@@madeingarage7040 Very cool project. I am just curious, at time 9:01 the pressure gauge stayed at zero. Was it showing properly or did you changed something in design later to get the mentioned reading?
when bending this profile, the resistance was so small that the pointer only vibrated slightly. However, when bending the flat bar, the pressure gauge indicated 100 bar.
Found you by the pipe bender video! I like your DIY hydraulic power pack very much. I have made my own from 24v tail truck lift hydraulic pump and a 24v siemens SITOP 40 amp power supply. I have used it 5 days a week every week to drive a stamping press.
Really amazing work and great skills that you have. So novel to use a hydraulic steering pump from a car, would have never thought this would work! I also watched your pipe bender video, another amazing job! Wow!
Witam. Bardzo fajnie od pomysłu do wykonania ! Zresztą jak wszystkie Twoje prace ! Mam pytanie bo jakbyś czytał mi w myślach - od miesięcy myślę nad przróbką mojej prasy z ręcznej pompy na mechaniczną . Chodzi mi głównie o wyeliminiwanie uciążliwego martwego skoku siłownika i wolnego także jego powrotu. Pytanie 1 - czy ta pompa wytworzy wystarczające ciśnienie abym uzyskał na siłowniku co najmniej te 20 t nacisku ? Pytanie 2- w jaki sposób nożna by wykonać spowolnienie pompowania podczas nacisku roboczego bo na filmie wydaje mi się że tłok posuwa się trochę za szybko. Robimy ciągniki i wszelki sprzęt rolniczy , najczęściej w prasie w rękach trzeba trzymać spory gabaryt więc lepiej żeby zjawisko nie przebiegało aż tak gwałtownie :)
Nacisk zależy od ciśnienia i od średnicy tłoka w siłowniku. Mi ta pompa wytwarza ponad 100bar. A prędkość możesz ograniczyć przez nacisk drążka lub zastosować regulator przepływu oleju.
Great job! Do you know flow rate of that pump and how much electricity drains from battery? I made air compresor for garage from freezer compersor.. its 30W compresor, can make 10bar preasure and need 1.5h to fill 100L tank.. I mean is possible for garrage use but have downsides. Whats downsides of that system? Tnx
No pressure relief bypass?... every hydraulic system needs a way to bypass excess pressure to tank for the safety of the system & the operator... you should be able to add one in the plumbing easily enough.
Great job!
What's the maximum pressure?
Thank you!
While bending this flat bar, the pressure gauge showed 100 bar. I think the maximum of this pump is 150bar.
@@madeingarage7040 Very cool project. I am just curious, at time 9:01 the pressure gauge stayed at zero. Was it showing properly or did you changed something in design later to get the mentioned reading?
when bending this profile, the resistance was so small that the pointer only vibrated slightly. However, when bending the flat bar, the pressure gauge indicated 100 bar.
@@madeingarage7040 Thats what I tought. Very nice!
@@madeingarage7040 Thats a great idea. Whats the pressure when you are at the end of the piston stroke?
Found you by the pipe bender video! I like your DIY hydraulic power pack very much. I have made my own from 24v tail truck lift hydraulic pump and a 24v siemens SITOP 40 amp power supply. I have used it 5 days a week every week to drive a stamping press.
Great. Regards
Really amazing work and great skills that you have. So novel to use a hydraulic steering pump from a car, would have never thought this would work! I also watched your pipe bender video, another amazing job! Wow!
Thank you for your kind and motivating words.
Cool project, thanks for sharing.
Thank you
Witam. Bardzo fajnie od pomysłu do wykonania ! Zresztą jak wszystkie Twoje prace ! Mam pytanie bo jakbyś czytał mi w myślach - od miesięcy myślę nad przróbką mojej prasy z ręcznej pompy na mechaniczną . Chodzi mi głównie o wyeliminiwanie uciążliwego martwego skoku siłownika i wolnego także jego powrotu.
