UA-cam channel that you shared.
Cheers!
😊прекрасная разработка.
Thank you!