Steve: THIS was an OUTSTANDING beginner video!!! Great photography, focus, audio, clarity of your voice, screen overlays to clearly demonstrate WHERE the controls you were explaining are located. THANK GOD FOR THE PAUSE BUTTON! It was needed, but the information is there for us to repeat, repeat, repeat until we have achieved what you have shown us. THANK YOU! I'm using this video to guide me through my older Jumper T-Lite, since it is much better and absolutely up to date for my Jumper T-Lite. Respectfully, - Jim
Knowing this video is here makes me a whole lot more confident for when i finally make the push out of RTF kits. I'm not sure how someone is supposed to figure all that out without some kind of tutorial to begin with... Alas, too many other things to spend money on for now though (including saving up for my own jeep), so I'll just have to be happy with my little kit for now. At least I'm flying! :)
You can switch the momentary switches into on/off switches in the logical switches page in the menu (page 9 I believe) then no more worries with momentary switch lrobs
Captain I left the props on just like you and now I'm being rushed to the hospital.. 🥶🥶🥶🥶🤺🥶🤺🥶🤺🤫🤫 the drone took off and took 3 out humans before it crashed. Lol. Just playing. Great review buddy.. 💙💙💙💙🥶🥶🥶🥶 Mikey
Going back to the time when I was FPV greenhorn, I would really appreciate this video! Great informations for EXACTLY what all the newbies would need to get started, and then they can add features as they progress... Features of the ExpressLRS module can be fully exploited by changing OpenTX to EdgeTX but that's not a topic for this video. Great job Steve 👍👍👍
I've seen people use them as pairs (i.e., press both at once to set off a command). Other than ON/OFF temporary switches on a quad (lights on, lights off, or some external add on), I'm not sure what I'd use them for.
I did everything correct even added sounds to my channels. But when I save everything in Beta flight . Disconnect , turn off Kwad and Jumper t lite. When I turn it back on . The Model I took forever to create gets deleted back to MODEL # 1 etc.... Like the Controller reboots to factory settings when I turn it off. I tried again and I get the same results. Any idea whats wrong with my set up Capt> ?
You don’t set up sounds or models in Betaflight…. So I see where you’re messing the process up. You set up sounds and models in the radio and there is no SAVE button. When you create a model and give it a name every change you make is saved. BETAFLIGHT CONFIGURATOR is where you configure the FLIGHT CONTROLLER in whichever drone you bought, to react to the switches/buttons on whichever radio you have used to BIND to the receiver (whichever type it may be) that is in the drone.
@@CAPTAINDRONE798 I didnt create sounds in Beta flight. Did it in Jumper T lite page 10 I believe after setting Channels and used the sounds in the SD card built in. Just like in your video. I did everything perfect like in your video. Step by step. Works perfect. Its after all settings are saved in Beta Flight, Disconnect to it, Power off drone and controller where the problem starts. Again, when I turn on controller. The Model I named and created turns back into its original name " Model #1 " Like the Controller reset itself clean with all the work I did :(
@@rhysezfpvif you created something like 100 different models, you then select the one you want. Push in the select button when your on the model page.
very good review. very happy and impressed that this rx has a trainer port. i wish my original t-lite had this so i could use as intended to train my son., he is 4 and uses my t-lite in liftoff and can fly acro but irl is very scary for me to watch and he almost lost his tinyhawk fs2 in about 15seconds lol. thank you for what you do and this is a great channel. p.s. i just realized i wasn't subscribed...i am now.
I’ve never seen anyone use the trainer port option so I’m totally unfamiliar with it. If anyone asks a question about it, feel free to respond. Thank you.
mine still going strong after 2 years mm spray deodorant in the gimbals they stay as new I love plastic hall gimbals ,, and still go to my jumper pro for the best flight experience ,, never lost a signal since owning , I like a light controller
Один з найбільших переваг цього відео - поетапні інструкції. Це допомагає новачкам з легкістю орієнтуватися в складних процесах налаштування. Відео пояснює, як зв'язати дрон з контролером керування, як виконати налаштування пульту дистанційного керування і як встановити додаткові параметри. Додатково, рецензент відзначає хороше пояснення основних функцій та налаштувань Jumper T-PRO дрону. Він розглядає різні аспекти пристрою, включаючи пульт дистанційного керування, передавачі сигналу, мотори, батарею та інші компоненти. Незалежно від рівня вашого досвіду використання дронів, це відео може бути корисним джерелом інформації. Його ясна та зрозуміла презентація допоможе вам в освоєнні Jumper T-PRO та його налаштуванні.
Hello I need help with charging of the transmitter. On its top there is a USB C port where I am suppose to plug a USB C cable and the charging should be on by default. But what's happening - As soon as I connect the charger, The transmitter Power button light and LCD light comes on and goes out within a second. That's it. No indication or display for charging. - I have to keep the transmitter ON and then keep it connected to the USB C charging cable "imagining" that it gets charge only when is ON. But still no charging indication is there. Since the Tx is ON it starts beeping after few minutes. Have to keep stick moving frequently. What is the standard protocol for charging Jumper T pro?
Xm+ sucks! I would never tell anybody to get xm+ due to the close proximity failsafe. You can't arm with your radio too close or fly close to yourself indoors with small ducted whoops. I hate doing benchwork that requires the radio be connected with xm+. Ever had to check motor direction with your toe? I would also say that elrs is super easy too. Not as user friendly as frsky, but not too hard and well worth it when your comparing the performance/price ratio.
@Silvan Pierce I tried and successfully bind the Cetus Pro with Jumper T pro, try to follow the steps in this video, when he presses the original factory bind button you press the bnd inside the menu of Tpro, remember to choose Frsky D8 ua-cam.com/video/24bjbRqQqjw/v-deo.html
In order to bind this to any drone you have to find out what type of receiver is in the drone you are binding to, then select it in the remote. I have no idea what receiver is in the CETUS PRO.... could be a D8 receiver, & if that is the case you could bind it to the Jumper, however, the CETUS PRO is not BETAFLIGHT which means that even if you did bind it, you'd have to use some type of software from BETAFPV to configure what switches do what.
