I was excited to check out those ostrich feathers you suggested too, looked handy & I couldn't find them anywhere. Maybe you can provide that info next time. My kid would love using it when working with me.
I'd like to point out that you have been lead up the garden path with the battery buzzwords. There is no viable "solid-state" battery on the market in any commercial form yet, and not likely to be for many years, the best we have at the moment is LiFePO4. As for being "the only one" when it comes to solid state electronics, this is also demonstrably false. We have been making and using solid state inverters for 30+ years, it doesn't make sense to manufacture them any other way, it's the cheapest and most efficient method of inverting power. A good example is your cheap after market car amplifiers, they have inbuilt inverters to step the voltage up from 12V to 60+V as this is what is required to obtain 60W+ RMS of audio. Before continuing to use the term "solid-state" please do some research on what it actually means. Based on the advertising material you show there, it's a 1.1kW battery, in this package size there is zero doubt this is a LiFePO4 battery.
Interesting to see how the internet has taken the craft of woodworking and turned it into marketing. Just like the guys selling shovels during the gold rush. What a trip
That was the case long before the internet. Go watch a "This old House" and notice the product positioning. The woodshop guy hawked products as well. It's also prevalent in the DIY auto garage genre of shows.
THANK YOU! Noise cancelation is not hearing protection! My earbuds were $6,000,. . . ok, they are hearing aids, but the Bluetooth music through them is amazing because they are totally tuned to my hearing loss. That said, I often have to take them out when doing loud work to put in plugs, though sometimes, I'll shut them off and just put the muffs over them, that is, until I go to the range, where I use plugs and muffs. Very informative video. While I've done little projects for years, I recently put a lot of my skills together while building out new shelving in the back of my new work van and number one tool I wish I had was a track saw, but lived with a set of straight edges, clamps and the tape measure. You earned my subscription with this video.
Tool #11 that you need is a dustmask. Your dust extractor will still blow very fine dust back into your garage and not all dust is captured at the tool (even with Festool). I have a versaflo mask from my dayjob that I use at home while carpenting. Bit overkill maybe but it has a fan with filter, an option for earcaps with bluetooth (radio/phone), protects your eyes and if you get the welding face shield with it then your can use it for that too.
Ho-lay! There may be other models, but the first “versaflo mask” I priced was US$1800! I’ll bet it’s good at that price! I’ll bet thereother good powered masks, maybe one that’s “good enough” for casual use, but less than the tablesaw I want to buy, used!
I'm in the same boat for being in a 1 car apartment garage, 1 outlet no breaker and never would've considered a PowerStation for running things like a planer or bigger tools. Definitely gonna be picking one of those up ASAP. Also gotta say, the dust collector in the rafters is genius!
I wonder if it would be possible to put an in-line breaker between the outlet and the main panel, that way the maintenance wouldn't have to come for evry tripped breaker.
Even if you already own a drill press the drill guides come in very handy for when you can't use a drill press. Like you said for the price its a no brainer!
Pica is great, BUT I'd recommend getting the HB graphite fillings immediately the B2 (or whatever comes standard) is very soft and you'll be sharpening after every single mark if you want a fine line.
I have been using 1.1mm mechanical pencils for years. This was a result of the 1.1mm mechanical pencils we used in the Air Force. My favorite has been a double ended twist pencils with regular, red, green, or blue.
I sand a lot of smaller pieces (from 2" to 12") and I use a machine anti vibration mat, I used one under a mini CNC and realized the surface is very high friction and I can throw a 5" round board on it and sand without ever touching it, now some longer narrow pieces do move a little (never more than an inch or so) so I do keep a finger on them but this mat is amazing and changed my sanding forever. I had tried the same mat in your video and yea, it just slid around but the machine anti vibration mat does not.
Great video. I just subscribed to your channel. I really admire guys such as yourself who are able to work with what they have- a small shop- and put out great work. I do believe this helps make people better woodworkers. Thank you for tips and suggestions. I also like that you are not bombastic in your presentation. Good work.
Ostrich feathers, great video. As a retiree woodworking and knife making which I do go hand and hand. Your ideas are point on keep up the good work man.
I emphatically agree regarding the woodpecker track saw Square! I have had mine for about three years, and I have never used it for anything other than 90° cuts. Unfortunately, TSO‘s Square was new at the time if it was available at all. If I could do it over, I definitely would’ve went that route. Having said that, I will be getting their parallel guides.
Lovely tools... One small tip, if your limited in power and have to wait before the fuse is replaced you can also put a breaker circuit in your shop, preferably just a bit lighter so that one breaks before the inaccessible one does. I did that in my shed because I found walking from the end of the garden to the actual breaker box costs me too much time, yeah I'm lazy ;) Of course the power bank is still super handy there, but I'm not sure if it will power all of my stuff like compressor, welding machine. But thanks for the idea, combining it with the actual net power will help in certain situations.
for the router bits, when looking for them online they are called compression bits. you can also get end mills like that. keep in mind those are amazing for laminates, plywoods, and yeah. hardwood (although straight honestly works... just fine for hardwood). in the video i saw you use the compression bit on mdf.. that in my experience decreases the lifespan by ALOT. those tools are usually sharpenable 2-3 times but the mdf really tears it a new one and you will not get the best return on your investment. keep an old one for mdf, it doesnt require sharpness really anyways, just the shearing angle to get the surface nice and clean.
my sister got me some earbuds last year that are pretty great, they block out just about all sounds and i can use them while running my chain saw without any pain in my relatively sensitive ears, they have great sound quality and you control your music/book by tapping them
Thanks for the new track saw square idea- for $189 bucks. I built my own from scrap basically for free and it works great! Merry Christmas and thank you for the video.
Lol. Funny comment, but just because he may not have bought ALL those things does not make the info and recommendations any less valid. What would help would be a video on what is not so helpful. The only tool I regret buying in 40 or so years is a Port-a-line. It’s drill attachment to make perpendicular holes. I used it one or two times since I’ve had it. I have a drill press I bought used and I’ve used it many times since then. I will never be without one again. Having said that it’s not real convenient for edge drilling or large heavy pieces of wood or steel.
