Modernizing my Porsche 964 Engine! (Should have came like this!)
Вставка
- Опубліковано 5 сер 2023
- ShopJimmyO.com
Support the build!!
/ jimmyoakes
/ jimmyoakes
Send some sub mail!!
Jimmy Oakes
PMB 169
61 N. Plains Industrial Rd.
Wallingford, CT 06492 - Авто та транспорт
Jimmy stays being the most laid back chill but mad informative YT'er
- feel like the Porsche engine is part of the evolution
Right?
The glazing is wild
@@dcskate1022 Krispy kreme ?
Jimmy mayne at it again
For real, he's about the most laid back UA-cam car guy I've seen and the detail he describes with is easily understood
This is modern hot rodding. Great job on attention to the details, the thorough walk through, and improvisation in the build. My 5 yr old loves this as much as me. Great stuff Oakes team.
Right?
A whole video on Jimmy teaching us wiring? I couldn't be any more excited! The techy nerdy "boring" stuff you go over is my favorite part of your channel. More of it!
he has done one in the past about a year ago. its very informative
@@Swigester But we need mooooooore
Cant wait how this will look in the car, the difference before/after is crazy.
Right?
Coils - use the valve cover spacers, add a thick bar (alum or steel) to tie the spacer together...drill and tap bar to use the coil mounting hole
Or he can press some aluminum spacers in the tubes
And the height you could trim the rubber tube…
The best video thus far. Are you going to use the current DME control unit for all of the new components you have installed?
Omg yes. I've literally paused the video while he's bolting on those stupid fingers just to post this exact same thing.
One bar across. You could even CNC it out all fancy if you wanted... Send cut send. Etc.
And then the coil packs would just bolt to them.
Also a nice ring underneath each one would be a good idea while you're at it so that there's less junk that gets in the spark plug hole there since it's not going to be sealed off in this motor is low and next to the ground
Also for AC… I would look into converting to electric AC (if budget allows)… the AC on these old cars is almost worthless. With electric you’ll get a colder cabin and not have the power loss. It is kind of a pain to convert it though, but seeing you already have the car torn apart it’s a good time to tackle it.
Looking KILLER!! Can’t wait to see this thing ripping
NGK TFSI Coils from R8 etc. would be also a good option, there are short and long ones
Stoked to see the bro guy in your videos. He's a top notch dude. Good old kiwis
As an older Porsche owner, I'm loving watching a young fella doing modifications to an older Porsche, make it yours, I do like the colour, Rj in Oz
Imagine having friends from another country come over and help wrench on your car. Gotta love the impact Jimmy makes on people. I’m not the brightest but I’d love to lend you guys a hand one day, although you probably wouldn’t need or want the help. Hope you open a workshop sometime, I’d send my mk2 gti over to you in a heartbeat for a link ecu install.
Down the road if you end up wanting PS on the porsche, recommend looking into a MR2 Spyder or Volvo electric pump so you can just mount it in the front and make short lines to the rack.
On the coil part, look at the VW 036905715f coil, quite short, fit the sr20 nicely.
I'm a Porsche tech and do a lot of air cooled service and repair. Loving this build
You have the tabs, and you have a fabricator, Do a your own coil bracket, easy some metal and weld, and make it 1 color!
Las Vegas tools has a slide hammer attached to a vise grip. Top 10 tool investments of my life
Everyone give Jimmy love when he does the wiring videos he needs it they are very informative
You should make some little billet brackets that bolt the coil into the hole itself and look nice then sell the kits 🤘🏼
I love this build series so much. It's the perfect balance of informative and entertaining, and I really can't wait to see what the car runs like when it's done.
Killing it Jimmy!
Read a little more into Twin Spark Jimmy, it's actually quite useful technology. The fact that you can control them far better than the old distributor tech that was on there makes it even more interesting, I'd be interested to see what finetuning that secondary spark on the dyno can do. Turn off those secondaries along the way in the name of science and I'm sure you can notice the difference.
Awesome seeing Guy in a Jimmy video
This channel got even better with Porsche content🔥🔥🔥
love the aircooled content so much
3D print some adapters and holders for those coils. Could be a cool product for you to sell.
It’s so funny. I’m an aircooled beetle guy and it’s all pretty much the same problems and jank that the beetles have but massively more expensive. I really don’t want to know what he paid for the oem fan shroud. And you can buy brand new engine tins or used tins for a beetle for a few bucks. It’s really interesting to watch these videos from this perspective
Good call on changing the pulleys to serpentine belt style, fits with the aesthetic of the fan shroud being ribbed.
Good midnight ya'll patreon pals!!! Let's gooooo!!!
Link babeeeeee!!! Oh I can’t wait to see the finished product of this one 👍
All the goodness that it deserves!!
Patreon gang!
200 views in 12 hrs? here come the real views (noti gang)
Great video I have a 91 964 so it's very cool to see inner workings. Can't wait for Dyno Run !!!
Talk to sharkwerks, emory, you got a lot of things to do, dont over complicate things.
Love the content!
Bringing the 964 up to date is some great content! I restored/rebuilt my Seafoam Green 63 Merz Benz 220Sb 20+ years ago. Your post makes me want to re-explore some new Tech for at least maybe the ignition system, keep up the great content Oakes-Garage!
I LOVE THE WIRING VIDEOS
I like all your videos but this is a great video! Love the Porsche content. You answered questions I have had about these motors and upgrading them. Excited to see you drive it with it all dialed in.