@@CAPTAINDRONE798 I should have said it different. I wasn’t trying to say 25-30 batteries was a lot. I was just trying to refer them as Flashlight batteries and not Vape batteries. Flashlight collector’s usually buy Cells by the case for a much better deal.
It is a nice video, thank you.. I want to ask a question about failsafe... On my jumper t pro (ELRS version with 3 receivers)I couldnt find the failsafe settings menu. It has to be On model setup menu/ Internal RF/ Failsafe .. but It doesnt exist. How can I solve the problem..
@@CAPTAINDRONE798 thanks for your early reply, but it doesnt exist in the menu. there is only internal RF section . I select internal rf crsf and there is not any failsafe option there. :(((
@@CAPTAINDRONE798 on open tx yes it is close the area you said. But on edge tx there is not any menu about failsafe. Especially with internal elrs it doesnt exist :((. I think , I will set it on Inav CLI section.
I have jumper t pro elrs version transmitter but I want this transmetter to control two drone separately but it have 1 reciver and this reciver is not available in market then can i use radiomaster elrs and other elrs reciver connect with jumper t pro does its work ?Will it work? And if I do, which receiver should I use?
Normally NO, only one receive is connected at anyone time so that you don’t accidentally fly your friends drone unexpectedly . However with some receivers (cheap 3rd party ones) they get sloppy and can connect to a signal so more than one is in use
If you're brand new to RC and don't have a transmitter yet, I could see the appeal of this, but man this thing looks cheap. I think RadioMaster is ultimately going to win in this gamepad style matchup.
I think the regular Jumper T Lite made alot of headway and this is going to be a step above especially in a month or so when they install the express elrs as part of the internal source instead of having it be external. It's going to be a game changer I think and I know from my Jumper T Lite that it doesn't feel cheap and I'm sure this one will feel even better. No way will this lose to radiomaster.
I got the built in ELRS version which looks from the images it comes with the usual T antenna, please tell me I don't need to open it and buy another antenna to put in it????
I just tried binding elrs . No bind . So i tried an r9m . The tpro has r9m in the setup but the r9m instructions don't match what the jumper setup says or does . I tried holding the rx button and plugging in the battery and put jumper in bind and press the roller knob and selected 8 ch no telemetry and press the roller knob again and it chirps like an frsky bind noise . But nothing binds .
All is well with your radio. ELRS binding requires that the receiver and radio are on the same firmware. I assume you have an ELRS module attached to the rear of your T-PRO. R9M... never tried it. But binding to receivers other than ELRS is usually much simpler as the firmwares do not need to match. Your must be new at this which can be daunting for beginners.
@@CAPTAINDRONE798 I managed to bind a crossfire rx instead . The tbs crsf micro will bind to a new unused crsf nano without lua script or computers or flashing or firmware upgrades or matching rx's or buying more computer parts to finish making 💤💤😴
I bought the elrs version of this jumper t pro I thought I can bind it to my armor 65 lite that uses bayang protocol but it is not working at all.. I've heard I need to buy a multiprotocol for it, is it true? Is this jumper elrs not multiprotocol already? Please help me understand this...
ELRS is always only ELRS, so if what you are attempting to bind to is not ELRS then it will never bind. You sound very new to the RC hobby which means that even if you purchased the 4-in-1 version you’d still have difficulty binding the radio to your drone. What I mean is that you need to do research on how to setup a model in the radio, as well you need to know what receiver is in your drone & how to bind to it, and then how to use BETAFLIGHT for configuration.
@@CAPTAINDRONE798 Yes you're completely right, I'm new to this hobby. I've heard that I need to install external module to it if I want to control non elrs drone.
Hi, I bought that same pack but I can't get the bars to move in BetaFlight. I have flashed RX and TX with ELRS Companion and when I want to load the files with OpenTX it tells me that it is incompatible. Could you do a tutorial installing the RX in any drone? I have an inoperative drone because I'm waiting to install the RX and get it working....
i have rc car with flysky gt3c radio, can i use the rx and bind to jumper t pro? or do u have any recommendation rx to connect jumper t pro to my rc car? thank you
Depending on the version of receiver (what type of flysky receiver is in your car... is it a unit that has a bind button or can be put into bind mode) it would most likely work because Flysky is one of the most common receivers on the planet and many radios work with it.
Very great video! i just followed the steps and everything was great! i just got a problem: when i check on BF in the "receiver" menu, Roll Pitch Yaw and Throttle are mixed and is a mess. For example: the Throttle stick on the radio makes move the pitch on BF, and the Throttle on BF is actually moved by the Roll stick on the radio...any suggestion on how to solve the problem? many thanks! this has never happened to me before, and both drone (moblite7) and the jumper t pro are new, so i can't understand which one is faulty...
@@CAPTAINDRONE798 I checked your video but it seems that the seller provided me an incorrect item, I can't seems to find any ELRS option in my remote. Ohh! well, might be sending this back.
@@zenargaming1257 Are you sure you watched my video? The answer is right in front of you but you are not pressing the correct button and it may be to complicated for you at this time. I think you need to enlist help from someone in the FPV hobby if you have someone near you. It is a very simple process and eventually you’ll figure it out (everyone in the FPV hobby had to figure it out).
Hey, I bought the controller for my new fpv hobby. First of all I want it to connect with my labtop for the simulator. When I connect it with my labtop with USB c it don't ask me if I want to use it as an controller. I find no options to connect. Can someone help me please. Ian really frustrated and it's so easy for sure. Thank youu
Watch again, it was Horizon, Angle, Acro. Acro means there are no restrictions and that is the default for all FPV drones, so this is why there is no option in Betaflight to select a mode called Acro. When the Modes Horizon and Angle are NOT SELECTED, then it means the drone is in ACRO.
