Thanks man! You saved me over $600. Camera went bad on 2016 F-150. Dealership wanted over $1000 to fix. Bought the camera online for half of Ford's price and then installed it in 10 minutes using your video. Bought the USB ODB II for $20 and calibrated the new camera using your instructions. The process of downloading the software and getting a license was a little laborious, but when it came time to connect to the truck and calibrate, again it took 10 minutes. So, the dealer wanted $1000 for 20 minutes of work...ridiculous!
Thanks for the video. Am in the process of troubleshooting my backup camera and no one else has a video of how to disassemble everything, so this video helps a lot
Great video worked! Few tips! USB ODB is correct but my switch was wrong direction from instructions. When loading if ATC comes with an error, then the switch is in wrong direction for HS MS flip switch it’s in wrong spot. Also when it starting up and it wants to load the previous saved F150 say no. Your loading same file which is missing most modules like FCDIM. Finally when you write all it will say successful under log, but I had to press stop button before disconnecting. You need forscan extended to do changes. Btw 5 ford dealership in my area said it’s not possible. I was just replacing damaged OEM screen with stock camera. They said it was plug and play. Well ford has about 40 screens for same gen F150. Go bite a big one ford!
Thank you for putting this video up and also the link to wire from tailgate to hood. I saved hundreds of dollars and did it myself. Amateur tip, when wiring from back of tailgate to the front of truck remove the spare tire. I could actually sit under the truck while pinning the five new wires onto the connector. I work slow so this was nice.
GREAT INFORMATION. I just installed an electric braking system on my F 150 but got very little help from the parts dept at the dealer. Back up camera is next. Your video will make it much easier and massively shorten the time frame. Dp youknow what the wiring harness behind the coin holder on the dash is for. Thanks, again.
Just wanted to say thank you to Make Stuff Nation for the camera install, the author of the Ultimate XL OEM Backup Camera Guide for the, true to it's name, excellent guide to getting the wires installed into the existing harness. Thanks to the Forscan folks and all the help there as well. I'm very grateful for all the folks sharing their experience with newby's like me.. John..
I really appreciate the very detailed video. I purchased the aftermarket camera, harness, and latch assembly for my Ford 2017 F150. I installed the hardware following your step-by-step directions. I used Forscan to change the code (7A5-01-01) from 2029 to 2229. Selected "Write All" in Forscan. Turned the truck off and on. I thought I was all set. Nope! When I go into reverse, there is a pause on my 4" screen, then it says "REAR VIEW CAMERA NOT AVAILABLE". The truck senses that there is a camera present as it shows up in the Menu. I have retraced my steps in Forscan and checked all the harness connections. I am unsure how to move forward! I would appreciate any help or feedback to solve my issue! Thank you in advance!!!
Hi Michael, I am having the same problem and I'm pretty sure it's because the rear wiring connector only has 2 wires and I will need to run wires from the rear to the front as described in the PDF. I do not feel comfortable doing this myself so I am looking for more resources or a good place nearby.
I tried reading your "The Ultimate XL Backup Camera Install Guide," which of course, is NOT informative, but is really Ultimate Unintelligible Gibberish. When I read a manual, such as yours, I cannot help but thinking, "Was it too much crack, or not enough?" Half-explained procedures, undefined parts, wires, slots, with a few nice pictures thrown in that tell little. But it's "Ultimate" so it must be good, right! I bought the stupid camera, and I need to figure out how to run wires to the front. I'm drowning here, and you're throwing me an anchor. Great job!
Hi ,I have 2016 f150 I try put back camera and used with screen 12.1 linkswell I buy same camera and wire you used on the video but the truck don't detect so can I used the forscan to detect the camera,
Hello Make Stuff Nation, I watched your video and it is great on how to install and program the backup camera. I own a 2015 F-150 XLT Super Crew Truck and have watched several videos where a factory camera was installed in the tailgate, wires were run up the drivers side of the truck into the cab, uninstalled the screen, installed a special RCA plug and reassemble everything. Can you tell me where to look on my truck so I can decide which option I will need to perform to install a backup camera??? I look forward hearing from you soon. Thanks
Awesome video, but before you go and buy parts make sure your truck is wired for camera. If the wire harness mentioned in minute 5:50 only has two wires coming from the main wire harness, your truck is NOT wired. Don't even bother! I learned this the hard way.
Great Video!!! i notice this video was uploaded 4 years ago. the prices on the parts are triple!!! is it because of demand? or did you have a discount at that page?
Make stuff nation I just purchase all the necessary parts including the wires and male/ female connector parts. Before I get started can you tell me if the male parts go under the truck or in the front and I assume the female connectors go opposite of the male connectors. Couldn’t really tell by the pictures and don’t see where it tells you which ones. Thanks
How has it held up? I'm looking into doing it to a new to me 2017 F150 XLT. But, I'm weighing my options due to the increased cost for the camera. Although if you say that it's held up, I would feel better about purchasing a 300.00 camera.
It is still working well for me and I haven't had any issues since install. No idea if the parts/camera available today are the same quality as the ones I used.
Is there a schematic or something to have wires in correct slots on the end that connects to tailgate harness from front of truck? Wasn’t covered in the tutorial diagram or I missed something. Thanks
sorry about that, here is the pinout: Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck) Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck) Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck) Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck) Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
My 2017 F150 has sync 3 but no backup camera, I was able to find a used oem handle with camera and harness, but after a closer look at my grey plug it only has 2 wires. Meaning my truck is not prewired for the camera.
I would check the PDF guide that is linked in the description. Have you confirmed that you have all the wires run from the front harness to the back harness?
Great video, i had a completely unrelated question though, what are the dimensions of your garage? Ive been looking to build a garage and yours looks like the perfect size for the amount of space I have. Thanks!
hey make stuff nation....thanks for the video. helped a lot....I have a question though....i did all the process since I change my 4in screen and all works. the only thing missing is the zoom function that doesnt work when it used to. I checked through the spreadsheets but cant find anything to fix this. Any idea for me ? thanks again
Does this work for the larger touch screens? My husband has a 2017 Ford F150 XL also, and I really want to get him the set you got, but I want to make sure I buy it right the first time. Is this the best set, or is there an all in one?
I'm having trouble trying to connect. I purchased the recommended OBD2 USB cable and I have it hooked up to a Windows 10 laptop. I pull up the forscan, plug it up, turn my key to on, and hit connect on forscan. Nothing this is on a 2017 F-150. I changed the APIM for nav features. I don't know if that would have anything to do with it or not, but it just will not connect.
I have a F150 XL, you said it is already wired for the camera, is that true for all 2017 XL's? Isn't there a certain amount of wires needed in the molex connector to tell if it is prewired or not?
Hello there, I perform everything as your video showed. My year model is a 2015. When I open FORScan I don't have FCDIM module, I do however have a BCM module. Any ideas where else I can find the rear camera setting? The spreadsheet provided has way more module than my FORScan shows. I am pretty sure that it the operator not the equipment issue that I am experiencing. Thanks in advance for any assistance. Greatly appreciated Thanks
I'm the author of the FORScan tutorial & spreadsheets referenced above. What adapter are you using? If you're using the correct adapter that can access the MS-CAN modules as well as the HS-CAN modules and it has a toggle switch on it then try the following: 1. go into FORScan settings, connection tab and change "MS-CAN Support" to "HS/MS Switch" 2. connect to your truck again in FORScan but click no when it brings up your VIN profile 3. it should then find a few modules and then prompt you to flip the toggle switch on your adapter and find the rest of the modules 4. if it finds all modules then you can save this new VIN profile and use it on all subsequent connection attempts.
