How to Replace Pitman Arm 2000-06 GMC Yukon
Вставка
- Опубліковано 25 сер 2024
- Buy Now!
New Pitman Arm from 1AAuto.com 1aau.to/ia/1ASP...
A bad pitman arm can cause poor steering response, wandering, pulling and uneven tire wear. It can also be dangerous. This video shows you how to install a new pitman arm on your 2000-2006 GMC Yukon.
• Check here for more videos on the 2000-06 GMC Yukon: • GMC Yukon 2000-06 2nd Gen
This process should be similar on the following vehicles:
2000 GMC Yukon XL 1500
2001 GMC Yukon XL 1500
2002 GMC Yukon XL 1500
2003 GMC Yukon XL 1500
2004 GMC Yukon XL 1500
2005 GMC Yukon XL 1500
2006 GMC Yukon XL 1500
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oa/1AXA...
• Pry Bar 1aau.to/oa/1AXA...
• 16mm Wrench
• 18mm Wrench
• 8mm Wrench 1aau.to/oa/1AXA...
• 11mm Socket 1aau.to/oc/1AXA...
• 15mm Socket 1aau.to/oc/1AXA...
• 21mm Socket 1aau.to/oc/1AXA...
• 22mm Socket 1aau.to/ob/1AXA...
• 34mm Socket 1aau.to/oa/1AAS...
• 7mm Socket 1aau.to/oc/1AXA...
• Pickle Fork
• Pitman Arm Puller
• Pliers
• Side Cutters
• 1/2 Inch Air Impact Gun 1aau.to/oa/1AXA...
• Ratchet 1aau.to/oc/1AXA...
• Torque Wrench 1aau.to/oc/1AXA...
• Drill
• Cotter Pin
• Hammer 1aau.to/ob/1AXA...
• Vise
Subscribe: / @trq
Check out our playlist:
GMC Yukon 2000-06 2nd Gen: • GMC Yukon 2000-06 2nd Gen
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Back out the lower 2 bolts on the steering gear box and then loosen (but don't pull out) the upper bolt. They are 21mm's. Doing that allows you to rotate the box and get the pitman arm puller in there without having to do all the complicated removal.
Is it necessary to remove all that stuff? There’s gotta be an easier way.
What is the name of that part that the pitman arm was attached to?
Thank you awesome video very helpful and the details..
+Ericks Melendez Thanks for watching our video! 1aau.to/m/Shop-TRQ
is there a part number for that steering shaft bolt? Im going to need one.
Watched a few videos in preparation for doing this on my truck. This is the only one I’ve seen that involved removing the steering box. Is there a reason for completely removing itvs just loosening the 3 bolts?
I think they did it to be able to "vise" it and torque, ill just leave mine on and use the same breaker bar tension off to install lol.
Thats how GM has it written in the FSM
You absolutely do not need to remove the box 10x more work
Don,t worry he will charge more. Be couse the custumer was there with him.. good job..
Less work when you don't have to mess with the pitman arm puller on a free swinging steering gear.
Its one more bolt and two hosess not 10x
So do these vehicles have one or two pitman arms? Also is there one or two idler arms? Took mine to the shop they said I needed each of them the idler and pitman replaced, but if there's 2 on each side they didn't tell me.
1 pitman..1 idler
Pitman is driver side, idler passenger side. 1 each