Loving that yaesu Neil thats a nice bit of kit for sure and tempting me to buy one now.. Obviously I’d not want to stick a hot iron inside it though I’d leave that to you as you seem more competent than me at that sort of thing.. Fab channel mate hope to maybe catch up with you sometime soon and purchase another moonraker off you for my collection..
Thanks Phil, Yeah It seems to be a very popular radio especially while Yaesu are offering seemingly endless cash back offers. I am tempted to buy one myself in the near future to have a proper play and run it against the DX10.
Thanks for sharing , i was going to get an 891 but as i am so used to having a waterfall on my 7300 i think this radio would be a better option .I intend using it mobile decisions decisions.
My next radio will probably be a FT891 for Mobile and Portable, obviously the FT710 is a great rig and a totally nicer radio to operate but it is just a bit big for mobile and definitely no good for karting off the beaten track on your back. I suppose it comes down to your needs.
I’d like to request a video showing us where the 150mA SMT fuse in the DVI-D external monitor circuit is located. I have yet to find a schematic or board diagram on-line. Those with SMT equipment and skills could replace the fuse if necessary instead of sending it to Yaesu. Thanks for this video. Edit: I found the Technical Supplement for the FT-710. The “Fuse” that I imagine to be the monitor issue is located on the same side of the board that you show in your video (very accessible). From the Technical Supplement; “D5V” enters the MAIN-2 schematic sheet, passes through a zero ohm resistor R1860 to become “DVI5V”. DVI5V passes through ferrite bead FB1805 then PolyFuse Q1802, then Diode D1800 to pin 14 of the DVI Connector J1803. I am guessing the PolyFuse is the issue, but I understood that PolyFuses “Recover” from fault, when the fault is removed…….
@@PacTel54321 I would but I don’t have a FT710 here at the moment, this radio was apparently intentionally fitted with a resettable poly fuse probably due to all the issues with the FTdx10 and 101. I suppose it still could still be at fault or could even be a surge issue, as you probably know poly fuses aren’t the best with big surges so it could be another failure. Probably easier to check everything around that circuit. As soon as i get another in here i will take a short video.
@@gtretroworld I agree. I see that the DX10 originally had an 0402 "Zero Ohm" Resistor that was updated to an 0402 fuse; the latest schematic and parts list say 0.63A. The latest 710 shows a poly switch & also has a TVS network on the SCL & SDA lines.
Thanks and it was good to meet you today. I will hopefully pop a few videos up in the future that cover other Retro goodies as like i said it has gone a little off track.
Done this mod for a friend on his 710 done the reset still won't tx out of band unless its a japan version ??? How can I tell is there a difference with the serial sticker ??
Yes it looks easy, so I did it with my FT-710 Field. But no success. He does not transmit on the 11 meter band. Only on the amateur bands. What could it be ?????🙏🙏
@@flyingdutchman1805 I presume it is a EU or US radio as they seems to be a good few Japanese FT710’s circulating. Anyway make sure the firmware is up to date, recheck your soldering for continuity and try resetting the radio again. Hope this helps.
@@gtretroworld Het is een EU set die ik van de week heb gekocht. Ik gaat er van uit dat de firmware die ik nu in de radio heb, oud is. Ik zal deze van de week gelijk even update. Mijn soldering is goed heb al gekeken met een camera.
Worth checking the firmware as it happened to someone else on here who had older firmware, why this was the case i don’t know but it was. Also try resetting the Radio again.
Great video, thanks! I have an FT991a that I bought from GigaParts with a MARS mod. The mod only addresses the HF portion of the radio and not the VHF/UHF. Do you know if it's possible to modify that as well? Thanks again!
Thanks, Yes the FT991 is MARS/HF only. You can use service mode to enable VHF/UHF but it isn’t a permanent or ideal workaround. I will dig a little deeper and if i find anything i will let you know,
@@gtretroworld tap in to the main output black and red inside the radio lead comes out side vents jack in line connect the speaker the main one cuts out the only thing this radio lacks a external output the one in the back has you know is for aess
I used a solder rework station and very fine solder. I only used the hot air aspect of the solder rework station. It is more forgiving than a big sloppy soldering iron.