Hi John, I'm using the Bluetooth version of the OBD connector on my 2017 F-150 XL. I installed the camera and had to install the wires in the harness... Great video and XL instructions! I'm also not seeing the FCDIM. Forscan is picking up both HS and MS CAN modules, just not this one. Is it possible the FCDIM is not installed on this truck? Thanks, John Skelnik, skelnik@us.net
I answered my own question from the F1-50 forum. Linked here: www.f150forum.com/f118/ultimate-xl-oem-backup-camera-install-guide-398123/index2/ Quoted here: Quote: Originally Posted by 10iron View Post I intend to add an aftermarket camera to my 2017 F-150 XLT. I have seen it suggested that the modification with Forscan should occur at 726-39-02 7A5-01-01 7D0-01-01 All of these modication addresses supposedly worked. Any explanation for which point is correct or best would be appreciated. Thanks for taking time to help. JW 726-39-02 (all configurations) The value in the sixth place tells the BCM that a camera exists (0 for no, 1 for yes). This gets your dynamic lines and zoom working. 7A5-01-01 (4.2" screen only) The value in the second place tells the FCDIM that a camera exists (0 for no, 2 for yes). 7D0-01-01 (8" screen only) The value in the second place tells the APIM that a camera exists (0 for no, 2 for yes, A for yes w/obstacle detection) To summarize: If you have the 8" screen, you need to change values in 726-39-02 and 7D0-01-01. If you have the 4.2" screen, you need to change values in 726-39-02 and 7A5-01-01.
I have a F250 for work but with a tool box style bed. I added the rearview camera with a separate screen but I want to interface it to the factory screen. I think I saw a 9 pin connector on the frame in the back so I wonder if the truck is pre wired for it. I already have forscan. I just need to figure out what wires are the composite video signal.
Make sure you are using an good MS/CAN compatible OBD II reader. I recommend this one: amzn.to/34qtT1N. If you already are, try clearing the DTCs that are present.
This is a great help. I should not have to run any cabling if the truck comes equipped with a lock actuator in the tailgate correct? Also, were you able to get the backup lines to appear on the screen?
Yes, I was able to get them working, use these steps (steps 3 & 4 turn on the lines specifically): 1: Connect ForScan, follow the prompts when connecting. 2: Under the FCDIM module, on the 7A5-01-01 line/field, change the 2nd digit from a "0" to a "2". Save/write the change (follow the prompts). (this activates the camera) 3: Under the BCM module, on the 726-39-02 line/field, change the 6th digit to a "1". Save/write the change (follow the prompts). 4: Click the wrench icon and run "LIN New Module Calibration". This makes the truck recognize the changes and calibrate the modules (follow the prompts). 5: Disconnect ForScan
@@MakeStuffNation Great Video! I installed everything just like shown in your video on my 2016 XLT which has the lock actuator. I took it to get programmed with Ford and they could not program it. I have not looked to see how many wires are running into it. Would the FORSCAN be the better solution?
Were you able to figure out how to get the guide/center lines to show up on your display? You mentioned there might be an additional setting you need to change...
The physical camera install would take about a half an hour, and anyone can do that! What does it cost to just have the dealer boot the cam? $100 bucks next time I have the oil changed? Perfect OEM codes, no wasted time, no muss, no fuss, no nebulous codes and sketchy software and sketchier OBDII cables. Done and DONE!
It seems as if my xlt only has the two wires. Is it possible to just purchase a replacement that is prewired that runs from the engine bay to the cab? Or does this have to be done manually? If so, what would that part be called so I could order it? Any help would be greatly appreciated!!!
Unfortunately if you only have the two wires, you will need to run the additional wires yourself. Because it is part of the main wire harness of the truck I don't think there's a part available to order. The PDF guide that I have listed in the description walks you through adding the additional wires yourself.
good intellectual video, thx for it, to do this, it is not cheap other than your own free labor, the part cost at amazon is $300 and plus the computer software cost$190, hence, you can tell it is $500 already, no wonder the ford dealer at san jose northern california try to charge $1000 to install a back up camera.
I did everything, and as I went to plug the new connector into the existing connector I saw the connector only had two wires, for the lock/unlock. After reading the instructions on how to add the 5 new wires I'll need, it would be easier (although more expensive) to replace the factory harness from the tailgate to under hood. Does anyone know the part number for the complete harness? Thanks in advance.
Yes, it should work. You just have to confirm that the additional camera wires are run from the front wire harness to the back harness plug. The guide in the description shows how to identify these wires and how to install them if they're not already there.
Changed my 15 tailgate to a 18 tailgate like the F150 detent in the tailgate. Everything was a bolt in swap (linkage) except for the handle ... then found out it has a different camera. Got all that changed and backup camera works but lost my guide lines. Plugged in the old camera and guidelines came back and was square even though the camera was dangling. Like you trying to figure out how to bring the guidelines back on the new camera I found this on the Forscan site but do not know the sequence to cycle the key. If you figure it out I would appreciate it! Re: Code: B115E - Camera Module Post by Echerr » Thu Dec 19, 2019 9:29 pm I was able to fix my rear camera on my 2016 F250. My tailgate was stolen and after I replaced the rear camera with a new one the fixed and moving guide lines were missing. I was also unbale to zoom in. The DTC i had stored was B115E:55-0A. After i connected with OBDLink EX (usb to OBDII) I ran Forscan. Under the wrench icon I selected “Local Interconnect Network New Module Calibration” under BdyCM. After it ran I cycled the key to off and back to on as instructed. Both fixed and moving guide lines are now present and the zoom function is now working. Hope this helps.
@@MakeStuffNation not fixed yet trying to figure out how to bring the guidelines back on the new camera ... do not know how to do the the sequence to cycle the key ... do know the exact procedure to do this?
I'm getting the same thing on my 2016 XLT. I did not have the wires run from the back of the truck to the front, so I followed the instructions in the included link to run those. When I put the truck in reverse, I get Rear View Camera Not Available.
@@bouncebynum I'm looking to do the same install as you-somewhere either in this UA-cam listing or the F150 forum people talk about how they resolved your same issue. I have a 2018 camera/tailgate on my 2017 F150 XL and I've just been reading about it alot.
@@EdGrube No, but I haven't had much time to work on it. I need to double check that I've got good continuity over the wires that I had to add to the connectors and that they're going from the right pins to the right pins. After that: I've heard that sometimes the harness between the truck and the screen sometimes does not have the 3 video wires. I need to verify if that's the case in my truck.
I have 2016 F150 supercrew XLT. The factory harness is GL3T14B562KA. Will the harness you used be able to replace mine? And can I get dealer to flash software next time I get oil change?
The dealer can flash the software but they usually charge you extra. Not sure about the part numbers but they might be able to answer that question for you.
Great vid. I had to run the wiring per the PDF. Still getting "camera not available." I'm double-checking my pins now. Can you describe the location of pins 1-5 on the rear harness? (I did orient the wires exactly as shown in the PDF). My rear connector doesn't seem to be numbered. (The engine bay connectors are numbered). (I did orient the wires exactly as shown in the PDF). Edited to add: ordered a new camera and it works! Woot!
