Limp Mode Maxima

Поділитися
Вставка
  • Опубліковано 22 гру 2024
  • 2007 Nissan Maxima in "Limp mode" and it's NOT a CVT issue??
    Autonerdz is the place for all Picoscope needs.
    autonerdz.com/...

КОМЕНТАРІ •

  • @cindylovesdarren
    @cindylovesdarren 2 роки тому +1

    Man I've been working on my maxima for two weeks looking for why my throttle was functioning all wacky and I had the abs light on... I was looking everywhere for the freakn problem thank you this explained so much

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому

      Thats awesome. I've personally gotten great tips from YT on different projects, so I'm glad my content is helping others! Thanks for commenting.

    • @robertollamas7782
      @robertollamas7782 9 місяців тому

      I replaced my throttle body and dealing with these types of issues

  • @paulmandeville
    @paulmandeville Рік тому +2

    Finally, a breakthrough. When I removed the rear rotors for a brake job, I had to use a puller and wail on it to remove both rear rotors. Apparently that loosened metallic dust onto the magnetic ring. I could actually count the magnetic poles the dust was so thick. While I was at it, I replaced the bearings and the car is now running normally. BTW, if you disconnect the sensor with noise or hash….you will get errors displayed, but the car will run normally! Thank you for the post which pointed me in the right direction!

  • @vickenkaragozian2041
    @vickenkaragozian2041 2 роки тому +3

    Wow thats amazing mr. Carter. Yes anything can fool the ecm and fool the technician. Never thought that wheel speed sensor would do this. I appreciate sharing with us, as usual great information. 👍

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      Hope it helps, especially if you are faced with diagnosing a car with these symptoms. And yes there are many rabbit holes a technician could fall into with issues like these.

  • @eacherenkeka
    @eacherenkeka 2 роки тому +2

    Excellent video Carter! Good diagnosis and save some money to the customer! I've had some wheel speed sensor problem without codes but usually engages the ABS motor and you can feel vibration! More in aftermarket components! Great job Carter! Thanks for sharing!

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому

      Thanks for commenting 🤘. I have experienced the vibrating pedal problem before also, a good graphing scanner helps with those also.

  • @BigDogDiagnostics
    @BigDogDiagnostics Рік тому +1

    Thanks for sharing that. I could see that issue sending many good techs down some rabbit holes!

  • @High_Tech_Mountain
    @High_Tech_Mountain Рік тому +2

    This is definitely an interesting one! Thank you for sharing!

  • @paulmandeville
    @paulmandeville Рік тому +3

    I see the beginnings of this : rear wheel bearing corrodes and breaks down, the iron dust migrates to the magnetic ABS ring and pollutes the signal. This happens especially during a brake job if you hammer on the rotor in order to remove it. If your rear wheel bearings are rumbling, exchange them ASAP.

  • @shaffere33
    @shaffere33 Рік тому +2

    Interesting issue there. Definitely can see that one having the parts cannon blasted all over it. Nice diagnosis

  • @Z14kt12timandjes1
    @Z14kt12timandjes1 Рік тому +3

    Wow, you saved that customer a lot of money! I really am enjoying your videos. Thanks for all the knowledge you are sharing with us. I found this video by searching for a solution to my son's Nissan Frontier supercharged truck. He's having an issue that he describes as it intermittently switches from feeling like a V6, to feeling like a 4 cylinder. Still totally drivable, but much slower. Kind of thought it was pertaining to the supercharger at one point. We could clear the knock sensor code and it would seem to improve for a little while but then it would do it again. Ever seen anything like that or do you have any videos you could point me to where you have been over that type of thing?

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому +2

      I'm glad you found my channel and commented. Take a very close look at the distributor, meaning take the cap off, take the rotor off, take the cover plate off (2 or 3 Phillips head screws) . Look for any metal particles especially on the signal plate. Check for excess play in distributor shaft. Also inspect the coil, look for any signs of it arcing to the distributor housing.

    • @Z14kt12timandjes1
      @Z14kt12timandjes1 Рік тому

      @@CartersDiagnostics thanks! I'll let my son know and we will check it out. Thanks so much.

  • @sebry25ify
    @sebry25ify 2 роки тому +5

    Awesome video. This is crazy. Definitely the guy who wrote the ABS program is not smarter than you. I look forward to seeing your CVT video.

  • @johnnigro4536
    @johnnigro4536 2 роки тому +2

    Excellent critical thinking. This could easily take someone down the garden path! Here in Canada 🇨🇦 that bearing would never come out in one piece for a quick wipe 😆

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      Corrosion is a terrible thing, it can make an easy job into a career with the snap of 1 bolt🤬😠 Thanks for commenting.

