Thanks for tuning in mate 🍻 yeah it made for a much simpler removal of the motor since we didn’t have an engine crane. It also allowed us to easily unbolt the transmission without having to remove our cabinetry, bed and floor from the van.
Honestly mate it’s so hard to find half decent parts these days! Without taking the risk of buying Japanese parts of old vehicles from wreckers, made in china parts are all that’s available online. The best thing you can do is head into an old school independent parts supplier. They’re gonna have the contacts and the ability to hunt down rare spares. Repco parts will work fine for the easy to replace parts like fuel pump, water pump ignition system (distributor, coil…). As for internal parts, if you have original Japanese look into getting them machined first rather than replaced eg. crank shaft, cam shaft block and rods. The blokes that machined the block and head were also able to hunt down American made piston rings and hydraulic lifters, again, whoever you get to machine your internal parts are gonna be in the know for better quality parts in that department too
Great job guys! My wife and I have a 1989 hiace . Looking at doing the same thing. Did you rebore the block to get more power? Did the new carby give it more power? Thanks :)
Get keen mate, you and your wife are gonna have a cracking time. So we didn’t need to completely rebore the block, we just honed it out 60thou and fit oversized rings. If your block needs it however, I did find another larger oversized set of rings and bearings to save you buying bigger pistons. I don’t believe the rebuild gave us a massive boost in power but more the fuel efficiency. As for the Weber carburettor, I couldn’t speak more highly of it. Since its throats are almost twice the size of stock, it definitely added noticeable power. Especially in the low rpm and when your vacuum advance is one. I’ll flick you a message on insta for more detail 🍻
Yeah awesome! Right well if it has the original Japanese Toyota carby and it’s giving you any issues, I highly recommend getting it rebuilt with new jets, needles and seats. I went down the path of replacing it with a Chinese made replica carby and it was a huge piece of sh!t. If you’re looking for a power upgrade though, spend the money on a Weber Dgav 32/36 carby which is the one i use. It will massively increase your low end power and give the whole throttle a better feeling power response without affecting fuel consumption. It also removes a lot of the overly complicated emission control systems making it more reliable. Only downside over the stock carb is the Weber does not have a fuel cut solenoid so to prevent the motor running on you will need to turn the engine off in reverse gear for an auto, or stall it out in 5th gear for a manual. Let me know if you have any other questions or want me to go further in depth 😄🍻
You’re much better off rebuilding the original Japanese motor, especially if you’re going for longevity. The new motors are rubbish ‘made in china’ replicas and won’t stand the test of time. It’s definitely cheaper to do the process yourself, cost us roughly $3k. However to pay a mechanic would set you back approximately $6k (that was one of our quotes)
Your Van are very nice and excellent work filming very well. your machinal guy very nice to you helpful. My van Motor may gone sooner, Hard to start cold early morning, black smoke at back exhaust only early morning, black marks on the driveway spot. Oil level still full and water no leaks, Too much fuel goes in engine, may black smoke, only on the driveway as spot black marks , NO White Smoke my only 110k km low 1996 model. Or do need new fuel regulator spare parts? Engine still run smooth. Should stop driving now on. Machinal need to checks. What cost your machinal to rebuild motor like yours, how many hours to do rebuilt motor. I seen too many brand new Cylinder heads bare motor on the eBay?