Pretty sure I figured that out--the PDF describes pin 1 as the upper right corner. So all my pins are correct. I have not been able to run LIN network new module calibration. Says I need to clear error codes. I have one error code B115E camera module bus signal. It will not clear. Haven’t found an answer as to what this is
@@chuckthompson3358 I bought a 2018 tailgate with camera-hopefully no issues hooking this up. I'm assuming your was the 4.2 non-touch screen. What did you download from Forscan?
Ok so I fucked up my tailgate and I was looking for replacements and I found an OEM with the back up Camera what type of harnesses will I have to buy to get it to work I have a 2017 XLT Crew Cab with the basics
I just finished this on my 2017 XLT. Everything went exactly as described in this video and the linked guide for running the wiring. One final question: Has anyone figured out how to get the red/yellow/green lines to appear on the screen? I get the image with the magnifying glass and horizontal bar at the bottom of the image, but no multi-color guide lines on the sides. Also, the magnifying glass doesn't seem to do anything.
I had the same issue at first. I figured it out and wrote instructions in the description of the video. They should be pretty clearly labeled and easy to follow. It's just another module you have to activate in ForScan.
Great how to video, thank you. I have all the parts on your list and going to be doing the install this weekend. I downloaded Forscan and somewhat familiar with it. What was the code originally and what did you change it to exactly just to be sure. Thanks again
Mike Carroll I did and it was it easy like in the video. I got it all to work but I had to make a harness going from the backup camera to the front of the truck and tap into the stock harness. Pain in the ass
Thank you for the reply! I ordered the parts last night. You weren't able to connect to the stock harness back near the spare tire? Where did you access the stock harness at the front of the truck? Just in case I have the same issue...
If your stock harness doesn't have the connector/pins at the back, you will run lines up to the 2 main wire harness connectors under the hood mounted to the top of the drivers side front wheel inside fender cover.
After you ran the wires from the back to the front engine compartment, did you need to do anything with wiring behind the actual radio? I ran the wires, changed settings and get a “rear view camera not available message “
Im tring to activate my friends backup camera. this activates the camera right? not just the "backup lines" "To activate the backup lines on the camera: 1. In Forscan, edit 726-39-02 in the BCM, place a 1 in the 6th digit, and apply the change. This setting tells the BCM that a rear camera exists. It is on Livnitup's spreadsheet as "Slave Exists RVC" 2. In Forscan, click the wrench icon and re-run LIN New Module Calibration."
Okay, that part is to turn on the backup lines if the camera is already activated. Here are steps to activate the camera and then turn on backup lines: 1: Connect ForScan, follow the prompts when connecting. 2: Under the FCDIM module, on the 7A5-01-01 line/field, change the 2nd digit from a "0" to a "2". Save/write the change (follow the prompts). (this activates the camera) 3: Under the BCM module, on the 726-39-02 line/field, change the 6th digit to a "1". Save/write the change (follow the prompts). 4: Click the wrench icon and run "LIN New Module Calibration". This makes the truck recognize the changes and calibrate the modules (follow the prompts). 5: Disconnect ForScan
Hello. I just got all my parts and install was a breeze due to your video. I have changed the modules and described but when I run LIN New Mod... it keeps aborting when I turn my ignition back on. Any advice?
Can someone show me exactly what the codes will look like when they are changed I dont understand when it says change the 0 to a 2. And when its says changed the 6th digit
I assume the wiring it the same on both models. You'll just have to check the harness at the connectors and see if they ran all the wires or if you'll need to add some.
I'm considering adding a camera to my 2017 XLT. I'm wondering if it is pre-wired like yours was. The existing connector to the tailgate that's by the hitch only has 2 wires coming in and out. I'm guessing that means my truck was not pre-wired, correct?
Gonzoagg09 that is correct, if it only has 2 wires you need to run the 5 camera wires from the engine bay back to the connector. See the ultimate backup camera guide file posted in the video description. It's a pretty easy process. Unfortunately I don't have video footage of that install.
I have a 2017 XL and also only have the two wires. what wiring harness would you use for that? Can I use the one you did ? I’m trying to find a wiring harness that’s already wired and I can just connect and run through to the back of the screen and I have the 8 inch sync 3 does the the forscan work for that ? Thank you for any help or advice you can offer
So, I installed this exactly like the instruction in the PDF. I ordered all the parts mentioned. Wired it up just like it said. loaded the FORScan stuff, and it works, but the image is update down. Any ideas? 1 - Brown - 33 2 - White - 7 3 - Blue - 11 4 - Green - 12 5 - Black - 13 2017 XLT 4.2" screen
EdGrube No, Not yet. I have come to the conclusion that I have it wired correctly, and it is either the wrong camera for this application, or the camera was assembled incorrectly. I wondered if I could just flip the assembly around, but it looks like the plastic assembly is welded together. I was trying to get the supplier to send me another one before I wreck this one. If the supplier won't send me another one, and I'm on my own, I'll try forcing it apart, or I will have to flip the whole assembly and silicone it in place.
So I bought everything from Tasca Auto Parts as the video suggested and the OBD II and download Forscan. Installed everything and when I changed the numbers as it stated to in the video and the notes I get an error stating backup camera not available. Also I get a code error when I do the LIN calibration. Can you please help me out with what I am doing wrong. I looked at a lot of forums and a lot of people are experiencing the same issue. I really don’t want to take it to FORD as they are going to charge $180.00 to flash the chip.
I am experiencing the same issue. If anyone solves please post. i bought a camera that i though was OEM but was a doorman, ordered OEM. Still same error. I will check for 9 pin vs 3 pin next. I also added the led bed lights that came with the harness for the camera. I threw time and almost 300 dollars at this and still no luck. disapointing.
I have installed the OEM camera and ran the 5 new wires as per the video and pdf; however after setting up FORScan I am getting a “rear view camera not available” error via my 4.2 inch Sync screen. Does anyone have any idea on what I may be missing here or have you ran into this issue and found a remedy? Any help would be greatly appreciated
I am having the exact same issue. I thought it might be that I didn't have wires running from the front to the back but when I called Ford, they assured me by running my VIN that my vehicle was setup for a camera. I still have not been able to get an answer to this issue. Does anyone have any advice?
Bryan Huntley check the harness that you connected the camera to that runs to the front of the truck. It will visibly have 3 cables( not wired) or 7 (wired)
try checking the wires you ran for this pinout: Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck) Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck) Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck) Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck) Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
Same issue. I don't understand how checking the wires helps? Are y'all saying I may need to change the pin configuration from how the harness is already set up? Everything is correctly plugged in as he shows on the video????
Chuck Thompson my originally was that My 17 f150 was not pre wired for the camera. After I followed the video instructions I had to also read the attached pdf and run wires from under the hood to the new harness that was installed via the video. As for my 2nd problem one of the wires (the ground for me) had broken and I had to re-run it. Everything was wired correctly; however I had to replace a wire and discovered this by checking to see which wires had power or not. I hope this helps ;)
Hi Make Stuff Nation, i have a dumb question. I understand that the color of the wires are irrelevant. I am building the wire harness for truck side, the tail end connector will use the slots from 1to5 and the front will be 7,11,12 and 13 on one connector and the on the slot 33. The question is the following: what is the relation of the pin numbers beetween the aft connector and the front connector?...1 goes to what pin on the front connector? 2 goes to what pin on the front connector etc. Do you have a wire diagram? I need to know the order. Please help.
