DC Voltage and current Adjustable Power supply, DIY DC voltage controller
Вставка
- Опубліковано 2 сер 2023
- DC voltage and current adjustable power supply, DIY dc voltage controller.
This is a dc voltage controller simple DIY using a 2sc5200 transistor. This is a basic voltage and current adjustable power supply. But not a powerful dc voltage controller. You can supply an input maximum of 200V, 15A.
Components used in this project:-
1. 2SC5200
2. 47 Ohm 2W
3. 0.22 Ohm 5W Resistor
4. 10k Potentiometer
5. 10 Ohm 2W
6. 5A Diode
#voltagecontroller
#homemade101
#highcurrent
#Adjustable_power_supply
#voltagecontrollerdiy
#adjustablepowersupply
Make inverter 👉 ua-cam.com/video/Rbvt53TiWtI/v-deo.html
The transistor ? - You used in the above video was a TTC2500 VCE = 230V 15A
Can i use that as a short killer...?
lovely
Sorry, I have gotten all the other electrical components for this project, but, it remaining the TTC5200 transistor which I couldn't get. Please, what other transistor can I get in replacement of the TTC5200 transistor and still get the same outcome?
Thanks for your reply.
Parabéns.
Esse é confiável.
muitas felicidades.
Parabéns!!! Ótima explicação!!!!
welcome
Nice video, well done, thanks for sharing :)
Welcome 🌎
Рисуй всегда электрическую принципиальную схему чтобы понимать все важные узлы
OK I will try.
Вони цього зачасту не роблять.
Great, to remember how I taught students what voltage is and what amperes of current is 😊.
So true!
Tem proteção contra curto circuito na saída?
Tambien que se podria mejorar usando otro transistor para hacer un darlignton por la corriente de salida
This is really very good Thanks you so much sir
Most welcome
Can you be a regulator on a motorbike? , plus input diode
TRANKS YOU SOU MUCH🇧🇷🇧🇷👏👏👍👍
Welcome bro
MANO VOU REPLICAR PRA CONTROLAR O MOTOR DE IMPRESORA E O MICROONDAS E GERAR SENOIDE NOS IRF TENHO QUE TER 15V AC NOS G DE CADA IRF 👏👏👏👍👍👍👍🇧🇷🇧🇷
Parece bom, vou montar!!
Hello, Can this circuit charge some capacitors? for example 200v per 1000 uF?
Rất tuyệt vời mạch điều chỉnh điện áp
cảm ơn người anh em.
Exelent! JOB WELL DONE.
Thank you! Cheers!
¡¡ G R A C I A S !! ✨
thanks
Bạn làm con biến chỉnh vặn thuận chiều luôn chứ sao bạn làm toàn vặn ngược chiều Kim Đồng hồ vậy bạn ơi , lỡ làm thì làm cho nó đúng luôn đi
Kohlepotentiometer werden durch Kühlkörper erhitzt! Diese haben starken Temperaturkoeffizient. Daher instabile Spannung und Strom...
Amazing circuit : few Elements connected without board ..and variable voltage , ampere..nice work..thanx100🌹
Thanks and welcome
Very Good for you. Thanks You and Have a Good Nice Day My Friend ❤❤❤
Have a nice day
Very nice and interesting. Thanks very much. This could b more easy if u could provide circuit diagram of each video.
ok bro.. welcome
Parece muito útil, mas tenho dúvidas: o diagrama que aparece no princípio do vídeo é diferente, pois o negativo vai direto à carga, e, se eu ligar em voltímetro/amperímetro, como serão as ligações? Uma dica: se possível, coloque os potenciômetros trabalhando para o mesmo sentido. Saudações do Brasil.
welcome bro
Chỉnh áp kiểu tuyến tính nầy khi chạy áp thấp nó nóng transistor kinh khủng. Nếu chạy áp cao thì bình thường, không bằng cách chỉnh duty (độ rộng xung)
разница в напряжении будет превращаться в тепло, допустим 100в 1а превратить в 5в 1а будет 95вт
yes possible
Закон Ломоносова ни кто не оьменял еще.
is the 5w 0.22ohm resistor minus the current?
can we make without the 5w resistor in the output?
It would be really helpful IF you provided a schematic. Why did you not think of that?
sorry
Esquema para hacer algo tan elemental ?
@@homemade_101 ... No se disculpe, el que quiera el diagrama... Que lo Haga !!
Well laid out circuit ! ... but .... like a LOT of these videos , a CIRCUIT DIAGRAM would be a great help for those wishing to construct in a different way ( or modify ) ........ DAVE™🛑
ok I will upload
Can i supply this 100v?
For how long this circuit can support an instrument running continuously with 5 amps ?
Thank you so much
Welcome bro..😇
If you try and supply a load with 15A from this supply the 0.22 ohm 5 watt resistor you have in series with the output will be destroyed very quickly!
That heatsink is severely undersized.