14:00 Those mats work perfectly. Your problem is that you have both, a very smooth table top, which most do not. Also you have a rather dirty table top, at least you did when you "tested" the mat. If you did not have either of these issues you would have a much better experience. Basically the dust is acting like a lubricant, yes, dust is a lubricant. Just check out the graphite dust in your torch converter. Anyway, to easily solve this problem you can just wipe your table top with a slightly damp cloth. Then wipe the side of the mat that with be facing down with the slightly damp cloth. This should remove the majority of the dust and prevent it sliding around on you. "Well its a wood working shop, its going to be dusty". Yea, good point, but it almost seems like you set that up on purpose to make the mat look like it doesn't work just to promote that other product. Not saying thats what you did, but intentional or not you created the one situation where that mat would not work well which is also very easy to solve in less than 20 seconds.
Getting a large pencil lead holder is quite helpful. Can't speak for the one demonstrated in video, but getting a 2mm lead holder in general is great. Durable tip when marking, lots of different colors available, and the lead holders are inexpensive enough to have a few for quick access to different colors.
I have a 3mm mechanical pencil I got from Temu. I haven’t had a need to use it yet, but I’m sure it’s much better than the ever breaking thin crap we’ve all used. I’ve used carpenters pencils for decades. I can sharpen them to a needle point with a utility knife.
There's a similar one from a brand called Tracer, they call it a "Deep hole construction pencil" £15 gets you the pencil, holster (Has a sharpener built into the pocket clip instead of awkwardly stuck on the end) and a lead holder with 6 spare leads, add another £2 and you can upgrade to a triple pack that adds a permanent marker in the same deep hole style (For any Brits reading, Screwfix or Toolstation usually have them in stock) No idea what the availability or price of these are in the US or elsewhere, but I learned of it from a US creator so I'd imagine they're available, I'll never use a normal pencil in the workshop again, in fact it tends to get used for any pencil task whether it's in the workshop or otherwise lol
I have a set of 3M Worktunes bluetooth hearing protection. They work exceptionally well with awesome range. I've taken phone calls while sitting on my Kubota garden tractor while it's running and they can hear me okay. There are times I would rather have something smaller to use like when I'm in the workshop. Thanks for suggesting the Elgin products. I'll look into them.
I also use the worktunes, and love the sound they produce. I prefer them over those things you stick in your ears (comfort), not to mention losing one of those small expensive pieces won't happen with the headset.
Elgin Ruckus are great, they actually stay in my ears unlike nearly every other in-ear headphone I've tried. I'd also say look at the Bora Centipede if you need to modify your work space a lot. Being able to set up a large work table for some jobs then teardown in a minute to make room for other stuff is great. Their workbench table pieces are expensive, but you can make your own.
I’ll check Bora out, thks. For plain earbuds, not hearing pro, I like QCY a lot: reasonable sound quality, very lightweight, cheap - TC-13ANC ~US$25.00, and they stay in my ears, unlike ibuds. Also, hate to say it, but Bose earbuds stay in well. Not ear-pro either though. Also not cheap. If I were to spen the $ for sound quality in earbuds, it would be for Sony. Also not ear-pro!
Checked Bora out - looks like some folks like their customer service…also looks like they have and need lots of practice. Take their straight edge clamp. Too many issues!
As a biker who loves to travel a lot, the Rebel ear protection looks great. I will look into them for my big 2024 ride. Grip it like nobody is watching.
Thanks Eric for this list. I own many of these items, but now have a few more for my wish list - just in time for Christmas. Bonus, most are low priced & almost all will fit in my stocking (getting the hint santa?). Seriously, thanks for putting this list together. I always learn something from your videos. Today’s practical tip was leaving a ~1/16” gap between tracks when connecting them. I haven’t needed to connect my tracks yet, but now I know what to do. A smart person learns from their mistakes. A wise person learns from the mistakes - of others….
I've always found ostrich feathers are great for sweeping up saw dust from behind my machinery. The Pica marker is definitely the best marker I've used.
Ostridge Feathers are a poor substitute for down in my winter underwear! I wish I had seen this video before I installed a new subpanel to supply power to all my tools even though I only use them one at a time. I am grateful for your sharing knowledge and the method you have to do so.
This is a great video! I hadn’t heard of the track square thing before but I need one. I enjoyed the “grow up”. I enjoyed the frequent enthusiastic waving at the camera. Just generally helpful good vibes 😎 I’ve subscribed 👍
I bought 30 pounds of them and attached them to my table saw, thinking it would allow the saw to fly around the shop to wherever I needed it. Sadly, the saw remained flightless. Who knew, right?
I have Pica pencils and the pens are awesome - I use them for absolutely everything! Even writing my son's name on his school clothes! I also have a drill block/guide and for what I do it takes up a lot less space than a drill press and even fits in the drills carry case easily too!
sometimes i think that ostrich feathers are the best for causing mass chaos when thrown from tall buildings. even more so if still attached to the bird! great list!
At Woodcraft in Seattle, we (don't) hide our ostrich feathers in the drop-ceiling so when we need them we might forget where they aren't . . . I'm subscribed!!!
Ostrich feathers are great... But I struggle with catching the little buggers! OK... The pencil... Everything you recommended was cool, but I NEED that pencil NOW! LOL! Thanks for sharing!
Ostrich feathers and the Kreg Drill guide always come in handy. Used the kreg tool to drill some tricky stainless steel tubing, was a little concerned at first, the drill guide made it a snap. (And 3in1 oil for the bit.)
I worked out of an apartment house garage for a little while. I worked for a cheapskate boss. He wasn't there to put up with the irate tenants yelling at me, who were paying good money for their substandard apartments. Do everyone, including yourself, a favor and either buy a suitable place or rent space in an area suitable for commercial use. Just holding off on a couple of Woodpecker tools will pay a month's rent. You can even rent a corner of someone else's shop for very little money, just make sure you can lock your stuff up. You are doing good and will be doing a lot better when you get out of that garage.
