@@ErikRose_takes one fucking minute to do and saves youre whole electrical system. whether youre working with electronics or not, moving a piece of metal under the hood can easily touch a hot and ground causing a surge which breaks half the shit. but if you doin it at your own risk then wtv🤣
Headers should free up power if you had a lot more exhaust. But it makes it sound better and look better. It’s all part of it! Awesome truck. It needs LS ported heads and upgraded injectors and pump. Time for the big money mods!!!
I love we can inspire and motivate people to build some bad ass trucks or any vehicle. As always we appreciate you’re support and watching the vids.. 🙏
@@misaelmendoza2650I think you can just google flash shark headers for your truck and they should come up the whole kit was like 500$ I think it maybe cheaper
Thank you so very much for taking your time to make this video, makes me feel a lot better about making the purchase and hella thank you for the 15% off promo code!! I like your truck, it's really nice. It is my hope that you and your family are in good health and staying Covid free.
🔥 as usual bro, but those gaskets that come with the headers are trash. Over a few months the headers will burn through them and cause a leak. You have to use OEM manifold gaskets because they’re MLS
Becaause of this video I pulled the trigger and put a set on my 02' Suburban. Got the exact same set from JCarpart for less than what FlashShark had them marked up to.
Did you notice a difference with these headers and are they a good quality set? And how are they holding up now? Thinking about doing these headers I just seen there a little on the cheaper side
They are holding up great, but I recommend getting the stainless one because the paint come off the black ones and fitment was ok driver side fit great but passenger side needed some massaging. But this could of been because of my old motor mounts being worn. But nonetheless it could still possibly be an issue.
Hey man I ran them jdmspeed wires but they only lasted 3 months and started misfiring get the MSD wires when u can bro don’t wanna ruin that motor. Truck is badass to
required a few love taps bro 😂 but it could be because my engine mounts are worn out i’ve heard that could cause longtube headers to not fit perfectly.
No it does not have any provisions for the downstream o2s. I just zipped tied them out the way. And you might have a checked engine because of this but I had mine tuned out or you can possibly use some spark plug defoulers to trick it.
I just got done with short tubes on my tahoe, I've been plannin on upgrading to e fans as well as the same aluminum radiator, but would you recommend a stage 2 cam? I would've liked a stage 3 but I already average like 12mpg city, 8mpg with e85, and don't wanna have to deal with changing the stall converter as well
Hey man, I love the trucks. I’m going a lot of similar things with my truck. Do you run a tune on your truck? I just recently got a set of long tubes and I’m fairly new to modifying my truck. I want it to run properly. If I were to get it tuned, what would I need or where would I go to get it done?
Thanks bro, Yes I do run a tune on my truck only because it has other mods like a cam and injectors etc. you don’t really need a tune for headers, the only thing is you’ll get a check engine light. So you can get that tuned out or there’s other ways too without doing that. As far as a tuner It depends where you are, but in socal there’s a lot of tuners that you can go to.
Appreciate it brotha! on the rear its on 17x10 rim with 305/45/17 tire and the front is a 20x9.5 rim with a 245/40/20 tire although i recently switched to a 255/45/20 tire for a meatier look
In your video you said something about misfire. Would these headers cause that or check engine light to come on just wondering before I buy them for my truck
Nah the misfire was for something else, these headers will be fine but you will get a check engine for your cats because these obviously dont have any cats but not a big deal if you dont care👌
Low end you’re not for not long tubes they lack the power the power in the on the low end unlike the short tubes but then long tubes on top end gain power
Disconnect the battery before you even begin anything.. your computer will do a little soft relearn and comprehend better with the AFR, you still need a tune but it’s better than just cranking it on and relearning while your driving without disconnecting the battery beforehand.
Why does he keep saying we when the other guy was doing all the work and he was holding the camera? With the exception of when he wanted to show a part then the other guy was holding the camera?
Cutting and fabricating. We made it ourselves but you can buy bezels and just cut it out and weld the tip of your choice. Or if you don’t have the tools I’m sure some muffler shop can do it for you.
Speed engineering 1 7/8 header long tubes I on my 00 suburban no love taps needed. Didn't even take out the spark plugs surprisingly But love taps add a little power 🤣🤣 I need those wheels!
@@ErikRose_ Ive had so many love taps hella maybe some love smacks🤣 on my rides lol. I think even road kill had a set of beat headers that made more power lol. Thanks bro! Imma see if I can get those wheels in 22s I want them
I noticed your trans crossmember was modified and don’t have that bigo chunk in the bottom it sits flush with the frame y’all did that or bought it like that ? Only asked cause they do that when they hella low and don’t wanna bend the oem crossmember.
