Nissan Titan Fuel Pump Assembly Replacement (tips and Tricks)

Поділитися
Вставка
  • Опубліковано 3 гру 2024

КОМЕНТАРІ • 121

  • @jeffhancock6538
    @jeffhancock6538 Рік тому +7

    Followed the steps in your video and the whole process went smoothly!! Thanks Aaron

  • @stevelasalle5976
    @stevelasalle5976 4 роки тому +10

    dude i appreciate the time you take to film these

  • @zacharyrainwater750
    @zacharyrainwater750 6 місяців тому

    I just bought an 05 that has this issue that I will need to fix before I can get it running, and of all 3 videos I've watched yours was the best on what I'm getting myself into with this. Much appreciated!

  • @Cdiddy150
    @Cdiddy150 Рік тому +2

    Just watched your video and did this repair. It’s totally doable for one person. The only thing I would recommend is to make sure you have a right angle or circle pick to release the clips on the evap line and especially the fuel line.

    • @nativewarrior5052
      @nativewarrior5052 Рік тому +3

      How do I release the fuel line on the pump on top of the tank? I can't figure it out

    • @poolmonkey7479
      @poolmonkey7479 Рік тому +2

      Pinch the two tabs behind the black connector, the two closest things to the fuel pump that is not fuel pump

    • @dathonlawler81
      @dathonlawler81 6 місяців тому

      Who here is replacing due to rough idle and already replaced every sensor? Not sure if this is what I need to do.

  • @hardset-vi3ze
    @hardset-vi3ze 2 роки тому +8

    I loved the video. I just wish you could have shown how to disconnect some of the fuel lines and electrical connections a little closer. Especially for first timers!!!! I had real problems figuring out how to disconnect them. I'm sure filming it wouldn't have been easy either!!!

  • @lovinhands6074
    @lovinhands6074 Рік тому +1

    Your amazing. Very clear..talked through the whole thing, very clear instructions and helpful tips

  • @travisjackson8724
    @travisjackson8724 4 роки тому +4

    Definitely will help me I thought it was going to be way more difficult.

  • @dwightbridges4089
    @dwightbridges4089 3 роки тому

    Man I've been racking my brain out trying to figure out how to do this fuel pump you are the man thank you so very much my baby is running like a dream your a God send THANK YOU THANK YOU THANK YOU GOD BLESS YOU KEEP UP THE GOOD WORK.

  • @DavidNaritaYT
    @DavidNaritaYT 9 місяців тому +1

    Why was the service engine soon light on? Evap canister?

  • @joecarbajal7132
    @joecarbajal7132 Рік тому

    Thank you brother! u saved me time and headaches! u got your self another loyal follower!

  • @OrionGarcia
    @OrionGarcia 4 роки тому +2

    Im getting all the repairs done during quarantine so thanks for posting these 🥳🥳

  • @dcbqb19
    @dcbqb19 3 роки тому +1

    I had to do this on my 08 Pro-4X and the gas gauge now doesn't read the fuel properly so I've ran out of gas several times. Also now have a P045 code that comes and goes but looks like you showed where to look so thank you. Hopefully fixing that code will help the gauge work properly again too

  • @bhardwaajmohabir9147
    @bhardwaajmohabir9147 2 роки тому

    Very nice thank you for showing it on you tube have a good night 😉

  • @SkyNet-ty1tm
    @SkyNet-ty1tm 3 роки тому

    You ARE the Titan GURU 👍👍👍🙏

  • @mikehupp9197
    @mikehupp9197 2 роки тому

    Great video 👍👍👍 Why when I was laying on my back for 2 hours it wasnt as easy as you made it seem 😂🤣😂

  • @rico8089
    @rico8089 4 роки тому +1

    Great video I hope mine goes that smooth. Thanks

  • @michaelmontgomery5326
    @michaelmontgomery5326 2 роки тому +1

    great video just one thing that was an obvious issue, once you got the tank on the ground you mentioned one of three bolts were missing on the deflector plate, one more fell out and when you put it back now it only has one bolt instead of three

