Finally someone made great tutorial! Thank you for this so much! Btw those bmw douple M52 catalytic converters are worth 800€ 😏 I have sold couple for the catalytic recycle places.
Going from memory here, but I'll tell you how I did it with my old E36 328i, as I didn't touch anything in the DME (ECU) for it. Take the stock muffler off the back. Cut the top off it above the seam, it takes a bit of work as there are a couple of plates running vertically that are spot welded top and bottom. Inside you'll see some packing material, once that's removed you'll find I think 6 pipes that have holes all through them, cut them out along with the two vertical plates. Two of those pipes are smaller in diameter than the rest, discard them. I then took the other perforated pipes and sort of welded them inside the muffler where I could, to join the inlet and outlets of the muffler together. Weld the top back on, and make sure it's sealed up. After that, I got a much improved note from the exhaust, no drone, no need to remove resonators or cats, yet lots of popping and banging from the exhaust on deceleration, without tuning. And from beneath, it looks exactly like a stock muffler, perfect if your car gets checked often. Total time to do it again for me would be around 1 1/2 hours, only costs are cutting and welding consumables.
With stock ECU file, even without a muffler you should not have any pop and bangs going out of your exhaust. Especially with CATs still installed. It is tested several times. Most likely you had some kind of mixture related problem.
@@crank3646 Interesting that you say that. The only other variables was an M50 manifold swap and it was originally an auto that I swapped to manual. So maybe the fuel overrun mapping on the auto is different? As a friends E36 rally car, with the same mods but straight piped, no tuning, was also doing it.
Nice work! Thank you for your videos of ms41 are very helpful. Are you planing to install the 540i MAF to try to get some more air into the engine? Would be nice to have a video of the installation and mapping for this mod.
Thanks! 540i MAF is required if you go forced induction or using some crazy cam specs + stage 2 or 3 ported cylinder head. With my setup, I'm still far away from using my full potential of my stock MAF.
Thats great video . A while ago some 1 had a video on how to do the fast Rev limit and launch control and how to make it but they took the video down . I remember he changed a bunch of the Rev limit stuff to around 3000 rpm but that's all I really remember
Hello! I did the same for my ms41.0 ECU, but I uploaded the firmware to the unit via "ms41 flashtools". After loading the dump it gives something like “4 checksums needed correction”. how to correct this checksum? or do I really need quickflash 2.0?
Hello @Crank , I have a question. I buy the car with this pops mode and i want to remove it. I download all the program download ecu from the car and rewrite all this file to stock one. But when i try to write it (flash) i have error “error preparing ecu. please try resetting ecu for 10 seconds” I Have 12v on pin 14 and make a bridge to 18 but still give me this error. Only thing i know is previous owner change the ecu and this is not the original one but the code of the ecu is not of the list of ecu which is not flashable. And on pin 60 on the ecu there is 12v from the bridge Do you have any idea. Thank in advance
Hi. First run in the morning AFR poor around 16. Engine stroker 3.0 m50. Ms41. After warming up, afr is normal. But until the water warms up, the afr is in the 15-16 range. After warm-up, idle 13.9 acceleration in driving mode and 12.7 at full load. So the problem is only in the cold engine in the morning. All sensors and elements are robust. No fault logs. Can you help. I use Romraider
Hello Crank! I watched all your videos on MS41 tuning. It looks very easy in the video, but in real life, it doesn't work. ROMRAIDER shows that MS41 does not match the definition and therefore cannot do anything. I'm trying to find a lot of forums, but nothing. Maybe you can throw in a link where you can get definition files MS41? If you could, that would be very nice.
hey man, i followed the changes you made on the map, the pops start at 3k but if i accelerate to about 5k and take my foot off the accelerator they only start doing around 3k and take a while to start, you know what it can be? My ecu is ms41 do you know how to activate launch on it?
Hi! First of all thanks for your work!! Let me ask one question, Your stock fuel base and ignition maps are way different than my “stocks” files…any reason ??