I feel you. The people who upgraded my 1880 house, and built the garage certainty were not craftsman. The whole garage is on one 15 amp circuit. That includes the decorative lights that are built into the brick wall that serves as a fence. I can't run the window A/C and the air compressor at the same time. I barely get away with running the A/C and my 6" Atlas lathe at the same time. Every time that I forget I have to walk to the house, go to the basement, and reset the breaker. I'm honestly looking in to setting the garage up with a solar charged battery bank.
23:02 If I have something too big to put on the drill press, I sometimes use double-sided tape to attach a circular bubble level to the back of my electric drill. Another way is to get section of 8/4 board and cut a V in the end of it and put your bit in the V to keep it vertical. With drill guides you're limited to the sizes in the guide. The V-block will accommodate every odd size. Use a 4/4 board for smaller bit sizes.
@@Thornik2012 uxzyRtHXN5Y - Kind of like this guy did but he made it harder than need be. eSJtG947ZPk - This is similar to what I do. I find it easier to put a notch in a piece of wood with a band saw.
The most important item mentioned is by far any of the hearing protection. Just ask anyone with tinnitus and or hearing loss. Hearing loss is great when your going to bed, but not so much when trying to have a conversation with someone or watch TV.
🎶 click click punk now you’re thinking oh sh!t, quit while you’re ahead before I fill you full of lead🎵 That’s the house of pain/cypress hill jam. Great video dude!
Normal mechanical pencils come in thicker lead than 0.5mm which I used for years and they break all the time. I now use a 0.9mm for woodwork as well as sketching and general writing. I buy the Pentel Twist-Erase, great eraser too. They basically never break. Plenty sharp for general writing. Although the white lead pencil that writes on anything looks fantastic.
+1 for the corded hearing protection + Earbuds. The FIRST time I used some without the cords that hang around my neck, one fell out of my ear, and ended up going through the blades of my table saw....RIP.
If you have problem with breaker tripping in technical room you dont have access to, just make your own IP96 breaker box that get power from the one outlet, and you can then put multiple outlets after that breaker. If it trips, it should only trip that one, while allowing all your tools being connected, just dont go over the limit. Usually machines take most power when starting so you might consider making capacitor bank to give that little extra boost of power when starting, though talk to your local electrician about this and those big caps can cost a lot. Alternatively ask your building management if they could pull another wire and breaker from the technical room for your garage, specially if you are willing to pay the bill for it, or your landlord is.
Try Bose noise cancelling over-the-ear headphones. I did about 2 hours of sanding last night and literally had to lift it off my ears to see if the shopvac was really on while jamming to my fav tunes. Agreed on the boring factor without music!
you should definitely do a video on how you manage your electricity and outlets... I also work in a one car garage with one outlet and would be curious how you get things done
Hello, I enjoy your videos they are very informative for me since I am building a shop in my garage. I bought a workbench with dog holes in it but my bench dogs do not fit in the holes. The bench dog shafts are 19 mm, is the UJK reamer/chamfer tool to large for my bench dogs? Thanks, Tom
Enjoyed the video. Only thing I disagree with is the no drill press. Bench tops are inexpensive, they don't take up much room and a god sent when you need one.
Thank for sharing. But I really wish woodworkers can keep coming up new ways /setups to use their fancy tools. Is it really that hard to design a table setup to use track saw for repeatable cuts instead of keep buying these not so cheap but really limited tools?
I think all the ostrich feather comments are hilarious. Thanks for putting this list together. I've ordered several of the items already! Happy Holidays to everyone!
A lot of those Festool tools, look like you're buying tools, just to buy more tools. This is akin to creating more work for yourself ( something that I generally try to avoid ). In most engineering circles, the DRY principal is quite effective, and repeatable template patterns provide the most efficiency when used in larger quantities. I'm pretty sure that you could address many of the problems illustrated, with less cost, less effort, and higher ROI.
Hey Sir, I think you are my favorite subscriber on UA-cam. I found you while up at 2 am feeding my kiddo. You have a way of connecting with the camera. Your information seems very helpful, trustworthy, and genuine. Keep making videos. I have been wanting to pick up woodworking for a good three years as a hobby. I keep making excuses on not starting. I think as a result of this video I may finally start. Thank you!
Ostrich feathers!!! The Pica pencils sound like a new take on the draftsman mechanical pencils of the 70’s. We had a desk spinner with a sandpaper cone inside to keep them sharp. Definitely recommend HB or 2B hardness to keep the point longer.
When it comes to the Flush Trim router bit, I actually would recommend the newer models that also utilize the carbide inserts similar to the helical cutter head used in planers
Just found your channel. Not a wood worker, just an enthusiast. Bought the pica pencil through your link and will likely get a couple other things. Also did the ostrich feathers. Great video. I subbed. Merry Christmas.
Ostrich feathers, come in handy for many things…. They make pencil sharpeners for carpenter pencils, so they’re not really that difficult to sharpen but nice sales pitch for the pencil. Also, Raycon makes really good earbuds and their far less expensive than many others.
Eric, I just came across some of your older vids (I bet you can guess which ones) and that led me to the actual woodworking ones. I love them. I've subscribed and I'm looking forward to exploring your back catalogue along with your new stuff.
Having used several different BlueTooth "ear protective" earpods or headphones I found that they all have limited max volume levels on the volume controls. This is done to protect your hearing which I guess is good but means that you won't be able to hear your music or whatever while you are actually using your noisey tools.
I used to have one of those pens. But then my father came and helped me on a project the day before fathers day. He constantly misplaced his regular carpenters pen. So, I gave him my pen as a fathers day gift and I need to get a new one. Much more convenient than tying ostriche feathers to the pen to find it!
Hi there, I'm a first timer to your channel and I really enjoyed this video. Can you please share the type and/or brand name of your central metal work table?