Hi Steve, Thanks for the video's. I'm looking to get into FPV flying. (cinewoops)😎😎 My idea is to start first with the Jumper T-PRO RC to practice on simulators and for later to fly with it. Then, buy the DJI Goggles Integra before buying cinewoop drone with Ocusync 3. Do you think this is a right approach to start?🤔? thanks!
real simple.. are you taking the P? 5 days iv been at it both updated & binded i set buttons & sounds from this vid now i have sintax error on mix ch sa WHEN USING WIZARD THERES NOTHING ON THAT BUTTION
So I am trying to set this up and when it got to putting the sound track on, it said that there were no sounds on the SD. And I went and checked on my computer and it had a while sounds folder. Please if you could help that would be great. Also very nice tutorial so far!
All 4 in 1 and ELRS radios use an OPEN TX or EDGE TX software. That software has to find the sound files in a particular directory. If they are on the micro SD card but in the wrong directory, it can't find them.
Newbie question! This controller will not connect with an ELRS drone without the additional module attached to the back? That seems a little clunky if I'm just looking for an ELRS controller. Thanks!
My biggest complaint about my t lite is the screen,.my old eyes struggled with it. The controller apart from that was great , gone to the eachine tx16s now... This screen doesn't look much bigger than the t lite.
One thing I would of mentioned before purchasing the drone is whether or not the xm is ACCST. It will not work with that radio. I ran into that early on and submitted a question to you which you really didn't provide an answer.
Good point... I forgot about FRSKY and that mess. The good thing is that pretty much all FPV drone companies use the knock off FRSKY XM+ in drones purchased which is not ACCST.
I just bought the jumper t-pro with built-in ELRS... mine already has the latch button on the back the SD card in it and sound already mine says Edge TX when I turn it on. is that different than open TX? I guess for some reason they updated mine and sent it with a memory card..
Good instructions Steve. I have not flown an FPV drone but looking for a contoller to use a simulator to learn what is the best 1 to buy and what simulator program to get.
HI Steve i just receive My t PRo -i Order With ELRS module and receiver but they dont add me the receiver CAN you help me to Choose One GOod REceiver ?? for this Module ? the stock one they say can go up to 5 kmh THAnks Steve !!!!!!!
You can pick pretty much any ELRS receiver. Just make sure that it matches the frequency of your module (2.4 G or 915 MHZ). Then make certain your receiver and module are on the same ELRS firmware, and they will bind.
@@CAPTAINDRONE798 thanks Steve I send you email with module check it if you can it doesn’t power on only when I Insert type c cable in module power on 😭😭.
hello,would it be the same to set-up a drone that does'nt have acro,i know i should be able to set-up for a bugs or mjxq since its in the list of suported protocols,the original controler stoped working so i'm getting a jumper t-pro so i can also get a freestyle quad later on,so the bugs original controller has one momentary button for arm disarm,a momentary button for high and low speed,and a momentary botton for 360 flips but i dont realy care about that one,thank you in advance for your time
@@CAPTAINDRONE798 When you ever have a chance please fly that Traxxas drone the Aton Traxxas it’s super fast very nice drone I would like to see you fly that drone and make a video off of it I will guarantee you people will fall in love with that Drone
Is it the same setup for the internal ELRS controller and binding to a Jumper 2.4ghz ELRS AION-RX-MINI RX? Im new to this hardware. In the old days we had a crystal in the control and receiver lol
@CAPTAIN DRONE I have watched your video and created an arm switch but the problem is that when the switch is down BF sees it as high, than in the middle is sees it as low, and also for the up position. Seems inverted I have set the switch for 2 way in the control settings but it always uses the middle of the switch to change values in BF. I want use it as a 2 way switch, like down is a low value, and up is high value without the middle of the switch changing any value. How can we do that?
So as you say this binds to hobby grade drones but the protocols have hubsan and bugs etc what does that mean? As I associate them with the likes of the bugs 16 pro etc
The list says it binds, but I've never tried it. It is using the same common chip similar to the JUMPER T18 and other multi protocol radios, so you may wish to see if there is a video on youtube with a radio using this chip.
So im confused , should i get the ELRS type without the back ELRS module backpart and still be able to use the 4 in 1 or do i have to buy the 4 in 1 and never update my future drones with ELRS receivers? im confused im a beginner sorry :D
If you get an ELRS controller, then that means you pretty much wish to only fly drones with an ELRS receiver. If you get a 4-in-1 controller, then that means you wish to fly drones with all types of receivers and then have the option of adding the ELRS module.
@@CAPTAINDRONE798 Hey , I followed ur guide to were i can i have elrs one so a little differend. but in the modes i got everything setup like u do but ur arm disables with aux to the left but mine is completly to the right..
Hello, i am planning to buy a flywoo firefly hd fpv. and i dont know witch controller i will buy, somehow the goggles i choose is dji. but i have a tight budget for choosing a controller, can you make a suggestion which one should i buy?! thank you very much
If you need a BIG screen then you want something by RADIOMASTER. If not, then pick anyone and you'll be happy. You just have decide if you want a 4 in 1 chip model or an ELRS model.
@@CAPTAINDRONE798 thanks for your concern, my friend. I’m a newbie in this activity, trying to learn everything. Hopefully soon I’ll be flying my quad. Your videos are amazing. Thanks for sharing with us. A fan from Brazil 🇧🇷
I got a jumper t pro radio, and am trying to bind an frsky rxsr reciever to it's 4 in 1 multi mode, The videos show how to go to multi mode than select "frsky x" which is supposedly the correct mode and select that, but in multi mode on my radio frsky x doesnt show up, WHY COULD THIS BE
Watch my video on how to setup the RADIOMASTER ZORRO and bind to a drone. I bind to the FRSKY RXSR... watch the vid and pay attention to what I select.
