Acura / Honda Transmission Problem? Blinking D? Check here!
Вставка
- Опубліковано 24 жов 2016
- Hello youtube!
Are you guys having a transmission problem? You have a blinking D? Your speedometer does not work anymore or malfunctions sometimes? You have a check engine light? Your automatic gears are stuck? You cannot manual shift? Well hopefully, you have a small problem like me! I thought my transmission was finished until i used my OBD 2 READER and read two codes : P0722 : Output Speed SEnsor No Signal and P0723 Output Speed Sensor Malfunction. Luckily, this could mean that your output sensor has a electrical problem. It could be Input Speed Sensor too. If you've never touched the engine bay, it could be that the sensor just died or the connector cannot bring proper signals back to the ECU.
In this video, i show you the location of both Input and Output Speed Sensor. I had 4 symptoms : Check Engine, Flashing/Blinking D , Speedometer no longer works and Stuck Gears. If you really want to drive your car because you have no other means of transportation, simply disconnect the sensor you're having problem with and your car will work. It's just the gears will be shifted rough and in more delay.
►If you want a good ABS / SRS / CHECK ENGINE reader instead of reading flashing lights, nothing beats Autel. Only 100$ on Amazon , amzn.to/2jnEPJk
Record the number of long blinks followed by the short blinks for your D light. Then do the same for your Check Engine light. Here's an example : "In my case I had code 27 on the D light. That was 2 long blinks followed by 7 short blinks. Then I had code 70 on the check engine light. That is 7 long blinks and no short blinks."
5 - Transmission range switch (multiple shift-position input)
6 - Transmission range switch (open)
28 - ATF temperature sensor (range/performance, short, or open)
15 - Input shaft (mainshaft) speed sensor (range/performance, intermittent failure)
9 - Output shaft (countershaft) speed sensor (range/performance, no signal input, intermittent failure)
64 - 1st, 2nd, 3rd, 4th or 5th gear incorrect ratio
40 - Torque converter clutch circuit performance or stuck off
76 - AT clutch pressure control solenoid valve stuck (ON, OFF)
70 - Shift solenoid valve A stuck (ON, OFF)
71 - Shift solenoid valve B stuck (ON, OFF)
72 - Shift solenoid valve C stuck (ON, OFF)
77 - A/T clutch pressure control solenoid valve B stuck (ON, OFF)
45 - Shift control system
24 - Transmission gear selection switch upshift or downshift switch (short or stuck ON)
26 - 3rd clutch transmission fluid pressure switch (short/ON, open/OFF)
27 - 4th clutch transmission fluid pressure switch (short/ON, open/OFF)
24 - Transmission gear selection switch (short/ON, open/OFF)
16 - A/T clutch pressure control solenoid valve A
23 - A/T clutch pressure control solenoid valve B
29 - A/T clutch pressure control solenoid valve C
7 - Shift solenoid valve A (short, open)
8 - Shift solenoid valve B (short, open)
22 - Shift solenoid valve C (short, open)
1 - Torque converter clutch solenoid valve (short, open)
►Please Subscribe if you want more Modified Cars from Montreal or to see some of my DIY's :) - Авто та транспорт
![Blinking D [ P0843 07 Honda Crv ]](/img/n.gif)
Thank you so much for sharing this valuable information. I'm having the same problem right now and I hope this information will help. Thanks again.
Good Job man!! Keep up the great videos! You helped me out a lot! Honda/Acura fanatic!
Thanks so much for the info. I just had this problem this am. Keep those videos going. Your helping a lot of people.
Thanks so much for sharing this. It was a great help.
Great job body thanks for sharing sounds exactly like the problem I'm experiencing with my acura vehicle... thanks for such a great help info again.
Hey I'll look into this. Thank you for the video!
“With the D”!!! XD
Good vid man, good info
Speed-o-meter lol
Thanks for the vid!
I'm gonna try!!! Thank you so much!!! Hopefully it's gonna works out!!!🙏🙏🙏🙏👌👌👌👍👍👍
Hi im ebri I have An 08 MDX Acura and i experienced blinking D i unstood everything you said do untill you explained how to check the code by the blinking D. Could you help me?
what car is this for exactly/?? i have a acura tl 2005 with this problem, i thought it was the VSA switch.
