Your shop is nothing short of amazing!! I love how you don’t have to double check the measurements on your table fence. Your attention to detail is outstanding in every aspect.
Love your videos - one tip from a woodworker learning about building sub boxes - When you used CA glue for the braces - one good tip is to use both CA glue and wood glue - you can use wood glue for most of the joint but leave a point on each end of the joint for CA glue. The CA glue acts as you wanted (quick solid connection when you didn't have a brad nail that would work), the CA glue then allows the wood glue to make an stronger bond for the remainder of the joint (with the CA glue acting as the brad or clamp as the wood glue dries).
I’d like to see that router video and maybe highlight what bits would be better for beginners to purchase because the cost of tools definitely adds up!
router video? yes, yes, and yes! i have a router but i currently only have 4 bits. they are so expensive and the different types appear to be infinite. I would like to know more about the tool in general, best applications for use, and mostly the critical/necessary bits i need and will use the most vs the ones i can do without and pick up later
i have respect for the shallow woofers since i installed one shallow 12" in my 02 dodge ram quad cab. i will be using them more in the future for my other vehicles!💪
@@parkerprecision6675 you may be able to find the under seat speaker box on fb marketplace. they come in dual and single units. i have a single unit, so i have some interior storage. i have a shallow 12" kicker comp rt, run by an Alpine 500w amp and a 1 farad cap. i ruined it using the SMD DD1 and CC1
I have installed the JL Audio sub in my spare wheel(spare does not have extra holes, just the 5 and the center hole), that I have sealed the holes, with a rubber seal and an aluminum 6" "washer", all bolted down to the car. Placed an MDF over the wheel, made the cutout for the sub and the speaker terminals and strap it, with two ratcheting straps. It hits haaaard. Spare has well over 1.3 cu/ft.
I've had an idea for a while that I think would be the best of both worlds for someone who wants to ground pound, but still wants some cargo space. I'd like to see a "wall" of shallow mount subs, laid flat on the floor of an SUV. Maybe 4 or 6 subs in a "wall" configuration. Either 4th order bandpass, or down firing (more or less the same concept). I don't care to take credit for the idea, I just want to see someone do it. Since you have sponsorship, maybe suggest the idea to a sponsor, and maybe give us a video. Keep up the good work.
1. I'd LOVE to see you do a full Router vid. 2. Please do the wood inlay. That's something different than you've done in the past, which is always good! 3. Is that a new table saw setup? What table saw and vac system is that?
Im sure there is a legit calculation to how much space. With that being said, ive had great results with 1/3 clearance. So a 10" would 3-1/3" off the floor, 12 would be 4" and so on. I mesure off of the surround.
Mark, bring on that router table video. There are plenty of veneers you can use in that center piece. That’s up to you. I have seen this done in homes where the sub was made up to look like furniture. High end clients willing to pay for slick work. Your skills are right in line with that! Roll it!😊👍🏻
I have to say that you have inspired me alot, I've been building my 3rd sub box now. And I can say that thanks to your videos, it turned out amazing. I am incredibly happy with the results and all the ideas you gave me, the how to only use simple tools only video gave me alot of help. Thanks!
I thought JL says the TW series isnt designed to play in a ported enclosure? Maybe that's just the TW5? But I was looking at the tw3 as well and all videos or forums where it was brought up always ended with JL professional or enthusiasts say don't. Either damage will be possible or they wont play to their potential. If not I'd love to see what you could do with a TW5 enclosure. :p I love mine and I'm tempted to get a second one but I'm trying to decide how I want to design the box to hide in my spare tire area. I wish I had a work shop like your to build in. You have some of the best builds and the tools that give you and edge are amazing. Cant like your vids enough.
Love it, been thinking about building a box like this in my BMW F20 118D. Today i have a regular sealed wedge box (30L) with a Dayoton Titanic MK IV but i'm a bit afraid of damageing the sub when i put stuff in the trunk :)
I think the router video is a great idea. And if you do it. I think it would be a good idea to you use each type of bit, and show what it can do (what it looks like, and an example of a car audio use for it). So it's easy for everyone to understand what they all do. ✌️
hello master ... I'm from Indonesia very interested in your channel, can you give me an example of making a subwoofer box on a Mitsubishi L200 Triton GLS 2010. Thank you
Great video man. I haven't watched your channel for a minute, and you've definitely improved your skills IMO. That's the most professionally built car subwoofer I've ever seen I think. Very impressive! ✌️
Can you do a video on hard Corner consequences? I've never understood why we wanted to round. I have a pretty good idea but would like a clear concept. Thank you
Could you include a video on how you decide on which router bit or profile you choose and how to properly set them up. Like how you make perfect round overs etc... that would be great.