Got to " Play Track " after that " no sounds on sd > exit " ? i copied both of the latest SD downloads and both give me the same message . i opened both files on Windows and the files are complete and play the SOUNDS ??? help
It sounds like your .WAV sounds are not in the correct directoy. I think it goes something like a SOUND or SOUNDS directory and then under that there is an EN directory, and in that one are all the .WAV sounds.
And then it had preset modes . So the modes tab was missing the modes tab stuff . But its ok . Just arm with aux1 etc. Rates and pids were still there . But osd tab shuts betaflight off . And reciever tab with the rainbow stick lines moving chart thing disappears and it changes switches all over the place for some reason . But i switched back something spi reciever something something and it works niw . Not too hard if you did betaflight on a few other drones first . You can bind and fly the uru85 whoop without betaflight to a frsky controller if you read the instruction sheet . Mine was $75 came in 4 days . 3s whooop is outdoor motor strength and vtx range is same as big drones .
hey have you try plugging in betafpv nano elrs ? i tried is not working for me.. just want to confirm is only me ? Not on Elrs v2 … I tested elrs v1 it works fine. I tried creating a new model No luck
Interesting. Could this be used to control an ARRMA senton r/c truck too? I'd love to be able to use a twin-stick controller instead of the trigger+wheel type it came with.
Steve:
THIS was an OUTSTANDING beginner video!!! Great photography, focus, audio, clarity of your voice, screen overlays to clearly demonstrate WHERE the controls you were explaining are located. THANK GOD FOR THE PAUSE BUTTON! It was needed, but the information is there for us to repeat, repeat, repeat until we have achieved what you have shown us. THANK YOU!
I'm using this video to guide me through my older Jumper T-Lite, since it is much better and absolutely up to date for my Jumper T-Lite.
Respectfully, - Jim
Glad it was helpful
Knowing this video is here makes me a whole lot more confident for when i finally make the push out of RTF kits. I'm not sure how someone is supposed to figure all that out without some kind of tutorial to begin with... Alas, too many other things to spend money on for now though (including saving up for my own jeep), so I'll just have to be happy with my little kit for now. At least I'm flying! :)
I bought the full kit with elrs module and receiver. I am new to the hobby though so it would be really nice if you could make a tutorial on that :)
I need this tutorial to.
yeah same
I just ordered this 2 days ago, if I knew you were reviewing this I would have gone through your link. Sorry. Keep smiling
Enjoy!
Being new to this I'm glad your here to help. A Lot of good info in all your vids. Thankyou
You can switch the momentary switches into on/off switches in the logical switches page in the menu (page 9 I believe) then no more worries with momentary switch lrobs
I like such videos.. it helps a lot .. your way is capturing both my mind and loyalty to your channel ..can’t thank you enough Steve 🍀
My pleasure 😊
Captain I left the props on just like you and now I'm being rushed to the hospital.. 🥶🥶🥶🥶🤺🥶🤺🥶🤺🤫🤫 the drone took off and took 3 out humans before it crashed. Lol. Just playing. Great review buddy.. 💙💙💙💙🥶🥶🥶🥶
Mikey
Always have bandaids by your drone :-)
hahaha!
@@CAPTAINDRONE798 hehehehe shush.. 🤫🤫 lol
Mikey
Going back to the time when I was FPV greenhorn, I would really appreciate this video! Great informations for EXACTLY what all the newbies would need to get started, and then they can add features as they progress...
Features of the ExpressLRS module can be fully exploited by changing OpenTX to EdgeTX but that's not a topic for this video.
Great job Steve 👍👍👍
Thank you! I keep meaning to try EdgeTX but have not found the time to sit down and play with it.
Momentary switches are actually useful for FPV. They can be used as prearm switches to have an additional safety measure.
I always use pre-arm on anything that could hurt ya. Momentary is a must.
I've seen people use them as pairs (i.e., press both at once to set off a command). Other than ON/OFF temporary switches on a quad (lights on, lights off, or some external add on), I'm not sure what I'd use them for.
@@CAPTAINDRONE798 The idea is to only be able to arm while one of the momentary switches is pressed. Prevents you from accidentally arming the quad.
Good evening great video cool review
hi may i ask what type of protocol does the rc era uses
I did everything correct even added sounds to my channels. But when I save everything in Beta flight . Disconnect , turn off Kwad and Jumper t lite. When I turn it back on . The Model I took forever to create gets deleted back to MODEL # 1 etc.... Like the Controller reboots to factory settings when I turn it off. I tried again and I get the same results. Any idea whats wrong with my set up Capt> ?
You don’t set up sounds or models in Betaflight…. So I see where you’re messing the process up. You set up sounds and models in the radio and there is no SAVE button. When you create a model and give it a name every change you make is saved. BETAFLIGHT CONFIGURATOR is where you configure the FLIGHT CONTROLLER in whichever drone you bought, to react to the switches/buttons on whichever radio you have used to BIND to the receiver (whichever type it may be) that is in the drone.
@@CAPTAINDRONE798 I didnt create sounds in Beta flight. Did it in Jumper T lite page 10 I believe after setting Channels and used the sounds in the SD card built in. Just like in your video. I did everything perfect like in your video. Step by step. Works perfect. Its after all settings are saved in Beta Flight, Disconnect to it, Power off drone and controller where the problem starts. Again, when I turn on controller. The Model I named and created turns back into its original name " Model #1 " Like the Controller reset itself clean with all the work I did :(
@@rhysezfpvif you created something like 100 different models, you then select the one you want. Push in the select button when your on the model page.
Excellent Tutorial Video Steve. Thank You.
Control sticks 😉
Thanks for making videos for us.
Radiomaster zorro looks futuristic
I should have one at the end of the month to check out.
@@CAPTAINDRONE798 looking forward to that one for sure😊
Your instructions are awesome as well...
very good review. very happy and impressed that this rx has a trainer port. i wish my original t-lite had this so i could use as intended to train my son., he is 4 and uses my t-lite in liftoff and can fly acro but irl is very scary for me to watch and he almost lost his tinyhawk fs2 in about 15seconds lol. thank you for what you do and this is a great channel. p.s. i just realized i wasn't subscribed...i am now.