“Hear that chop better” truck proceeds to have no chop to be found.
My thoughts exactly!!,. Poor guy doesn’t have a clue about this stuff!
I figured his tune was off lmao idle too high
He had a stock converter that’s why and well the tune
The catless cats cancel the chop 😂😂
It's not cammed.
Lol those sparks from when you took out the dipstick is exactly why you should disconnect the battery 😂😂😂
ehhh its more work 😂😂😂
@@ErikRose_takes one fucking minute to do and saves youre whole electrical system. whether youre working with electronics or not, moving a piece of metal under the hood can easily touch a hot and ground causing a surge which breaks half the shit. but if you doin it at your own risk then wtv🤣
Headers should free up power if you had a lot more exhaust. But it makes it sound better and look better. It’s all part of it! Awesome truck. It needs LS ported heads and upgraded injectors and pump. Time for the big money mods!!!
Injectors…?
He could port it himself
Hell yea bro you inspire me to get another truck and make it a race truck, love the progress on the build so far
I love we can inspire and motivate people to build some bad ass trucks or any vehicle. As always we appreciate you’re support and watching the vids.. 🙏
Take it out of 1st gear sometimes lol.
that was my thought as i was editing 💀 definitely want to get some highway shots/pulls in the near future 💯
Where did u got those long tubes heaters from ?
@@ErikRose_hopefully u respond I need get those 🫤
@@misaelmendoza2650I think you can just google flash shark headers for your truck and they should come up the whole kit was like 500$ I think it maybe cheaper
@@misaelmendoza2650the link is in the bio
Yeah. I'll bet your neighbors love you.
contrary to belief they actually do! My neighbor to the right has 93 Supra and my neighbor 2 houses up has a Mclaren 720s lol
I be blipping my throttle like that everyday 😂😂😂. Chevy gang
its too fun bro !! 😂
True duals I'm going straight back
13:54 love that cruise pov can you do more with same filter just love the whole view and sound
Definitely plan on getting more driving POV’s for you guys its coming! 🤙
Thank you so very much for taking your time to make this video, makes me feel a lot better about making the purchase and hella thank you for the 15% off promo code!! I like your truck, it's really nice. It is my hope that you and your family are in good health and staying Covid free.
of course bro not a problem glad i could help! Thanks for the kind words! 🫡🤝
I can’t be watching videos like this man I’m trynna save money 😭
i got a giveaway rn for some that free 😂
Sounds good and looks good and about 20 ture horsepower on headers
Forsure! Huge torque difference with these!
Another banger video. Would love a video of you taking it to your local drag strip and see what it runs
Definitely a goal of mine! I would love to get that footage for the channel!! 🔥🔥
Definitely be in the 15s I’m mid 14s in 33s inch tires got a few more things done to mine
Los Angeles no 1/4 mi tracks within hundreds of miles. All gone
That thing idles like a singing machine! 😂
Music to my ears 🦻
yea i gotta step in the truck lane that thing look and sounds goods 🔥🔥
its fun bro and something different 🔥
I’m in the process of building a 5.7. Vortec 350 but carbureted for my 05 silverado
nice! 🔥
🔥 as usual bro, but those gaskets that come with the headers are trash. Over a few months the headers will burn through them and cause a leak. You have to use OEM manifold gaskets because they’re MLS
Appreciate the info my boy! I wasnt really worried tho I wont have them for long, I will have to change everything once again when i boost it! 👌🔥
the build going fire asf congrats brotha
Appreciate the support my boy fr! got lots more heat coming ! 🙏🔥
I saw sparks when u remove oil dipstick?
right me too?
Good catch I didnt even notice that when we were doing it, probably from the dipstick hitting the top of the spark plug is my guess lol
🤣
Nice job my friends co build..
was there a noticeable power difference? and do you think other long tubes would provide more performance or these are the best bang for your buck?
Take a shot everytime he says. There you have it. Everyone will be fooked upppp 😂
“there you have it” and “thats pretty much it” 😂😂😂
If and when you ever come to Florida. Hit me up. I’m down for some truck racing.
yall got e85 out there imma need lots of it! 😂
Just to be correct, you took off the exhaust manifolds. Nice truck, what transmission are you usung?
I know i realized i kept saying headers lol but during this video it was a 4l60 with a transcooler currently upgrading to a 4l80e!