Hi, my D light is blinking but they are all short blinks, no long blinks at all, what could it be? (No check engine light)
Awesome vid man!
Thanks for the video man appreciate it save me money!!!
Siomi i sure save about $400 doing it myself.
can this work.for.automatic car ?? for.the bypass?? i drive same car acurra tsx 04
Same thing on my 06 tl turned out to be the 3rd gear/clutch transmission fluid switch. The code was p0847 the part at my local acura dealer cost $80.
I’m looking to buying a 2004 tsx
Guy said the he has the same problem you’re having . But he bought the original part from Acura dealer . But his code is coming out P0958. He said it wa located in the center console . And it still came on. Any thoughts ?
Hello, my Acura MDX been doing the same thing and there's a message kept popping up in the dashboard "check transmission" it's also takes about 10 seconds to accelerate. Please help... Thanks!
Hey did you ever get that fixed and what was the problem
my 08 civic hybrid has the blinking D light. First the engine light came up then the speedometer stopped working before the D started blinking, When im driving and kinda press on gas then it kinda jerks instead of shifting...then I let go the gas and slowly step on gas until it gradually picks up speed and it will shift with no problem. One day while I was at the traffic stop the car started jerking and going from one gear to another, then I turned it off when I try to restart it, it won’t start again till date. I towed it to Honda and they keep charging me for more money testing but yet to find the problem: any one know what the problem is?
I have a Honda Accord CL7, 2003, with 137k, In my case it happens sometimes when im on Drive "D": After open the traffic lights suddenly i start to feel shift rought, jerks and when i change the gear to Manual (+/- mode) it's not respoding, even doesn't show me in wich gear/Shift im (if is 1,2,3,4,5) then it's starts to blink D and if i stop the car, turn it of and on again the problem it's gone. Any sugestion?
I have a 2011 honda accord thats been having this prob but im not very educated on fixing cars any help? Or are the parts that you said usable for my car??
Nvm on the parts
MUCH APPRECIATED...
great video bro.
Hi, yes. Well I got this problem.. well my transmission of an Acura Mdx 2005 started flashing the D5 at first and then after a couple of miles it starting to be harsh on getting to accelerate like if it didn't wanted to... so what can it be? Do I need to change it.
Ari Grande that’s similar to what I had except the car wouldn’t shift the gear up so I was stuck at like max 40kmh. The D green light kept on flashing. It’s probably either the input or output speed sensor. It should show you a check engine code so use a engine code reader!
Thank you it was big help.
I am really clad it HELPED! Make sure it click that like button and maybe subscribe!
Hi, I have the same problem with my Honda CRV 2009. I replaced the transmission pressure switch but the doesn't start. I have to codes on the scanner: $18DAF111 and $18DAF11D. please somebody help me
Thanks bro, i was scared too...Thanks
Glad it helped , make sure to like the video and maybe subscribe!!
Thanks for the video .. i got simple cuestion .. myb02 honda element automatic 4 cylinder start with check engine light but not d flashing liths my rpm max is 2700 or 2900 max my truck dosent run more than 65 milles if i phush the gas pedal starts to make like jumping and shakes.. do you think is the output and input sensors .. i can replace those same time just wan to fix my element please give me an idea please i replace the trid gear preshure swhich like 3 monts ago llease help...
Sounds like your car is in LIMP mode or something ...
Does a honda civic have a tran pump
I changed the transmission speed sensor in my 3.2 CL 2003 Base model because I was having this problem, although I was also getting a Torque Converter Clutch Malfunction code. Yet still, replacing this sensor and transmission fluid flush seemed to fix the issue, but not immediately. I still had some roughness for the first few drives, but then it went back to driving completely normal! About 7000 miles or so later however, the issue came back. I now come to realize after watching this video that only one of the speed sensor was changed. So I'm wondering if perhaps I just change both of then again (since I can't know for sure which one did or didn't get changed) if that would do the trick? Never done anything like this before but I've done a lot of research and so I think it's worth a shot. I may also change the transmission fluid with the good OE factory stuff, maybe also add some Lucas oil. I'm going to see if changing the grounding cables is needed also. These are all the things I've found. I may just try switching out the two sensors and reseting the codes if I csn figure out how (I don't have a computer check light reader) first. Will check back in case anyone is interested.