Great video crank. I have a 1999 e36 328is US model and did the fast rev limiter from your other video and it worked great. Now I did the exact same thing from this video pops & bang and using same software as you do, opened ms41 quickflash and flashed it, waited about 15 seconds, stared the car and tried it Nothing Happened just fast rev limiter. What could be the problem. Thanks
Hello Crank , Once again a most enjoyable video to watch your expertise on changing the tune of your BMW , and a special shout for Pete and his welding skills , that would have taken him a long time but nonetheless a great job , Pete could teach us all how to weld stainless steel , more videos , more subs Crank food for thought my friend , like the more varying content the more interest gained from youtube viewers...Thanks Crank and all others that help for these great videos , keep them coming..One question - What will you do when all cars are electric? :D lol
Thanks Peter! Actually the varying content is confusing/annoying for my subscribers. Most of them subscribed to my channel because of the BMW repair videos and when I work on, lets say Subaru nobody wants to watch it. But it is ok, the amount of views that I get is plenty enough for me :) Electrical cars... ye... they will bring a lot more work for me, for sure. From diagnostic point of view.
Hey broo thanks for that someone want to show us this deep knowledge, i have question, i want to start do smth with my ecu i m44 but idk how to start xD can u tell me where can i dowland demo software any kind of engine it can be a r4 or r6 i want just do smth on my pc with this, for exaple change ignition map etc xDd thanks for replying :DDDDDDD
Имам M50B20tu 1 Vanos и ако не се лъжа инсталацията е на SIEMENS MS40.1, има ли как да направя бърз прекъсвач и като цяло мога ли да направя нещо с компютъра на колата? Свалил съм я RomRaider програмата, но не откривам writer за SIEMENS MS40.1. Какъв writer да използвам за този компютър? Ще ти бъда много благодарен ако знаеш нещо по въпроса :)
THATS A VERY GOOD TUTORIAL MAN. Thankyou for being a good person for us beginners XD
i have been waiting so long for this vid
You are welcome :D
Thanks for explaining in detail. 👍
Finally someone made great tutorial! Thank you for this so much! Btw those bmw douple M52 catalytic converters are worth 800€ 😏 I have sold couple for the catalytic recycle places.
Thanks to the values it works perfectly with popcorn.
Go straight to the point when making such videos 🙏🙏
hi thank you for this video plz can you share the blue cable detalis that you used to connect the laptop to your ECU
Going from memory here, but I'll tell you how I did it with my old E36 328i, as I didn't touch anything in the DME (ECU) for it. Take the stock muffler off the back. Cut the top off it above the seam, it takes a bit of work as there are a couple of plates running vertically that are spot welded top and bottom. Inside you'll see some packing material, once that's removed you'll find I think 6 pipes that have holes all through them, cut them out along with the two vertical plates. Two of those pipes are smaller in diameter than the rest, discard them. I then took the other perforated pipes and sort of welded them inside the muffler where I could, to join the inlet and outlets of the muffler together. Weld the top back on, and make sure it's sealed up. After that, I got a much improved note from the exhaust, no drone, no need to remove resonators or cats, yet lots of popping and banging from the exhaust on deceleration, without tuning. And from beneath, it looks exactly like a stock muffler, perfect if your car gets checked often. Total time to do it again for me would be around 1 1/2 hours, only costs are cutting and welding consumables.
With stock ECU file, even without a muffler you should not have any pop and bangs going out of your exhaust. Especially with CATs still installed. It is tested several times. Most likely you had some kind of mixture related problem.
@@crank3646 Interesting that you say that. The only other variables was an M50 manifold swap and it was originally an auto that I swapped to manual. So maybe the fuel overrun mapping on the auto is different? As a friends E36 rally car, with the same mods but straight piped, no tuning, was also doing it.
@@crank3646mine pops and bangs with no tune and just a muffler delete 2nd gear 4k rpm let off and just keep tapping the throttle 🤷🏽♂️
@@shauno4405 same
Nice work! Thank you for your videos of ms41 are very helpful. Are you planing to install the 540i MAF to try to get some more air into the engine? Would be nice to have a video of the installation and mapping for this mod.
Thanks! 540i MAF is required if you go forced induction or using some crazy cam specs + stage 2 or 3 ported cylinder head. With my setup, I'm still far away from using my full potential of my stock MAF.
my Lord that sounds soo good.
Thanks Man, i did exactly the same u did and its awesome!!! Im very happy, thanks bro
Thats great video . A while ago some 1 had a video on how to do the fast Rev limit and launch control and how to make it but they took the video down . I remember he changed a bunch of the Rev limit stuff to around 3000 rpm but that's all I really remember
It is not so hard, but you going to need to change your software to MS 41.2 to do it
Hello, you dont need any mappack ornsomething to load all those Maps? When u open the .bin you have all the Maps?
Thanks going to try this !