Yeah I’m very lucky to have a father with mechanical knowledge. Made it an easy decision to attempt the rebuild myself. As for your van, black smoke would definitely indicate a rich fuel mixture. Assuming your van has fuel injection, maybe it’s cold start system is increasing the fuel rate to much, cause an over rich mixture cold start. Our whole rebuild, cost us ~$3500 including a bunch of new parts and machining. I’d recommend taking your head and block to a workshop and getting them to check if it can be decked and bored as anything you buy on eBay with be cheap made in china rubbish that won’t last
@@theseroadsweroam Thank you for let me know, wow your dad help you very lucky, and big nice garage building. My Van 1996/Jan RHZ125r petrol Carburettor, only 110,000km original, friend gave van to me was 51,000km 5 yrs ago, Mechanical did oil changed regular but never clean Carburettor, air filter. had flushing out coolant 80k km, My mechanical local guy came my place, oil changed, Carburettor buttery fly was jammed, he spray by w40 can, and screw to low ide, it was engine running too fast. 2 weeks ago, oil still bit black only travel 200km two trips. Mechanical guy told me engine running fine and easy start, black smoke still on driveway marks. Yes you are right my van rich fuel mixture too much, I smell it from exhaust. I booked my another local mechanical already for next week Tuesday, if he able to fix or not? He does service old cars with Carburettor . Can you please ask your dad, which spare parts I need to replace for fuel rich mixture, Do I have to buy new fuel regular pressure Or should I buy brand new Carburettor rebuilt from eBay seller must be from Australian. May cost $350. or Should I buy 4xFuel Injector Fits Toyota Hiace RZH103 RZH113 RCH12 RCH22 2RZ-E 2.4L 1995-2004 was listed Ebay, cost $85,? Should I buy from Repco should I buy new air Filter and new petrol filter? My van only original 110k km low. Thank you for reply me ASAP Today I am taking van to another mechanical to check fuel rich mixture.
Perfect, just wish you also cleaned up and serviced the transmission. They may say 0 maintenance from factory assembly but like the differential gear oil, they need their oil to be replaced every 15-20 years. Along with cleaning the shrapnel magnets. The magnets could also be replaced or recharged.
Hey mate, yeah after cleaning the engine up and slapping the two part together it did look a bit unloved. But rest assured i’ve serviced the tranny every 12 months just to make sure it’s turning over right, being an auto I like to make sure the oil is always fresh and pan valves are clean. Yet to find any metal in it so he’s turning over beautifully. Thanks for watching, cheers 🍻
@@theseroadsweroam Awesome, cheers mate! A great wall wingle 5 has this engine with fuel injection, dubbed 4Y-E. Same stock engine, with multi-point injection intake manifold at the same position. So larger parts source. I will be changing mine to a carburetor for easier fuel swapping and decoupling as much electrical from my combustion cycle.
Yeah right, well I guess they still make 4Y motors in china now for use in forklifts because of their ability to run LPG so makes sense GW is onto it. I love my carbys personally, grew up on dirt bikes so been around them more. Only thing I’d want to look into changing is the electric distributor ignition system that came out on the 3y engine of the time but that’s more money
Why not put V6 Commodore Engine much stronger, company doing at Moree NSW, Van need new metal bracket, new petrol pump fit back tank, new wirings kits, Cost approx. $7000 Dollars Approx., plus delivery van to Moree and return van back to you, but Van need new BLUE SLIP, New different Motor, Registration Office have to Approve and Reweight Van as KG. OR Electric Motor, run by Batteries Electric Vehicle, No service needs for 50k km no petrol or no oil needs save a lot. Van old 19th century machinal has to pull all out and install 21st century Electric Motor in.
I have seen these vans with ecotech commodore motors in them, however our van was built to have this motor in it and the process of an engine swap was not a viable option for us as we wanted to be back on the road ASAP. Also for us, the cost of an engine swap, petrol or electric would cost more than what the vehicle is worth.
Wow cheers from the us ! I have a 88 cargo and you taking the motor out the bottom with the head off is very very informative thank you for this!
Thanks for tuning in mate 🍻 yeah it made for a much simpler removal of the motor since we didn’t have an engine crane. It also allowed us to easily unbolt the transmission without having to remove our cabinetry, bed and floor from the van.
She's good as new great job guys
Yeah we’re super happy with the job we did. We were finally able to get ontop of all the issues we’ve been having since our adventures beginning :)
Awesome. Great Dad. Hope all good now. Enjoy resumed adventures you 2.
Thanks Mate, we plan to travel into outback QLD very soon 😁🍻
Good work guys. Hope you’re back on the road again soon.
Hopefully the cooling system can keep up
How epic! Thanks for sharing the build
Thanks for tuning in mate 🍻
Great job Roamers. Great to see you arent put off by setbacks and plough on ahead.