  • @jaygarcia3011
    @jaygarcia3011 3 роки тому +1

    Gracias por ese video me ayudo mucho

  • @michaellara8539
    @michaellara8539 5 місяців тому

    This has the most info

  • @stevekurtenbach1951
    @stevekurtenbach1951 2 роки тому

    I really enjoyed the video. You really help

  • @Trapstar66283
    @Trapstar66283 4 роки тому

    Thank you made my day much smoother

  • @doggoneitu
    @doggoneitu 4 роки тому +1

    Great video as always. Thanks

  • @hennessygaming3051
    @hennessygaming3051 3 роки тому +12

    Why do these projects always have one step that should be really simple and end up being ridiculously stupid and take hours instead of minutes? I cant remove the hose from the evap canister fpr the life of me!! You simply said pinch and pull its not that easy. Any advice? I hate when something so minimal stops my whole progression

    • @hennessygaming3051
      @hennessygaming3051 3 роки тому +2

      Can barely get my dam hands in there and i have small hands not sure how you did it

    • @hardset-vi3ze
      @hardset-vi3ze 2 роки тому +2

      That's exactly my main concern too. I had to remove my bed!!! Took 3 HALF DAYS TO COMPLETE!!!

    • @392.menace
      @392.menace 2 роки тому +1

      Having that problem now. Did you find out how to get that line off? A reply would be much appreciated

    • @texasmadefisherman5133
      @texasmadefisherman5133 Рік тому

      Use pliers open the teeth bite down the sides lightly and with right hand pull it out 😊

    • @adams13f
      @adams13f 8 місяців тому

      Sometimes on fuel pumps you may have to pinch and push in on the hose/clip I know thats sounds crazy but check the manual.

  • @bluheat007
    @bluheat007 4 роки тому +2

    I need this video. Thanks

  • @brantthompson199
    @brantthompson199 3 роки тому

    Great video. When I need to do this I will use this video. Good job. Thanks

  • @richardirizarry6460
    @richardirizarry6460 2 роки тому

    Best video. Thank you.

  • @rlauniussimmons5356
    @rlauniussimmons5356 3 роки тому

    GREAT JOB AARON THANKS 😊

  • @elvisrickey4625
    @elvisrickey4625 2 роки тому +2

    Great video Aaron, thanks. Do you think I could cut out part of the bed to get to it? It's an old truck and I'm not really worried about the bed.

    • @BobLarson-bu8zg
      @BobLarson-bu8zg 5 місяців тому

      I was thinking the same thing....... cut a hole and then patch it in with the piece I cut out....

  • @davidsayre7728
    @davidsayre7728 3 роки тому +1

    Thank you sir. Good video 📹 👍

  • @David-rh5bo
    @David-rh5bo 3 роки тому

    Thanks for making this.

  • @joshoconnor6684
    @joshoconnor6684 3 роки тому +2

    4:40 dude why u just breeze over thr fuel line. I got no idea what thr trick to that tab is and mine seems a lot harder to access.

  • @TheRelentless817
    @TheRelentless817 4 роки тому

    Another great video. You make it look so easy...

  • @benmelloncalfs343
    @benmelloncalfs343 3 роки тому

    Holy hell this was an awesome video. Thank you!

  • @johnlundquist4846
    @johnlundquist4846 4 роки тому +5

    Great job! you saved me so much time! so clear and detailed video!

  • @syedhussain3810
    @syedhussain3810 3 роки тому

    very well described video thanks for your time man.

  • @HorizonMain
    @HorizonMain 4 роки тому

    bless. love this guy

  • @4door_vette04
    @4door_vette04 3 роки тому

    Has anyone ever ran a aftermarket fuel cell on a Titan? I’m looking at a fuel cell but I’m clueless on how to go abouts hooking lines up and what lines do what… but awesome video on removal!

  • @rubenespinosa3808
    @rubenespinosa3808 3 роки тому

    Thank you for your video.