Okay, I just checked my truck and confirmed the pin layout. Here it is: Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck) Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck) Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck) Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck) Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
Hello Make stuff Nation, i am on last step of this project. I have built and run the new harness. All parts installed. Reprogram the Codes. I am getting the Rear veiw camera not available message. Anything else that i need to do? Or maybe a video that can help? Please help me.
Anybody able to get this to work on 2016 XLT model? I did all the wirings to the instructions and installed everything. Took to local Fortd dealer to get it activated ($49.99 activation), but they couldn't get it to activate. Do I have to get FORScan and do it on my own? Great video and instruction by the way.
So finally got time to get the backup carema to work on my 2016 F150. Tested the resistance on Pin 6 and Pin 12 on the back of the display unit( got 73 ohms). A plus was that the harness to the display was pre-wire for these two pins (I took the connector that plugs into the display apart). Downloaded Forscan and followed the instructions on here. Was able to get the guide lines and centered black line to come on also. Thanks to all those who pioneered this mod.
Hopefully someone can help me. So my truck came with the tail gate camera and was already wired. Nothing would appear when I put it in reverse. Got Forscan and did the numbers they said use. Now I get a blue screen in reverse. Iv swapped camera and still the same. Any help here?
Just install the camera on 2017 f150 xlt. Can’t find step 4 “LIN new module calibration”. ( is the forscan version different from yours?) The screen has no image, only show “rear view camera not available”. Do you think is cause by the hardware or software.
Can anyone tell me where this guy got the pigtail and tailgate handle from? I can find some handles, but no wiring for my back up camera like the one he has.
Great video for the do it yourselfers! The only problem I see is the connection via computer to the factory screen. So, I researched both obd units online.....quite affordable, do you need both units to complete the install? Also, you need a license for the fourscan in order to complete installation, if so, I haven't researched the cost of a license yet. Is there another alternative other than a visit to Ford for the computer connection connection??????
The Forescan licence is (or was) free if you sign up/join their forum. As far as the OBD units, you should only need one as long as it has the switch to change between the 2 modes (should be a link to one in the video description).
Thanks man! You saved me over $600. Camera went bad on 2016 F-150. Dealership wanted over $1000 to fix. Bought the camera online for half of Ford's price and then installed it in 10 minutes using your video. Bought the USB ODB II for $20 and calibrated the new camera using your instructions. The process of downloading the software and getting a license was a little laborious, but when it came time to connect to the truck and calibrate, again it took 10 minutes. So, the dealer wanted $1000 for 20 minutes of work...ridiculous!
I'm glad it worked well for you!
Thanks for the video. Am in the process of troubleshooting my backup camera and no one else has a video of how to disassemble everything, so this video helps a lot
Thanks! Hope it helps
Great video worked! Few tips! USB ODB is correct but my switch was wrong direction from instructions. When loading if ATC comes with an error, then the switch is in wrong direction for HS MS flip switch it’s in wrong spot. Also when it starting up and it wants to load the previous saved F150 say no. Your loading same file which is missing most modules like FCDIM. Finally when you write all it will say successful under log, but I had to press stop button before disconnecting. You need forscan extended to do changes. Btw 5 ford dealership in my area said it’s not possible. I was just replacing damaged OEM screen with stock camera. They said it was plug and play. Well ford has about 40 screens for same gen F150. Go bite a big one ford!
Thank you for putting this video up and also the link to wire from tailgate to hood. I saved hundreds of dollars and did it myself. Amateur tip, when wiring from back of tailgate to the front of truck remove the spare tire. I could actually sit under the truck while pinning the five new wires onto the connector. I work slow so this was nice.
Mike-sounds like you were successful. Mind answering a couple questions? Any issues downloading FORScan?
Amazing, I had no idea it'd be this easy to add a backup camera to my 2015 XLT.
Glad I could help!
GREAT INFORMATION. I just installed an electric braking system on my F 150 but got very little help from the parts dept at the dealer. Back up camera is next. Your video will make it much easier and massively shorten the time frame. Dp youknow what the wiring harness behind the coin holder on the dash is for. Thanks, again.
Just wanted to say thank you to Make Stuff Nation for the camera install, the author of the Ultimate XL OEM Backup Camera Guide for the, true to it's name, excellent guide to getting the wires installed into the existing harness. Thanks to the Forscan folks and all the help there as well. I'm very grateful for all the folks sharing their experience with newby's like me..
John..
Thanks you!
@The Gooberment-Sucks Yes, the video's I mentioned were a great help for adding the camera wires into the wiring harness..
John..
I really appreciate the very detailed video. I purchased the aftermarket camera, harness, and latch assembly for my Ford 2017 F150. I installed the hardware following your step-by-step directions. I used Forscan to change the code (7A5-01-01) from 2029 to 2229. Selected "Write All" in Forscan. Turned the truck off and on. I thought I was all set. Nope! When I go into reverse, there is a pause on my 4" screen, then it says "REAR VIEW CAMERA NOT AVAILABLE". The truck senses that there is a camera present as it shows up in the Menu. I have retraced my steps in Forscan and checked all the harness connections. I am unsure how to move forward! I would appreciate any help or feedback to solve my issue! Thank you in advance!!!
Hi Michael, I am having the same problem and I'm pretty sure it's because the rear wiring connector only has 2 wires and I will need to run wires from the rear to the front as described in the PDF. I do not feel comfortable doing this myself so I am looking for more resources or a good place nearby.
I'm having the same problem, my story is exactly the same as Michael's. Can you to tell me where to see the PDF you referred to?
Great video. Thanks for the complete process.
Glad it was helpful!
I tried reading your "The Ultimate XL Backup Camera Install Guide," which of course, is NOT informative, but is really Ultimate Unintelligible Gibberish. When I read a manual, such as yours, I cannot help but thinking, "Was it too much crack, or not enough?" Half-explained procedures, undefined parts, wires, slots, with a few nice pictures thrown in that tell little. But it's "Ultimate" so it must be good, right! I bought the stupid camera, and I need to figure out how to run wires to the front. I'm drowning here, and you're throwing me an anchor. Great job!
I didn't make that guide. I just linked to it. I was able to figure it out from that guide, guess you just need to brush up on your skills.
Hi ,I have 2016 f150 I try put back camera and used with screen 12.1 linkswell I buy same camera and wire you used on the video but the truck don't detect so can I used the forscan to detect the camera,
How do you know if your truck is pre-wired to allow this to work?
The PDF linked in the video description covers wiring and answers your question.
Hello Make Stuff Nation,
I watched your video and it is great on how to install and program the backup camera. I own a 2015 F-150 XLT Super Crew Truck and have watched several videos where a factory camera was installed in the tailgate, wires were run up the drivers side of the truck into the cab, uninstalled the screen, installed a special RCA plug and reassemble everything. Can you tell me where to look on my truck so I can decide which option I will need to perform to install a backup camera??? I look forward hearing from you soon. Thanks
Awesome video, but before you go and buy parts make sure your truck is wired for camera. If the wire harness mentioned in minute 5:50 only has two wires coming from the main wire harness, your truck is NOT wired. Don't even bother! I learned this the hard way.
The PDF guide in the description has instructions to run the additional wires. It is not very difficult just takes a little attention to detail.
Its not hard at all to run the additional wires. His PDF guide makes it easy.