I'm thinking of purchasing the 2 sensors from amazon, my acura failed to change gears out of no where so I changed the oil (3 bottles) feels better but the problem comes and goes.
@@diegoqwe4864 check out inc3neration here on UA-cam. Really quality videos about this stuff. Mine was overfilled and so swapping fluid with 3 quarts of Honda now. Anyway, he had a video about changing the Transmission Oil 3rd Gear Pressure Clutch Switch. Very easy to change out, and could help a lot with this problem! I'll be changing mine even if my issues resolve after changing to correct fluid level.
Mtljack I have a 1999 honda accord ex. My engine light on and 4d is blinking. I put in a new pressure switch on the transmission code p1738. But I didn't salve the problem. Can you help?
Make sure you order a high quality sensor because some sensors don't have the exact resistance and the ECU doesn't like it. Ideally, get a oem sensor. Also, don't forget to reset the ECU by disconnecting the battery for more than 10mins or use a obd2 reader to reset.
hi I have an acura Mdx 2004 with d5 blinking and vtm4 light on a mechanic said a lot of problems coil pack,egr valve,misfires problem etc but I think he only wants stole my money what you think?
If its misfire ect, you should have a check engine light on, i dont think D5 bliking has anything to do with your misfires because the D5 represents the transmission itself , not the engine. Tell him to show you the codes so you can google the codes, this will allow you to find he true meaning.
I have a 2007 Honda Civic Hybrid. My problem is speedometer reads 0. Check engine light came on. D light blinks. Car drives fine minus when stopped. Will die if coming to a complete stop. Code read as vehicle speed sensor. Changed that out. No difference. Any thoughts?
vets fortrump
how did you fix this problem. can you please explain it to me i have the same problem with honda civic 2006.
my 08 civic hybrid has the blinking D light. First the engine light came up then the speedometer stopped working before the D started blinking, When im driving and kinda press on gas then it kinda jerks instead of shifting...then I let go the gas and slowly step on gas until it gradually picks up speed and it will shift with no problem. One day while I was at the traffic stop the car started jerking and going from one gear to another, then I turned it off when I try to restart it, it won’t start again till date. I towed it to Honda and they keep charging me for more money testing but yet to find the problem
Did you have to replace the input and output for it to work ? Or could I do the output alone I’m having the same exact problem for the Acura TL 2006 3.2L v6
The code will tell you which one to replace
May God bless you and your family bro .. Amin, amin amin.
Glad it helped!
I have an 07 acura but for me it only happens when I switch gears with the gear switch when I drive is nothing wrong can anyone help ?
I need help sir my car is a honda civic fd 2010 model automatic D drive are blinking? And after shifting D drive or R reverse are jerking?
Any check engine code?
DTC UO 121 F CAN MALFUNCTION (PCM-ABS MODULATOR CONTROL UNIT)
Check your brake pedal switch or sensor
Save my life dude 💯🐐
You very welcome ! Glad it helped! Make sure to like the video and maybe subscribe!
Thanks bro
The D light indicator went out and the car lost power for several miles before the light suddenly came back on and the issue cleared up entirely. 362,000+ miles now.
mine did the same was leavinmg for work one morning then my d4 started blinking and my engine light came on let it sit and came back the necxt day and it fixed im confusion but i aint complaing
I changed the spark plugs in May of this year but I put some German spark plugs, and the manual says that they have to be from the acura or Japanese brand, the mechanic says that they have to be Japanese, you think maybe you have to change the spark plugs again they still look good
Yes sir, never put german / american spark plugs in Honda / Acura , ONLY use NGK.
I got engine check sign at the board and the code read from Autophix OBDMATE 123 on my CRV 2002 is [ P1705 Short in Transmission Range Switch Circuit (More than one range position is on at the same time) ]. The D light is flashing sometime when I am on drive and once I switch ignition off and then on. It will stop flashing. It re-occur again mostly when I am on drive. What should I do for the case, bro? Any recommendation?