  • @eduardocalvillo5658
    @eduardocalvillo5658 Рік тому

    Question for anyone, any chance the filter from this pump itself can be causing startling once you come up on a complete stop then going? Thanks 13:12

  • @handymandivisionllc530
    @handymandivisionllc530 4 роки тому

    Thxs for the assistance !

  • @Cl-1993
    @Cl-1993 3 роки тому +1

    Isnt it easier to lift the front end of the bed up?

  • @coreyf311
    @coreyf311 3 роки тому +1

    Great video! I think you forgot to bolt down the cover plate though when you put everything back together! :)

  • @DarrelllCampbelll
    @DarrelllCampbelll 4 місяці тому

    Thanks

  • @Getagrippeople2witnesses
    @Getagrippeople2witnesses Рік тому

    Any videos on gas tank clogs, gas is going threw the EVAP hose to canister when fueling is there a vacuum Fault stuck open under the hood.

  • @arthurward6871
    @arthurward6871 4 роки тому +7

    I have a 2004 Pathfinder Armada and the fuel pump is under the drivers side passenger seat! It was too easy! Didn’t have to drop tank. Small cut in the carpet that can easily be hidden cause it’s under the seat!

    • @AaronHinesAuto
      @AaronHinesAuto  4 роки тому +3

      Wow! Good to know. I bet that saved u some time

    • @kanaotysuri532
      @kanaotysuri532 3 роки тому +2

      Bro I have a 2005 Armada and I did the same exact thing, entire job took me 20 minutes!

  • @DC5_Dusty
    @DC5_Dusty 4 роки тому +1

    I got everything except the main fuel line off the tank im having trouble removing it. Can someone explain how to do it?

  • @boashna
    @boashna 2 роки тому

    chriss fix it is scared .. lol good video

  • @Phoenixrising8313
    @Phoenixrising8313 2 роки тому

    How did you disconnect the furl line at the filter also the evaporate? Thank you?

  • @kennethpeterson5610
    @kennethpeterson5610 8 місяців тому

    I had the Nissan dealer replace my fuel pump about a year ago. The fuel gauge is not working correctly. The gauge indicates a 1/4 tank but the tank is empty. Next, the gauge will show a 1/4 tank, then move up to just under a 1/2 tank, then go down below a 1/4 tank. This happens while driving or when parked and returning to the truck a few minutes later. I complained to the dealer, and they said there was a problem with my instrument cluster. However, everything seems to be working correctly with the cluster. Is it possible that they damaged the float, or is the float defective? Any advice. 2008 Nissan Titan SE model 167,000 miles.

  • @MikeGarcia-x4g
    @MikeGarcia-x4g 3 місяці тому

    Replaced the fuel pump on my 04 Titan and did every step by step as the video but can not turn over the truck! Checked the fuses and fuel lines to see if they were connected and they are. Even put on a new crank sensor but nothing!! It cranks but just won’t turn on. Why would that be? What else can I check?

  • @CrossWindOutdoors
    @CrossWindOutdoors 2 роки тому

    I'm stuck on the hose at the evap canister. I can't get the thing off. How did ya'll do it?

  • @livingsimpl3
    @livingsimpl3 Рік тому

    Is the fuel pump still running? Where did you buy the part

  • @addictedoutdoors1895
    @addictedoutdoors1895 3 роки тому +1

    I have a 2006 nissian titan. DOES IT HAVE A FUEL FILTER OR NOT OR IS IT PART OF THE FUEL PUMP ASSEMBLY?

  • @nathanielslaughter137
    @nathanielslaughter137 8 місяців тому

    So after looking at the fuel pump for the flex fuel option, it says it doesn't fit my vehicle after putting in my vehicle info. Any ideas?

  • @mattbosch8893
    @mattbosch8893 5 місяців тому

    Can’t even get my pump fuel line off like you did I have to depress bored sides at same time but the stupid pump shield is in the way

  • @PhillyDee215
    @PhillyDee215 4 роки тому

    Great video as always💯

  • @menjivar76
    @menjivar76 3 роки тому

    Excellent video, thanks for posting it, just one question, I see the check engine light on, is that because you change the pump or it was like that before?
    I have a 04 Titan and my check engine light is on, I put a scanner and gives me a P0463 code witch is Fuel Level Sensor, my fuel gage is up and down all the time, I can fill the tank today and tomorrow will show empty. I can pass my smog check test. Thanks a lot for this video, it’s gonna help me a lot.