@@indridcold8433 I think most that are watching this are not very confident with working on expensive equipment. I normally don’t recommend anyone using hot air without experience or a quality tool as i have seen a lot of damage to surrounding components.
Great video. Tried this on my EU /UK radio but I'm still not able to TX on 27mhz? Updated firmware to latest version before the mod, bridged P51, did the Power/DSP/Fine reset but radio just behaves as before. I noticed that in the video the machine power cycles twice when you do the hard reset, mine only ever powers up once for the reset. Any ideas?
@@gtretroworld Thanks for the info. I must have been having a senior moment, I tried holding the DSP/FINE before the power and then keeping them held down a bit longer. That did the trick! All working as the video now. Cheers!
You have to open it up to add options like filters etc and the modification details are sent to engineers anyway and unless you’re not confident there is always an element of risk involved but to ruin the radio it would be rare. Thanks for your comment.
It maybe worth going back and checking your solder bridge as this has never failed with the few i have done. You can also reset the radio in the menu if it is easier with All Reset, hope this helps.
@@Industrialsoundfanatic I am not really sure as this and the others were checked and updated if needed before hand. I will say it is always worthwhile keeping up with the latest firmware updates.
I cannot see why Yaesu etc should not be allowed to offer 27MHz TX on their radios within the country's CB Radio Rules. In Australia, 4 Watts AM and 12 Watts SSB PEP. If the FT 710 could do that without this mod, I would be happy. I have an AX144 with no mods or extra power and I can talk across Australia on SSB easily at the moment.
@@stewheelie7874 I guess they could but i doubt anyone would pay Yaesu money for a 27mhz only radio. A lot are using these for 11m but most probably not within their countries rules. Yaesu don’t seem to care, same as the retailers who offer the modifications. I do see your point though.
Japanese radio regulations are odd. For example legal CB radios do not permit the use of a detachable antenna. So we can’t connect our piddly 0.5W to a roof top antenna or do field ops with an EFHW thrown up a tree for example. Because of this an HF rig operated by a legal and licensed Ham cannot be used for CB even if it could TX on 11m because it doesn’t have a permanently attached antenna. You can’t throw the radio up a tree and use a long external speaker mic either 😅 Surprisingly (heavy sarcasm) legal CB rigs cost as much as a decent ham rig over here. Go figure I think sums it up.
@@Tokyo1991.JL1AJE 0.5w for CB isn’t going to get you far especially if you can’t use a external antenna. As for using a HF Radio for CB it is probably a grey area in most western countries. Out of interest is CB Radio popular over there?
As far as I’m aware the FT710 won’t transmit 4Khz wide but i will look into this. I know for certain the FTDX10 has is it as I have one and it selectable in the TTBF settings. If i find anything i will check back. Thanks
@@gtretroworld I know for sure that 4k audio is activated on the American versions. Can you confirm for me if TBTF is activated after this change? If not, do you know a way to convert the version I use?
I would honestly say most opt for the MARS mod just for 11m and WARC especially on the older radios. I think MARS modified is just a term that everyone relates to wideband TX.
Maybe the manufacturers should get a clue and just open up all the bands once and for all ! Then if someone didn’t want a sh*ton of radios they could have a one and done . Or a two and done base and a mobile / portable rig . I’m sick of all the old FUDS with there holier than thou attitude nobody gives two sh*t’s about your self aggrandizing opinions.
Yet another mod where a blob of solder is used…. There is supposed to be a zero ohm surface mount resistor at 1/10 watt installed to make the connection.
There is absolutely no difference between this and a Zero ohm resistor, maybe the resistor would look prettier but that’s it. Even the Yaesu paperwork quotes use a solder short and probably every tech and shop is doing the same. Thanks for visiting the channel.
