I have the 1720 but thought I'd post here as there's not many comments I can find for the 1720. Either the Engraver or Engrave Master software is causing all kinds of grief. Some projects I have done work out ok, but there always seems to be a glitch. I would never trust this engraver to go directly to a project without testing the entire burn prior to engraving on the actual item. Even then I'm wary as I've had the engraver stop in the middle and had to re-sand to get the surface prepped again. Project loads ok into the Engrave Master software, adjust all settings as described and test size, start burning and then part way through the laser just stops. Software does not install like normal apps as it doesn't show up in the app's section of control panel. Reinstalled, but not sure if it's even reinstalling cause you can't uninstall first. I've used engravers many times before at work and this should be dead simple and the machine is making it a nightmare to work with. Not sure if it's the software or or laser that's the problem. The key is it starts to burn and then just stops....Unless this can be fixed I cannot in good faith recommend this unit to anyone or provide a positive review, since the machine is only a few months old and has probably done less than 15 small jobs.
Hola soy de Uruguay, tengo una maquina Bachin de 500mw quisiera saber si a esa misma le puedo cambiar el laser a uno de 2500mw si la placa asepta ese cambio desde ya muchas gracias Hello, I'm from Uruguay, I have a 500mw Bachin machine, I would like to know if I can change the laser to a 2500mw machine if the plate accepts that change in advance, thank you very much
Where can i ask for help? I assembled my laser but sadly, it doesnt move backwards in Y axis. I have no problem with moving it manually with my hands, forward and backwards - but itself it only moves in one direction like its stuck. Any ideas or maybe a place where can i ask?
Hola amigo,estoy esperando a que me llegue mi maquina,gracias por compartir. Una pregunta como puedo cambiar el idioma al español?. Ya que edito el txt y lo reemplazo y no me cambia. Un saludo
My frame is not level when adding the feet at 12:42. Its about 1/8th inch off. Can I balance it out with something underneath as long as the overall unit is level? Any other suggestions?
You can put a sponge or other thin object on the foot of the machine. Please refer to the pictures on our website:bachinmaker.com/wiki/doku.php?id=bachin_d8-4050p
I had the same problem as we were setting it up yesterday. With two sets of hands pushing down hard on all the corners at the same time, we leveled it out :)
Thanks Allen this helped a lot
Bro..
Can I get this acrylic part drawing or measurement
Thanks! Arrived broken!
I have the 1720 but thought I'd post here as there's not many comments I can find for the 1720. Either the Engraver or Engrave Master software is causing all kinds of grief. Some projects I have done work out ok, but there always seems to be a glitch. I would never trust this engraver to go directly to a project without testing the entire burn prior to engraving on the actual item. Even then I'm wary as I've had the engraver stop in the middle and had to re-sand to get the surface prepped again. Project loads ok into the Engrave Master software, adjust all settings as described and test size, start burning and then part way through the laser just stops. Software does not install like normal apps as it doesn't show up in the app's section of control panel. Reinstalled, but not sure if it's even reinstalling cause you can't uninstall first. I've used engravers many times before at work and this should be dead simple and the machine is making it a nightmare to work with. Not sure if it's the software or or laser that's the problem. The key is it starts to burn and then just stops....Unless this can be fixed I cannot in good faith recommend this unit to anyone or provide a positive review, since the machine is only a few months old and has probably done less than 15 small jobs.
can the laser be up graded to a 2500mw laser
great video, wouldn't have done it without this!
I want to buy this system, but I want to have a larger working area. Can I get longer extrusions?
I've been asking myself the same question: Did you ever get an answer?
No response. Went through alibaba
buenas, tengo la bachin 4050 2500mw deseo comprar un laser de 40w debo cambiar la placa o esta misma sirve gracias.
Buenas tardes, tengo mi grabador con un laser de 500mw, puede cortar durolac de 3mm o necesito un laser mas potente?
Gracias por el video
Hola soy de Uruguay, tengo una maquina Bachin de 500mw quisiera saber si a esa misma le puedo cambiar el laser a uno de 2500mw si la placa asepta ese cambio desde ya muchas gracias
Hello, I'm from Uruguay, I have a 500mw Bachin machine, I would like to know if I can change the laser to a 2500mw machine if the plate accepts that change in advance, thank you very much
yes ,2500mW is ok ,no need to change the control board. and the 2500m
link is :www.alibaba.com/product-detail/BACHINMAKER-good-quality-2500mW-450nm-blue_62233399642.html?spm=a2747.manage.0.0.4f5771d28AqdT1
Can you engrave on anything bigger than 200mm?
Where can i ask for help? I assembled my laser but sadly, it doesnt move backwards in Y axis. I have no problem with moving it manually with my hands, forward and backwards - but itself it only moves in one direction like its stuck. Any ideas or maybe a place where can i ask?
take a video and sent to :Yvon_gong@hotmail.com
I have this system, but either the board or the power supply is messed up. any idea where replacements can be orderd?
i hope this board will help you:www.alibaba.com/product-detail/BACHIN-D8-B2-0-hot-sell_62212785811.html?spm=a2747.manage.0.0.272c71d2ERNzoK
So the big nagging question - how to keep the wiring off the bed and out of the way. Anybody?
Really should be slower with a step by step instead of this music.
Thanks for your Feedback。
Hi guys.
The laser won't move on the Y axe.X working.
Any ideas?
Need to test whether it is the problem of the motor or the problem of the motor driver, swap the X/Y plug on the control board to see which axis work
el laser no responde a las órdenes del software, ¿por qué puede ser?
Hola amigo,estoy esperando a que me llegue mi maquina,gracias por compartir.
Una pregunta como puedo cambiar el idioma al español?.
Ya que edito el txt y lo reemplazo y no me cambia.
Un saludo
Estimado cliente, nuestro software actualmente no es español, solo inglés. Muchas gracias por tu pregunta.
My laser won’t burn. I can see the Laser On (Strong) but the Laser On (Weak) is not visible. Can you help me?
please send a video to the address: :support@bachinmaker.com
thank you very much.
How can I contact bachin? My laser has stopped running
Dear friend ,there have a manual ,you can see the email address
I want to buy this system in India, please help me
this is the link:www.alibaba.com/product-detail/BACHIN4050-good-price-2500mW-advanced-toys_62162530395.html?spm=a2747.manage.0.0.4f5771d2oXmjx4
www.alibaba.com/product-detail/BACHINMAKER-new-product-mini-laser-engraving_62420736081.html?spm=a2747.manage.0.0.4f5771d2iij66n
My frame is not level when adding the feet at 12:42. Its about 1/8th inch off. Can I balance it out with something underneath as long as the overall unit is level? Any other suggestions?
You can put a sponge or other thin object on the foot of the machine. Please refer to the pictures on our website:bachinmaker.com/wiki/doku.php?id=bachin_d8-4050p
I had the same problem as we were setting it up yesterday. With two sets of hands pushing down hard on all the corners at the same time, we leveled it out :)
@@leeann6117 awesome!:)
Para corte de MDF máximo de 3 milimetros, de cuanta potencia debería de comprar el laser? 300, 500, 2500 o 5500 MW?
5500mw
download the software from : bachinmaker.com/wiki
Nice background songs, but they don't support what you are trying to demonstrate ?
?????Don't support what?