  • @yungavalor3192
    @yungavalor3192 2 роки тому

    Help! My fuel feed hose is stubborn. It won't budge. What should I do?

  • @betocastaneda1597
    @betocastaneda1597 4 роки тому

    Good morning, the yellow filter that can be removed just below to put on the new pomp that I have since mine does not bring it?

  • @420520max
    @420520max 8 місяців тому

    What fuse do i pull for a 2012 pro4x

  • @ramoncamus8093
    @ramoncamus8093 4 роки тому

    I have a 2012 Titan and I'm having a fuel supply problem. I could hear the pump running for a few seconds when I turn the key on in the morning but my engine won't start. When I spray starting fluid on the intake the engine runs for a few seconds. What is the fuel pressure psi on a good fuel pump. Planning to do this test first before I replace the fuel pump. Thank you in advance and very helpful video.

    • @michaeltsosie9560
      @michaeltsosie9560 3 роки тому +1

      I had this problem a few weeks back it would start up when starter fluid was used and just shut off when it was put into gear. So I looked it up here on the trusty youtube and found out it was my crankshaft position sensor that gave out. It is located under the truck right at the bell housing. Replacement part coat me 32 bucks and less than fifteen minutes to change out. Trick was undoing the connection. Have to push the green tabe down and towards the bell housing and pull at the same time. Started up no problem when replaced. Now I have to change the fuel pump due to power or even going above 2500 rpms.

    • @kaipos8601
      @kaipos8601 Рік тому

      I think 58psi

  • @stevericci3308
    @stevericci3308 4 роки тому

    Is that an aftermarket pump assembly and if so is all ok

  • @aprilbarber3834
    @aprilbarber3834 27 днів тому

    How do you check the fuel pressure?

  • @carlosamorales646
    @carlosamorales646 3 роки тому

    Good video

  • @rico8089
    @rico8089 4 роки тому

    Different fuel pump 2004-2007 and 2007-2015 ? 2007 uses which one

  • @staypuft199
    @staypuft199 2 роки тому

    I did everything like the video complete with right part. Has difficulty starting and gas gauge reads wrong....someone please help me because i dont kno wat to do

  • @dennismudd3494
    @dennismudd3494 3 роки тому

    How's it going? thanks for the video. I got a 08 titan, I start it and once started it basically dies out. But during that moment if you push on the gas pedal it doesn't Rev up at all.. I'm going to check the power to the fuse like you showed.. I also tried to use a code reader but didn't get a code

    • @joemoremoney
      @joemoremoney 3 роки тому

      Did you figure out what was wrong? Having the same issue right now

  • @jacobash1818
    @jacobash1818 3 роки тому

    What’s the difference between a 07 and an 08 fuel pump no flex fuel

  • @210GrainsOfJustice
    @210GrainsOfJustice 2 роки тому

    👏🏻

  • @augusthirn7803
    @augusthirn7803 Рік тому

    It would be nice, if you could see how the fuel and power lines connections are disconnectet.

  • @Lionheart_88
    @Lionheart_88 3 роки тому

    I cant get the evape line off, been struggling with it for over an hr now, i feel like im going to brake it

  • @dennisparson103
    @dennisparson103 3 роки тому

    Great video but can you please tell me where the fuel filter is located.

    • @SF80CAMARO
      @SF80CAMARO 3 роки тому +2

      The small mesh basket on the bottom of the fuel pump is the filter. There is no external filter too replace.

  • @TheJu2ber
    @TheJu2ber 3 роки тому

    Hi Aaron, the fuel pump you listed for 2005 Nissan Titan (non-flex) is the same fuel pump as flex fuel titans. Can you confirm Delphi (DFP FG1277) is the correct pump for 2005 Nissan Titan (non-flex)? Thank You.