@@gtretroworld I beg to differ, The whole point of the pads is to employ a break in the circuit as protection with a 0 ohm resistor at a very low current rating to pop or break when a back feed or over current is applied and to protect the downstream components. If it were as easy as a blob of solder it would have a jumper point so it can be jumped. I guess we agree to disagree. although my 2 electronics degrees will steer me in the right direction.
@@KH07734 You will find most of the time the only reason 0 ohm resistors are used is it is loads easier for a machine to fit them over a link. The chance of even a low current resistor popping across this area and acting as protection would probably never work in my opinion and allow as much current through it anyway, well maybe not as much but you see my point. Anyway I always welcome any comments but maybe you should contact Yaesu as like i say this is exactly to there specific instructions and has been for decades across multiple radios. Thanks again.
There is no need to solder at all, simply use a small jewlers screw driver or someting simillar and with the help of a friend you simply hold the screw driver firmly over the two pads while your friend conducts a reset. The mod stays in place with power off or disconected. Only a factory reset or firmware update puts it back to factory in which case you do as above again...... easy and looks like it was never moded after a reset.
MARS mod? WHY ? How many hams are on military MARS? Really......This is one mod that is outdated and not needed. Every time I look at a used radio that interests me, I check to see if it had the MARS mode. If it did, I move on. I personally would never purchase a radio that someone dug into and made a MARS mod.
You will find a huge amount of Hams choose to wide band their radios. I can imagine 99% aren’t military at all. Obviously for freebanders which is probably the main reason it is definitely not outdated and probably what keeps these companies sales going. Tbh I rarely purchase a radio that has been modified unless i know where it’s been.
Expansion done!
The FT works perfectly on all possible frequencies, as well as its ATU.
Thank you.
Great! Excellent thanks for letting me know. 👍
That seems a lot easier to do than the Ft-891 or IC-705. Thanks for the video!
Thanks, I have yet to have fiddle with a FT891 and IC705 but both are radios i fancy trying one day.
Fantastic work Neil, great video 👍
Thanks Ben, Hopefully it will be of use to someone over the next few years.
Loving that yaesu Neil thats a nice bit of kit for sure and tempting me to buy one now..
Obviously I’d not want to stick a hot iron inside it though I’d leave that to you as you seem more competent than me at that sort of thing..
Fab channel mate hope to maybe catch up with you sometime soon and purchase another moonraker off you for my collection..
Thanks Phil, Yeah It seems to be a very popular radio especially while Yaesu are offering seemingly endless cash back offers. I am tempted to buy one myself in the near future to have a proper play and run it against the DX10.
Thanks for sharing , i was going to get an 891 but as i am so used to having a waterfall on my 7300 i think this radio would be a better option .I intend using it mobile decisions decisions.
My next radio will probably be a FT891 for Mobile and Portable, obviously the FT710 is a great rig and a totally nicer radio to operate but it is just a bit big for mobile and definitely no good for karting off the beaten track on your back. I suppose it comes down to your needs.
I’d like to request a video showing us where the 150mA SMT fuse in the DVI-D external monitor circuit is located. I have yet to find a schematic or board diagram on-line. Those with SMT equipment and skills could replace the fuse if necessary instead of sending it to Yaesu. Thanks for this video. Edit: I found the Technical Supplement for the FT-710. The “Fuse” that I imagine to be the monitor issue is located on the same side of the board that you show in your video (very accessible). From the Technical Supplement; “D5V” enters the MAIN-2 schematic sheet, passes through a zero ohm resistor R1860 to become “DVI5V”. DVI5V passes through ferrite bead FB1805 then PolyFuse Q1802, then Diode D1800 to pin 14 of the DVI Connector J1803. I am guessing the PolyFuse is the issue, but I understood that PolyFuses “Recover” from fault, when the fault is removed…….