Good video but do you know anything about if this chance to ecu will work on my e39 1998 with cat delete and 2mufflers coming out of the back?
The exhaust sounds mint! 🤜
i have a question about the female 20 pin to the obd. i jumped 2 of the pins to allow the write but they sparked. what am i to do?
I dont have all the same options as you do. how do i get all the folders u have? i could only change ingition table and fuel table.
Very nice guys! Dutch regards, Nico.
Thanks Nico !
hello from Latvia. Great video. Nice :) 😏
Czy jest możliwość włączenia napisów ? Jestem z Polski i nie znam twojego języka . Dziękuję i Pozdrawiam
Great vid! Popping content!
Super video!
Wow efficace B28 💥💥💥💥
Sounds great
Hello!
I did the same for my ms41.0 ECU, but I uploaded the firmware to the unit via "ms41 flashtools". After loading the dump it gives something like “4 checksums needed correction”.
how to correct this checksum? or do I really need quickflash 2.0?
Hello @Crank , I have a question. I buy the car with this pops mode and i want to remove it. I download all the program download ecu from the car and rewrite all this file to stock one. But when i try to write it (flash) i have error “error preparing ecu. please try resetting ecu for 10 seconds” I Have 12v on pin 14 and make a bridge to 18 but still give me this error. Only thing i know is previous owner change the ecu and this is not the original one but the code of the ecu is not of the list of ecu which is not flashable. And on pin 60 on the ecu there is 12v from the bridge Do you have any idea. Thank in advance
The exhaust system looks very good. What is the thickness of the stainless steel pipes you used ?
Thanks! 1.5 mm
Hello. advice how to make popcorn on e36 on m52b20. Tried to do what you want, didn't work very well. Can you help?
Hi. First run in the morning AFR poor around 16. Engine stroker 3.0 m50. Ms41. After warming up, afr is normal. But until the water warms up, the afr is in the 15-16 range. After warm-up, idle 13.9 acceleration in driving mode and 12.7 at full load. So the problem is only in the cold engine in the morning. All sensors and elements are robust. No fault logs. Can you help. I use Romraider
а може ли да се направи напримерно само с включването на климатика или парното да има бангове и като е изключен да няма
It's just for 328i?Can on 318i?
Hello Crank!
I watched all your videos on MS41 tuning. It looks very easy in the video, but in real life, it doesn't work.
ROMRAIDER shows that MS41 does not match the definition and therefore cannot do anything. I'm trying to find a lot of forums, but nothing. Maybe you can throw in a link where you can get definition files MS41? If you could, that would be very nice.
bro you re the best
thank you
Thank you for another good video!
Thanks nemanja!
@@crank3646 Hi, I'm from Russia myself, nice to meet you. can I ask a couple of questions about this video?
Thank you, brother, for this beautiful explanation. Can I, before I start work, save a copy for my car's computer before starting to modify it♥
Yes, you can
@@crank3646 Can I work in a program? tuner pro
Boa noite gostaria de saber qual programa para poder fazer aqui no Brasil ativa a legenda por favor
Thnx bro ❤ you make my day
hey man, i followed the changes you made on the map, the pops start at 3k but if i accelerate to about 5k and take my foot off the accelerator they only start doing around 3k and take a while to start, you know what it can be? My ecu is ms41 do you know how to activate launch on it?
Hi! First of all thanks for your work!! Let me ask one question, Your stock fuel base and ignition maps are way different than my “stocks” files…any reason ??
Randomly rechecking your videos I saw my coment and still guessing the reason hahaha
Thanks for your work !
Depends on the engine cylinder capacity
Can you give us the link for this tune
Dumb question? But does this adjustment work on the m52b25 since being different ratings?
What Programm is this!
. I tried with ECM but doesn't work
You are Legend !!!
could anyone tell me how to set it to turn on with AC ?
Здравей, на м50б20 ванус бърз прекъсва има ли как да се направи ?
Hi, I'm from Russia myself, nice to meet you. can I ask a couple of questions about this video?
Can i make it in m42 318i bosch???
Great video crank. I have a 1999 e36 328is US model and did the fast rev limiter from your other video and it worked great. Now I did the exact same thing from this video pops & bang and using same software as you do, opened ms41 quickflash and flashed it, waited about 15 seconds, stared the car and tried it Nothing Happened just fast rev limiter. What could be the problem. Thanks
Wrong software version maybe. Or maybe car was too cold, do you have original exhaust or catless?