Nice looking truck. What kind of exhaust you running?
Becaause of this video I pulled the trigger and put a set on my 02' Suburban. Got the exact same set from JCarpart for less than what FlashShark had them marked up to.
Link
nice always good to find a better deal 🔥
I mean same site discount code fb20 found after i orderd.with your discount code! Lol
Did you notice a difference with these headers and are they a good quality set? And how are they holding up now? Thinking about doing these headers I just seen there a little on the cheaper side
They are holding up great, but I recommend getting the stainless one because the paint come off the black ones and fitment was ok driver side fit great but passenger side needed some massaging. But this could of been because of my old motor mounts being worn. But nonetheless it could still possibly be an issue.
@@ErikRose_ thanks! But 1 last question I should have asked did you notice a power gain? Big difference or just a little bit
Sorry for the late reply, but even though that they do give you some gains they’re not that noticeable.
That mf arked HARD 💀 when you pulled the dipstick tube out
It did we didn’t notice till we watched in the video 😂
Clean truck. No CAI with headers and cam? Always take out the plugs just to avoid breaking them, but you live and learn. Sounds good too
Appreciate it bro, yeah No CAI the plan was to boost so didn’t really care to install one. And yeah we were a little lazy to remove them lol..
The stock intakes on these trucks actually don’t flow that bad, the “cold air” intakes you find online generally just suck in hot air anyways
Idk how much HP you think them headers added?
like 10 max lol
That cam sounds like mine. -Stock- you need a TSP Stage 3 High Lift Truck Camshaft
Hey man I ran them jdmspeed wires but they only lasted 3 months and started misfiring get the MSD wires when u can bro don’t wanna ruin that motor. Truck is badass to
Hell yeah I'll keep that in mind bro thanks for the info and support!!🔥
@@ErikRose_ from the other side of the map 💯 NC
HE GOT THE LONGTUBES
ahhhh shit I know a legend named phil cotton ! 🗣️😂
Maybe I missed it but what about the rear o2 sensors on the new exhaust?
We had them tuned out by our tuner so didn’t install them.
Bro what did you mean at 4:35 when you took them off
required a few love taps bro 😂 but it could be because my engine mounts are worn out i’ve heard that could cause longtube headers to not fit perfectly.
Clean truck bro! Looks badass! Does the 305 rear tire rub on your bed? How close is it?
Thanks man, yeah it did I had to roll the bed to make them clear.
Nice bro I’m installing a 5.3 in my 2000 Chevy Silverado 1500 short bed will I still need to get my truck tuned after installing
nah as long as you keep it stock you should be good ! 👌
Was this whole video shot in first gear
Damn near 🤣
@@ErikRose_ LMFAO keep up with a good videos!!
Love the sound!
Besides the cam what else do you have done to the engine? New to your chanel
Pac Springs, Tbss Manifold, Longtube Headers, efans and running on an e85 tune. getting it ready for boost now.
Hey man side note what mic are you using clipped onto your shirt? Sound quality is great 👍🏾
Dji Mic! Its a bit pricey but well worth it ! 👌
Esta perrona bro cual es nombre de los spark, plug wires
se llaman jdmspeed en el amazon bro 🔥
On the downsteem o2 sensors, did you just ziptie the wires back or does this kit have a spot for all four O2 sensors?
No it does not have any provisions for the downstream o2s. I just zipped tied them out the way. And you might have a checked engine because of this but I had mine tuned out or you can possibly use some spark plug defoulers to trick it.
I'm getting some long tube . What about the egr delete?
Delete it you’ll be fine you’ll have a check engine light tho not a big deal if you dont care.
Love that truck!!!!
hell yeah boost is next ! 🔥
Texas speed makes some good ones
Texasspeeds are definitely better! Only installed these for the mean time boosting it soon so wont really matter ! lol
Lol you right. BoostedErik
bro kept saying “we” the other dude was doing mostly everything 😭💀
someones gotta record bro 🤣 but when i am doing something its usually not recorded lol
Does every header order come with clamps ?
Yeah it should bro 👌
I just got done with short tubes on my tahoe, I've been plannin on upgrading to e fans as well as the same aluminum radiator, but would you recommend a stage 2 cam? I would've liked a stage 3 but I already average like 12mpg city, 8mpg with e85, and don't wanna have to deal with changing the stall converter as well
My truck actually has the stage 2 cam from texasspeed and its great no complaints here! And I feel you on the gas my truck gets similar numbers! 😭
Darn 8mpg my avalanche with a stall and e85 get 11.3 mpg,but that’s the wife driving it.