@@PacTel54321 I would but I don’t have a FT710 here at the moment, this radio was apparently intentionally fitted with a resettable poly fuse probably due to all the issues with the FTdx10 and 101. I suppose it still could still be at fault or could even be a surge issue, as you probably know poly fuses aren’t the best with big surges so it could be another failure. Probably easier to check everything around that circuit.
As soon as i get another in here i will take a short video.
@@gtretroworld I agree. I see that the DX10 originally had an 0402 "Zero Ohm" Resistor that was updated to an 0402 fuse; the latest schematic and parts list say 0.63A. The latest 710 shows a poly switch & also has a TVS network on the SCL & SDA lines.
@@PacTel54321 Good information that i was unaware had been changed, i will have to check this out. Thanks
Nice mod. I will do the exact thing to my 710. Thanks. KC3VQZ Maryland.
No problem, thanks for taking the time to watch and comment. 73 M3VWN
GREAT GREAT VIDEO!!! THANKS from N4TUX Boyd Travis Kingsport TN. USA
No problem at all, thanks for visiting the channel, M3VWN
fab,dont forget cb fm bandwidth\dev narrow use N-FM👍
Thanks for the video Neil 🙂
Thanks Dave, hope you’re well.
Hello mate nice to watch your videos spoke to you in m&s today I was on till
Thanks and it was good to meet you today. I will hopefully pop a few videos up in the future that cover other Retro goodies as like i said it has gone a little off track.
Done this mod for a friend on his 710 done the reset still won't tx out of band unless its a japan version ??? How can I tell is there a difference with the serial sticker ??
The Destination or DST will be labelled on the Box, if it is destined for Japan it will normally show DST JPN. Hope this helps.
Yes it looks easy, so I did it with my FT-710 Field. But no success. He does not transmit on the 11 meter band. Only on the amateur bands. What could it be ?????🙏🙏
@@flyingdutchman1805 I presume it is a EU or US radio as they seems to be a good few Japanese FT710’s circulating. Anyway make sure the firmware is up to date, recheck your soldering for continuity and try resetting the radio again. Hope this helps.
@@gtretroworld Het is een EU set die ik van de week heb gekocht. Ik gaat er van uit dat de firmware die ik nu in de radio heb, oud is. Ik zal deze van de week gelijk even update. Mijn soldering is goed heb al gekeken met een camera.
Worth checking the firmware as it happened to someone else on here who had older firmware, why this was the case i don’t know but it was. Also try resetting the Radio again.
Great video, thanks! I have an FT991a that I bought from GigaParts with a MARS mod. The mod only addresses the HF portion of the radio and not the VHF/UHF. Do you know if it's possible to modify that as well? Thanks again!
Thanks, Yes the FT991 is MARS/HF only. You can use service mode to enable VHF/UHF but it isn’t a permanent or ideal workaround. I will dig a little deeper and if i find anything i will let you know,
crazy no one commented on that awesome BTTF tattoo!
Thanks, there’s more further up my arm including the Icon Ghostbusters logo. 😁
I have done it several times for people that pay me to do it. My question is, what do the other solder pads do?
Good question, I presume those will be for other regions, Japan etc. I will send Yaesu a mail and ask the question and report back.
@@gtretroworld Thank you. Your efforts are well appreciated.
@@indridcold8433 Thanks 👍
done the main speaker mod works great now i can but a external speaker to the main output the aes does not work but the audio is great
Out of curiosity did you replace the speaker and drill the cabinet?
@@gtretroworld tap in to the main output black and red inside the radio lead comes out side vents jack in line connect the speaker the main one cuts out the only thing this radio lacks a external output the one in the back has you know is for aess
Does the desk mic fit the g90 please
I am not 100% but i think the pin out is the same as Yeasu and if it isn’t i suppose it would be simple enough to wire up.
wish they used physical jumpers, my hands aren’t steady enough to do that bit of soldering
Honestly if you take your time with a small iron it will be over and done in seconds, if you were local i would’ve gladly done it for you.