  • @josueespinosa1445
    @josueespinosa1445 2 роки тому

    Will changing the pump give me better milage per gallon mines is giving me 210 miles a tank on the city (2004 titan)

    • @kaipos8601
      @kaipos8601 Рік тому

      No. That sounds close to right in stop and go

  • @vic9145
    @vic9145 3 роки тому

    What did you hook that power drill to? It was a bad angle I couldn't see also can u do a video on replacing the fuel filter for 07 model?

    • @poolmonkey7479
      @poolmonkey7479 Рік тому

      Filter is in the tank, part of the pump assembly

  • @djritm3215
    @djritm3215 4 роки тому +1

    Thanks again your vids are informative and helpful . What was the service engine soon light for? The gas cap maybe?

  • @WD-ti5cn
    @WD-ti5cn 2 роки тому

    Can you pull the fuel pump and just replace the motor or do you have to buy the whole unit?

    • @kaipos8601
      @kaipos8601 Рік тому

      You can just replace the pump in the assembly

  • @parker6334
    @parker6334 2 місяці тому +1

    Thanks for not showing how any of the clips come on or off its really important not to know

  • @jasonbarto8406
    @jasonbarto8406 4 роки тому

    I have a 2012 titan and now it spots fuel back at me while pimping gas...please tell me u know what it is so I can fix it...thank u inadvance

    • @kanaotysuri532
      @kanaotysuri532 3 роки тому

      Common problem with Armadas, I have a 2005 and it did the same thing until I fixed it. The purge valve (vent control valve) is clogged from debris and it is blocking proper vent flow of fuel vapors to the evap canister while pumping gas. Dealerships will charge $600 to replace and fix it, but I found the part on Amazon and the fix was only 15 minutes of my time.....
      You have to change the EVAP VENT CONTROL VALVE (purge valve) which is located just under the fuel door, and you have to remove the rear driver side tire to access it. Here is the link I used:
      ua-cam.com/video/C3ykQbG0T2s/v-deo.html
      Here's the part:
      www.amazon.com/dp/B00BV6VRHC/ref=cm_sw_r_cp_apa_fabc_M73BQFJ4RXRBRSKKM5MY

  • @johnbutler8689
    @johnbutler8689 3 роки тому

    Why won’t my tank go back up doming wrong ? I’m going crazy please help j butler

  • @wtmpoppasmurf
    @wtmpoppasmurf 3 роки тому

    i have an issue with my 04 titan 2wd. sometimes when Im driving and i hit the gas, the rpms go up but the truck will not speed up. could this be a bad fuel pump? any help would be appreciated. thanks!

    • @celticslimjim
      @celticslimjim 2 роки тому +1

      If it's doing what u describe from an idle, like at a red light, then it might be your transmission is failing

  • @dallaspayne5009
    @dallaspayne5009 2 роки тому

    Bro I’ve been beating the line at the Evan canister. I cannot get it off

  • @Drewsoloking
    @Drewsoloking Рік тому

    I changed mine now my fuel gauge doesn't work help

  • @venturetimeoverland3848
    @venturetimeoverland3848 Рік тому

    I'm stuck halfway through the job! I cannot get my hands in there to remove the electrical connector and fuel line off sending unit. I have small ladies hands and still cannot! There is absolutely no room! And no I cannot get a connector puller or long needle nose pliers on it safely. 😤

  • @chrisfelter9897
    @chrisfelter9897 2 роки тому

    👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿👍🏿

  • @7CAJONEZ
    @7CAJONEZ 3 роки тому

    Or put a universal pump on the outside and sell it.

  • @jtomtl
    @jtomtl 3 роки тому

    Service engine soon…. Omg Nissan come on!

  • @rowenaroman2887
    @rowenaroman2887 Рік тому

    Hm

  • @germangarcia3298
    @germangarcia3298 4 роки тому

    Aaaaa

  • @xposethatruth1682
    @xposethatruth1682 9 місяців тому

    Or just use the access under the passenger side rear seat

  • @TheRaiderbid
    @TheRaiderbid 4 роки тому

    Great video! Thanks for the tips!