Hey man nice exhaust! I took a look at your ignition map what is max load you get with such 328i ? And what ignition you run at WOT 28-30* ?
Thanks! I believe it was somewhere ~ 630. The ignition should be visible in the video.
Dear sir thank you clear training UA-cam
Hello Crank , Once again a most enjoyable video to watch your expertise on changing the tune of your BMW , and a special shout for Pete and his welding skills , that would have taken him a long time but nonetheless a great job , Pete could teach us all how to weld stainless steel , more videos , more subs Crank food for thought my friend , like the more varying content the more interest gained from youtube viewers...Thanks Crank and all others that help for these great videos , keep them coming..One question - What will you do when all cars are electric? :D lol
Thanks Peter! Actually the varying content is confusing/annoying for my subscribers. Most of them subscribed to my channel because of the BMW repair videos and when I work on, lets say Subaru nobody wants to watch it. But it is ok, the amount of views that I get is plenty enough for me :)
Electrical cars... ye... they will bring a lot more work for me, for sure. From diagnostic point of view.
Страхотен клип ако знаех какво трябва да се направи преди да сложа пуканките нямаше да съм със едно гърне назад ;)
Мерси!
For m52b20 is the same?
Pretty much
ooh there is nissan silvia s12 outside?????? i had that models before (nostalgic)
Yes, good observation :)
good. ms43 can you show? pops/bangs
There's forums about that ecu
Can anyone possibly point me in the right direction for ms45.1.... i can do ms41,42,43 but 45 is throwing me for a loop
just for fuel map and timing map/decel
what is fuel restoration ?
v burgas li se namira serviza
Wow i just commented this earlier! 🤣 need this.
Yes just saw it, but decided to hold my answer :D
Супер , но може ли да кажеш на колко милиметра са двете тръби на генерацията (питам за м52б23)
Тръбите са същия диаметър като оригиналните, мисля че беше 50 или 55мм, забравих колко точно
You can share your ori file and rr defenitions file
Брато ако чипосвам компа на м52б25 със комп от б28 ще има ли промяна в вървежа
Да, в негативен план
Hey broo thanks for that someone want to show us this deep knowledge, i have question, i want to start do smth with my ecu i m44 but idk how to start xD can u tell me where can i dowland demo software any kind of engine it can be a r4 or r6 i want just do smth on my pc with this, for exaple change ignition map etc xDd thanks for replying :DDDDDDD
M44 engines have different ECU from MS41, which does not have a tuning platform like this one, so it is going to be much much more harder for you.
личи си че си българин :D
Имам M50B20tu 1 Vanos и ако не се лъжа инсталацията е на SIEMENS MS40.1, има ли как да направя бърз прекъсвач и като цяло мога ли да направя нещо с компютъра на колата? Свалил съм я RomRaider програмата, но не откривам writer за SIEMENS MS40.1. Какъв writer да използвам за този компютър? Ще ти бъда много благодарен ако знаеш нещо по въпроса :)
Никой не е направил дефиниций за 40.1. По добре мини към 41
33:35
The catalyst is worth it ~600$. Platinium Bro
Здравей може ли някой път да направиш видео и с бг версия супер попкорн стана
those cats go for 500plus in uk, its like seeing money thrown away lol
Who said that I didn't sell them
Тва до колко е вредно за мотора?
👍😎
Ще мое ли да го направите и на моята кола?
Can you upload somewhere this bin? I will try it on my 328
It is not a good idea. The file is with modified ignition and vanos tables. It is not clearly only for sound effects
@@crank3646 but still.. I tried make pops and bangs for my 328, but all i could get was a little rev hang and unburned fuel smell😅 cats are deleted
Къде е сервиза в Бургас
5-ти км
Може ли някакъв телефон за връзка
@@mihailminkov4092 Под всяко видео, има координати за връзка с нас
Kъде се намираш в бургас
Чувак . Более дикого русского акцента я не видел😅😅
Hi bro 💙
Love you from iraq.
Do you have a instgram
Hello Gayth! No I don't have instagram
"mUFUOR" hahahah
Голям си! :)
Wan tawzand
Katalik konvirtirz
mofor = muffler
Дай прошивку для m52b28 😅 тоже так хочу на е39
Здравей гледам че си от бургас може ли твой фейсбук да се свържа с тебе да ми ремапнеш 20ката м50 б20 ванос
Any way of doing it to a 4cyl e36?
Did you ever rechip your ecu if so what did you use .