The compression bit is a great tip. I make cabinets and we often have to cut a panel or counter top with a router in the field and it would be nice to not worry about laminated edges
That's so generous of you to make an actually decent useful list even for beginners like me. I wish I could afford those Elgin, my tinnitus and my tools don't get along well... Only complaint is that they don't show their sound curve, so we can't even tell how good/bad they would be for our music. I'm sure they're awesome for protecting our ears, but as they are technically marketed as true wireless earbuds, they should at least be transparent and show their sound profile somewhere.
tbh im using an old yoga mat as non slip thingy for sanding. works great as long as you put it on a clean table. if there's already a bunch of dust, the mat will happily slide on the layer of dust :D
Which tools highlighted in this video, (if any) are you not sponsored by or get a kick back from? For me, I find that recommendations that have no monetary influence behind then carry more weight.
Exactly. I stopped watching when there was no mention in the video description or beginning of the video of whether or not any of this is affiliated/sponsored content. As a result, even watching this is a hard pass.
As an alternative to the Kreg Drill guide, I have and really like, the Big Gator Tools drill guides. They are a little more money, have a lot more drill bit sizes per guide, and are made in the USA. Oh, and Go Bucks!
●TSO Track Saw Square - tsoproducts.com/guide-rail-squares/grs-16-pe-parallel-edge-guide-rail-square/?ref=sdc
●Woodpeckers Track Saw Square - amzn.to/3G6efhp
●Yoshino Battery - amzn.to/49MFSJE
●TSO Track Connectors - tsoproducts.com/jigs-fixtures-guides/grc-12-self-aligning-guide-rail-connectors/?ref=sdc
●Festool Track Connectors - amzn.to/3MQh0ah
●TSO Parallel Guides - tsoproducts.com/parallel-guide-system/tpg-parallel-guide-system/?ref=sdc
●Elgin Rebel (10% off Code “SDC10”) - bit.ly/3CsTBXf
●Elgin Rebel Replacements (10% off Code “SDC10”) bit.ly/47oiRey
●Elgin Rumble (10% off Code “SDC10”) - bit.ly/3XaaAW7
●Elgin Ruckus (10% off Code “SDC10”) - bit.ly/47IlA26
●Elgin Discord (10% off Code “SDC10”) - bit.ly/3CpzqJx
●Elgin Rampage (10% off Code “SDC10”) - bit.ly/3Iwp6n4
●All Elgin Products (10% off Code “SDC10”) - rebrand.ly/o8v4x9k
●UJK Chamfer & Reamer - tsoproducts.com/bench-dogs/accessories/ujk-combined-chamfer-reamer-tool/?ref=sdc
●UJK Chamfer Only - tsoproducts.com/bench-dogs/accessories/ujk-chamfer-tool/?ref=sdc
●UJK Reamer Only - tsoproducts.com/bench-dogs/accessories/ujk-parf-system-reamer-for-20mm-holes/?ref=sdc
●UJK Anti Slip Pads - tsoproducts.com/bench-dogs/ujk-parf-dogs/ujk-anti-slip-workbench-protection-dogs/?ref=sdc
●UJK Adjustable Anti Slip Pads - tsoproducts.com/bench-dogs/ujk-parf-dogs/ujk-adjustable-work-support-dogs-four-pack/?ref=sdc
●UJK Ultime Dog Hole Kit - tsoproducts.com/bench-dogs/ujk-parf-dogs/ujk-super-dog-accessory-kit-in-t-loc-systainer-case/?ref=sdc
●Giant Top & Bottom Bearing Compression Bit (10% off Code "SDC") - bitsbits.com/product/udc9112-ultimate/
●Giant Bottom Bearing Compression Bit (10% off Code "SDC") - bitsbits.com/product/udp9112-pattern/ref/6234/
●Top Bearing Compression Bit (10% off Code "SDC") - bitsbits.com/product/udft5152-flush-trim/
●Top Bearing Downcut Bit (10% off Code "SDC") - bitsbits.com/product/rftd5200-down-cut-flush/ref/6234/
●Top Bearing Upcut Bit (10% off Code "SDC") - bitsbits.com/product/rft5200-flush-trim/ref/6234/
●Skinny Top Bearing Compression Bit (10% off Code "SDC") - bitsbits.com/product/cm250ft-flush-trim/ref/6234/
●Skinny Top Bearing Downcut Bit (10% off Code "SDC") - bitsbits.com/product/dnc250ft-downcut/ref/6234/
●Skinny Top Bearing Upcut Bit (10% off Code "SDC") - bitsbits.com/product/srf250ft-upcut/ref/6234/
●All Bottom Bearing Pattern Bits (10% off Code "SDC") - bitsbits.com/product-category/whiteside-router-bits/straight-cat/template-pattern/
●All Top Bearing Flush Trim Bits (10% off Code "SDC") - bitsbits.com/product-category/whiteside-router-bits/flush-trim-router-bits/ref/6234/
●Bits & Bits All Bits (10% off Code "SDC") - rebrand.ly/njveuj3
●MicroJig Cleaning Station - store.microjig.com/products/bladeclean-blade-and-bit-cleaning-system?sca_ref=1307061.sFIyHjmHS3
●Other AWESOME MicroJig Products - rebrand.ly/c47dewh
●Cleaning Solution 1 - amzn.to/3sEEVmf
●Cleaning Solution 2 - amzn.to/46pz16i
●Cleaning Solution 3 - amzn.to/49HKLnx
●Cleaning Solution 4 - amzn.to/49M7ZZO
●Cleaning Solution 5 - amzn.to/3sEEVmf
●Pica Pencil Bare- amzn.to/3G6gu4j
●Pica Pencil & Multi Color Lead Refills - amzn.to/3G98780
●Pica White Refills - amzn.to/3MNm3IE
●All Pica Dry Products - amzn.to/3QJFAe9
●Kreg Drill Guide - amzn.to/3MS20IX
Thanks for the cleaner bucket idea. Definitely need to keep blades and bits clean.
Searching Yoshino B2000 SST give me LiFePo4 powerpack which is not a solide state battery. Are yoshino sst discontinued?