You should design a good subwoofer box/setup for a Jeep TJ! the aftermarket community is lacking in that category but I feel a ported box for downfiring dual 10s would be awesome! SubThump has one but I feel they leave airspace to be desired in the height category. Wanting that low boomy bass for rap and such.
Tht would be a good idea to show in wht all the bits of the rotor and how it works and I'm getting one soon and I wanna know witch ones I would use the most
Great work as always. I was gonna bust your balls on using the miter sled and fence at the same time then noticed your little trick. Very nice! You show off good saw practice.
Great video, but can this work in a 2018 BMW 7 series with a Bowers & Wilkins factory sound system. Also, note that i have a spare tire package which i can remove to make more space. Thanks
I've been trying to shoe-horn in a 15" sub into a boat for weeks now. Trying to fit it under the helm where the factory sub was in it's "enclosure" which was neither sealed nor ported, and fiberglassed into the hull. I've made 2 sealed enclosures so far based on manufacturer's recommended volume and neither have been able to fit. For such a simple hobby, this shit sucks lol
I take pride in my work area, I know it's not macho man dirty but I believe a clean well organized shop is usually a sign of caring about the results of the finished product.
I would like to see the router video. I plan on getting the Porter Cable router mentioned in one of your previous videos. I would definitely like to see some of the tricks and the bits that you use to fabricate your designs. Thanks for all of the incredible and helpful videos! Your videos are exactly what car audio fans are looking for..help and tips!
question a sealed box with that has a chamber divider for 2 12" subs in trunk, will it sound the same if you have 2 sealed boxes, one 12" sub in each box still in trunk?
I like the idea of using the wood grain material as a inlay to create a more dramatic look. Personally I'd rather see a piece of carbon fiber (even a piece of formica covered in some 3M faux carbon fiber vinyl). I just don't care for "natural" materials in obviously high tech modern vehicles. I'd prefer high tech or modern textiles or maybe a sheet of brushed or polished aluminum. Maybe with your logo created in a high gloss polish and the area around it brushed. I don't know, you were asking for opinions and that's Just mine. Keep up the great work and great tubes, looking forward to the next one.
I've been using a router table and trim router for only about 6 months and even now i keep seeing many different bits that i have no idea what i would do with them. I could also use some tips on different ways to use a router
Yes on router video, specifically flush trim bits please. Straight flute versus spiral, why and when to use one or the other, I've only been using straight. Also, what would you call that type of bit you used at 9:10?
Serious question... in a 4 door pickup why are down firing subs under the back seat better that up firing subs?? What about a single forward firing? Wouldn't that be even better?
this is quite a bit late after the vid was released, but have you ever built a custom box for a Nissan Frontier? I just installed a JL Audio C1 690 in the front and the C1 650x in the rear and haven't quite figured out what kind of sub or box to go with. What are your thoughts on this one?
I have 2 pioneer shallow mounts I’m gonna put under my seat haven’t installed yet but the boxes are sealed do you recommend a ported box or sealed for these speakers I like all music but also like deep bass when jamming to anything there’s not many vids that have comparison
Brother.... What an excellent video! I guarantee you so many people learned some new techniques, as well as the right techniques, from your descriptions and work. Real quick, what bit that you used with your router to add some depth as you took away material for your speaker binding posts? Thanks in advance and can't wait till the next video!
Can you make a video on how to calculate air space and build a ported fiberglass enclosure? I have an 11 camaro ss and want to build a enclosure tucked into the side of the trunk space.
Tried cutting with my handheld router and a small bit yesterday, it jumped so much I used a chainsaw instead. I am serious. I need to get a Bosch jigsaw. I would love for you to explain how the upwards firing router works and is assembled.
I would like to see you do a sub enclosure for a 5th Gen 4Runner. Your layered box you made for the Jeep turned out great, but I wonder if you could show us another solution that may be different. I had a custom fiberglass box in my older 4Runner and loved it, but that was a long time ago. I'm curious about a setup with 3 or 4 8" woofers, or maybe using shallow mount 10's could leave you with more options to make a box that is better hidden.
Help!!! I have 2 Memphis 12s in a enclosed down fire qbomb probox and the excursion is too great and it is rubbing or hitting my floor mats…. What could I do to correct this issue?