Good on ya Russ! Yeah we’re super happy with finally getting through all this drama. Now it’s time to get stuck back into it 🍻
We will Roam another day 😁
Good looking dog 🐶I’m sure he was helpful. Very professional job. Well done 👍
Young Boots, two years old but three years into his apprenticeship 🔧
Great video mate! Looking at rebuilding my 4Y in my 88 hilux. Where did you buy the parts from ? I can only find cheap eBay Chinese crap
Honestly mate it’s so hard to find half decent parts these days! Without taking the risk of buying Japanese parts of old vehicles from wreckers, made in china parts are all that’s available online. The best thing you can do is head into an old school independent parts supplier. They’re gonna have the contacts and the ability to hunt down rare spares. Repco parts will work fine for the easy to replace parts like fuel pump, water pump ignition system (distributor, coil…). As for internal parts, if you have original Japanese look into getting them machined first rather than replaced eg. crank shaft, cam shaft block and rods. The blokes that machined the block and head were also able to hunt down American made piston rings and hydraulic lifters, again, whoever you get to machine your internal parts are gonna be in the know for better quality parts in that department too
@@theseroadsweroam roger that thanks mate!
@@Steddywelly try toyota material handleing mate this engine is the main one they use, i cant see why the parts can be diffrent
Great job guys! My wife and I have a 1989 hiace . Looking at doing the same thing. Did you rebore the block to get more power? Did the new carby give it more power? Thanks :)
Get keen mate, you and your wife are gonna have a cracking time. So we didn’t need to completely rebore the block, we just honed it out 60thou and fit oversized rings. If your block needs it however, I did find another larger oversized set of rings and bearings to save you buying bigger pistons. I don’t believe the rebuild gave us a massive boost in power but more the fuel efficiency. As for the Weber carburettor, I couldn’t speak more highly of it. Since its throats are almost twice the size of stock, it definitely added noticeable power. Especially in the low rpm and when your vacuum advance is one. I’ll flick you a message on insta for more detail 🍻
I own a 2004 toyota hiace but my caburator is different from joey's and i'd like upgrade any advice 🙏
Yeah I’d love to help! Do you know what motor is in your van? I ask because a stock 2004 vehicle would have EFI not a Carby
If you look in the owners manual, check if your engine code is 2AZ-FE
It might also be stamped on the engine block or compliance plate
Engine code is 4y
Yeah awesome! Right well if it has the original Japanese Toyota carby and it’s giving you any issues, I highly recommend getting it rebuilt with new jets, needles and seats. I went down the path of replacing it with a Chinese made replica carby and it was a huge piece of sh!t. If you’re looking for a power upgrade though, spend the money on a Weber Dgav 32/36 carby which is the one i use. It will massively increase your low end power and give the whole throttle a better feeling power response without affecting fuel consumption. It also removes a lot of the overly complicated emission control systems making it more reliable. Only downside over the stock carb is the Weber does not have a fuel cut solenoid so to prevent the motor running on you will need to turn the engine off in reverse gear for an auto, or stall it out in 5th gear for a manual. Let me know if you have any other questions or want me to go further in depth 😄🍻
Helo God bless you
🙏🏼
Looks mint do you think it was cheaper to rebuild urself Ive seen new engines for sale in aus for 2.2k.
You’re much better off rebuilding the original Japanese motor, especially if you’re going for longevity. The new motors are rubbish ‘made in china’ replicas and won’t stand the test of time. It’s definitely cheaper to do the process yourself, cost us roughly $3k. However to pay a mechanic would set you back approximately $6k (that was one of our quotes)
Your Van are very nice and excellent work filming very well. your machinal guy very nice to you helpful.
My van Motor may gone sooner, Hard to start cold early morning, black smoke at back exhaust only early morning, black marks on the driveway spot. Oil level still full and water no leaks,
Too much fuel goes in engine, may black smoke, only on the driveway as spot black marks , NO White Smoke my only 110k km low 1996 model. Or do need new fuel regulator spare parts?
Engine still run smooth.
Should stop driving now on. Machinal need to checks.
What cost your machinal to rebuild motor like yours, how many hours to do rebuilt motor.
I seen too many brand new Cylinder heads bare motor on the eBay?
Yeah I’m very lucky to have a father with mechanical knowledge. Made it an easy decision to attempt the rebuild myself.