Great Video!!! i notice this video was uploaded 4 years ago. the prices on the parts are triple!!! is it because of demand? or did you have a discount at that page?
I don't have any discounts. I guess prices have just changed over 4 years.
Thanks for the video and the descriptions. Perhaps, this has already been answered; is it the same install and set up for the Sync 3 touchscreen?
I'm not sure. I know its the same for the 4 & 8" screens but I'm not sure about the touchscreens. I would check the Forscan forums.
Make stuff nation I just purchase all the necessary parts including the wires and male/ female connector parts. Before I get started can you tell me if the male parts go under the truck or in the front and I assume the female connectors go opposite of the male connectors. Couldn’t really tell by the pictures and don’t see where it tells you which ones. Thanks
Good video. Someone has tried to install a intergraded tailgatestep on a 2018 f150 using this part Step Assembly - Ford (FL3Z-99402A48-AB)
How has it held up? I'm looking into doing it to a new to me 2017 F150 XLT. But, I'm weighing my options due to the increased cost for the camera. Although if you say that it's held up, I would feel better about purchasing a 300.00 camera.
It is still working well for me and I haven't had any issues since install. No idea if the parts/camera available today are the same quality as the ones I used.
Is there a schematic or something to have wires in correct slots on the end that connects to tailgate harness from front of truck? Wasn’t covered in the tutorial diagram or I missed something.
Thanks
sorry about that, here is the pinout:
Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck)
Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck)
Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck)
Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck)
Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
Great Video...This is so helpful. Now do the Bed (Cargo) Camera...:)
Thanks!
Great video! The pricing seems to have nearly doubled since your post however.
There are cameras closer to the price he listed on ebay.
@@SteveFullerBikes i heard in other forums that those on ebay do not work. They have to be OEM
Unfortunately the prices have really gone up over the past few years since I made this video.
My 2017 F150 has sync 3 but no backup camera, I was able to find a used oem handle with camera and harness, but after a closer look at my grey plug it only has 2 wires. Meaning my truck is not prewired for the camera.
@make stuff nation. I did the codes and plugged in the main harness. Do I have to have actuator power plugged in for it to work?
I would check the PDF guide that is linked in the description. Have you confirmed that you have all the wires run from the front harness to the back harness?
Great video, i had a completely unrelated question though, what are the dimensions of your garage? Ive been looking to build a garage and yours looks like the perfect size for the amount of space I have. Thanks!
I think it was about 12x20 but we moved out of that place so I can't get you exact measurements. Sorry.
@makestuffnation is there a code to get the tailgate handle led to light up? I wired my harness everything worked great! Just need my light to work.
hey make stuff nation....thanks for the video. helped a lot....I have a question though....i did all the process since I change my 4in screen and all works. the only thing missing is the zoom function that doesnt work when it used to. I checked through the spreadsheets but cant find anything to fix this.
Any idea for me ?
thanks again
I also have this issue. Everything works great but the "+" zoom button does nothing. Let me know if you find a solution.
Does this work for the larger touch screens? My husband has a 2017 Ford F150 XL also, and I really want to get him the set you got, but I want to make sure I buy it right the first time. Is this the best set, or is there an all in one?
Ginger UniKitty the wiring and parts should be the same for both screen sizes.
I'm having trouble trying to connect. I purchased the recommended OBD2 USB cable and I have it hooked up to a Windows 10 laptop. I pull up the forscan, plug it up, turn my key to on, and hit connect on forscan. Nothing this is on a 2017 F-150. I changed the APIM for nav features. I don't know if that would have anything to do with it or not, but it just will not connect.
Great video, I’m buying a 2014 XLT do you know if that model would be pre wired for a backup camera?
I'm sorry, I don't know.
nice camera work
Thank you!
Followed everything exactly. No camera detected. DTC error. Any idea where I might of gone wrong?
I have a F150 XL, you said it is already wired for the camera, is that true for all 2017 XL's? Isn't there a certain amount of wires needed in the molex connector to tell if it is prewired or not?
Some are, some aren't. It depends on the factory options. The PDF linked in the video description covers wiring and answers your questions.
Hello there, I perform everything as your video showed. My year model is a 2015. When I open FORScan I don't have FCDIM module, I do however have a BCM module. Any ideas where else I can find the rear camera setting? The spreadsheet provided has way more module than my FORScan shows. I am pretty sure that it the operator not the equipment issue that I am experiencing. Thanks in advance for any assistance. Greatly appreciated
Thanks
I'm the author of the FORScan tutorial & spreadsheets referenced above. What adapter are you using? If you're using the correct adapter that can access the MS-CAN modules as well as the HS-CAN modules and it has a toggle switch on it then try the following:
1. go into FORScan settings, connection tab and change "MS-CAN Support" to "HS/MS Switch"
2. connect to your truck again in FORScan but click no when it brings up your VIN profile
3. it should then find a few modules and then prompt you to flip the toggle switch on your adapter and find the rest of the modules
4. if it finds all modules then you can save this new VIN profile and use it on all subsequent connection attempts.
Did you ever figure it out I’m having that problem as well
Hi John, I'm using the Bluetooth version of the OBD connector on my 2017 F-150 XL. I installed the camera and had to install the wires in the harness... Great video and XL instructions! I'm also not seeing the FCDIM. Forscan is picking up both HS and MS CAN modules, just not this one. Is it possible the FCDIM is not installed on this truck?
Thanks,
John Skelnik, skelnik@us.net
I answered my own question from the F1-50 forum. Linked here: www.f150forum.com/f118/ultimate-xl-oem-backup-camera-install-guide-398123/index2/
Quoted here:
Quote:
Originally Posted by 10iron View Post
I intend to add an aftermarket camera to my 2017 F-150 XLT. I have seen it suggested that the modification with Forscan should occur at
726-39-02
7A5-01-01
7D0-01-01
All of these modication addresses supposedly worked. Any explanation for which point is correct or best would be appreciated.
Thanks for taking time to help.
JW
726-39-02 (all configurations) The value in the sixth place tells the BCM that a camera exists (0 for no, 1 for yes). This gets your dynamic lines and zoom working.
7A5-01-01 (4.2" screen only) The value in the second place tells the FCDIM that a camera exists (0 for no, 2 for yes).
7D0-01-01 (8" screen only) The value in the second place tells the APIM that a camera exists (0 for no, 2 for yes, A for yes w/obstacle detection)
To summarize: If you have the 8" screen, you need to change values in 726-39-02 and 7D0-01-01. If you have the 4.2" screen, you need to change values in 726-39-02 and 7A5-01-01.
Que buen video camarada chingon saludos
Thank you!
Awesome clip. I was just wondering if you knew the code for setting up with an 8" touchscreen
The codes should be the same.
I have a F250 for work but with a tool box style bed.
I added the rearview camera with a separate screen but I want to interface it to the factory screen.
I think I saw a 9 pin connector on the frame in the back so I wonder if the truck is pre wired for it.
I already have forscan.
I just need to figure out what wires are the composite video signal.
Did you figure it out?
well prices have doubled since you made this video! ;(
I'm sorry to hear that :-(
@@MakeStuffNation but i found an OEM handle with camera on ebay for $95 and i ordered the wiring harness..im all set now! Thanks for a great video
I followed your video, but when I tried to do the LIN new module scan, it wouldn’t work due to a few DTCs, any suggestions?