You probably have this problem buddy, ua-cam.com/video/BG-7fiLhK7A/v-deo.html , good luck
MTLJack Thanks for pointing out video
no problem , like and subscribe to help me out too , i could be of help in the future one day, thank you!
Learn To Share just get a (neutral safety switch )that's the range sensor,its only 2 bolts looking up
hey I have the same exact problem but I shorted something in the speedometer and I have the same code so I switched the neutral safety switch and same thing happened I need help any suggestions @@007rozier
i have a daihatsu yrv 2001
the blinking 4 gear light blinking i change the transmission and the tcm and the same thing
Maybe its the sensors. When you changed the transmission, you or the mechanic re-used the same sensors.
Any suggestions for a 2004 Acura rsx that “d” light continuously blinks with check engine light on all times and speed o meter goes up fast put stays roughly between 3 and 4?
But*
D light blinking points to transmission related problems. Sounds like you have similar problems buddy.
What was it
hey, what are the two parts again. whats number for the output and input??
You can buy them on rockauto, here's the exact link buddy
www.rockauto.com/?carcode=1422155&parttype=10634
Input shaft sensor : 28650PPW013
Output shaft sensor : 28820PWR013
MTLJack I’m having the same problem but my car is a acura mdx 2016, is this the same sensor that work for my car o should be another one? Thanks for any help
Is it dangerous to drive with it on
So “speed sensor “? Input & output ? I have a automatic Acura rsx hard shifting , can’t go into second gear , already did a trans fluid swap still doing the same hard shifting could this be the case ? Replacing the sensors would help ?
Is yours automatic or manual
Automatic
@@MTLJack hey bro im having the same issue with this tsx 2012 automatic that I literally Kurt purchased today 😩😩😩 please him me but I’m not getting any engine codes or check engine lights just the check transmission the car still acting normal no lack of speed or any of that can you please him me thank you in advance
Bro do u have a messenger needs to ask you some questions regarding my acura tsx thanks
Trippy G20 same here I just bought Acura tsx 2010 v6 and I'm getting a lot of these kinds of problems too. In my case no OBD2 errors.
Codes good for 04 to 08 TL? Reference for the codes? I have a 27 from the blink of the D light
Figure ot out ?
@@Rc-ho4sv my issue was a faulty 3rd/4th gear pressure switch. Easy fix.
@@meteoradar3252 so when it happened , did D blink maybe 4 times and then threw cel ? This just happened to me . im sure its something along the lines of the switches , solenoid or some sensor . im planning the 3x3 drop and fill after i replace all pressure switches and solenoid . other than the lights i have no symptoms except small fluid lose . Probably just a seeping line ....
@@meteoradar3252 did you check your code without a scanner ?
With my TL, the "D" was just flashing. I do not remember of my CEL illuminated.
To get the fault code for transmission, I followed a procedure that I found online that required me to short two pins together within the OBD port. The "D" in the PRNDL and the CEL would flash flash in a specific pattern that identified a certain fault condition.
In my case, it was the appropriate flashes for a failed 3rd/4th pressure switch
The process is online somewhere, do at your own risk, as you are shorting out pins on the OBD port.
Best use a scan tool that has the capability of pulling transmission codes. A common cheap scanner likely will not have the ability to read codes from the TCM.
The bad 3rd/4th pressure switch is common to fail and is very easy to swap through the left fender well. It's cheap and a easy attempt.
thanks bro
Did you hav Wyo replace the input and output for it to work
the code told me whichone to replace, i forgot which one i replaced lol
bro i have honda civic hybrid 2006. d indicator light is blinking and the car is jerking after a full stop at a stop sign.
i need your helpfull reply thanks.