As for your van, black smoke would definitely indicate a rich fuel mixture. Assuming your van has fuel injection, maybe it’s cold start system is increasing the fuel rate to much, cause an over rich mixture cold start.
Our whole rebuild, cost us ~$3500 including a bunch of new parts and machining. I’d recommend taking your head and block to a workshop and getting them to check if it can be decked and bored as anything you buy on eBay with be cheap made in china rubbish that won’t last
@@theseroadsweroam Thank you for let me know, wow your dad help you very lucky, and big nice garage building.
My Van 1996/Jan RHZ125r petrol Carburettor, only 110,000km original, friend gave van to me was 51,000km 5 yrs ago, Mechanical did oil changed regular but never clean Carburettor, air filter. had flushing out coolant 80k km,
My mechanical local guy came my place, oil changed, Carburettor buttery fly was jammed, he spray by w40 can, and screw to low ide, it was engine running too fast. 2 weeks ago, oil still bit black only travel 200km two trips. Mechanical guy told me engine running fine and easy start, black smoke still on driveway marks.
Yes you are right my van rich fuel mixture too much, I smell it from exhaust. I booked my another local mechanical already for next week Tuesday, if he able to fix or not? He does service old cars with Carburettor .
Can you please ask your dad, which spare parts I need to replace for fuel rich mixture,
Do I have to buy new fuel regular pressure Or should I buy brand new Carburettor rebuilt from eBay seller must be from Australian. May cost $350.
or
Should I buy 4xFuel Injector Fits Toyota Hiace RZH103 RZH113 RCH12 RCH22 2RZ-E 2.4L 1995-2004 was listed Ebay, cost $85,? Should I buy from Repco
should I buy new air Filter and new petrol filter? My van only original 110k km low.
Thank you for reply me ASAP
Today I am taking van to another mechanical to check fuel rich mixture.
I need 4y engine
They’re pretty good motors. They still make them today and put em in forklifts
Perfect, just wish you also cleaned up and serviced the transmission. They may say 0 maintenance from factory assembly but like the differential gear oil, they need their oil to be replaced every 15-20 years. Along with cleaning the shrapnel magnets. The magnets could also be replaced or recharged.
Hey mate, yeah after cleaning the engine up and slapping the two part together it did look a bit unloved. But rest assured i’ve serviced the tranny every 12 months just to make sure it’s turning over right, being an auto I like to make sure the oil is always fresh and pan valves are clean. Yet to find any metal in it so he’s turning over beautifully. Thanks for watching, cheers 🍻
@@theseroadsweroam Awesome, cheers mate!
A great wall wingle 5 has this engine with fuel injection, dubbed 4Y-E. Same stock engine, with multi-point injection intake manifold at the same position. So larger parts source. I will be changing mine to a carburetor for easier fuel swapping and decoupling as much electrical from my combustion cycle.
Yeah right, well I guess they still make 4Y motors in china now for use in forklifts because of their ability to run LPG so makes sense GW is onto it. I love my carbys personally, grew up on dirt bikes so been around them more. Only thing I’d want to look into changing is the electric distributor ignition system that came out on the 3y engine of the time but that’s more money
I’m glad you share a passion on the simplicities of the old school motors
not me good jeans !!!!!!!!!!!!!!!!!!!!
I’ve quickly learned that you can’t carry only good clothes on the road. The farm clothes get more use than you’d think 😂
Why not put V6 Commodore Engine much stronger, company doing at Moree NSW, Van need new metal bracket, new petrol pump fit back tank, new wirings kits, Cost approx. $7000 Dollars Approx., plus delivery van to Moree and return van back to you, but Van need new BLUE SLIP, New different Motor, Registration Office have to Approve and Reweight Van as KG.
OR
Electric Motor, run by Batteries Electric Vehicle, No service needs for 50k km no petrol or no oil needs save a lot. Van old 19th century machinal has to pull all out and install 21st century Electric Motor in.
I have seen these vans with ecotech commodore motors in them, however our van was built to have this motor in it and the process of an engine swap was not a viable option for us as we wanted to be back on the road ASAP. Also for us, the cost of an engine swap, petrol or electric would cost more than what the vehicle is worth.
Get out of here with your electric car BS