BIG 500K FOR JIM AND THE CREW LETS GOOOO BABY!!!!🎉🎉🎉🎉🎉🎉🎉
Have Master Spoon weld an aluminum bracket that cover all 3 coils with tabs that branch down to the bolt holes that you are already using. But repeat it 4 times and mark them where they go on the engine. Similar to what DW fuel rail that you got for the LS with out the fuel.
How you know I'm a regular viewer until the very end. It has been approximately 13 videos since ol Jimbo got the send off right. You know the deal, like content and scrubscribe. Stay tuned for comments. Have a good morning spoon
Do the spark plug tubes from the old wires fit on those. You can usually separate the head from tube and swap the center tube and either shorten the wires or coil them up in the tube.
Stoked to see guy is there 👌 sending love from New Zealand
21:53 that was such a satisfying sound
Good murning PATREON gang. Porsche content you say? Let’s go!
Just here to say I'm proud of you Jimmy.
Wiring videos are great. It's just something I can toss on in the background and work. Probably work on wiring as well.
Was cool seeing and learning how to set a link up on something that old.. thanks
Really liking the music lately, and the editing has been on point. Great work guys, the Porsche is going to be a work of art!
Make a billet piece that can fit in between the valve cover and the coils make it fit more nicely 😊
Really cool to see you modernizing this engine. She deserves it!
Beautiful work with the engine and accessories so far, I love seeing people taking their time and really going through the build.
The work you guys do just blows me away. That motor looks beautiful Jimmy!
Your team is really solidifying. Your content is always entertaining and informative. You are doing the "Thing" Jimmy Oakes. Thank you very much!!!!
Can't WAIT for the wiring video!
Paint those coil clamps black like your valve cover… that will make them “disappear” a little better and look better.
@MrJimmyOakes.. OMG I won!!!! TYSM!
@MrJimmyOakes.. OMG!!!
Aww it's already over. It felt like a 5 min vid when it was a 28min vid. Epic
24:23 OG’s remember Jimmy’s MK4 with monster green wheels 😂
Looking awesome can't wait to hear the difference when its running properly. And Guy finally popped up
In the future, fill the flutes of the drillbit and tap with grease to catch metal removed.
Happy to see all the progress on it happen so fast
Epic work Jimmy! I'm loving this series.
You're probably going to want to find some grommets to seal the coils to the heads, so junk doesn't end up in there. Could fall in the cylinders when you change the plugs. I'd also red Loctite that cam position bolt.
Maybe 3D print a bracket to hold the coil packs. There’s higher grade materials that can withstand engine bay temps
Buzzy seeing the kiwis in the mix again! Nice work cuzzies!
Jimmys content is so relatable that I even feel I can drill my imaginary 964 cams!
Props to jimbo for handling this Porsche build like a boss! All the random little pieces would of freaked me out lol
Got this 46mins late but still watching. Love the vids 💚
Absolutely love the Porsche vids man! And can’t wait for the wiring vid!
3D print some spacers for the coils so they center and sit flush to the hole
You gotta love Austen random giggles during the vid.
This Ls36 is gonna shread....
Nice work on the boxer engine.
Greetings from South Africa 🇿🇦
These porsche engine refresh videos are the most satisfying ones I've ever watched
A place called Patrick Motorsports makes a billet coil on plug bracket for $250/pair. It's chrome which isn't ideal but you could powder coat it black to match the rest of the billet parts.
Shout out to Steph with the subtle Burger King!!! Have it your way girl!
Your the most humble human being i've ever seen on you tube. I really hope I can meet you and the crew one day!
Love these 20+ minutes of jimmy and the gang🤙🏼🤙🏼
the engine came out super clean Jim!
Oooooh, the Porsche engine's looking CLEEEEEAAAAN!! Shout out to Guy n Steph, uo the kiwi's 💪🤙🏼
Also, peep the Cedric tee 😍
Porsche content hits different!!! Keep them coming!!
i like this build more then any one you had yet on your channel! great job!
love the color choice on the fan
seeing this thing get refurbed has got to be the most satisfying thing you done on the channel so far keep it coming
Fdf might be able to design and make a nice billet bracket for the coils . But if im not mistaken you can shorten coils .
This is coming together great..... it takes me months to plan out my build and this dude does it in weeks.
I watched this twice already ! GO JIMMY
I learned soo much from this video while still being well entertained
What’s up Jimmbo 🤘🏼
You should have someone 3d print grommets to fill the space between the coils and the valve covers!
That thing is gonna be SO good!
By far best car youtuber out there. Styling wise and actual build quality. Keep killing it man!
I'm in love with the 964 content! I can't wait for the turbo kit! Also, look at getting an Accusump for the E36's LS!. They're relatively inexpensive and provide that little extra insurance, so you don't end up with Rodney knocking on your wallet!
Came together nicely and cant wait for the wiring video. 🤙
Well done looks so good 😮
Best UA-cam channel by far. The variety of content is unreal and it's always good content. Im hanging out to see the ae86 drifting
GUY! Such a solid dude. Been subbed ever since his first appearance on this channel 🤙 Welcome to the States brotha!
#CommentForTheAlgorithm
I’m so excited for this project to finish up
just sick how one video has so many information!keep it up jimmy🔥🔥🔥
Nightshift 🤝 jimmy Oakes
Make a spacer plate for the coils and power coat it black it will blend in
Cannot wait to hear it running. But also can because than we will get less videos of it sadly
Man that engine looks so good!
Great work Jim!
Lets gooo... Im ready for a lambo evo... Or a EVo8/9/10... Full faith in Jim. Past/now/future Oakes Garage... 100000000000000000000000000000000000
Brilliant!! Good stuff sir 😮
It looks so good.