Could you give a guide on how far off the floor a downward firing sub should be spaced. I know you can get gains and losses depending on how close they are.
Ive always pushed JLs all my live for the passed 18 years but right now im pushing 2 13.5 jlw3v4 what box and dimensions do you recommend. I would really appreciate it
I just pick a set of kicker lt7s shallow subs 12s n there r going b hind the seat of a 03 silverado single cab i need two boxes one for each side so i can move up n down the center consul thers about 22 wide n 16 high n 7-8 deep u have a diagram for the boxes can u make it to kicker seald specs thanks
Looking for some advice. I just got two 2000 pyle 15's I have a 2000w amp for each sub "both in the same box with separate inputs but each speaker has 2 inputs how do I wire them
Hello, I was wondering what would be the best box ( ported or sealed ) for a 2016 Chevy colorado extra cab 4 door. And would you have a design for that. I have searched your site and did not find anything. I need an under the rear seat down fire box for a jl audio shallow mount tw3. Thanks for your help
I'd be up for that router video. Just picked up a Bosche router with table but have yet to use it very much. Also any thoughts on a quick disconnect subwoofer? For example, I know several people who are hesitant on getting a sub installed as it takes up a permanent spot in their trunk. It would be awesome if there was a way to make a quick disconnect subwoofer that can be removed in seconds and without tools. This would be for people who have a limited trunk space but don't want to compromise for a sub, for say like a road trip or when they really need to use all of their trunk space Another video that might be great would be best ways to secure subs in the trunk, especially for people who don't want to drill a sub into their car or make any other permanent modification.
I know this isn’t really your area but could you possibly do a center console build with speakers inside? I can’t find anything on making a custom console or any piece that’s as thorough as you.
me 2 brother ima big fan been watching your channel for years i was trying to see what brand is your plate earlier 😅 on a different video of yours but since you mentioned it yes i would love to see all those router tools
Great video! Just wanted to ask, which wiring configuration are you using? I have two exact subs but 12” and just wanted to know how to wire them properly. I have a jl audio hd750/1 mono amp too
Your shop is nothing short of amazing!! I love how you don’t have to double check the measurements on your table fence. Your attention to detail is outstanding in every aspect.
Love your videos - one tip from a woodworker learning about building sub boxes -
When you used CA glue for the braces - one good tip is to use both CA glue and wood glue - you can use wood glue for most of the joint but leave a point on each end of the joint for CA glue.
The CA glue acts as you wanted (quick solid connection when you didn't have a brad nail that would work), the CA glue then allows the wood glue to make an stronger bond for the remainder of the joint (with the CA glue acting as the brad or clamp as the wood glue dries).
That's a very nice setup, I've never seen woodworking that clean and dust-free!
I’d like to see that router video and maybe highlight what bits would be better for beginners to purchase because the cost of tools definitely adds up!
router video? yes, yes, and yes! i have a router but i currently only have 4 bits. they are so expensive and the different types appear to be infinite. I would like to know more about the tool in general, best applications for use, and mostly the critical/necessary bits i need and will use the most vs the ones i can do without and pick up later
i have respect for the shallow woofers since i installed one shallow 12" in my 02 dodge ram quad cab. i will be using them more in the future for my other vehicles!💪
i just bought an 03 quad cab. any thoughts on a good setup for under the rear seat?
@@parkerprecision6675 you may be able to find the under seat speaker box on fb marketplace. they come in dual and single units. i have a single unit, so i have some interior storage. i have a shallow 12" kicker comp rt, run by an Alpine 500w amp and a 1 farad cap. i ruined it using the SMD DD1 and CC1
I have installed the JL Audio sub in my spare wheel(spare does not have extra holes, just the 5 and the center hole), that I have sealed the holes, with a rubber seal and an aluminum 6" "washer", all bolted down to the car. Placed an MDF over the wheel, made the cutout for the sub and the speaker terminals and strap it, with two ratcheting straps. It hits haaaard. Spare has well over 1.3 cu/ft.
You got more router bits than Norm Abrams!🤣🤣🤣
Hehe
I'm surprised there are this many guys old enough to know who Norm Abram is
You mean that young guy who tried to replace bob villa?
I've had an idea for a while that I think would be the best of both worlds for someone who wants to ground pound, but still wants some cargo space. I'd like to see a "wall" of shallow mount subs, laid flat on the floor of an SUV. Maybe 4 or 6 subs in a "wall" configuration. Either 4th order bandpass, or down firing (more or less the same concept). I don't care to take credit for the idea, I just want to see someone do it. Since you have sponsorship, maybe suggest the idea to a sponsor, and maybe give us a video. Keep up the good work.