I used a solder rework station and very fine solder. I only used the hot air aspect of the solder rework station. It is more forgiving than a big sloppy soldering iron.
@@indridcold8433 I think most that are watching this are not very confident with working on expensive equipment. I normally don’t recommend anyone using hot air without experience or a quality tool as i have seen a lot of damage to surrounding components.
Great video. Tried this on my EU /UK radio but I'm still not able to TX on 27mhz? Updated firmware to latest version before the mod, bridged P51, did the Power/DSP/Fine reset but radio just behaves as before. I noticed that in the video the machine power cycles twice when you do the hard reset, mine only ever powers up once for the reset. Any ideas?
Thanks…I have done a few of these and have never had an issue. Make sure you hold both DSP/FINE down then power it up and not all at once.
@@gtretroworld Thanks for the info. I must have been having a senior moment, I tried holding the DSP/FINE before the power and then keeping them held down a bit longer. That did the trick! All working as the video now. Cheers!
@@andysupermachine Excellent, don’t worry we all have those senior moments, as long as you get there in the end is all that matters.
Did it tx on 70 mhz
@@michaelmilenkoclewes572 Yes just fine.
Easy and clear explanation.
Well done, and Thank you!
Giovanni I0KQB
Thanks, Glad it was helpful!
I have a question:
aftet the modification, does the autotuner work on all the frequencies, included rhe new ones?
@@giovafra61 Yes it works on all frequencies perfectly well to the usual Yaesu nominal 3:1 SWR range.
@@gtretroworld Very well.
So, I'll do that modification.
Thank you very much!
Giovanni I0KQB
@@giovafra61 No Problem, Just take your time. 73 M3VWN
l'autotuner fonctionne après la modification test ok
Did it tx on 70 mhz after
Yes no problem at all with the EU version.
The manual says that if you open or mod you will ruin the radio
You have to open it up to add options like filters etc and the modification details are sent to engineers anyway and unless you’re not confident there is always an element of risk involved but to ruin the radio it would be rare. Thanks for your comment.
The Japanese one cannot be done
Apparently so but i have yet to try one.
That opens up cb radio ?
@@KE8ODY-WV-Ares-Ham-Dad-3O4 Yes, basically all HF.
@@gtretroworld man that’s scary I used my ftdx10 but my 710 is brand new back up I wanna do it lol
@@KE8ODY-WV-Ares-Ham-Dad-3O4 All i can say as long as you take your time I’m sure you will be fine or alternatively pop it to a local tech.
@@gtretroworld I just did the mod on my Yaesu ft2900r no issues but
Tried this mod, but holding down the buttons on start up won't activate the mod for me.
It maybe worth going back and checking your solder bridge as this has never failed with the few i have done. You can also reset the radio in the menu if it is easier with All Reset, hope this helps.
@@gtretroworld I don't have the latest firmware, maybe this could be the problem.
@@Industrialsoundfanatic I am not really sure as this and the others were checked and updated if needed before hand. I will say it is always worthwhile keeping up with the latest firmware updates.
@@gtretroworld Thanks buddy, great video and good advice.
@@Industrialsoundfanatic No problem and thanks for visiting the channel.
I cannot see why Yaesu etc should not be allowed to offer 27MHz TX on their radios within the country's CB Radio Rules. In Australia, 4 Watts AM and 12 Watts SSB PEP. If the FT 710 could do that without this mod, I would be happy. I have an AX144 with no mods or extra power and I can talk across Australia on SSB easily at the moment.
@@stewheelie7874 I guess they could but i doubt anyone would pay Yaesu money for a 27mhz only radio. A lot are using these for 11m but most probably not within their countries rules. Yaesu don’t seem to care, same as the retailers who offer the modifications. I do see your point though.
Japanese radio regulations are odd.
For example legal CB radios do not permit the use of a detachable antenna. So we can’t connect our piddly 0.5W to a roof top antenna or do field ops with an EFHW thrown up a tree for example. Because of this an HF rig operated by a legal and licensed Ham cannot be used for CB even if it could TX on 11m because it doesn’t have a permanently attached antenna.