Make sure you are using an good MS/CAN compatible OBD II reader. I recommend this one: amzn.to/34qtT1N. If you already are, try clearing the DTCs that are present.
What Truck Stuff said
The backup lines overlay requires 2 pins shorted on the camera side. Not sure which. It's not a FORScan module.
Maybe on different model years. I was able to get it activated with forscan without shorting any pins.
This is a great help. I should not have to run any cabling if the truck comes equipped with a lock actuator in the tailgate correct?
Also, were you able to get the backup lines to appear on the screen?
Yes, I was able to get them working, use these steps (steps 3 & 4 turn on the lines specifically):
1: Connect ForScan, follow the prompts when connecting.
2: Under the FCDIM module, on the 7A5-01-01 line/field, change the 2nd digit from a "0" to a "2". Save/write the change (follow the prompts). (this activates the camera)
3: Under the BCM module, on the 726-39-02 line/field, change the 6th digit to a "1". Save/write the change (follow the prompts).
4: Click the wrench icon and run "LIN New Module Calibration". This makes the truck recognize the changes and calibrate the modules (follow the prompts).
5: Disconnect ForScan
@@MakeStuffNation when you say second digit, which 01 should change to 11? The first set or the second set?
@@MakeStuffNation Great Video! I installed everything just like shown in your video on my 2016 XLT which has the lock actuator. I took it to get programmed with Ford and they could not program it. I have not looked to see how many wires are running into it. Would the FORSCAN be the better solution?
Were you able to figure out how to get the guide/center lines to show up on your display? You mentioned there might be an additional setting you need to change...
Oh, I should have read the description in more detail. Is this covered in step 4?
David Mauldin yes, steps 3 and 4 activate the lines.
Hi David. Great video! Thank you! I got the camera working, but couldn't find "LIN new module calibration." Any ideas why?
Will this work with an F-150 2013 model XLT?
The physical camera install would take about a half an hour, and anyone can do that! What does it cost to just have the dealer boot the cam? $100 bucks next time I have the oil changed? Perfect OEM codes, no wasted time, no muss, no fuss, no nebulous codes and sketchy software and sketchier OBDII cables. Done and DONE!
Valid
Wondering if the backup camera would work with the base radio (no cd player)?
I'm not sure. I think it depends more on if you have the "Sync" screen thing.
Were can I get the harness and Camara and the handle can u let me know please and how do I know if it will work on my 2017 f150 stx
I put links in the description of the video. I'm not 100% positive if it will work on a STX but I think it should.
It seems as if my xlt only has the two wires. Is it possible to just purchase a replacement that is prewired that runs from the engine bay to the cab? Or does this have to be done manually? If so, what would that part be called so I could order it? Any help would be greatly appreciated!!!
Unfortunately if you only have the two wires, you will need to run the additional wires yourself. Because it is part of the main wire harness of the truck I don't think there's a part available to order. The PDF guide that I have listed in the description walks you through adding the additional wires yourself.
@@MakeStuffNation Okay. So according to the PDF I'll need to order some extra parts? Or could I get that all from an O'Reilly's for example?
good intellectual video, thx for it, to do this, it is not cheap other than your own free labor, the part cost at amazon is $300 and plus the computer software cost$190, hence, you can tell it is $500 already, no wonder the ford dealer at san jose northern california try to charge $1000 to install a back up camera.
Thanks. Yeah, prices on the parts have definitely gone up over the last few years.
Do all these trucks come with that harness needed? I have a factory camera
I did everything, and as I went to plug the new connector into the existing connector I saw the connector only had two wires, for the lock/unlock. After reading the instructions on how to add the 5 new wires I'll need, it would be easier (although more expensive) to replace the factory harness from the tailgate to under hood. Does anyone know the part number for the complete harness?
Thanks in advance.
I just got a 2015 XLT, I have the power lock like yours. I assume this will work on mine?
Yes, it should work. You just have to confirm that the additional camera wires are run from the front wire harness to the back harness plug. The guide in the description shows how to identify these wires and how to install them if they're not already there.
Changed my 15 tailgate to a 18 tailgate like the F150 detent in the tailgate. Everything was a bolt in swap (linkage) except for the handle ... then found out it has a different camera. Got all that changed and backup camera works but lost my guide lines. Plugged in the old camera and guidelines came back and was square even though the camera was dangling. Like you trying to figure out how to bring the guidelines back on the new camera I found this on the Forscan site but do not know the sequence to cycle the key. If you figure it out I would appreciate it!
Re: Code: B115E - Camera Module
Post by Echerr » Thu Dec 19, 2019 9:29 pm
I was able to fix my rear camera on my 2016 F250. My tailgate was stolen and after I replaced the rear camera with a new one the fixed and moving guide lines were missing. I was also unbale to zoom in. The DTC i had stored was B115E:55-0A. After i connected with OBDLink EX (usb to OBDII) I ran Forscan. Under the wrench icon I selected “Local Interconnect Network New Module Calibration” under BdyCM. After it ran I cycled the key to off and back to on as instructed. Both fixed and moving guide lines are now present and the zoom function is now working. Hope this helps.
Thanks. Glad you were able to get yours fixed!
@@MakeStuffNation not fixed yet trying to figure out how to bring the guidelines back on the new camera ... do not know how to do the the sequence to cycle the key ... do know the exact procedure to do this?
Hello I installed everything and flashed the system but the display is saying rear view camera not available.....any suggestions?
I'm getting the same thing on my 2016 XLT. I did not have the wires run from the back of the truck to the front, so I followed the instructions in the included link to run those. When I put the truck in reverse, I get Rear View Camera Not Available.
@@bouncebynum I'm looking to do the same install as you-somewhere either in this UA-cam listing or the F150 forum people talk about how they resolved your same issue. I have a 2018 camera/tailgate on my 2017 F150 XL and I've just been reading about it alot.
Were you able to resolve ?@@bouncebynum
@@EdGrube No, but I haven't had much time to work on it. I need to double check that I've got good continuity over the wires that I had to add to the connectors and that they're going from the right pins to the right pins.
After that: I've heard that sometimes the harness between the truck and the screen sometimes does not have the 3 video wires. I need to verify if that's the case in my truck.
@@bouncebynum Did you read below about some folks verifying that w/Ford?
I have 2016 F150 supercrew XLT. The factory harness is GL3T14B562KA. Will the harness you used be able to replace mine? And can I get dealer to flash software next time I get oil change?
The dealer can flash the software but they usually charge you extra. Not sure about the part numbers but they might be able to answer that question for you.
You didn’t have to do anything behind the dash right?
Correct
Great vid. I had to run the wiring per the PDF. Still getting "camera not available." I'm double-checking my pins now. Can you describe the location of pins 1-5 on the rear harness? (I did orient the wires exactly as shown in the PDF). My rear connector doesn't seem to be numbered. (The engine bay connectors are numbered). (I did orient the wires exactly as shown in the PDF). Edited to add: ordered a new camera and it works! Woot!
Pretty sure I figured that out--the PDF describes pin 1 as the upper right corner. So all my pins are correct. I have not been able to run LIN network new module calibration. Says I need to clear error codes. I have one error code B115E camera module bus signal. It will not clear. Haven’t found an answer as to what this is
Chuck-I'm trying to do this on my 2017 XL. Mind answering a couple questions?
I can try :) I did get it to work. Turned out I had a bad camera.