    • @emilebernard5970
      @emilebernard5970 Рік тому

      @@CartersDiagnostics do you have a phone number I could call you on Please Sir? I need help with my 2011 Maxima doing this same thing

  • @fitzgeraldparkman3727
    @fitzgeraldparkman3727 2 роки тому +1

    My 2009 maxima sv is presently doing this , thanks to your video hopefully i may have found the problem , I wish I stayed in your city so i could bring it to you

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      I hope its nothing major and you get it fixed! I appreciate your support 🙏 and comment.

  • @00blowngt
    @00blowngt 2 роки тому +1

    Really appreciate your videos and time. Very informative. Thank you!

  • @uusa35
    @uusa35 Рік тому +1

    thank you so much for sharing such important and valuable information

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому

      💯👍

    • @uusa35
      @uusa35 Рік тому

      thank you so much really
      i have Judder P17F1 (maxima 2016)
      u think it may be a possible the coil (Misfire) and clean rear wheel bearing also or it's absolutely CVT failure
      it only happens when i drive the car for long distance and get hot but the temp indicator is normal
      i cleaned the fuel pump filter and also catalistic converter / MAF / changed the battery but no use
      when i press fuel it does not response RPM goes high for just 2 / 3 seconds then when i press again gently it starts moving.
      also while i am pressing the fuel padel i feel a very tiny small hesitation in the rpm indicator
      please kindly help me
      @@CartersDiagnostics

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому +1

      @uusa35 There is a very specific repair procedure for that code P17f1. Refer to Nissan Technical bulletin for guidance. The number is NTB17-039P

  • @veronicadye7276
    @veronicadye7276 9 місяців тому +1

    Hi if my car isn’t going pass 3k Rpm Is it the throttle body I should replace or the transmission? It starts right up I don’t hear any noises I changed the valve body , mass air flow sensor and everything else I thought could be the problem except throttle body . I don’t wanna buy new transmission and there is nothing wrong .

  • @screamersnsp4229
    @screamersnsp4229 Місяць тому

    I’m having the same issue with my 2014 maxima everytime I come to a stop it takes about 3-5 seconds to engage again what’s my issue!

  • @ablackformula
    @ablackformula 2 роки тому +2

    Does the ecm have some sort of pid to show torque reduction request or something similar? It would be handy if the ecm could give some info as to why it's making silly decisions. I could see someone looking at the app vs tps pids and replacing the pcm and/or throttle body assembly.

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому

      I don't remember seeing a reduced power type pid on this car.
      I will have to poke around on some newer stuff and check for it also.

  • @ngsacid2224
    @ngsacid2224 9 місяців тому +1

    I just bought this exact car and im pretty sure this is my issue. Abs light on for right rear sensor, ill be sure to change the hub as well. I thought it was a cvt issue as well but I'd be much happier with a $70 part vs $3000+.

  • @lpin9365
    @lpin9365 23 дні тому

    My 2004 Maxima has 143000 miles and it seems to be stuck in limp mode: goes into 5th gear when put into drive, and jerks when put in reverse. It started intermittently but now it is permanent. The «Service Engine Soon» light is off. Is this a «limp mode» case?
    Some checks and part replacements around the transmission have been made, with no success. Shall I try to go for a general cleaning of all 4 Hub bearings? What do you think?

  • @edwardboers1993
    @edwardboers1993 2 роки тому +1

    Good stuff brother.... another great video 👍

  • @markferraro5250
    @markferraro5250 2 роки тому +1

    Great video CARTER thanks

  • @darealallgrindnoplay
    @darealallgrindnoplay Рік тому

    I have a 2014 maxima the abs pump code came on scanner when I bought it from someone week later it keep goin into limp I changed the battery fuse box what could it be abs module or alternator?

  • @arthurlewis9865
    @arthurlewis9865 Рік тому

    Where are you located I have a 2007 Nissan Maxima with the CVT transmission 3.5 engine as a transmission fluid pressure switch problem

  • @Luisturbog1
    @Luisturbog1 Рік тому +1

    I’m about to go check if this is my problem. I’m going crazy with this problem. I was thinking maybe my cats were clogged

  • @Gregman2274
    @Gregman2274 Рік тому

    Same issue with my 09 maxima but it doesn’t give me any error codes, when I replaced the fluid it drives fairly fine but eventually Glen into limp mode. Can someone please point me into the right direction

  • @willy0287
    @willy0287 7 місяців тому

    Hi sir! I have a huge issue with my Versa 2020!! Unfortunately I came to Mexico and I don’t trust mechanics here! You think I can have like a phone consultation with you? I’ll pay for it with a transfer or something

  • @RahimSuggs
    @RahimSuggs Рік тому +1

    Very helpful

  • @ivandrago2557
    @ivandrago2557 2 роки тому +1

    Very valuable informations, thanks

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      Hope it helps.

    • @ivandrago2557
      @ivandrago2557 2 роки тому +1

      @@CartersDiagnostics Priceless , Every detail is explained couldn't ask for more glad to found your channel

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      Thats great. Glad your here! Sometimes I repeat myself , but I try to be thorough . I appreciate your involvement.