I don't see a link for Ostrich feathers.. 🤔
I was excited to check out those ostrich feathers you suggested too, looked handy & I couldn't find them anywhere. Maybe you can provide that info next time. My kid would love using it when working with me.
I'd like to point out that you have been lead up the garden path with the battery buzzwords. There is no viable "solid-state" battery on the market in any commercial form yet, and not likely to be for many years, the best we have at the moment is LiFePO4. As for being "the only one" when it comes to solid state electronics, this is also demonstrably false. We have been making and using solid state inverters for 30+ years, it doesn't make sense to manufacture them any other way, it's the cheapest and most efficient method of inverting power. A good example is your cheap after market car amplifiers, they have inbuilt inverters to step the voltage up from 12V to 60+V as this is what is required to obtain 60W+ RMS of audio. Before continuing to use the term "solid-state" please do some research on what it actually means.
Based on the advertising material you show there, it's a 1.1kW battery, in this package size there is zero doubt this is a LiFePO4 battery.
Interesting to see how the internet has taken the craft of woodworking and turned it into marketing.
Just like the guys selling shovels during the gold rush.
What a trip
That was the case long before the internet. Go watch a "This old House" and notice the product positioning. The woodshop guy hawked products as well. It's also prevalent in the DIY auto garage genre of shows.
THANK YOU! Noise cancelation is not hearing protection! My earbuds were $6,000,. . . ok, they are hearing aids, but the Bluetooth music through them is amazing because they are totally tuned to my hearing loss. That said, I often have to take them out when doing loud work to put in plugs, though sometimes, I'll shut them off and just put the muffs over them, that is, until I go to the range, where I use plugs and muffs.
Very informative video. While I've done little projects for years, I recently put a lot of my skills together while building out new shelving in the back of my new work van and number one tool I wish I had was a track saw, but lived with a set of straight edges, clamps and the tape measure.
You earned my subscription with this video.
Tool #11 that you need is a dustmask. Your dust extractor will still blow very fine dust back into your garage and not all dust is captured at the tool (even with Festool). I have a versaflo mask from my dayjob that I use at home while carpenting. Bit overkill maybe but it has a fan with filter, an option for earcaps with bluetooth (radio/phone), protects your eyes and if you get the welding face shield with it then your can use it for that too.
True. Silicosis is the new Asbestosis - every kind of stone cutting is going to be an OHS issue very soon.
Ho-lay! There may be other models, but the first “versaflo mask” I priced was US$1800! I’ll bet it’s good at that price! I’ll bet thereother good powered masks, maybe one that’s “good enough” for casual use, but less than the tablesaw I want to buy, used!
I'm in the same boat for being in a 1 car apartment garage, 1 outlet no breaker and never would've considered a PowerStation for running things like a planer or bigger tools. Definitely gonna be picking one of those up ASAP. Also gotta say, the dust collector in the rafters is genius!
I wonder if it would be possible to put an in-line breaker between the outlet and the main panel, that way the maintenance wouldn't have to come for evry tripped breaker.
Even if you already own a drill press the drill guides come in very handy for when you can't use a drill press. Like you said for the price its a no brainer!
Pica is great, BUT I'd recommend getting the HB graphite fillings immediately the B2 (or whatever comes standard) is very soft and you'll be sharpening after every single mark if you want a fine line.
Ostrich feathers are a surprisingly useful natural tool accessory. Cut to size they can make a great flap sander replacement.
Sounds way safer than when they're still on the ostrich that is trying to flap you with those same feathers.
Wow. You really packed a lot into this video. I've been a carpenter/cabinetmaker for over 20 years and I learned a lot. Peace out.
I have been using 1.1mm mechanical pencils for years. This was a result of the 1.1mm mechanical pencils we used in the Air Force.
My favorite has been a double ended twist pencils with regular, red, green, or blue.
I sand a lot of smaller pieces (from 2" to 12") and I use a machine anti vibration mat, I used one under a mini CNC and realized the surface is very high friction and I can throw a 5" round board on it and sand without ever touching it, now some longer narrow pieces do move a little (never more than an inch or so) so I do keep a finger on them but this mat is amazing and changed my sanding forever. I had tried the same mat in your video and yea, it just slid around but the machine anti vibration mat does not.
Great video. I just subscribed to your channel. I really admire guys such as yourself who are able to work with what they have- a small shop- and put out great work. I do believe this helps make people better woodworkers. Thank you for tips and suggestions. I also like that you are not bombastic in your presentation. Good work.
Ostrich feathers, great video. As a retiree woodworking and knife making which I do go hand and hand. Your ideas are point on keep up the good work man.
I emphatically agree regarding the woodpecker track saw Square! I have had mine for about three years, and I have never used it for anything other than 90° cuts. Unfortunately, TSO‘s Square was new at the time if it was available at all. If I could do it over, I definitely would’ve went that route. Having said that, I will be getting their parallel guides.
Lovely tools...
One small tip, if your limited in power and have to wait before the fuse is replaced you can also put a breaker circuit in your shop, preferably just a bit lighter so that one breaks before the inaccessible one does. I did that in my shed because I found walking from the end of the garden to the actual breaker box costs me too much time, yeah I'm lazy ;)
Of course the power bank is still super handy there, but I'm not sure if it will power all of my stuff like compressor, welding machine. But thanks for the idea, combining it with the actual net power will help in certain situations.
Ostrich feathers made into a duster always worked well for cleaning around the shop. Love your vids, keep them coming!
for the router bits, when looking for them online they are called compression bits. you can also get end mills like that. keep in mind those are amazing for laminates, plywoods, and yeah. hardwood (although straight honestly works... just fine for hardwood). in the video i saw you use the compression bit on mdf.. that in my experience decreases the lifespan by ALOT. those tools are usually sharpenable 2-3 times but the mdf really tears it a new one and you will not get the best return on your investment. keep an old one for mdf, it doesnt require sharpness really anyways, just the shearing angle to get the surface nice and clean.
my sister got me some earbuds last year that are pretty great, they block out just about all sounds and i can use them while running my chain saw without any pain in my relatively sensitive ears, they have great sound quality and you control your music/book by tapping them
Thanks for the new track saw square idea- for $189 bucks.