@@EdGrube
@@chuckthompson3358 I bought a 2018 tailgate with camera-hopefully no issues hooking this up. I'm assuming your was the 4.2 non-touch screen. What did you download from Forscan?
The Forscan Beta I think. And you get the extended license. @@EdGrube
Ok so I fucked up my tailgate and I was looking for replacements and I found an OEM with the back up Camera what type of harnesses will I have to buy to get it to work I have a 2017 XLT Crew Cab with the basics
Where do you buy the parts for the back up camera for an F150 2017
I just finished this on my 2017 XLT. Everything went exactly as described in this video and the linked guide for running the wiring. One final question: Has anyone figured out how to get the red/yellow/green lines to appear on the screen? I get the image with the magnifying glass and horizontal bar at the bottom of the image, but no multi-color guide lines on the sides. Also, the magnifying glass doesn't seem to do anything.
I had the same issue at first. I figured it out and wrote instructions in the description of the video. They should be pretty clearly labeled and easy to follow. It's just another module you have to activate in ForScan.
Great how to video, thank you. I have all the parts on your list and going to be doing the install this weekend.
I downloaded Forscan and somewhat familiar with it.
What was the code originally and what did you change it to exactly just to be sure.
Thanks again
Raf, did you end up going through with the install? If so how did it go? This looks too good to be true!
Mike Carroll I did and it was it easy like in the video. I got it all to work but I had to make a harness going from the backup camera to the front of the truck and tap into the stock harness. Pain in the ass
Thank you for the reply! I ordered the parts last night. You weren't able to connect to the stock harness back near the spare tire? Where did you access the stock harness at the front of the truck? Just in case I have the same issue...
If your stock harness doesn't have the connector/pins at the back, you will run lines up to the 2 main wire harness connectors under the hood mounted to the top of the drivers side front wheel inside fender cover.
After you ran the wires from the back to the front engine compartment, did you need to do anything with wiring behind the actual radio? I ran the wires, changed settings and get a “rear view camera not available message “
I do not have the 7A5 01 01 field as an option what does that mean?
If replacing a faulty camera with an OEM, DO YOU NEED TO CALIBRATE IT ?
You shouldn't need to if its the same part number. Just swap them out.
I just brought the same part number camera off of Amazon and I still have a black screen. Not sure what that means but I will try to reprogram.
Thank you
You're welcome
im kinda of disappointed i couldnt see what youre screen was showing, because that was the part i needed.... but thanks for the video!
Sorry about that. I need to get a screen capture program for my computer.
Im tring to activate my friends backup camera.
this activates the camera right? not just the "backup lines"
"To activate the backup lines on the camera:
1. In Forscan, edit 726-39-02 in the BCM, place a 1 in the 6th digit, and apply the change. This setting tells the BCM that a rear camera exists. It is on Livnitup's spreadsheet as "Slave Exists RVC"
2. In Forscan, click the wrench icon and re-run LIN New Module Calibration."
Okay, that part is to turn on the backup lines if the camera is already activated. Here are steps to activate the camera and then turn on backup lines:
1: Connect ForScan, follow the prompts when connecting.
2: Under the FCDIM module, on the 7A5-01-01 line/field, change the 2nd digit from a "0" to a "2". Save/write the change (follow the prompts). (this activates the camera)
3: Under the BCM module, on the 726-39-02 line/field, change the 6th digit to a "1". Save/write the change (follow the prompts).
4: Click the wrench icon and run "LIN New Module Calibration". This makes the truck recognize the changes and calibrate the modules (follow the prompts).
5: Disconnect ForScan
thank you so much!
Hello. I just got all my parts and install was a breeze due to your video. I have changed the modules and described but when I run LIN New Mod... it keeps aborting when I turn my ignition back on. Any advice?
Can someone show me exactly what the codes will look like when they are changed
I dont understand when it says change the 0 to a 2. And when its says changed the 6th digit
Could you bring it to cord to have them do the forscan on it?
I believe so. Not sure how much they would charge.
thx for the video...can you also add rear parking sensors in ther same manor?
Mark Andrews I believe so but I don't know how the wiring harness works for those. I assume they use different lines and pins.
Is there a way to install a front camera and how would it tie into the screen?
It is possible to install front and side cameras but I'm not familiar with the process. Sorry.
Nice work.
Thanks!
Never mind I found it!!
Awesome!
Is the backup camera wiring there for Canadian F150s? I have a Canadian 2017 XLT F150 with 4" screen.
I assume the wiring it the same on both models. You'll just have to check the harness at the connectors and see if they ran all the wires or if you'll need to add some.
@@MakeStuffNation What do you do if the 2 front harnesses already have wires in them?
I'm considering adding a camera to my 2017 XLT. I'm wondering if it is pre-wired like yours was. The existing connector to the tailgate that's by the hitch only has 2 wires coming in and out. I'm guessing that means my truck was not pre-wired, correct?
Gonzoagg09 that is correct, if it only has 2 wires you need to run the 5 camera wires from the engine bay back to the connector. See the ultimate backup camera guide file posted in the video description. It's a pretty easy process. Unfortunately I don't have video footage of that install.
Awesome! Thanks for the help!
I have a 2017 XL and also only have the two wires. what wiring harness would you use for that? Can I use the one you did ? I’m trying to find a wiring harness that’s already wired and I can just connect and run through to the back of the screen and I have the 8 inch sync 3 does the the forscan work for that ? Thank you for any help or advice you can offer
So, I installed this exactly like the instruction in the PDF. I ordered all the parts mentioned. Wired it up just like it said. loaded the FORScan stuff, and it works, but the image is update down. Any ideas?
1 - Brown - 33
2 - White - 7
3 - Blue - 11
4 - Green - 12
5 - Black - 13
2017 XLT 4.2" screen
Camera upside down?
@@EdGrube no, it only mounts one way
Did you get it resolved? Not trying to be a smart a** but some mentioned the lense on the camera itself may turn 180 degrees
EdGrube No, Not yet. I have come to the conclusion that I have it wired correctly, and it is either the wrong camera for this application, or the camera was assembled incorrectly. I wondered if I could just flip the assembly around, but it looks like the plastic assembly is welded together. I was trying to get the supplier to send me another one before I wreck this one. If the supplier won't send me another one, and I'm on my own, I'll try forcing it apart, or I will have to flip the whole assembly and silicone it in place.
@@CVALOVIC Any update? I want to ask you a bunch of questions
Where do you get the 4scan software???
There is a link in the video description (4scan tutorial)
So I bought everything from Tasca Auto Parts as the video suggested and the OBD II and download Forscan. Installed everything and when I changed the numbers as it stated to in the video and the notes I get an error stating backup camera not available. Also I get a code error when I do the LIN calibration. Can you please help me out with what I am doing wrong. I looked at a lot of forums and a lot of people are experiencing the same issue. I really don’t want to take it to FORD as they are going to charge $180.00 to flash the chip.
It is on a 2017 F-150 XLT with the non-touch screen. Basically the same truck in the video just one year newer
I am experiencing the same issue. If anyone solves please post. i bought a camera that i though was OEM but was a doorman, ordered OEM. Still same error. I will check for 9 pin vs 3 pin next. I also added the led bed lights that came with the harness for the camera. I threw time and almost 300 dollars at this and still no luck. disapointing.