Ola...pode usar qualquer transistor com essa configuração se nao tiver esse do video?
yes you can
Buenas. Tengo que decir que el control de corriente esta mal conectado UNO de sus terminales. La resistencia de 10 ohm, no debe ir a negativo . Debe ir a la salida luego de la resistencia de .22 ohm 5W y tal vez no necesites el diodo para lograr una menor corriente minima de salida
Hello, very interesting. How to make the voltage change more progressive ? Does it reduce the current or it is a current limiter ? Thanks.
It is depend transistor. 2SC5200 maximum 200V, 15A
I made this module and it works. But I'm interested in what to do with the potentiometer for voltage regulation because it raises the temperature? Should I install the same 10k but 3 W.? Otherwise, it works well at voltages up to 50 V and the temperature is within normal limits, but at higher voltages it heats up.
It all depend on what you are going to use this circuit for, if it for any kind of lab power-supply then forget this construction, there is nothing in it that is stable in any way, it is a extreme crude way to regulate voltage and current without any feedback or stabilization. Nothing will stay the same if the input voltage change.
It is just a demo circuit to show how to use a transistor as a regulator. It has it's usage, bench power supply is not one of them.
@@K2teknik. ok dear but you should make a video with feedback section and stabilization 😊😊
При 100V транзистор может пропускать только 0,3A
At 100V the transistor can only pass 0.3A.
How can change connection for clockwise
Its working Anty Clock wise for voltage and current increase
Won’t the hot glue melt when the heatsink gets hot from the transistor?
yes hot
We use any of ampere mosfet its a choice or not please answer my question i made it ?
I like your video❤❤
thank you bro..
Wow 💯👌 really super vedio ...thanks for sharing this 😎🙏
Welcome
Sir namaste
Supply battery charger me use kar sakte hai plz reply
Nice video,but have not shown the current in multimeter that it is going up and down
sorry
this is good but 3A. ua-cam.com/video/vUOBuOsQ_0g/v-deo.htmlsi=Ag1gI8vAgtscbdix
When i see those guys doing electronics like that i go nuts put it in an enclosure
🙄
Input can be 15A DC, but how much watts those potentiometers can handle? For a medium size project, they need to be 10 watts at least.. Good project, but limited usability.
Smoke Machine! 100Vin, 1V 20A out = 1980 watts burning the transistor (150W package) on a 5W heatsink, pure rubbish claims.
Zaten 24 to 12, 80amp düşürücü 250€ böyle kolay olsaydı😂
Added short circuit protection is better....
yes
Can we get constant current output, if load increase also need 100mA constant current
🤔
👍👍
You must add voltmeter and ammeter
yes
Sarannya dong,..Bagaimana untuk mendapatkan lebih dari 20amper??
10A
I think that switch mode is better.
🤔
It is a emitter follower .
Every thing moves with output load & input voltage variations !
ZERO voltage regulation & no current monitoring ( it clamps the base drive voltage ) .
PS
The 47 R & 10 k voltage pot are toasting nicely !
जबर दस्त सर जी,क्या इसमें वाल्ट और एम्पियर कंबाइंड वाला डिजिटल मित्र लगा सकते है।बाईटरी चार्ज करने के लिए।
yes but not have an auto cutoff part.
@@homemade_101 मतलब सर
I have a question, with your homemade DIY DC voltage controller. My power supply is lithium battery cells 4S4P 40A (my BMS is for a 4S 40A). With your homemade DC voltage controller can i have a constant voltage to 12V (and 20A is enough) whereas my battery cells will decrease little by little its voltage ?
How could i make this handle 20 amps and 1200 watts. Can i use multiple transiters to do this? and use a 20amp diode instead? Your video says it will only do 15amps and the manufacture specs on the transistor says 150watts. Thank you for any help.
yes it is depend transistors
Why not build a circuit board from cardboard and copper wire flattened out? The copper wire could be drilled as well as connected firmly to the cardboard.
because this is an Experiment.
I want max 300 volt and 30 ampere controller for my solar 2 string in parallel. what can i do for circuit 🤔
Which circuit should we use to adjust 12v.6 volt 10a:
🤔
I'd like very mutch to get the schematic of this circuit . . .
Ok i will try other videos
Berapa amper maksimum input dan outputnya
Congratulations but Where's the electric scheme,tank you
I already tried this, fed 60-80v for input then my potentiometer glowing..😁, better u tried this for the worst case..
some time
Warning: This circuit does not work at high loads. The negative line passes through the variable resistor and it has a weak current. There is a big trick. This circuit may appear to work well on the measuring device. Just notice that the lamp lights up strongly when the resistance is raised and does not scale correctly.
Muy buen video mi pregunta es con una fuente atx de pc 500w podria con el elevador cargar baterias de coche a 14v o tendria que poner al gun diodo y para baterias 3s 18650litio también valdria? Gracias un saludo Valencia (España
3s 18650 OK. But not have auto cutoff.