I’ve never seen anyone use the trainer port option so I’m totally unfamiliar with it. If anyone asks a question about it, feel free to respond. Thank you.
nice video, how to save the configuration jumper T pro, because after turnoff jumper T pro, the configuration is empty
It saves automatically, often it is on the micro SD card.
mine still going strong after 2 years mm spray deodorant in the gimbals they stay as new I love plastic hall gimbals ,, and still go to my jumper pro for the best flight experience ,, never lost a signal since owning , I like a light controller
the best video. thanks captain drone for teaching for newbie like me. im starting with t-pro
Hola
Por que al momento se colocar la SD al control con el archivo el control no encuentra los archivos
Why does the F3 EVO Brushed Acro flight controller with built-in DSM not respond to the movement of the Jumper T-PRO sticks?
The review as simple as useful for beginner as usual Captain Drone we learn hundreds lessons from you about FPV hobby... God bless you always ❤❤❤❤.
Much appreciated!
Один з найбільших переваг цього відео - поетапні інструкції. Це допомагає новачкам з легкістю орієнтуватися в складних процесах налаштування. Відео пояснює, як зв'язати дрон з контролером керування, як виконати налаштування пульту дистанційного керування і як встановити додаткові параметри.
Додатково, рецензент відзначає хороше пояснення основних функцій та налаштувань Jumper T-PRO дрону. Він розглядає різні аспекти пристрою, включаючи пульт дистанційного керування, передавачі сигналу, мотори, батарею та інші компоненти.
Незалежно від рівня вашого досвіду використання дронів, це відео може бути корисним джерелом інформації. Його ясна та зрозуміла презентація допоможе вам в освоєнні Jumper T-PRO та його налаштуванні.
Hello
I need help with charging of the transmitter. On its top there is a USB C port where I am suppose to plug a USB C cable and the charging should be on by default. But what's happening
- As soon as I connect the charger, The transmitter Power button light and LCD light comes on and goes out within a second. That's it. No indication or display for charging.
- I have to keep the transmitter ON and then keep it connected to the USB C charging cable "imagining" that it gets charge only when is ON. But still no charging indication is there. Since the Tx is ON it starts beeping after few minutes. Have to keep stick moving frequently.
What is the standard protocol for charging Jumper T pro?
Xm+ sucks! I would never tell anybody to get xm+ due to the close proximity failsafe. You can't arm with your radio too close or fly close to yourself indoors with small ducted whoops. I hate doing benchwork that requires the radio be connected with xm+. Ever had to check motor direction with your toe? I would also say that elrs is super easy too. Not as user friendly as frsky, but not too hard and well worth it when your comparing the performance/price ratio.
I sit down on the diveway and plug it in and wait til the light goes green to fly . Im about a foot away from xm+ .
Hi Captain Drone, can you bind this Jumper T pro with Cetus Pro?
Literally what I'm trying to do lol
@Silvan Pierce I tried and successfully bind the Cetus Pro with Jumper T pro, try to follow the steps in this video, when he presses the original factory bind button you press the bnd inside the menu of Tpro, remember to choose Frsky D8 ua-cam.com/video/24bjbRqQqjw/v-deo.html
In order to bind this to any drone you have to find out what type of receiver is in the drone you are binding to, then select it in the remote. I have no idea what receiver is in the CETUS PRO.... could be a D8 receiver, & if that is the case you could bind it to the Jumper, however, the CETUS PRO is not BETAFLIGHT which means that even if you did bind it, you'd have to use some type of software from BETAFPV to configure what switches do what.
Hi @CAPTAIN DRONE , I follow exactly your steps by configuring I05 ANF I06 to the SB and SA switches. Now they work flawlessly, thanks a lot!
Very nice a definite keeper. I have 18650 Flashlight Batteries.
Wow!
@@CAPTAINDRONE798 I should have said it different. I wasn’t trying to say 25-30 batteries was a lot. I was just trying to refer them as Flashlight batteries and not Vape batteries. Flashlight collector’s usually buy Cells by the case for a much better deal.
Awesome my friend, will check it out!
what is the simulator at the 10min40s ? very realistic.
Really good information thanks for looking out
It is a nice video, thank you.. I want to ask a question about failsafe... On my jumper t pro (ELRS version with 3 receivers)I couldnt find the failsafe settings menu. It has to be On model setup menu/ Internal RF/ Failsafe .. but It doesnt exist. How can I solve the problem..
I believe it is on Page 1 or 2 of the model setup.
@@CAPTAINDRONE798 thanks for your early reply, but it doesnt exist in the menu. there is only internal RF section . I select internal rf crsf and there is not any failsafe option there. :(((
@@egemenx5813 You are close but looking in the wrong area. Scroll father down.
@@CAPTAINDRONE798 on open tx yes it is close the area you said. But on edge tx there is not any menu about failsafe. Especially with internal elrs it doesnt exist :((. I think , I will set it on Inav CLI section.
kool, Cap.
I have jumper t pro elrs version transmitter but I want this transmetter to control two drone separately but it have 1 reciver and this reciver is not available in market then can i use radiomaster elrs and other elrs reciver connect with jumper t pro does its work ?Will it work? And if I do, which receiver should I use?
Normally NO, only one receive is connected at anyone time so that you don’t accidentally fly your friends drone unexpectedly . However with some receivers (cheap 3rd party ones) they get sloppy and can connect to a signal so more than one is in use
Hi Captain! Will this controller work with the GepRC TinyGo?
Hello...very nice video thank for sharing👍🙏
If you're brand new to RC and don't have a transmitter yet, I could see the appeal of this, but man this thing looks cheap. I think RadioMaster is ultimately going to win in this gamepad style matchup.