I built my own from scrap basically for free and it works great!
Merry Christmas and thank you for the video.
Right!!
HOLY SHILL!! 30 minutes of sponsored ads in a 24 minute video
You're absolutely right. This guy is shilling. He's not a professional wood worker, except on UA-cam.
Never met a carpenter who use a trac saw. At lease not on the job site
Lol. Funny comment, but just because he may not have bought ALL those things does not make the info and recommendations any less valid. What would help would be a video on what is not so helpful. The only tool I regret buying in 40 or so years is a Port-a-line. It’s drill attachment to make perpendicular holes. I used it one or two times since I’ve had it. I have a drill press I bought used and I’ve used it many times since then. I will never be without one again. Having said that it’s not real convenient for edge drilling or large heavy pieces of wood or steel.
Is it too late to enter the contest?
I dunno. I walked away with a plan to buy that pencil!
I've always been fond of using Ostrich Feathers with a bit of water and low volt electric to make unique patterns
Quality video and audio, very well spoken, informative and a joy to watch, thank you! Keep it up! Admire your devotion in a confined space.
14:00 Those mats work perfectly. Your problem is that you have both, a very smooth table top, which most do not. Also you have a rather dirty table top, at least you did when you "tested" the mat. If you did not have either of these issues you would have a much better experience. Basically the dust is acting like a lubricant, yes, dust is a lubricant. Just check out the graphite dust in your torch converter. Anyway, to easily solve this problem you can just wipe your table top with a slightly damp cloth. Then wipe the side of the mat that with be facing down with the slightly damp cloth. This should remove the majority of the dust and prevent it sliding around on you.
"Well its a wood working shop, its going to be dusty". Yea, good point, but it almost seems like you set that up on purpose to make the mat look like it doesn't work just to promote that other product. Not saying thats what you did, but intentional or not you created the one situation where that mat would not work well which is also very easy to solve in less than 20 seconds.
Getting a large pencil lead holder is quite helpful. Can't speak for the one demonstrated in video, but getting a 2mm lead holder in general is great. Durable tip when marking, lots of different colors available, and the lead holders are inexpensive enough to have a few for quick access to different colors.
I have a 3mm mechanical pencil I got from Temu. I haven’t had a need to use it yet, but I’m sure it’s much better than the ever breaking thin crap we’ve all used. I’ve used carpenters pencils for decades. I can sharpen them to a needle point with a utility knife.
For what it’s worth I have that exact pencil and it’s hard to go back to something else. I like mine. For $5 it’s worth it.
There's a similar one from a brand called Tracer, they call it a "Deep hole construction pencil" £15 gets you the pencil, holster (Has a sharpener built into the pocket clip instead of awkwardly stuck on the end) and a lead holder with 6 spare leads, add another £2 and you can upgrade to a triple pack that adds a permanent marker in the same deep hole style (For any Brits reading, Screwfix or Toolstation usually have them in stock)
No idea what the availability or price of these are in the US or elsewhere, but I learned of it from a US creator so I'd imagine they're available, I'll never use a normal pencil in the workshop again, in fact it tends to get used for any pencil task whether it's in the workshop or otherwise lol
I have a set of 3M Worktunes bluetooth hearing protection. They work exceptionally well with awesome range. I've taken phone calls while sitting on my Kubota garden tractor while it's running and they can hear me okay. There are times I would rather have something smaller to use like when I'm in the workshop. Thanks for suggesting the Elgin products. I'll look into them.
I also use the worktunes, and love the sound they produce. I prefer them over those things you stick in your ears (comfort), not to mention losing one of those small expensive pieces won't happen with the headset.
Elgin Ruckus are great, they actually stay in my ears unlike nearly every other in-ear headphone I've tried. I'd also say look at the Bora Centipede if you need to modify your work space a lot. Being able to set up a large work table for some jobs then teardown in a minute to make room for other stuff is great. Their workbench table pieces are expensive, but you can make your own.
I’ll check Bora out, thks. For plain earbuds, not hearing pro, I like QCY a lot: reasonable sound quality, very lightweight, cheap - TC-13ANC ~US$25.00, and they stay in my ears, unlike ibuds. Also, hate to say it, but Bose earbuds stay in well. Not ear-pro either though. Also not cheap. If I were to spen the $ for sound quality in earbuds, it would be for Sony. Also not ear-pro!
Checked Bora out - looks like some folks like their customer service…also looks like they have and need lots of practice. Take their straight edge clamp. Too many issues!
So many other creators make lists like this but THIS is a really good list!!
As a biker who loves to travel a lot, the Rebel ear protection looks great. I will look into them for my big 2024 ride.
Grip it like nobody is watching.
Thanks Eric for this list. I own many of these items, but now have a few more for my wish list - just in time for Christmas. Bonus, most are low priced & almost all will fit in my stocking (getting the hint santa?). Seriously, thanks for putting this list together. I always learn something from your videos. Today’s practical tip was leaving a ~1/16” gap between tracks when connecting them. I haven’t needed to connect my tracks yet, but now I know what to do. A smart person learns from their mistakes. A wise person learns from the mistakes - of others….
consume, consume, CONSUME!
Ostrich Feathers work great for a lot of different applications. Thanks for the ideas and video.
I like that you do everything in a small shop like most of us. Great channel.
Was waiting for that one at the end.
Mum says good job by the way! 😉🤣😂🤣
I've always found ostrich feathers are great for sweeping up saw dust from behind my machinery. The Pica marker is definitely the best marker I've used.
Ostridge Feathers are a poor substitute for down in my winter underwear! I wish I had seen this video before I installed a new subpanel to supply power to all my tools even though I only use them one at a time. I am grateful for your sharing knowledge and the method you have to do so.
