I have this installed in a SonicModell AR Wing. Everything works well except for one very annoying bug. The OSD drops out intermittently several times during the flight. The video is solid, but the OSD drops out. I have triple checked everything and even replaced the flight controller but the problem persists. I am not using the 5 volts from the ESC but am powering the board through the battery voltage only. I'm ready to pull out the F405 and go back to an OmnibusF4.
Great video. Very helpful But I am facing some issues, Every time I try to update using windows 10 pc or flash arduplane firmware on this board, INAV fails and show the log "failed to open serial port" I have tried impulse RC driver fixer and zadig, still I unable to flash the arduplane firmware. Please suggest what could be done to solve this issue.
Ben,in the modes tab in inav all my flight modes that im programming go blue via the 6 position switch im using except the nav rth the small blue line is within the window ive allocated but dosnt go blue to say its ok.......any ideas please or anyone?
Hi! Thanks a lot for that video!! It help me so much!!! Only think I do not understand is how to setup failsafe I have L9R .I have set in my Taranis "hold" and don't know if i should press also the button on the RX or it will work with no press the button..?? Thanks a lot for any advice from anybody .Bob
Proberly the most informative video ive seem Ben,im putting same unit into a fixed wing ranger 2.4,i take it you have only set up this wing with maytec 405?..
Thanks for great video, im building my first flying wing and using f405 wing flashed with inav 2.5 my reciever is r xsr that binds to my radiomaster tx 16s. Problem is i have no stick inputs in inav maybe you can help? Thanks
Now you are using 2.0 I think, I use 1.9 that is bullet proof, and use the older configurator, plus you may need this settings. for auto launch nav_fw_launch_velocity = 300 nav_fw_launch_accel = 1400 nav_fw_launch_max_angle = 45 nav_fw_launch_detect_time = 40 nav_fw_launch_thr = 1800 nav_fw_launch_idle_thr = 1000 nav_fw_launch_motor_delay = 500 nav_fw_launch_spinup_time = 100 nav_fw_launch_timeout = 10000 nav_fw_launch_climb_angle = 20 set max_angle_inclination_rll = 600 set max_angle_inclination_pit = 600 set small_angle = 180 set nav_fw_bank_angle = 35 set nav_rth_altitude = 3500 set failsafe_throttle_low_delay = 0 set nav_rth_allow_landing = NEVER set disarm_kill_switch=OFF
because the compass will go in the direction home is no exactly the lat or log, just the direction so if you launched and flight south if you have a fail safe he will turn back to north but maybe 2 miles away from you because the wind make him drift , with gps lock failsafe the plane will go to lat and log regardless of drifting, and will come back Home, only quads need magnetometer to return home because they flight what is call in 3D space. Magnetometer and GPS are not good for eachother, also removed the nav hold on you modes., if you decided to removed magnetometer.
Awesome! Thank you! I noticed it was doing some freaky things with the home location last time I flew it. I'll try again with it disabled. Many thanks!
Happy flying.
I can see many people look for basic help with this maytec control,please post more on this topic your very wasy to understand and you p resent well.
fANTASTIC KEEP POSTING YOU PROGRESS.
Valeu 👍 já inscrito
I have this installed in a SonicModell AR Wing. Everything works well except for one very annoying bug. The OSD drops out intermittently several times during the flight. The video is solid, but the OSD drops out. I have triple checked everything and even replaced the flight controller but the problem persists.
I am not using the 5 volts from the ESC but am powering the board through the battery voltage only. I'm ready to pull out the F405 and go back to an OmnibusF4.
Great video. Very helpful
But I am facing some issues, Every time I try to update using windows 10 pc or flash arduplane firmware on this board, INAV fails and show the log "failed to open serial port"
I have tried impulse RC driver fixer and zadig, still I unable to flash the arduplane firmware.
Please suggest what could be done to solve this issue.
Ben,in the modes tab in inav all my flight modes that im programming go blue via the 6 position switch im using except the nav rth the small blue line is within the window ive allocated but dosnt go blue to say its ok.......any ideas please or anyone?
Its all good now problem was new version of inav i downloaded.....dont know why but works fine now.
Hi! Thanks a lot for that video!! It help me so much!!! Only think I do not understand is how to setup failsafe I have L9R .I have set in my Taranis "hold" and don't know if i should press also the button on the RX or it will work with no press the button..?? Thanks a lot for any advice from anybody .Bob
Proberly the most informative video ive seem Ben,im putting same unit into a fixed wing ranger 2.4,i take it you have only set up this wing with maytec 405?..
Yup! Inav a tricky thing
Thanks for great video, im building my first flying wing and using f405 wing flashed with inav 2.5 my reciever is r xsr that binds to my radiomaster tx 16s. Problem is i have no stick inputs in inav maybe you can help? Thanks
There’s any manual of this FC?
Do you know if this flight controller will work with Spektrum receivers?? If so which port do I need to turn on? Thanks for any help.
That's a great question, not sure but I'll see if I can find any info
mindofBen thank you so much!! I’ve really struggled to get this board to work but your video has helped a ton!!
Do I need to set up in my radio a plane or swing?
Depends on the aircraft but in this example, I used a wing on the radio 😊
Now you are using 2.0 I think, I use 1.9 that is bullet proof, and use the older configurator, plus you may need this settings. for auto launch
nav_fw_launch_velocity = 300
nav_fw_launch_accel = 1400
nav_fw_launch_max_angle = 45
nav_fw_launch_detect_time = 40
nav_fw_launch_thr = 1800
nav_fw_launch_idle_thr = 1000
nav_fw_launch_motor_delay = 500
nav_fw_launch_spinup_time = 100
nav_fw_launch_timeout = 10000
nav_fw_launch_climb_angle = 20
set max_angle_inclination_rll = 600
set max_angle_inclination_pit = 600
set small_angle = 180
set nav_fw_bank_angle = 35
set nav_rth_altitude = 3500
set failsafe_throttle_low_delay = 0
set nav_rth_allow_landing = NEVER
set disarm_kill_switch=OFF
My Motor Not Working
Does it beep and twitch when you power on?
yes my buzzer beep@@thegreatflyingbenjamin
Remove you magnetometer is not good for fix wing.
I've heard that too. Why is it not good for a fix wing?
because the compass will go in the direction home is no exactly the lat or log, just the direction so if you launched and flight south if you have a fail safe he will turn back to north but maybe 2 miles away from you because the wind make him drift , with gps lock failsafe the plane will go to lat and log regardless of drifting, and will come back Home, only quads need magnetometer to return home because they flight what is call in 3D space. Magnetometer and GPS are not good for eachother, also removed the nav hold on you modes., if you decided to removed magnetometer.
Awesome! Thank you! I noticed it was doing some freaky things with the home location last time I flew it. I'll try again with it disabled. Many thanks!