my 08 civic hybrid has the blinking D light. First the engine light came up then the speedometer stopped working before the D started blinking, When im driving and kinda press on gas then it kinda jerks instead of shifting...then I let go the gas and slowly step on gas until it gradually picks up speed and it will shift with no problem. One day while I was at the traffic stop the car started jerking and going from one gear to another, then I turned it off when I try to restart it, it won’t start again till date. I towed it to Honda and they keep charging me for more money testing but yet to find the problem
I hope i get reply on this comment as I'm in desperate need of an expert opinion. My 2006 v6 Accord has the same problem, while i was driving on the highway suddenly the gear slipped back to 2nd gear the D light came up flashing plus the check engine light and VSA too!! Turned off the engine waited for 10 minutes the drove well for 2 minutes then the same issue happened again. After watching your video tried your method and got 2 codes, 70 and 76. Please help 😞
Did you ever found out what was wrong with your car
Hello,please I need help,my car is a Honda acura,1994 automatic and d4 are blinking.
You might have the same problem, use a OBD reader and read the code ! My reader told me it was the Output Shaft Sensor.
MTLJack thanx u. Shaft sensor(sped sensor.?)may be,becouse some time no work,and some time work .
Is it the same on 2017 Honda accord sport
I am not sure if the new generations Honda / Acura uses new codes but they could have retained the same meanings.
ya min is kicking but it was working fine before anything Ima check that out fuck bin almost a year and I found someone that knows what there talking about
If it kicks, it means your sensor is starting to have problems.
Do not rely on his OBD2 pin diagram shown at 5:36! Yes, do short pins 4 and 9, but the diagram shown in this video is backwards and will cause you unnecessary distress. Read the numbers on the OBD2 port itself--the four corner pins should each have a number printed next to them.
I have this same problem with my Acura TSX!!
Did you ever get it fixed?
The mechanic did use new sensor MTLJack
Dude this just happened to me on a roadtrip across the country to a new job. I have my son with me and we are stuck now and I'm running out of money for the motel. What do I do? I am having the SAME PROBLEM that you are describing
hey man, are the sensors both the same?
No, they are different sensors.
know anything about the acura tl v6 3.2? I have squeal while turning losing power when the transmission shifts down and having issues with transmission lag seems like 2 issues not sure though
Sounds like your transmission is slipping and starting to die. The Acura TL 3.2 , 1st gen & 2nd gen are known to have bad transmission =/
I have a 2003 honda accord and the D light keeps on flashing...HELP!!!
I have Acura tsx 2010 with the same problem, what's the solution?
Hey did you ever figure the problem out
It was the transmission input or output sensors if i recall, watch the video as i don't remember the details. I work on many many cars every week , sorry!
I have this d light flashing aswell but the car shifts fine no jerks no slips what could it be?
Flush transmission fluid
I could see where the sensor was located because it was too dark. Next time use a flask light to point out the sensor
I did this jumper method to get the trans code and blew my #4 ACG S fuse under the hood 15 amp. Car wouldn’t start or shift into gear until I replaced this fuse. Must’ve reset something because then my reverse worked for 5 minutes until the CEL and TCS light came back on. Anyways these pins to jump weren’t the right ones in my 2000 Acura TL!
Which jumper method? In this video, I only talked about what was my Acura TSX transmission problem, I did not show any fix methods!
And Acura TL 2000 does not have VSA, so wrong video my friend! You blew the ECU fuse.
MTLJack actually this is the right video because it worked on my car. You show it at 5:26 but your diagram is reversed! When I jumped 4 and 9 like you said I blew the fuse. When I figured out it was reversed and jumped the correct pins I got light flashes for codes on TCS, Brake, SRS and the D lights in the cluster. Thanks for showing this method of getting codes but I couldn’t find what they all meant online. I found my code reader later that day though.
MTLJack I used what would be pins 5 and 16 in the picture you are pointing to at 5:34 to get the flashing light codes.
@@TonioXenon I wish I would’ve read this about 10 minutes earlier than I did.😅
Do you short the ODB2 port pins while the engine is running? (5:26)
If you do, you will blow the ECU fuse. So don’t do that. Ask me how I know?😂
@@bdpgarage The problem is that the blinking "D" goes away when I turn the engine off. There's no code to be read. Did you follow the pin diagram he provided at 5:36? Is that how you blew the fuse? Or did you reference a correct diagram from elsewhere? (His diagram is shown backwards.)