Hope to have a workroom set up in my basement before I turn 65 in January. Ostrich feathers will be great to clean the area. 🎉
This is a great video! I hadn’t heard of the track square thing before but I need one. I enjoyed the “grow up”. I enjoyed the frequent enthusiastic waving at the camera. Just generally helpful good vibes 😎 I’ve subscribed 👍
Ostrich feathers can help you clean blades. Also it match the color of the new coating on the router bits.
I bought 30 pounds of them and attached them to my table saw, thinking it would allow the saw to fly around the shop to wherever I needed it.
Sadly, the saw remained flightless. Who knew, right?
...ostriches have black, brown and white feathers, though. ;)
@@jamesrobertson9597well, there's your problem...ostriches don't fly.
I too have found them reasonably handy!
It Is a flightless bird after all. Just saying...Humming bird feathers might be more compatible with precision moves??@jamesrobertson9597
While I have never used ostrich feathers, I'm not surprised they work so well. Nature is amazing!
I have Pica pencils and the pens are awesome - I use them for absolutely everything! Even writing my son's name on his school clothes! I also have a drill block/guide and for what I do it takes up a lot less space than a drill press and even fits in the drills carry case easily too!
I've been using the OXGEAR version of the mechanical pencil for a few months now and I love it, so convenient.
My dad had a cabinet business and had a lot of Festool power tools. They are top quality tools. Unfortunately they are very very expensive too!
sometimes i think that ostrich feathers are the best for causing mass chaos when thrown from tall buildings. even more so if still attached to the bird! great list!
Ostrich feather. Thank you for your tips. I hope it works out for you to go full time. Watch out for what you ask for, we just might get it!
CHEESE. Best wishes young man! You are an inspiration to me for your perseverance. Happy holidays!!
At Woodcraft in Seattle, we (don't) hide our ostrich feathers in the drop-ceiling so when we need them we might forget where they aren't . . . I'm subscribed!!!
Ostrich Feathers work great! Awesome tips my friend!!!
Ostrich feathers are great... But I struggle with catching the little buggers!
OK... The pencil... Everything you recommended was cool, but I NEED that pencil NOW! LOL! Thanks for sharing!
Great suggestions. The links to the products was icing on the cake.
Ostrich feathers and the Kreg Drill guide always come in handy. Used the kreg tool to drill some tricky stainless steel tubing, was a little concerned at first, the drill guide made it a snap. (And 3in1 oil for the bit.)
Just a thought. Why not install a breaker/reset between your socket and your tools. No more calls to building maintenance.
I worked out of an apartment house garage for a little while. I worked for a cheapskate boss. He wasn't there to put up with the irate tenants yelling at me, who were paying good money for their substandard apartments. Do everyone, including yourself, a favor and either buy a suitable place or rent space in an area suitable for commercial use. Just holding off on a couple of Woodpecker tools will pay a month's rent. You can even rent a corner of someone else's shop for very little money, just make sure you can lock your stuff up. You are doing good and will be doing a lot better when you get out of that garage.
Came here expecting to find tools I thought I might need... left knowing that all of these are commercials Affiliate links in the description!
These are the tools that make my hobby projects look professional.
Some real gems here, thank you! Love the table and also the bit cleaning contraption.
I feel you. The people who upgraded my 1880 house, and built the garage certainty were not craftsman. The whole garage is on one 15 amp circuit. That includes the decorative lights that are built into the brick wall that serves as a fence. I can't run the window A/C and the air compressor at the same time. I barely get away with running the A/C and my 6" Atlas lathe at the same time. Every time that I forget I have to walk to the house, go to the basement, and reset the breaker.
I'm honestly looking in to setting the garage up with a solar charged battery bank.
23:02 If I have something too big to put on the drill press, I sometimes use double-sided tape to attach a circular bubble level to the back of my electric drill. Another way is to get section of 8/4 board and cut a V in the end of it and put your bit in the V to keep it vertical. With drill guides you're limited to the sizes in the guide. The V-block will accommodate every odd size. Use a 4/4 board for smaller bit sizes.
One pic worth thousands words. Make video, dude! :)
@@Thornik2012
uxzyRtHXN5Y - Kind of like this guy did but he made it harder than need be.
eSJtG947ZPk - This is similar to what I do. I find it easier to put a notch in a piece of wood with a band saw.
@@Thornik2012 Here's another one: Drill Straight Holes Every Time!
The most important item mentioned is by far any of the hearing protection.
Just ask anyone with tinnitus and or hearing loss.
Hearing loss is great when your going to bed, but not so much when trying to have a conversation with someone or watch TV.
🎶 click click punk now you’re thinking oh sh!t, quit while you’re ahead before I fill you full of lead🎵
That’s the house of pain/cypress hill jam.
Great video dude!
Ostrich feathers make great Christmas decorations.
Will definitely be looking into a couple of those items! Thanks, thanks for the video
Normal mechanical pencils come in thicker lead than 0.5mm which I used for years and they break all the time. I now use a 0.9mm for woodwork as well as sketching and general writing. I buy the Pentel Twist-Erase, great eraser too. They basically never break. Plenty sharp for general writing. Although the white lead pencil that writes on anything looks fantastic.
There is a part of me that does wonder how you came up with ostrich feathers, but I am content in not knowing. Thank you for the great share outs!
+1 for the corded hearing protection + Earbuds. The FIRST time I used some without the cords that hang around my neck, one fell out of my ear, and ended up going through the blades of my table saw....RIP.
If you have problem with breaker tripping in technical room you dont have access to, just make your own IP96 breaker box that get power from the one outlet, and you can then put multiple outlets after that breaker. If it trips, it should only trip that one, while allowing all your tools being connected, just dont go over the limit. Usually machines take most power when starting so you might consider making capacitor bank to give that little extra boost of power when starting, though talk to your local electrician about this and those big caps can cost a lot. Alternatively ask your building management if they could pull another wire and breaker from the technical room for your garage, specially if you are willing to pay the bill for it, or your landlord is.