You can’t throw the radio up a tree and use a long external speaker mic either 😅
Surprisingly (heavy sarcasm) legal CB rigs cost as much as a decent ham rig over here.
Go figure I think sums it up.
@@Tokyo1991.JL1AJE 0.5w for CB isn’t going to get you far especially if you can’t use a external antenna. As for using a HF Radio for CB it is probably a grey area in most western countries.
Out of interest is CB Radio popular over there?
conductive paint the best way
I personally wouldn’t use that method but i guess if it makes a contact it will do the job.
will it do the 4 Khz transmit mod also in the menu?
As far as I’m aware the FT710 won’t transmit 4Khz wide but i will look into this. I know for certain the FTDX10 has is it as I have one and it selectable in the TTBF settings. If i find anything i will check back. Thanks
@@gtretroworld ok thanks,Simon the wizard took it off the net for some reason.
@@gtretroworld I know for sure that 4k audio is activated on the American versions. Can you confirm for me if TBTF is activated after this change? If not, do you know a way to convert the version I use?
Why mod for MARS if you are not a MARS member
I would honestly say most opt for the MARS mod just for 11m and WARC especially on the older radios. I think MARS modified is just a term that everyone relates to wideband TX.
@@gtretroworld I think it's for bragging.... I wouldn't buy a radio that was modified.
Some people like to live life on the edge... Crazy times eh
Maybe the manufacturers should get a clue and just open up all the bands once and for all ! Then if someone didn’t want a sh*ton of radios they could have a one and done . Or a two and done base and a mobile / portable rig . I’m sick of all the old FUDS with there holier than thou attitude nobody gives two sh*t’s about your self aggrandizing opinions.
Yet another mod where a blob of solder is used…. There is supposed to be a zero ohm surface mount resistor at 1/10 watt installed to make the connection.
There is absolutely no difference between this and a Zero ohm resistor, maybe the resistor would look prettier but that’s it. Even the Yaesu paperwork quotes use a solder short and probably every tech and shop is doing the same.
Thanks for visiting the channel.
@@gtretroworld I beg to differ, The whole point of the pads is to employ a break in the circuit as protection with a 0 ohm resistor at a very low current rating to pop or break when a back feed or over current is applied and to protect the downstream components. If it were as easy as a blob of solder it would have a jumper point so it can be jumped. I guess we agree to disagree. although my 2 electronics degrees will steer me in the right direction.
@@KH07734 You will find most of the time the only reason 0 ohm resistors are used is it is loads easier for a machine to fit them over a link. The chance of even a low current resistor popping across this area and acting as protection would probably never work in my opinion and allow as much current through it anyway, well maybe not as much but you see my point. Anyway I always welcome any comments but maybe you should contact Yaesu as like i say this is exactly to there specific instructions and has been for decades across multiple radios. Thanks again.
There is no need to solder at all, simply use a small jewlers screw driver or someting simillar and with the help of a friend you simply hold the screw driver firmly over the two pads while your friend conducts a reset. The mod stays in place with power off or disconected. Only a factory reset or firmware update puts it back to factory in which case you do as above again...... easy and looks like it was never moded after a reset.
@@gtretroworld you employ your training and I will go with my 30 years experience in the industry . Enjoy.
MARS mod? WHY ?
How many hams are on military MARS? Really......This is one mod that is outdated and not needed. Every time I look at a used radio that interests me, I check to see if it had the MARS mode. If it did, I move on. I personally would never purchase a radio that someone dug into
and made a MARS mod.
You will find a huge amount of Hams choose to wide band their radios.
I can imagine 99% aren’t military at all.
Obviously for freebanders which is probably the main reason it is definitely not outdated and probably what keeps these companies sales going.
Tbh I rarely purchase a radio that has been modified unless i know where it’s been.
Nice clean job 👍👍
Thanks Andy 👍