Great, and interesting video, but I’m sure you’ve done the same or similar before, that said I watch your videos over and over and I’m certainly gaining knowledge/tips etc. with every video.
adoro ferramentaria mesmo não sendo da área,trabalhos muito bem executados como o seu sempre terão um like garantido além da sua simpatia,um forte abraço !
Thought I would see more detail in setting the taper accurately for collets. Doing the Hex cleanup after the Collect work, Is it still on center? More detail on the hex clean up. Bet you could use a front surface grinder and think of all the tooling you could make for it. I love mine, and use it much more than I thought I would.
I will give you some tips if you turning set your carriage stop to lengh what you want to turn then engage power feed and work with them to make your work more comfortable . You have knife with good chipbreaker so use it properly take passes 2-3mm on diameter and the chips will break instead wind around your part and the surface will be better. When the chips wont brake increase your feed. Have nice day
Marabilloso. Meguta. Gracias.
Sei bravissimo eccellente inventiva complimenti meccanica di precisione ⭐️⭐️⭐️⭐️⭐️⭐️
Your videos are very interesting, thank you👍👍👍
Thank you very much for watching and welcome my friend!
Boa noite.
Como sempre você fez um excelente trabalho.
Fico atento a tudo que você faz, muito útil.
Abraços do Brasil.
Thank you and welcome to my channel!
Great, and interesting video, but I’m sure you’ve done the same or similar before, that said I watch your videos over and over and I’m certainly gaining knowledge/tips etc. with every video.
Thank you very much for watching and welcome my friend😉
8:00 how do you get the hexagon in the hole of the fixed part ? I don't understand 😮
Watch other video where he made a rotary broach tool.
ua-cam.com/video/LRgzFwXge3w/v-deo.html
@@johnm840 👍🤝🙏
Will watch It again. With cleaned glasses. Thx bro !@@CoolIdeasDIY-qv1nz
You are the best👍👍👍
Thank you, bro!
Very good work my friend👍
Thank you very much for watching and welcome!
adoro ferramentaria mesmo não sendo da área,trabalhos muito bem executados como o seu sempre terão um like garantido além da sua simpatia,um forte abraço !
Thank you and welcome!
Thought I would see more detail in setting the taper accurately for collets.
Doing the Hex cleanup after the Collect work, Is it still on center? More detail on the hex clean up.
Bet you could use a front surface grinder and think of all the tooling you could make for it. I love mine, and use it much more than I thought I would.
👍👍👍
Thats the way to do it, from Coventry 🇬🇧 .
👍👍👍
Thank you, bro!
Nice work sir
Welcome my friend!
Excellent ideas and adorable Pug. He looks very worried that you might start talking. Lol
Thank you so much!
Sehr geschickt und erstaunlich 👌
Thank you so much!
I will give you some tips if you turning set your carriage stop to lengh what you want to turn then engage power feed and work with them to make your work more comfortable . You have knife with good chipbreaker so use it properly take passes 2-3mm on diameter and the chips will break instead wind around your part and the surface will be better. When the chips wont brake increase your feed. Have nice day
Thank you and welcome my friend!
Fantastico 👍😀
Thank you so much!
Forget the bad points but OCD cleanest workshop
Well I admire that
ماشا۔اللہ۔تبارک۔اللہ❤❤❤❤
Hello my friend, welcome to my channel!