Como podriA hacer el corte automatico
El bms no cortaria
Hi bro ,kannst du auch eine effektive batterie ladengerät fur Auto batterie 🔋?
yes, but this circuit is not recommend.
How many watts is your soldering iron?
35W
it’s going to get extremely warm and you used hot glue to attach the potentiometers, your better choice would’ve been an epoxy
yes this is an experiment. you can apply any other metered.
Will voltage remain constant when changing current.
🤔
Very good sir to Good
Welcome bro ✨️
Die beiden POTIS brennen immer wieder durch. Wieviel Watt müssen de denn haben ?
Can i use 6 Amp diode instant of 5 amp?
yes
Nice
Can I change Transistor to control 300V-15A?
max voltage is 230v
Нельзя подключать резистор 2 ватт и потенциометр последовательно. Потенциометр тогда должен быть тоже 2 ватт, а не обычный❗
What is the output ampere
What is max DC input voltage, like 30v 60v 90v 120v???
60V ok
How do you set the current to a known value?
🤔
That's a good question.
The circuit is a starting point for future development, you need to draw the schematic on paper or into a circuit simulator and add/modify to your needs.
Some knowledge about Ohm's law will come in very handy.
The circuit as is do not regulate the output current with any kind of feedback, it only regulate the base current to the power transistor and you can't really calculate/predict the current because other factors like hfe of the power transistor is not a fixed value it depend on collector current and temperature, so to set a known value and keep it stable you will need a feedback loop, an op-amp will come in nicely here.
@@K2teknik.Dear you must make a video same project with feedback and stabilization 😊😊
सर जी ये उल्टा घूमने पर वोल्टेज बड़ता है क्या सीधा नहीं हो सकता है
Can this project be used to charge 12v car battery?
yes
Keren lurrrrr
Can i give input supply 100v 30 amp in this circuit ?
Hi, why don't work potentiometer current volume?I change it, the current remains constant
try this is : ua-cam.com/video/9vWsRIokOIk/v-deo.htmlsi=Q04ZFxMZgk4m7T-j
@@homemade_101 don't work this too
It's best
Hello...
Can it be used continuously as 90V 20A INPUT - 60V 14A OUTPUT?
yes 60V
are you sure about this?
Can it be used continuously as
90V 20A INPUT
60V 14A OUTPUT?@@homemade_101
If the circuit is not yours and you have not tested it
Can you send me the original link of the video?@@homemade_101
@@homemade_101NO!!Максимальная рассеиваемая мощность 100вт.(90-60)•14= 420вт!
So what you have is a supply of maximum 90V 20A, and you want to set the circuit to archive 60V 14A at the output ?
That gives you 30V of voltage drop over the power transistor and this at 14A, that result in about 420 Watt displace in the power transistor, 150 Watt is the maximum power the power transistor can handle, so this circuit, as is, can not be used in these conditions.
Be attentive regarding the answer you got reading "yes 60V", it do NOT take your request regarding 14A into account, otherwise the answer is right.
This circuit is just a demonstration of a serial regulation with voltage and ampere adjustment where a power transistor with some, at face value, impressive parameters is used, if you feed it with the maximum input of the suggested 200 Volt and 15 Ampere you got a potential person killer and source for fire, so be careful it is not a harmless toy.
how much current did the input voltage?
maximum current and voltage 100V, 8A
ok, thanks
How 2 maximum input voltage supply sir ?😮
100V DC
Hasilnya ko min bukan plus
Please, what is the minimum and maximum output of this circuit both the voltage and the ampere? 🙏
20v , 5A
@@homemade_101 Sorry, I have gotten all the other electrical components for this project, but, it remaining the TTC5200 transistor which I couldn't get. Please, what other transistor can I get in replacement of the TTC5200 transistor and still get the same outcome?
Thanks for your reply.
Agr input 12 V , 2 A ho to output kya hoga ?
max out 12V, 2A
maximum input voltage 200 volt haaa !! Let's try and watch...
sorrry
Minimum input limit ? How much volt and ampere ?
30V 5A
Can provide 20v ?
yes
can for batry charge brother ?
yes. but not auto cut off protection
wokey bro
So how much Ah output is this???
15A
I seem like ur 47ohm resistor is getting burn
no no it is mistake. it is not burn.
Qual a voltagem e amperagem maxima de saida?????
30V 5A
Super sir iam ur fan How to connect digital volt meter and fan...Thank u
potentiometer reverse connected..
🤔
Una bombilla de 12 volt 2 amp en 20 seg cocina el transistor. puro cuentos.
Can I charge my electric scooter
lithium fero phosphate battery
48 volt 24 ah
no. this is experiment only.
Super super super 👍👍🙏🔥💯
enjoy
لا نرى نهاية الاسلاك
16V Supply IN DC
thank you@@homemade_101