Yes aid love a video just about a router table. Thank you in advance
my brother has 4 of these in his mustang. full custom build looks and sounds really good
1. I'd LOVE to see you do a full Router vid.
2. Please do the wood inlay. That's something different than you've done in the past, which is always good!
3. Is that a new table saw setup? What table saw and vac system is that?
I think he uses the sawstop saw...
Are there any guidelines for how far the front of the sub shod be from the floor of the vehicle (other than greater than Xmax)?
Im sure there is a legit calculation to how much space. With that being said, ive had great results with 1/3 clearance. So a 10" would 3-1/3" off the floor, 12 would be 4" and so on. I mesure off of the surround.
If you need a box design, Mark is the way to go. Top notch design with detailed layout. Can;t say enough good things about the process.
Appreciate that! Thanks!
How do I go about ordering box build plans from Mark and how much does it cost ?
Mark, bring on that router table video. There are plenty of veneers you can use in that center piece. That’s up to you. I have seen this done in homes where the sub was made up to look like furniture. High end clients willing to pay for slick work. Your skills are right in line with that! Roll it!😊👍🏻
I have to say that you have inspired me alot, I've been building my 3rd sub box now. And I can say that thanks to your videos, it turned out amazing. I am incredibly happy with the results and all the ideas you gave me, the how to only use simple tools only video gave me alot of help. Thanks!
I do wanna see that router vid..
I thought JL says the TW series isnt designed to play in a ported enclosure? Maybe that's just the TW5? But I was looking at the tw3 as well and all videos or forums where it was brought up always ended with JL professional or enthusiasts say don't. Either damage will be possible or they wont play to their potential.
If not I'd love to see what you could do with a TW5 enclosure. :p I love mine and I'm tempted to get a second one but I'm trying to decide how I want to design the box to hide in my spare tire area.
I wish I had a work shop like your to build in. You have some of the best builds and the tools that give you and edge are amazing. Cant like your vids enough.
My question as well? Mine Is sealed
That box turned out SWELL! 😋 your box builds are always top notch Mark!
Yes. A router vid would be great. Thanks!
Simple install on a jk 2drs with a fire down box
Dude you are so passionate about this, why not make home audio videos and tutorials as well?
Router video??? Sounds perfect, I really don’t like routers, but I see a need in the future. So yes!
Even when building simple, you build quality
Love it, been thinking about building a box like this in my BMW F20 118D. Today i have a regular sealed wedge box (30L) with a Dayoton Titanic MK IV but i'm a bit afraid of damageing the sub when i put stuff in the trunk :)
Have a few topics for a video.
Upgrading batteries? Ah?
Tuning for cabin frequency?
Testing ground resistance?
I think the router video is a great idea. And if you do it. I think it would be a good idea to you use each type of bit, and show what it can do (what it looks like, and an example of a car audio use for it). So it's easy for everyone to understand what they all do. ✌️
A big YES please to the router video Mark! :-)
hello master ... I'm from Indonesia very interested in your channel, can you give me an example of making a subwoofer box on a Mitsubishi L200 Triton GLS 2010. Thank you
Why didn’t you put the port on the bottom also facing down.
Great video man. I haven't watched your channel for a minute, and you've definitely improved your skills IMO. That's the most professionally built car subwoofer I've ever seen I think. Very impressive! ✌️
Keep doing my best to get better, I definitely find humor in my old videos
@@CarAudioFabrication mark! Is it possible to install 2-w7 8 under the seat of a 2015 f-150 xlt?
Yes Mark please make a router video! I bought a router because of your videos.
Can you do a video on hard Corner consequences? I've never understood why we wanted to round. I have a pretty good idea but would like a clear concept. Thank you
Could you include a video on how you decide on which router bit or profile you choose and how to properly set them up. Like how you make perfect round overs etc... that would be great.
How do you do the box volume and port calculations?
You should design a good subwoofer box/setup for a Jeep TJ! the aftermarket community is lacking in that category but I feel a ported box for downfiring dual 10s would be awesome! SubThump has one but I feel they leave airspace to be desired in the height category. Wanting that low boomy bass for rap and such.
Router vid and maybe a vid on basic fab tools when you live at an apartment or have limited space.