@@mgbliz she be driving it like a prius so it really gets like 6-8mpgs 😂
Did new bolts come included?
yes comes with new bolts as well!
When installing these headers what is the wire kit it comes with for and those conectors
Honestly not sure bro we didn’t use them nor are they needed lol
Sounds great, looks awesome. Nice job.
Appreciate it bro!!
They ship to the us ?
they sure do bro!
When the turbo coming?😮💨
Might have something already in the works 🤫 😁stayed tuned brother….
Let me save up a lil more ! 😂 its coming forsure tho
Hey man, I love the trucks. I’m going a lot of similar things with my truck. Do you run a tune on your truck? I just recently got a set of long tubes and I’m fairly new to modifying my truck. I want it to run properly. If I were to get it tuned, what would I need or where would I go to get it done?
Thanks bro, Yes I do run a tune on my truck only because it has other mods like a cam and injectors etc. you don’t really need a tune for headers, the only thing is you’ll get a check engine light. So you can get that tuned out or there’s other ways too without doing that. As far as a tuner It depends where you are, but in socal there’s a lot of tuners that you can go to.
@ Thanks, man. I’m hoping to put them on this weekend. My next step is prolly gonna be a cam.
No problem, nice can go wrong with a cam on these trucks.
what kinda cam you got man?
Texasspeed stage 2 cam 👍
No check engine lights this replace the catalytic.?
Yes you would have a check engine light with these.
where does the 4th o2 sensor go??
There are no provisions for the rear o2 sensors, the rear ones are not needed for long to headers. They’re for the cats
Perfect look man! Congrats.
What wheel/tire combo are you running? I have an 06 crew cab
Appreciate it brotha! on the rear its on 17x10 rim with 305/45/17 tire and the front is a 20x9.5 rim with a 245/40/20 tire although i recently switched to a 255/45/20 tire for a meatier look
@@ErikRose_ and weld wheels or RaceStar
@@gearjonny369 welds !
I had shorty headers on my cammed 5.3 cateye just like that and 😮💨 it sounded so good man like a vette growl
headers will do it ! 😮💨
Your crossmember is stock or did u get that modified to fit
nah mine is the original one !
Nice video bro I’m installing a 5.3 in my 2000 Chevy Silverado pickup short bed we’re do I find that exhaust set up bro pl help
it was made custom bro by me and my brother !
Is the black coating holding up? These seem like the best bang for the buck mod on these trucks
The black coating is not the best, if you do get them I recommend the stainless one.
@ErikRose_ Thanks, definitely going stainless, and might try to coat myself
No problem, yeah you’re better off coating them yourself.
Hello can you tell me what year your truck is
its a 2000 bro
@@ErikRose_ thank you
hey bro nice truck , is 2wd or 4x4 ?? I bought one just like yours, mine is 2wd
Thanks man, it’s a 2wd drive as well . Nice, these are fun trucks enjoy.
Que convertidor traes en la transmisión? Te va quedando chingona
Gracias mi amigo, es el convertidor original..
How you make it pop??
Mine is tuned on e85 im sure the tune helps with it! 🔥
What’s your muffler setup?
What’s the part number to those mufflers bro? Sounds killer 🔥
muffler im using is a flowfx from flowmaster !
Did you have to move the brake lines and transmission lines or naw
no sir ! just the heat shield on the driver is all!
Why do you prefer the stock airbox intake ? Genuinely curious?
We don’t, we just kept it because we are boosting it so we didn’t want to invest in an intake we wouldn’t need later on.
Yeah the stock header def choking the exhaust but so are those “love taps” you put in the brand new header 😂
it was just on one pipe so wasnt toooo bad kinda 😂😂
@@ErikRose_ oh okay not too bad then 😂😂
No… most cars require some header banging to get them in it doesn’t really hurt anything unless your severely hitting it with a sledgehammer
Has actually been proven to help power in some scenarios but obviously its always better if you can avoid it
new here what are the specs of cam??
Heres the part number with the specs bro.
Camshaft Part: 25-TSP212218R6112
Dose all 4 o2 sensors hook up the headers or just 2 and if just 2 where dose the other two go
Just the front 2 the other 2 get deleted, you will have a check engine light so it would need to be tuned out or there’s others ways of doing it to.