I think the regular Jumper T Lite made alot of headway and this is going to be a step above especially in a month or so when they install the express elrs as part of the internal source instead of having it be external. It's going to be a game changer I think and I know from my Jumper T Lite that it doesn't feel cheap and I'm sure this one will feel even better. No way will this lose to radiomaster.
lol weird. i feel like the radiomaster looks like a toy. to each their own though.
I got the built in ELRS version which looks from the images it comes with the usual T antenna, please tell me I don't need to open it and buy another antenna to put in it????
No upgrade needed, it works out of the box.
I just tried binding elrs . No bind .
So i tried an r9m . The tpro has r9m in the setup but the r9m instructions don't match what the jumper setup says or does .
I tried holding the rx button and plugging in the battery and put jumper in bind and press the roller knob and selected 8 ch no telemetry and press the roller knob again and it chirps like an frsky bind noise . But nothing binds .
All is well with your radio. ELRS binding requires that the receiver and radio are on the same firmware. I assume you have an ELRS module attached to the rear of your T-PRO. R9M... never tried it. But binding to receivers other than ELRS is usually much simpler as the firmwares do not need to match. Your must be new at this which can be daunting for beginners.
@@CAPTAINDRONE798
I managed to bind a crossfire rx instead . The tbs crsf micro will bind to a new unused crsf nano without lua script or computers or flashing or firmware upgrades or matching rx's or buying more computer parts to finish making 💤💤😴
Anyone know what protocol is used for the eachine boats like Eachine EBT02?
I really wish i got this instead of the radiomaster zorro.
Good job Steve......I like this controller!
I bought the elrs version of this jumper t pro I thought I can bind it to my armor 65 lite that uses bayang protocol but it is not working at all.. I've heard I need to buy a multiprotocol for it, is it true? Is this jumper elrs not multiprotocol already? Please help me understand this...
ELRS is always only ELRS, so if what you are attempting to bind to is not ELRS then it will never bind. You sound very new to the RC hobby which means that even if you purchased the 4-in-1 version you’d still have difficulty binding the radio to your drone. What I mean is that you need to do research on how to setup a model in the radio, as well you need to know what receiver is in your drone & how to bind to it, and then how to use BETAFLIGHT for configuration.
@@CAPTAINDRONE798 Yes you're completely right, I'm new to this hobby. I've heard that I need to install external module to it if I want to control non elrs drone.
@@ayocak Yes, I believe there are external 4-in-1 modules but I’ve never tried one.
Hi, I bought that same pack but I can't get the bars to move in BetaFlight. I have flashed RX and TX with ELRS Companion and when I want to load the files with OpenTX it tells me that it is incompatible. Could you do a tutorial installing the RX in any drone?
I have an inoperative drone because I'm waiting to install the RX and get it working....
Is a review of the radiomaster zorro on the horizon?
Once it is released, yes.
Hmm I saw JB's video on this RC and he said you can use the shoulder buttons, how would you assign those in betaflight and bind them as well?
BETAFLIGHT is your answer for assigning the switches/buttons
@@CAPTAINDRONE798 even with the use of logical switches?
i have rc car with flysky gt3c radio, can i use the rx and bind to jumper t pro? or do u have any recommendation rx to connect jumper t pro to my rc car? thank you
Depending on the version of receiver (what type of flysky receiver is in your car... is it a unit that has a bind button or can be put into bind mode) it would most likely work because Flysky is one of the most common receivers on the planet and many radios work with it.
How to connect Happymodel Cine8 Frsky SPI D8 RX?
Very great video! i just followed the steps and everything was great! i just got a problem: when i check on BF in the "receiver" menu, Roll Pitch Yaw and Throttle are mixed and is a mess. For example: the Throttle stick on the radio makes move the pitch on BF, and the Throttle on BF is actually moved by the Roll stick on the radio...any suggestion on how to solve the problem? many thanks! this has never happened to me before, and both drone (moblite7) and the jumper t pro are new, so i can't understand which one is faulty...
Have you figured it out yet? The solution is rather simple.
@@CAPTAINDRONE798 yes! I found out the solution: it was in BF, instead of AETR it was on TAER mode…8)
@@enricodadamo4032 Excellent! Happy flying.
Hi,
Do you have an instruction on how to connect this to an ELRS 2.4? thanks
Watch my review tutorial on how to setup and bind an ELRS drone using the Radiomaster POCKET. The procedure is almost identical.
@@CAPTAINDRONE798 Thanks will do, I have a built in ELRS on my Jumper T pro but I cannot see the binding process in my remote.
@@CAPTAINDRONE798 I checked your video but it seems that the seller provided me an incorrect item, I can't seems to find any ELRS option in my remote. Ohh! well, might be sending this back.
@@zenargaming1257 Are you sure you watched my video? The answer is right in front of you but you are not pressing the correct button and it may be to complicated for you at this time. I think you need to enlist help from someone in the FPV hobby if you have someone near you. It is a very simple process and eventually you’ll figure it out (everyone in the FPV hobby had to figure it out).
@@CAPTAINDRONE798 Thanks, I found it. It seems that I need the Lua to see the ELRS.
You never said what that simulator was you used, nor are there any links in the description about it. So what was it?
I just added the link to the video... have a look.
Hey, I bought the controller for my new fpv hobby. First of all I want it to connect with my labtop for the simulator. When I connect it with my labtop with USB c it don't ask me if I want to use it as an controller. I find no options to connect. Can someone help me please. Ian really frustrated and it's so easy for sure. Thank youu
How do I make the acro mode? In your video it was only Arm , angle, and horizon
Watch again, it was Horizon, Angle, Acro. Acro means there are no restrictions and that is the default for all FPV drones, so this is why there is no option in Betaflight to select a mode called Acro. When the Modes Horizon and Angle are NOT SELECTED, then it means the drone is in ACRO.
@@CAPTAINDRONE798 ahh gotcha, thank you so much for the explanation!
Hi Steve,
Thanks for the video's.