Like first, watch second
You want a cookie
Scott Boutiettel Yeah please. Give me, i love cookies😄
Do both son!AT THE SAME DAMN TIME
@@carloscastoreno8572 🤣🤣🤣
Carlos Castoreno multitascing, WROOM
what happens if you put a shallow mount subwoofer in a normal subwoofer enclosure
really enjoy your content, I always learn something new. Nice vid, thanks for sharing.
Tht would be a good idea to show in wht all the bits of the rotor and how it works and I'm getting one soon and I wanna know witch ones I would use the most
Stupid question... does the type of wood make a difference, ( oak, mdf osb) with sound or does the wood just make the building cheaper
You are a gift brother I've learned a lot of thing's thankyou for keeping it clean.
Great work as always. I was gonna bust your balls on using the miter sled and fence at the same time then noticed your little trick. Very nice! You show off good saw practice.
I applaud you for cutting up that wood like that, you may be better than my pops...maybe)
Master of the craft
Great video, but can this work in a 2018 BMW 7 series with a Bowers & Wilkins factory sound system. Also, note that i have a spare tire package which i can remove to make more space. Thanks
I've been trying to shoe-horn in a 15" sub into a boat for weeks now. Trying to fit it under the helm where the factory sub was in it's "enclosure" which was neither sealed nor ported, and fiberglassed into the hull. I've made 2 sealed enclosures so far based on manufacturer's recommended volume and neither have been able to fit. For such a simple hobby, this shit sucks lol
Damn! Looks at that spotless shop! I didn't know such things existed.
I take pride in my work area, I know it's not macho man dirty but I believe a clean well organized shop is usually a sign of caring about the results of the finished product.
that foam jacket on the wire I've sean you use a few times it seams kinda big so much wouldnt you have to fiqure it in your volume displacement?
Do u recommend putting damping sheet like 2mm inside the sub box?
Like I said before I dont under3why you dont have millions of followers. Your videos are the blueprint for car audio
Thanks for you time. And dedication
Great looking box
I would like to see the router video. I plan on getting the Porter Cable router mentioned in one of your previous videos. I would definitely like to see some of the tricks and the bits that you use to fabricate your designs. Thanks for all of the incredible and helpful videos! Your videos are exactly what car audio fans are looking for..help and tips!
Your channel sparked my deep dive into speaker building
question a sealed box with that has a chamber divider for 2 12" subs in trunk, will it sound the same if you have 2 sealed boxes, one 12" sub in each box still in trunk?
I like the idea of using the wood grain material as a inlay to create a more dramatic look. Personally I'd rather see a piece of carbon fiber (even a piece of formica covered in some 3M faux carbon fiber vinyl). I just don't care for "natural" materials in obviously high tech modern vehicles. I'd prefer high tech or modern textiles or maybe a sheet of brushed or polished aluminum. Maybe with your logo created in a high gloss polish and the area around it brushed. I don't know, you were asking for opinions and that's Just mine. Keep up the great work and great tubes, looking forward to the next one.
What did you guys do before CNC machines!!!!? Watch this video. 🔥
I'd use the wood, as long as it goes with the vehicle interior "theme". Looking go so far!
What about a video of making a sub for a convertible like the E46? The sub could play through the ski hatch. Would like to see some like this.
I've been using a router table and trim router for only about 6 months and even now i keep seeing many different bits that i have no idea what i would do with them. I could also use some tips on different ways to use a router
Yes on router video, specifically flush trim bits please. Straight flute versus spiral, why and when to use one or the other, I've only been using straight. Also, what would you call that type of bit you used at 9:10?
Could you make a video about Box Rising? Thanks greetings
Serious question... in a 4 door pickup why are down firing subs under the back seat better that up firing subs?? What about a single forward firing? Wouldn't that be even better?
so im thinking about experimenting with a dual port bandpass enclosure... thoughts?
Your Builds are always great to watch...
What Make/Model is your Table Saw...?
this is quite a bit late after the vid was released, but have you ever built a custom box for a Nissan Frontier? I just installed a JL Audio C1 690 in the front and the C1 650x in the rear and haven't quite figured out what kind of sub or box to go with. What are your thoughts on this one?
I have 2 pioneer shallow mounts I’m gonna put under my seat haven’t installed yet but the boxes are sealed do you recommend a ported box or sealed for these speakers I like all music but also like deep bass when jamming to anything there’s not many vids that have comparison
Channeling some Chrisfix vibes with all the on screen pointing and hand gestures
how do you calculate the distance that the subwoofer needs to be from the floor?