  • @paulmandeville
    @paulmandeville Рік тому +1

    Please tell me your scan tool name/type. Mine will not read the wheel speed sensors

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому

      Its the Snap on Zeus.

    • @paulmandeville
      @paulmandeville Рік тому

      @@CartersDiagnostics Thank you…I have the ABS limp issue, however my scanner does not see the wheel speed sensors……..but I don’t have $$$$ for Snap-On tools 😹 Do your know of other scanners which are compatible with 2007 Maxima ABS? I would like to pinpoint the problem before tearing things down.

  • @chekelley6861
    @chekelley6861 2 роки тому +1

    I had a Nissan that would only go into limp mode if the headlights were on. Replaced a taillight assembly and fixed.

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому

      Crazy how that circuit works. I see taillight issues on Nissan Versa more than any other for some reason.

  • @mariob1653
    @mariob1653 2 роки тому +1

    I probably had replaced the cvt😹😹 excelente approach

  • @Sergio09354
    @Sergio09354 2 роки тому +1

    hello again. excellent video , thanx for sharing. i watch most of my videos on my apple tv, does it helps your channel with the views that way
    or do i need to go to my phone and watch it there? i see you added the video which is great ! do you own your shop or work for somebody else? anyway keep up the good work i know it takes time to make videos.

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      As far as views I don't think it matters to UA-cam how you watch. I appreciate the views and comments that's what matters!! 👍🙏
      I work at other shops part-time and self employed .
      The videos aren't to bad to make, mainly because I'm not that high tech,I like simple and to the point videos. Sometimes saving the content while on the job gets interesting, especially if I have alot going on and I need to do extra testing for the channel, but its worth it.

  • @NighTimeProductions
    @NighTimeProductions Рік тому +1

    Hey! I have a 2008 Nissan Maxima SE, my CVT transmission is the same as a 09 murano. 6 months ago me and my father tried a break flush but nothing came out of the back break calipers. 3 weeks ago I noticed a noise from my engine getting louder. (A low fluttering) along with that less power. We changed the fluid and put in a new internal and external filter. My engine sounds better now, but the CVT has a loud squeal right after the fluid change. When I first started it, the battery was dead and the dash flashed. So I jumped it and tried to warm up the fluid to get a hot reading. The level was fine, but when I tried taking it for a drive, it was now completed stuck in limp mode in first gear. Could this be an abs issue? I’m guessing there may be multiple issues here. Like abs, break switch, and CVT. Let me know what you think.

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому

      Scan for codes first. Unplug the ABS module and how the car reacts. Did you use the correct fluid? Very important.

  • @paulmandeville
    @paulmandeville Рік тому +1

    Was this car shifting properly?

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому

      The throttle would go dead before any real speed could be reached. If I remember correctly, it felt ok up to the point of failure.

    • @paulmandeville
      @paulmandeville Рік тому +1

      @@CartersDiagnostics I just made a strip chart of the wheel sensors….both rear sensors have extraordinary hash compared to the front. The car throws no codes and will not shift above 3…and the ABS activates just before stopping.

    • @CartersDiagnostics
      @CartersDiagnostics  Рік тому

      Sounds like a worthy time investment to put a visual inspection on the ABS components.

    • @paulmandeville
      @paulmandeville Рік тому

      Made a 2nd strip of pedal positionvs throttle position…and as you demonstrated, my throttle is being clipped at full pedal position!

  • @bandidorich7788
    @bandidorich7788 Рік тому +1

    My 2010 maxima is doing this, and the battery is draining

  • @screamersnsp4229
    @screamersnsp4229 Місяць тому

    You’re my only savior rn can you please help me 😢 it literally runs good on the freeway and everything it’s just when I come to a stop it takes a while to engage I don’t believe I neeed a new trans

  • @davidwhidden3968
    @davidwhidden3968 2 роки тому

    I have a 2007 maxima and the rpm will get up to 6000 rpm and speedometer only gets up to 30. Would that be the cvt or start with the hubs as you described

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      I would think if the RPM is going that high, the throttle is not being limited by the traction control system. I would focus more on the cvt, and determine if its slippage or not.

    • @davidwhidden3968
      @davidwhidden3968 2 роки тому +1

      @@CartersDiagnostics before I got the car the original owner said it would run hot at times cause the fans didn’t kick on I replaced the fans and still nothing but if you pull the fuse under the hood the fans would turn on but no start. Would cooling system cause that in the CVT ?

    • @CartersDiagnostics
      @CartersDiagnostics  2 роки тому +1

      Its probably an ECU fuse you are pulling, by default it turns on the fans due to lack of communication.
      I doubt the cooling system causes the cvt issue. I have driven alot of over heating cars that the transmissions were fine.

  • @terrencebaines8899
    @terrencebaines8899 2 місяці тому

    Good job

  • @RayColldo
    @RayColldo Рік тому

    Waoooooo nice.

  • @trentdq
    @trentdq 2 роки тому

    knowledge on code p0746