@@niemand000theres another comment saying the diagram is backwards. Im off to find a repalcement fuse…
@@bdpgarage His diagram is a clusterfuck. Read the numbers on the OBD2 port itself--the four corner pins should each have a number printed next to them.
@@niemand000 tried pin 4 and 9 on the connector and it blows the fuse. Hard to see the small numbers but it looks right.
Thank You
Could a Check Engine Light (CEL) code:
P0756 Shift Solenoid B Performance or stuck off
for a '04 Honda Accord EX 2.4L 4-Dr Sedan Automatic (approximately 259,000 miles) just be a Solenoid issue or something else (Pressure switch, etc)
if the car is not going into Reverse for up to 2 minutes & the same thing for Drive (Have to wait a few seconds up to 2 minutes) Drive light blinks, Check Engine Light is on & that is the only code displayed;
P0756 Shift Solenoid B performance or Stuck Off
(Other issues: Sometimes there's a quick grinding sound when the car is switching into gear usually after the car is stopped at a stop sign/light then moving again, RPMs rev up high but the speedometer stays low & takes a while to switch gears. After the CEL had been cleared the car drove fine in all gears, 65mph no problem, etc then when the CEL & blinking Drive light came back on it had the issues listed above).
Other Notes: Honda dealership recently drained/filled with new transmission fluid approximately 3 weeks later while up in the mountains I had a loose negative battery connection; dashboard lights flickered, RPMs reved high with harder shifting, after I realized it was a loose negative battery connection I used a SHIM to fill the gap>Battery connection issue fixed but then I started experiencing transmission issues; Just delayed shifting (High RPMs before kicking into gear) took the shim off which obviously involved disconnecting the negative battery cable then lone behold the car was shifting fine. Had to put the shim back in (loose connection) then the same transmission problems started to occur again & became progressively worse as mentioned above. Later after the car finally kicked into Drive it was taken to a transmission shop & they said they were barely able to get it into their bay by pushing it (While in Neutrel) They said it needed to be driveable to run their scan tool to pull codes/test the transmission & their final result is they said it needs a rebuilt transmission ($4500+) no code scans, test drive, they believe it couldn't just be the solenoid, etc. Since it delays so long and or doesn't go into Reverse gear or drive (Not sure how long they actually waited to give the car a chance to go into those gears). If the transmission is actually no good I will take it to a shop that takes the exsisting original transmission out & rebuilds that $2000-$2800 instead of this shop who only orders comptely rebuilt ones for $4500+ (They said they don't rebuild transmissions on foreign cars because they had too many issues & only rebuild original transmissions on American vehicles). Just wanted some feedback, opinions if they still could've scanned the vehicle properly since it starts & even if it can't kick into gear to test drive it and also based on this info if it still could be a Solenoid fix etc (Lengthy info in case this is helpful to determine the issue better & in case this is beneficial to anyone else experiencing similar issues).
I'd go to the Honda dealership where they have factory trained Technicians that know the product
i have the same situation im hoping its electrical
battery ground resolve ..
I have a blinking D light but not a check engine light... (2002 Honda civic EU 5 doors hatch)
Does your check engine light work?
@@MTLJack yes it does work
I got 73 for my civic 2006 but not in the list😭😭
sorry i coulnt help !
My engine is a vtec 6cil 3.0.
Bro thank you ! This just happen to me a few days ago I have a 2005 Acura TSX when u was on the highway the flashing d blinking so as my engine light I had bout a 1hr drive home n made it the same day my gears was stuck! N I couldn’t move only a few feet then the speed sensor would say 0mph then go slowly to 20n get stuck I was n a panic I check my trans fluid n it was empty put some in n the car got to jerking randomly so I flush the fluid it was black completely put new fluid in n it sorta runs ok but I can feel my speed odometer doesn’t keep up it reacts late from when I’m pressing the Petal n I’m thinking I need what u needed I’m praying that’s it fix the problem
Joseph Malone if you have a check engine reader, try to pull out the codes! I had same problem as you except my transmission fluid was full
Yea mines was full they told me that’s why it’s was doin that so I took out a lot I had it full way pass the two bots but I’ll try a reader tomorrow hopefully that’s what is Man because I really love this car n hate to junk it
Joseph Malone if it’s the sensors then it’s easy fix :) I ordered the parts from Rockauto ,good luck buddy!