I wish i had the eq and this talent to build stuff like this.. i need this for my 2017 gmc canyon crew cab
Are you going to make a router bit video
what happens if you carpet the inside of a subwoofer enclosure
Router video? Yes Please!
Brother....
What an excellent video!
I guarantee you so many people learned some new techniques, as well as the right techniques, from your descriptions and work.
Real quick, what bit that you used with your router to add some depth as you took away material for your speaker binding posts?
Thanks in advance and can't wait till the next video!
Seeing all those rings just gave me a crazy idea , what about a 8th order basscannon ?
Can you make a video on how to calculate air space and build a ported fiberglass enclosure? I have an 11 camaro ss and want to build a enclosure tucked into the side of the trunk space.
Tried cutting with my handheld router and a small bit yesterday, it jumped so much I used a chainsaw instead. I am serious.
I need to get a Bosch jigsaw.
I would love for you to explain how the upwards firing router works and is assembled.
Need this for home system
could you make some comparison between sealed box and passive radiator subwoofer?
I would like to see you do a sub enclosure for a 5th Gen 4Runner. Your layered box you made for the Jeep turned out great, but I wonder if you could show us another solution that may be different. I had a custom fiberglass box in my older 4Runner and loved it, but that was a long time ago. I'm curious about a setup with 3 or 4 8" woofers, or maybe using shallow mount 10's could leave you with more options to make a box that is better hidden.
Help!!! I have 2 Memphis 12s in a enclosed down fire qbomb probox and the excursion is too great and it is rubbing or hitting my floor mats…. What could I do to correct this issue?
Could you give a guide on how far off the floor a downward firing sub should be spaced. I know you can get gains and losses depending on how close they are.
You should make a video making a box with just everyday tools rather then expensive tools that most people don’t buy.
I've done that several times. No one watches.
I wouldn’t mind watching.
Ive always pushed JLs all my live for the passed 18 years but right now im pushing 2 13.5 jlw3v4 what box and dimensions do you recommend. I would really appreciate it
Good god your cuts are so perfect. Beautiful box.
I just pick a set of kicker lt7s shallow subs 12s n there r going b hind the seat of a 03 silverado single cab i need two boxes one for each side so i can move up n down the center consul thers about 22 wide n 16 high n 7-8 deep u have a diagram for the boxes can u make it to kicker seald specs thanks
Do you have plans for a Gen 5 camaro convertible box that can house 2 10" JL 10tw3 shallow subs. If not, what would you charge to make them?
Hello, can the same plan be applied with Pioneer's TS-W311D4 12" sub-woofer?
Router video please...... and thank you I learn a lot watching this channel
Looking for some advice. I just got two 2000 pyle 15's I have a 2000w amp for each sub "both in the same box with separate inputs but each speaker has 2 inputs how do I wire them
Hello, I was wondering what would be the best box ( ported or sealed ) for a 2016 Chevy colorado extra cab 4 door. And would you have a design for that. I have searched your site and did not find anything. I need an under the rear seat down fire box for a jl audio shallow mount tw3. Thanks for your help
What’s the size of your workspace, before you started adding cabinets and toys?
I'd be up for that router video. Just picked up a Bosche router with table but have yet to use it very much.
Also any thoughts on a quick disconnect subwoofer? For example, I know several people who are hesitant on getting a sub installed as it takes up a permanent spot in their trunk. It would be awesome if there was a way to make a quick disconnect subwoofer that can be removed in seconds and without tools. This would be for people who have a limited trunk space but don't want to compromise for a sub, for say like a road trip or when they really need to use all of their trunk space
Another video that might be great would be best ways to secure subs in the trunk, especially for people who don't want to drill a sub into their car or make any other permanent modification.
I know this isn’t really your area but could you possibly do a center console build with speakers inside? I can’t find anything on making a custom console or any piece that’s as thorough as you.
Is the downfiring setup in a sedan going to reduce output compared to rear firing ? Doing 1 skar 10 ( cause im poor) also stock electrical.
me 2 brother ima big fan been watching your channel for years i was trying to see what brand is your plate earlier 😅 on a different video of yours but since you mentioned it yes i would love to see all those router tools
Great video! Just wanted to ask, which wiring configuration are you using? I have two exact subs but 12” and just wanted to know how to wire them properly. I have a jl audio hd750/1 mono amp too
Hola amigo, tengo el 10tw3 como puedo obtener las medidas de el cajón de tu video, qué por cierto excelente trabajo.