Pytanie 1 - czy ta pompa wytworzy wystarczające ciśnienie abym uzyskał na siłowniku co najmniej te 20 t nacisku ?
Pytanie 2- w jaki sposób nożna by wykonać spowolnienie pompowania podczas nacisku roboczego bo na filmie wydaje mi się że tłok posuwa się trochę za szybko. Robimy ciągniki i wszelki sprzęt rolniczy , najczęściej w prasie w rękach trzeba trzymać spory gabaryt więc lepiej żeby zjawisko nie przebiegało aż tak gwałtownie :)
Nacisk zależy od ciśnienia i od średnicy tłoka w siłowniku. Mi ta pompa wytwarza ponad 100bar.
A prędkość możesz ograniczyć przez nacisk drążka lub zastosować regulator przepływu oleju.
So just like what's on any pickup truck snowplow. It's a good repurpose of a used part.
Thank you
An alternative would be a second hand wheelchair lift setup.
Yes😉
firstly what great use of a power steering pump and just one question the smaller wires in the switches , is there an internal relay? great work👍
Thank you. Thin wires are directly soldered to the red and green contactors. They are used to turn on the relay located inside the pump.
@@madeingarage7040 thankyou that's great to know keep up the good work 👍
Thank you!!
Great job!
Do you know flow rate of that pump and how much electricity drains from battery?
I made air compresor for garage from freezer compersor.. its 30W compresor, can make 10bar preasure and need 1.5h to fill 100L tank.. I mean is possible for garrage use but have downsides.
Whats downsides of that system?
Tnx
So far, the only drawback is the battery that discharges.
Nicely done. Now could you convert this to a car lift? Or would it take 2?
You can connect any actuator, even a car one. In the next video I will show you how I did it.
@@madeingarage7040 Thanks. That would be awesome (especially with the current prices of lifts on the market).
I/O boats have such a pump for trim control.
Interesting
Hi great video do you think this would work with a 20volt Dewalt 9.0Ah Li-ion Battery with a
20V to 12V Step Down Converter for doing small jobs
Let me just say that this pump draws 60A at peak times.
Was sind das für exzentrische Verschraubungen vor den Schnellkupplungen ?
Hersteller würde reichen.
Danke 🙏🏽
Hydrolider
Hej.Mógłbyś zrobić listę części, których użyłeś? Chcę zbudować coś takiego .
Wszystko pokazałem w filmie. Sam nie mam listy części poprostu improwizowałem😁
Nice
Thank you
подскажите, он подойдет вместо ручного насоса на гидравлический пресс 30 тонн?
Yes. But in my opinion the pressure will be reduced to 20t.
Класс!!! От чего насос?
Opel Zafira
Po co jest drugi zbiornik oleju
Ponieważ w tym białym jest za mało oleju do zasilania większych siłowników.
No pressure relief bypass?... every hydraulic system needs a way to bypass excess pressure to tank for the safety of the system & the operator... you should be able to add one in the plumbing easily enough.
There is an overflow valve in the distributor.
Прикольно но манометр ничего не показывает и соединение около быстросъёма потекло
Yes. I tightened it more and it no longer leaks.
Calendar lode capacity?
Oil tank capacity?
Try Hydraulic oil rather than gear/engine oil.
I am afraid for the life of the pump
@@madeingarage7040 They are designed to sit in a moving vehicle and run all the time under pretty much same loads, don't see an issue.
I see a leak at 9.25 mark
Yes. I tightened the nut more and it helped.
Please reply
I replied
I spy with my little eye, a log splitter in the making.👁️🪵🪓
Maybe😉
Or a hudralic bearing press? 🙄
140 bar = 8 ton press? 🤔
The pressure depends on the piston diameter and pressure.
Pipe bender 😎
Calendar lode capacity?
I don't understand the question
@@madeingarage7040 Just a guess: "Cylinder load capacity?"
365 days, divided into 12 months.
@sonofadutchman9315 sorry I men3 slender lode capacity
Please reply
I replied