I have a 2005 Acura TSX Auto with a code P0756 Shift Solenoid B Performance/Stuck Off, and with a flashing “D”. My car won’t move at all when it’s in “Drive” or “Reverse”. Is this really a Solenoid problem? Cause I was told that that code is a transmission problem with the filter inside of the transmission. I was told that I would have to get my transmission dropped and disassembled to get to the filter inside of the transmission 😪
Unfortunately, I don’t know much about the solenoid. My problem was much simpler :(
Having the same exact issue: '04 Honda Accord EX 4cyl 2.4L Did you end up finding a fix for the problem?
MileHigh Built Yeah I got my car back running. It’s the transmission. I guess the filter that’s inside of the transmission they get clogged up if you don’t do a transmission flushed right away the transmission could get damage do to the fluid not flowing fluid and cause the clutches to get burnt. In order to get to the filter you have to disassembled the transmission. I paid 1,700.00 to get my transmission rebuild including the rebuild kit and torque converter. My car runs a lot better.
Honda city 2018 d light blink
P0752 shift solenoid A on !! This my problem I don’t know 🤷♂️ please what school I do
did you ever fix it ?
My Acura TSX 2004, won't go over ten miles an hour. It won't shift it just revs. Now, it won't reverse.
You probably have same problem as i did The computer cant figure out what gear it is in therefore, you are in limp mode. Sounds like either a speed sensor or the sensors i mentionned. Easy fixes but make sure to buy HIGH QUALITY sensors. Don't cheap out.
@@MTLJack Will do, Thanks pal!
My D, L and engine light came on too..
It indicates you have a transmission problem unfortunately :(
My car stopped letting me shift at all and when I put in drive or reverse it just revs the rpms but doesn't move. I can move the shifter to different positions (park, drive, reverse, etc) but nothing happens, it wont even go into neutral
Broken axel?
Hi I'm having the same problem the D keeps blinking and I took it to autozone and they told me the code which was p0700 so u think this would work ?
angel hernandez if it shows P0700 then its P0700, i had another code so it wont work
can you tell me what did you do to fix it ? ihave the same blinking D with p0700 code
Green Transmissions HONDA and ACURA TRANSMISSIONS
SIMPLY DEMONSTRATE WHILE INSIDE CAR
I cannot believe how many fucking problems my 2005 Tl has. It’s like a new thing every month. Last month it was engine misfire. Now it’s this shit. What the fuck
What a about a Acura rsx
I got p0979
Honda Civic 2000 lx D4 Problem everything works but it won't run on d4 while it runs on 1,2 and D3. Anyone encounter a similar problem? Appreciate if you leave a comment on how to improve my car.
I don't know well enough about Civic 6th Gen sorry, sounds like a transmission sensor problem similar to mine. There should be a check engine light if its transmission sensor problem, otherwise,you have a mechanical problem.
MTLJack So if the check engine light is on it means it's a transmission sensor problem?
Not necessary , maybe you already had a check engine before. Use a OBD2 Reader to read the codes. Good luck
Johan did you find the problem?
BRO I CROSSED THOSE TWO PINS AND IT NOW MY CAR WONT READ MY KEY..... WHAT THE FUCK.. NOW IM REALLY FUCKED
No t keremos ver a ti..si no el problema
I tried it, I got a 27
What car is it? sounds like a awd acura / honda
Rockaudo
Hi tocking a lot and I don't understand noting!!?
What the F are you saying?
Honda is the worst car. don't buy it.
im gonna unsuscribe this guy dont respond
Trippy G20 I was going to reply until you wrote this. Good luck.
MTLJack Yea years later w.e. dude
Trippy G20 There's a thing called vacation, sir.
MTLJack Awnser my question dude
write me privately , mtl.jackk@gmail.com
ATOMIC TRANSMISSION FLUID TEMPERATURE SENSOR!!