I'm looking to get into FPV flying. (cinewoops)😎😎
My idea is to start first with the Jumper T-PRO RC to practice on simulators and for later to fly with it.
Then, buy the DJI Goggles Integra before buying cinewoop drone with Ocusync 3.
Do you think this is a right approach to start?🤔? thanks!
All good except the part where you mention ocusync 3… that does not exist in the FPV world. Perhaps you meant DJI 03 Air unit.
Thanks Steve, yep, ...that's what I meant😔 - the DJI 03 Air unit.
Thanks for all the information you share, now i know were to start😎
real simple.. are you taking the P? 5 days iv been at it both updated & binded i set buttons & sounds from this vid now i have sintax error on mix ch sa WHEN USING WIZARD THERES NOTHING ON THAT BUTTION
Hi steve:
Can i use betafpv elrs nano tx module on jumper t pro
I’ve not tried it but yes it should work as long as you have the correct ELRS script and your radio is up to date.
So I am trying to set this up and when it got to putting the sound track on, it said that there were no sounds on the SD. And I went and checked on my computer and it had a while sounds folder. Please if you could help that would be great. Also very nice tutorial so far!
All 4 in 1 and ELRS radios use an OPEN TX or EDGE TX software. That software has to find the sound files in a particular directory. If they are on the micro SD card but in the wrong directory, it can't find them.
Best tutorial ever! Thanks !
You're welcome!
Newbie question! This controller will not connect with an ELRS drone without the additional module attached to the back? That seems a little clunky if I'm just looking for an ELRS controller. Thanks!
Simply buy yourself an ELRS radio. JUMPER makes an ELRS version and so does RADIOMASTER
@@CAPTAINDRONE798 Perfect, thank you!
Hi, which receivers are the 4 in 1 t pro compatible with? Do you have to buy external receivers midules? Thanks!
The website should have a list of all the compatible receivers.
And again ... Thanks Man! Maybe i can retire my T16. Its overkill for this hobby. Bigger is not better!
My biggest complaint about my t lite is the screen,.my old eyes struggled with it. The controller apart from that was great , gone to the eachine tx16s now...
This screen doesn't look much bigger than the t lite.
Order a Radiomaster Zorro instead, bigger screen! That's what i did, now gotta wait for it to ship!👍
One thing I would of mentioned before purchasing the drone is whether or not the xm is ACCST. It will not work with that radio. I ran into that early on and submitted a question to you which you really didn't provide an answer.
Good point... I forgot about FRSKY and that mess. The good thing is that pretty much all FPV drone companies use the knock off FRSKY XM+ in drones purchased which is not ACCST.
I just bought the jumper t-pro with built-in ELRS... mine already has the latch button on the back the SD card in it and sound already mine says Edge TX when I turn it on. is that different than open TX? I guess for some reason they updated mine and sent it with a memory card..
Yes, you have the version that came after the one in my review. Edge TX is newer than Open TX.
Good instructions Steve. I have not flown an FPV drone but looking for a contoller to use a simulator to learn what is the best 1 to buy and what simulator program to get.
Try and get the now older T-Lite. Perfect for sims and very inexpensive.
HI Steve i just receive My t PRo -i Order With ELRS module and receiver but they dont add me the receiver CAN you help me to Choose One GOod REceiver ?? for this Module ? the stock one they say can go up to 5 kmh
THAnks Steve !!!!!!!
You can pick pretty much any ELRS receiver. Just make sure that it matches the frequency of your module (2.4 G or 915 MHZ). Then make certain your receiver and module are on the same ELRS firmware, and they will bind.
@@CAPTAINDRONE798 thanks Steve I send you email with module check it if you can it doesn’t power on only when I Insert type c cable in module power on 😭😭.
I got a reversed screen now on my jumper... so everything is mirrored.. HELP?
hello,would it be the same to set-up a drone that does'nt have acro,i know i should be able to set-up for a bugs or mjxq since its in the list of suported protocols,the original controler stoped working so i'm getting a jumper t-pro so i can also get a freestyle quad later on,so the bugs original controller has one momentary button for arm disarm,a momentary button for high and low speed,and a momentary botton for 360 flips but i dont realy care about that one,thank you in advance for your time
The setup shown in this video is for the FPV Drone hobby.
@@CAPTAINDRONE798 thanks,i thaught you would be able to help but gess i was wrong
Holy Crap! Land of ICE!
can you use spektrum receivers with this?
Spektrum receivers are supposed to work with the 4 in 1 module. Check the JUMPER website as they show what receivers are compatible.
What FPV simulator are you using in this video it looks really cool.
It is called FREERIDER
I have question will it connect to the Aton Traxxas drone ?
It does list Traxxas as a protocol. Not sure how you’d bind it since I’ve never used that drone.
@@CAPTAINDRONE798 When you ever have a chance please fly that Traxxas drone the Aton Traxxas it’s super fast very nice drone I would like to see you fly that drone and make a video off of it I will guarantee you people will fall in love with that Drone
Is it the same setup for the internal ELRS controller and binding to a Jumper 2.4ghz ELRS AION-RX-MINI RX? Im new to this hardware.
In the old days we had a crystal in the control and receiver lol
Model setup is the same. Only difference for ELRS is that for the receiver you normally select CRSF.
@CAPTAIN DRONE I have watched your video and created an arm switch but the problem is that when the switch is down BF sees it as high, than in the middle is sees it as low, and also for the up position. Seems inverted
I have set the switch for 2 way in the control settings but it always uses the middle of the switch to change values in BF.
I want use it as a 2 way switch, like down is a low value, and up is high value without the middle of the switch changing any value.
How can we do that?
So as you say this binds to hobby grade drones but the protocols have hubsan and bugs etc what does that mean? As I associate them with the likes of the bugs 16 pro etc
BUGS used to make FPV drones. Hubsan as well.