In your video you said something about misfire. Would these headers cause that or check engine light to come on just wondering before I buy them for my truck
Nah the misfire was for something else, these headers will be fine but you will get a check engine for your cats because these obviously dont have any cats but not a big deal if you dont care👌
Putting a muffler would quiet it down some but still put out the horse power
What does the o2 sensor do for the headers since they have no cats ...you'll still get a check engine light right?🤔
@@eddievazquez2330engine needs an o2 sensor to measure AFR to make sure it's not lean or rich. The o2 you see in the header is the pre-cat o2 sensor.
@@sethtodd410 okay cool man thanks 😎
What brand header you use? I missed it
Flashark headers, should have a link in the description ⬇️
What engine bay cover do you have
its from a 6.0 vortec!
what wheels are those? and what sizes on each brother?
Weld Venturas bro! front is a 20x9.5 rim on a 255/45/20 tire and rear is a 17x10 rim on a 305/45/17 tire
Are these Ca smog legal?
not at all lol they delete the cats
Im also supercharged with the magnuson and i put shorty headers but i like the way yours sound better with the long tubes im probably losing hp right?
Yeah long tube headers have been known to be better overall than shorty headers. Long tube headers definitely make more power than shortys!
Low end you’re not for not long tubes they lack the power the power in the on the low end unlike the short tubes but then long tubes on top end gain power
@@SpookyMontero Long tubes are the way to go shortys wont make any more low endtq
Disconnect the battery before you even begin anything.. your computer will do a little soft relearn and comprehend better with the AFR, you still need a tune but it’s better than just cranking it on and relearning while your driving without disconnecting the battery beforehand.
Good info appreciate it bro! 👌
Why does he keep saying we when the other guy was doing all the work and he was holding the camera? With the exception of when he wanted to show a part then the other guy was holding the camera?
Sounds a lot better
Awesome 👏 👍 from 956 South Texas
Thanks 👍
Would these fit on a 4x4 99 single cab Silverado? I’m really interested in buying these if they fit with no problems
I don’t think they do fit with 4x4, I think there’s issues with the fitment.
What is the size are the headers? 1 7/8 or 1 3/4?
these are 1 3/4 bro !
@@ErikRose_ do they have 1 7/8 long tubes
can someone pls tell me what year this truck is!?!?!
its a 2000 lol cateye swap
How you do your exhaust bezel out front of back tire?
Cutting and fabricating. We made it ourselves but you can buy bezels and just cut it out and weld the tip of your choice. Or if you don’t have the tools I’m sure some muffler shop can do it for you.
Are these smog legal in CA?
all long tubes are illegal in california unless it’s smog exempt
Yo what’s the part number for the headers?
Speed engineering 1 7/8 header long tubes I on my 00 suburban no love taps needed. Didn't even take out the spark plugs surprisingly
But love taps add a little power 🤣🤣
I need those wheels!
Nothing wrong with a few taps 😂 doesnt affect performance at all.
Weld Venturas brotha they are 🔥🔥🔥
@@ErikRose_ Ive had so many love taps hella maybe some love smacks🤣 on my rides lol.
I think even road kill had a set of beat headers that made more power lol.
Thanks bro! Imma see if I can get those wheels in 22s I want them
Did you do any videos? I don't see the headers on their site anymore
Would they fit a 07-14 tahoe?
dont think so I believe those are different bro!
Fs fs. They're gonna throw a check engine light right? Accidentally ordered these and seeing if one of my buddies wants them
@@cb8433 ahh damn fr! but yeah they’ll throw a light for the cats but not a big deal! 👌
what size are the headers 1.3/4 or 1.7/8??
What muffler do you have?
flowfx! 🔥
are these painted or powder coated? their website doesn’t specify.
Painted I’d recommend getting the none painted one I think stainless not sure need to check.
I noticed your trans crossmember was modified and don’t have that bigo chunk in the bottom it sits flush with the frame y’all did that or bought it like that ? Only asked cause they do that when they hella low and don’t wanna bend the oem crossmember.
Nah man it’s stock, we didn’t modify it and the truck was lifted before so there would be no need to modify it. At least it looks stock 🤷🏻♂️
Change those out for ceramic coated ones my boy. The painted rust real bad
Great video. From a 1-10 scale how difficult is it to DIY this type of job myself? I have little knowledge of mechanics . I have a 2012 silverado 5.3
If you have all the right tools its not too bad id say its a 5, basically just unbolting the old ones and bolting on the new 👌
Makes me want to do this to my 5.3l but I live in Cali. And my city love to pull people over for loud exhaust, smh.
Yeah that sucks bro, we always gotta be on the lookout 👀.
Truck is beautiful