Try Bose noise cancelling over-the-ear headphones. I did about 2 hours of sanding last night and literally had to lift it off my ears to see if the shopvac was really on while jamming to my fav tunes.
Agreed on the boring factor without music!
The Ostrich feathers did work as you suggested, but that damn bird nearly killed me getting them, the people at the zoo were pissed!
Was the Yoshino a sponsorship? it was just very specific in its wording and details
Ostrich feathers are a decent substitute for goose quill for all your permanent inking/marking needs.
you should definitely do a video on how you manage your electricity and outlets... I also work in a one car garage with one outlet and would be curious how you get things done
Ostrich feathers... very informative video. I will be purchasing some of your recomendations!
Hello, I enjoy your videos they are very informative for me since I am building a shop in my garage. I bought a workbench with dog holes in it but my bench dogs do not fit in the holes. The bench dog shafts are 19 mm, is the UJK reamer/chamfer tool to large for my bench dogs?
Thanks, Tom
Enjoyed the video. Only thing I disagree with is the no drill press. Bench tops are inexpensive, they don't take up much room and a god sent when you need one.
Thank for sharing. But I really wish woodworkers can keep coming up new ways /setups to use their fancy tools. Is it really that hard to design a table setup to use track saw for repeatable cuts instead of keep buying these not so cheap but really limited tools?
I think all the ostrich feather comments are hilarious. Thanks for putting this list together. I've ordered several of the items already! Happy Holidays to everyone!
A lot of those Festool tools, look like you're buying tools, just to buy more tools. This is akin to creating more work for yourself ( something that I generally try to avoid ). In most engineering circles, the DRY principal is quite effective, and repeatable template patterns provide the most efficiency when used in larger quantities. I'm pretty sure that you could address many of the problems illustrated, with less cost, less effort, and higher ROI.
Great video, have learned some new things I wish could buy now, but eventually will be buying some of these, Chuck
Hey Sir, I think you are my favorite subscriber on UA-cam. I found you while up at 2 am feeding my kiddo. You have a way of connecting with the camera. Your information seems very helpful, trustworthy, and genuine. Keep making videos. I have been wanting to pick up woodworking for a good three years as a hobby. I keep making excuses on not starting. I think as a result of this video I may finally start. Thank you!
Ostrich Feathers - another informative clip, well done!
For hearing I'd also reccomend Plugfones! I've used them for over a decade in the shop and on my motorcycle
Ostrich feathers!!! The Pica pencils sound like a new take on the draftsman mechanical pencils of the 70’s. We had a desk spinner with a sandpaper cone inside to keep them sharp. Definitely recommend HB or 2B hardness to keep the point longer.
When it comes to the Flush Trim router bit, I actually would recommend the newer models that also utilize the carbide inserts similar to the helical cutter head used in planers
Just found your channel. Not a wood worker, just an enthusiast. Bought the pica pencil through your link and will likely get a couple other things. Also did the ostrich feathers. Great video. I subbed. Merry Christmas.
Ostrich feathers, come in handy for many things…. They make pencil sharpeners for carpenter pencils, so they’re not really that difficult to sharpen but nice sales pitch for the pencil. Also, Raycon makes really good earbuds and their far less expensive than many others.
I don't do woorworking at all, but I love to see clever tools used in a clever way.
Eric, I just came across some of your older vids (I bet you can guess which ones) and that led me to the actual woodworking ones. I love them. I've subscribed and I'm looking forward to exploring your back catalogue along with your new stuff.
Having used several different BlueTooth "ear protective" earpods or headphones I found that they all have limited max volume levels on the volume controls. This is done to protect your hearing which I guess is good but means that you won't be able to hear your music or whatever while you are actually using your noisey tools.
I used to have one of those pens. But then my father came and helped me on a project the day before fathers day. He constantly misplaced his regular carpenters pen. So, I gave him my pen as a fathers day gift and I need to get a new one. Much more convenient than tying ostriche feathers to the pen to find it!
Hi there, I'm a first timer to your channel and I really enjoyed this video. Can you please share the type and/or brand name of your central metal work table?
I've never done woodworking and don't think I plan to in the future - idk why I watched this whole thing, but I did and I liked it
Have you tried balancing the workpiece on Ostrich feathers? I find they stop the workpiece moving. Top tip; remove from the Ostrich first.
Nice, I wonder if that dry pen will help me out with my low vision. Sometimes it can be hard to see my mark.
The compression bit is a great tip. I make cabinets and we often have to cut a panel or counter top with a router in the field and it would be nice to not worry about laminated edges
i would prefer flush trim bit with swappable inserts with a top bearing so you can use the bit for groove cutting still
That's so generous of you to make an actually decent useful list even for beginners like me. I wish I could afford those Elgin, my tinnitus and my tools don't get along well... Only complaint is that they don't show their sound curve, so we can't even tell how good/bad they would be for our music. I'm sure they're awesome for protecting our ears, but as they are technically marketed as true wireless earbuds, they should at least be transparent and show their sound profile somewhere.
tbh im using an old yoga mat as non slip thingy for sanding. works great as long as you put it on a clean table. if there's already a bunch of dust, the mat will happily slide on the layer of dust :D
Ostrich feathers...such a great tool to clean and sharpen my chisels. A great investment! Lol Thanks for the video!
Glad to have you back making videos!
Which tools highlighted in this video, (if any) are you not sponsored by or get a kick back from? For me, I find that recommendations that have no monetary influence behind then carry more weight.
Exactly. I stopped watching when there was no mention in the video description or beginning of the video of whether or not any of this is affiliated/sponsored content. As a result, even watching this is a hard pass.
Great video and you showed some dandy equipment. Thanks for a few ideas.....Take care, Bluefin.
Ostrich feathers are also an excellent tool to have in your shop.
Ostrich feathers 🎉 Love them for decoration - just pop a bunch in a large vase - voila
As an alternative to the Kreg Drill guide, I have and really like, the Big Gator Tools drill guides. They are a little more money, have a lot more drill bit sizes per guide, and are made in the USA.
Oh, and Go Bucks!