@@CAPTAINDRONE798 oh, everyday is a learning day thanks for the reply..I just lost my one day old bugs 16 in a 70ft tree due to a bird strike 😭
I'm looking to replace my old DX7 that I use for my helicopters. I wonder how it would bind to the Spectrum satellite receivers?
The list says it binds, but I've never tried it. It is using the same common chip similar to the JUMPER T18 and other multi protocol radios, so you may wish to see if there is a video on youtube with a radio using this chip.
Great video, but does anybody know if you absolutely need a computer to do this
you can use your phone to download the required files into the micro sd card.
U are rly helping me with my fav experience. THANKS!
Happy to help!
hi, I can't find version 2.3v0038, where can I find it?
Same problem
So im confused , should i get the ELRS type without the back ELRS module backpart and still be able to use the 4 in 1 or do i have to buy the 4 in 1 and never update my future drones with ELRS receivers? im confused im a beginner sorry :D
If you get an ELRS controller, then that means you pretty much wish to only fly drones with an ELRS receiver. If you get a 4-in-1 controller, then that means you wish to fly drones with all types of receivers and then have the option of adding the ELRS module.
@@CAPTAINDRONE798 Hey , I followed ur guide to were i can i have elrs one so a little differend. but in the modes i got everything setup like u do but ur arm disables with aux to the left but mine is completly to the right..
Hello, i am planning to buy a flywoo firefly hd fpv. and i dont know witch controller i will buy, somehow the goggles i choose is dji. but i have a tight budget for choosing a controller, can you make a suggestion which one should i buy?! thank you very much
If you need a BIG screen then you want something by RADIOMASTER. If not, then pick anyone and you'll be happy. You just have decide if you want a 4 in 1 chip model or an ELRS model.
Thanks for the video! Did anyone try to bind the controller with a Happymodel Cine8? Didn't work for me 😞
It all depends on what receiver is in the Happymodel
@@CAPTAINDRONE798 I forgot to tell, it’s a FRSKY SPI.
@@jgacarneiro Now that is one item I have never owned. Not familiar with SPI, sorry.
@@CAPTAINDRONE798 thanks for your concern, my friend. I’m a newbie in this activity, trying to learn everything. Hopefully soon I’ll be flying my quad. Your videos are amazing. Thanks for sharing with us. A fan from Brazil 🇧🇷
I want to kill myself after watching this.. lol lol. Captain why can't they make all fpv drones just like the DJI FPV. It just works.... Lol
Mikey
This is why it takes knowledge to get into the RC Hobby. We all said the same thing as you and then gave in and learn’t all the crazy rules. :-)
Versatility vs. ease of use.
Ok so I bought the Jumper T-pro with built in ELRS. Does it still do all the other protocols?
Nope, I believe it should only do ELRS. Some ELRS radios also can do FRSKY D8 & D16 receivers, but not sure about the Jumper.
Is the Frsky R XSR protocol supported?
Thank you
Should be since it is a 4 in 1 chip
I got a jumper t pro radio, and am trying to bind an frsky rxsr reciever to it's 4 in 1 multi mode, The videos show how to go to multi mode than select "frsky x" which is supposedly the correct mode and select that, but in multi mode on my radio frsky x doesnt show up, WHY COULD THIS BE
Watch my video on how to setup the RADIOMASTER ZORRO and bind to a drone. I bind to the FRSKY RXSR... watch the vid and pay attention to what I select.
This is awesome video you guided well how to download the file and create now model .....surely it will help alot out there👍👍
Got to " Play Track " after that " no sounds on sd > exit " ? i copied both of the latest SD downloads and both give me the same message . i opened both files on Windows and the files are complete and play the SOUNDS ??? help
It sounds like your .WAV sounds are not in the correct directoy. I think it goes something like a SOUND or SOUNDS directory and then under that there is an EN directory, and in that one are all the .WAV sounds.
My jumper tpro just beeps and beeps in bind . It has an spi reciever . I put it on frskyX . Is that wrong ?
So i tried frskyX and when you switch to "subtype" d8 it switches the "type" to frskyD .🤔
And then it had preset modes . So the modes tab was missing the modes tab stuff . But its ok . Just arm with aux1 etc. Rates and pids were still there . But osd tab shuts betaflight off . And reciever tab with the rainbow stick lines moving chart thing disappears and it changes switches all over the place for some reason . But i switched back something spi reciever something something and it works niw . Not too hard if you did betaflight on a few other drones first . You can bind and fly the uru85 whoop without betaflight to a frsky controller if you read the instruction sheet . Mine was $75 came in 4 days . 3s whooop is outdoor motor strength and vtx range is same as big drones .
Can we changes mode 2 for mode 1 in this radio jumper t pro? Because i don't find jumper t pro in mode 1. Thanks.
Yes
Hi, building my first drone and would like to know if you can add buttons to make RTH, hover and automatic take off to this transmitter. thanks.
You can add any feature you wish since it is your typical programable radio
Nice drone
2:23... Gee they really should put that list in Alphabetical order..... Thanks for showing the new Flyers the OpenTX binding of a Drone.
I agree… I discover new items each time I look at it.
good video thanks a lot
can i use this with my DJI FPV drone
Nope. That drone only works with the included controller.
How to select Receiver RX Setup to AFHDS-2A mode for Jumper T-Pro JP4IN1?
hey have you try plugging in betafpv nano elrs ? i tried is not working for me.. just want to confirm is only me ? Not on Elrs v2 … I tested elrs v1 it works fine. I tried creating a new model No luck
The ELRS that comes with the Jumper is not yet supported.
Meine Schalter funktionieren nicht ( werden nicht erkannt) can someone help me ?
To helpful videos, thank you so much.
You're very welcome!
Interesting. Could this be used to control an ARRMA senton r/c truck too? I'd love to be able to use a twin-stick controller instead of the trigger+wheel type it came with.
Yes, you may or may not have to change the receiver in the ARRMA.
@@CAPTAINDRONE798 check that the protocols match