I have installed the OEM camera and ran the 5 new wires as per the video and pdf; however after setting up FORScan I am getting a “rear view camera not available” error via my 4.2 inch Sync screen. Does anyone have any idea on what I may be missing here or have you ran into this issue and found a remedy? Any help would be greatly appreciated
I am having the exact same issue. I thought it might be that I didn't have wires running from the front to the back but when I called Ford, they assured me by running my VIN that my vehicle was setup for a camera. I still have not been able to get an answer to this issue. Does anyone have any advice?
Bryan Huntley check the harness that you connected the camera to that runs to the front of the truck. It will visibly have 3 cables( not wired) or 7 (wired)
try checking the wires you ran for this pinout:
Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck)
Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck)
Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck)
Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck)
Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
Same issue. I don't understand how checking the wires helps? Are y'all saying I may need to change the pin configuration from how the harness is already set up? Everything is correctly plugged in as he shows on the video????
Chuck Thompson my originally was that My 17 f150 was not pre wired for the camera. After I followed the video instructions I had to also read the attached pdf and run wires from under the hood to the new harness that was installed via the video. As for my 2nd problem one of the wires (the ground for me) had broken and I had to re-run it. Everything was wired correctly; however I had to replace a wire and discovered this by checking to see which wires had power or not. I hope this helps ;)
Do u have the links from the places you bought all those things
They are in the video description.
I have a 2015 f 150 xlt lart. can the fact.back up camera be relocated I had to install a power h/c lift it block the camera view 😢😂
I dont have any way to do the programing. Will the 4dtech canopener work?
Not sure. I know the dealers can flash/program it for you but they usually will charge you.
Hi Make Stuff Nation, i have a dumb question. I understand that the color of the wires are irrelevant. I am building the wire harness for truck side, the tail end connector will use the slots from 1to5 and the front will be 7,11,12 and 13 on one connector and the on the slot 33. The question is the following: what is the relation of the pin numbers beetween the aft connector and the front connector?...1 goes to what pin on the front connector? 2 goes to what pin on the front connector etc. Do you have a wire diagram? I need to know the order. Please help.
Okay, I just checked my truck and confirmed the pin layout. Here it is:
Rear Pin 1 -> Front Pin 33 (red in PDF guide, yellow in my truck)
Rear Pin 2 -> Front Pin 7 (white in PDF guide, purple in my truck)
Rear Pin 3 -> Front Pin 11 (blue in PDF guide, white in my truck)
Rear Pin 4 -> Front Pin 12 (green in PDF guide, red in my truck)
Rear Pin 5 -> Front Pin 13 (black in PDF guide, blue in my truck)
@@MakeStuffNation Great. Thank you for quick reply. This is a big help.
Good afternoon, i have a question. On the tutorial to reprogram the codes. I need know if the numbers are HEXA or Decimal
Hello Make stuff Nation, i am on last step of this project. I have built and run the new harness. All parts installed. Reprogram the Codes. I am getting the Rear veiw camera not available message. Anything else that i need to do? Or maybe a video that can help? Please help me.
@@MakeStuffNation What do you do if the front pins already have wires in them?
Where did you get the parts ?
Links are in the description but prices have probably changed. It was several years ago.
Hey I followed the video to the T and I'm not sure where I can get the link for the software?
There is a link to a FORScan tutorial in the description that has all the info and instructions on how to download and use the software.
Anybody able to get this to work on 2016 XLT model? I did all the wirings to the instructions
and installed everything. Took to local Fortd dealer to get it activated ($49.99 activation), but
they couldn't get it to activate. Do I have to get FORScan and do it on my own?
Great video and instruction by the way.
So finally got time to get the backup carema to work on my 2016 F150. Tested the resistance on Pin 6 and Pin 12 on the back of the display unit( got 73 ohms). A plus was that the harness to the display was pre-wire for these two pins (I took the connector that plugs into the display apart). Downloaded Forscan and followed the instructions on here. Was able to get the guide lines and centered black line to come on also. Thanks to all those who pioneered this mod.
Hopefully someone can help me. So my truck came with the tail gate camera and was already wired. Nothing would appear when I put it in reverse. Got Forscan and did the numbers they said use. Now I get a blue screen in reverse. Iv swapped camera and still the same. Any help here?
What other update like htis can I do on my 2017 Effy?
Sorry I'm not sure
FYI, Ford parts for this project around $800 to $900 CDN, CAMERA ALONE IS OVER $600 CDN
Yeah, prices have changed a lot.
Not seeing 7A5 only 7A7, is there a difference between the two?
Seems those with 8-inch screen's don't have to worry about the 7A5. Now I just need to run the wire from the front to the back.
Will this work for an aftermarket head unit? is it just a yellow video input?
It is not a yellow video input, this wires directly into the Ford sync harness.
great video and nice camera work. Do you think those parts you listed in the description would also work for a 2016 xlt 4x4
Mike Osvold I think the parts should be the same for 2015-2017 but I can't guarantee.
Mike did you ever figure out if it worked for your 15' XLT? I have the same.
gtdave86 no I didn't. I will look more into it in October when it's not 109 degrees in my garage.
Where can l download forscan software? Thanks
Just install the camera on 2017 f150 xlt. Can’t find step 4 “LIN new module calibration”. ( is the forscan version different from yours?) The screen has no image, only show “rear view camera not available”. Do you think is cause by the hardware or software.
I, too have my screen saying “rear view camera not available”. Did you find a fix? Has anyone else ran into this?
Jason Deptawa oh. My truck was not prewired. I follow the guide to ran wire to the engine bay.
Same here - I had to run the wires also to the engine bay. Did you get the message to go away? After wiring I’m still getting the error message
Jason Deptawa yes. It fixed. It show image immediately after I ran the wire. Then I activated the line. I think the problem is the wire or camera.
赵崇敬 interesting - I appreciate it and I’ll continue to work on this ;)
will this wire assembly work for the tailgate handle that has the light on it ?
No, I believe the wire harness for a tailgate with the light has a different part number.
Hey. Dose this works with a 2015 F150 xl ?
Yes, it should work with the 2015 model year.
Can anyone tell me where this guy got the pigtail and tailgate handle from? I can find some handles, but no wiring for my back up camera like the one he has.
There are links in the description but unfortunately prices have gone up over the last few years since I made the video.
Are u know 2020 f150 tailgate handle fits for 2015-2017 Sir?thanks
Sorry, I don't know.
Does anybody know if this will work without the LIN BUS communication wire?
Will this work with the 8" screen as well with sync 3? Thanks
I believe so. The wiring from then engine bay back and ForScan settings should be the same.
Were did you get the parts from ? For 120 ?
www.tascaparts.com/ for the camera, tailgate harness, and handle.
@@MakeStuffNation do you have the part numbers for each items you ordered?
is this the same procedure for a 2017 F250? thanks
thats what I'm wondering.
300 bucks and about 10 hours no back up camera. I did the door key pad though. Good luck!
Great video for the do it yourselfers! The only problem I see is the connection via computer to the factory screen. So, I researched both obd units online.....quite affordable, do you need both units to complete the install? Also, you need a license for the fourscan in order to complete installation, if so, I haven't researched the cost of a license yet. Is there another alternative other than a visit to Ford for the computer connection connection??????
The Forescan licence is (or was) free if you sign up/join their forum. As far as the OBD units, you should only need one as long as it has the switch to change between the 2 modes (should be a link to one in the video description).