I love it. Though I would probably have put in a rheostat along with the power switch in order to allow you to control the speed in case you ever want to use the wire brushing on lighter materials that higher RPM might damage instead of clean.
Great idea, I really need to make one of these .you can get hurt badly useing a spinning wire wheel. Your tool makes it very safe. Was that a 3 phase motor? The larger capacitor was used instead of the smaller one. I didn’t understand how you could wire a capacitor into a 3 phase? Or was it a single phase motor. Thank you for showing your talent.
Definitivamente es un muy buen trabajo. Solo varios comentarios: 1) la potencia del motor debe revisarse (checar el amperaje real), colocar un arrancador con relevador de sobrecarga. El interruptor parece de baja capacidad (los platinos se dañan pronto) Colocar un mecanismo que permita el avance, pero no el retroceso, ya que en trabajo continuo o piezas largas será difícil de retener y el cansancio puede generar un accidente.
You should feed on an angle or even at a right angle against a fence/support with the pressure against the fence. As it is, this is not much of a tool. Feed would have to be much slower to be effective. I think a belt sanding device in place of the wheels would be much more effective. Wire wheels suck hard on flat surfaces. This machine isn't even touching the mill-scale beneath the rust.
Super! Except I would have made the motor carriage to be spring loaded and more easily adjustable. Spring loaded why? Because the lateral load being applied to the motor bearings would be reduced and also to negate too much overload and stall caused by any sudden gripping of material as seen at the end of the traverse in this video demo near the end. Great concept and definitely can be easily improved upon for anyone interested in making something similar! 👏🏻
you have single phase outlet you should use single phase 3 horse power motor it will work way better than converted three phase one. but nice work man👍
Ciao. Se il motore che hai usato è asincrono trifase, trasformandolo in mofase inserendo un condensatore, perdi almeno il 30, 40% della coppia. Un deciso miglioramento potresti ottenerlo interponendo fra motore e alimentazione un variatore di velocità con ingresso di alimentazione monofase e uscita, verso il motore, trifase. Otterrai solamente benefici: nessuna perdita di coppia, possibilità di variare il numero di giri del motore e rampa di partenza, in un tempo programmabile, da zero alla frequenza nominale del motore, o a qualsiasi frequenza impostata.
but the capacitor is invalid for a 3 phase motor. The Motor has not enough power on one phase. A better solution would using an one pahse to three phase inverter, who generates the three phaseof ac current. You are able to controll the speed of the motor as an additional advantage. I also would like to add guide rails left and on the right side, who prevent the slide the material out of the roller track. Additionaly - the switch is not water proofed and you cansee slots between switch and cover plate. Water will sucked in by the capillary effect. Where is a emergency stop switch? Your idea ist great and most of the mechanical construction is good handcrafted. But this is electrical unsecure and this must not be. Remember that you have also just one life...take care
Se não fosse o famigerado clickbait, até passava! Dizer que "ficou melhor do que na loja" foi forçar muito mesmo! Na verdade ficou bem meia-boca! 1. O motor não tem potência suficiente. 2. A ausência de um suporte na ponta do eixo vai destruir os rolamentos do motor rapidamente. 3. Pelo visto foi usado um capacitor aleatório, sem se atentar ao que seria de fato adequado ao motor. 4. A chave liga/desliga não poderia ser pior escolhida, é absolutamente inadequada. 5. Cadê o rele de sobrecarga para proteger o motor? Resumindo, é uma gambiarra que mal chega a meia-boca!
Competence, precision, the right tool and the end result is perfect. Such is a professional who understands his work.
Some mighty fine whittling there .
Молодец Михаил, хорошую чистилку сделал, и заснял хорошо.
nice bild !
cheers
ben.
EXELENTE HERRAMIENTA....SALUDOS....BENDICIONES
Creaste una gran herramienta te felicito saludos desde Uruguay 🇺🇾 🇺🇾🇺🇾👏👏👏👏
Thank you!!!
Perfect tool
Nice rust cleaner. We shared this video on our homemade tool forum last week 😎
Kreatifitas yang bagus ,
Good machines, good tools, good idieas make perfect products. I left my like 👍 for this thing. Thank for showing your amazing job.
Thanks!!!)
I love it. Though I would probably have put in a rheostat along with the power switch in order to allow you to control the speed in case you ever want to use the wire brushing on lighter materials that higher RPM might damage instead of clean.
The only thing that would make this video any better is if you would talk about what you're doing
Great video sir 😊
Sei un GRANDE !!!
Great job, man!
Está muy buena ❤💪🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻😅
Great idea, I really need to make one of these .you can get hurt badly useing a spinning wire wheel. Your tool makes it very safe. Was that a 3 phase motor? The larger capacitor was used instead of the smaller one. I didn’t understand how you could wire a capacitor into a 3 phase? Or was it a single phase motor. Thank you for showing your talent.
excelent !
That guard is going to be a constant irritation.
Ark flash put away fron the sreen sti ... Great build ...
Wow bery good boss
awesome work 😁👍
Thank you!)
super realisation beau travail
Would it not be cheaper to buy one and probably more efficient.
rất hay
Definitivamente es un muy buen trabajo. Solo varios comentarios: 1) la potencia del motor debe revisarse (checar el amperaje real), colocar un arrancador con relevador de sobrecarga. El interruptor parece de baja capacidad (los platinos se dañan pronto) Colocar un mecanismo que permita el avance, pero no el retroceso, ya que en trabajo continuo o piezas largas será difícil de retener y el cansancio puede generar un accidente.
Je n'ai pas vu cela en magasin ainsi que l'outil de moletage
You should feed on an angle or even at a right angle against a fence/support with the pressure against the fence. As it is, this is not much of a tool. Feed would have to be much slower to be effective. I think a belt sanding device in place of the wheels would be much more effective. Wire wheels suck hard on flat surfaces. This machine isn't even touching the mill-scale beneath the rust.
Este vídeo es genial no hace ni una sola medición y los rodamientos entran clavados etc etc
Super! Except I would have made the motor carriage to be spring loaded and more easily adjustable. Spring loaded why? Because the lateral load being applied to the motor bearings would be reduced and also to negate too much overload and stall caused by any sudden gripping of material as seen at the end of the traverse in this video demo near the end. Great concept and definitely can be easily improved upon for anyone interested in making something similar! 👏🏻
you have single phase outlet you should use single phase 3 horse power motor it will work way better than converted three phase one.
but nice work man👍
Ciao. Se il motore che hai usato è asincrono trifase, trasformandolo in mofase inserendo un condensatore, perdi almeno il 30, 40% della coppia. Un deciso miglioramento potresti ottenerlo interponendo fra motore e alimentazione un variatore di velocità con ingresso di alimentazione monofase e uscita, verso il motore, trifase. Otterrai solamente benefici: nessuna perdita di coppia, possibilità di variare il numero di giri del motore e rampa di partenza, in un tempo programmabile, da zero alla frequenza nominale del motore, o a qualsiasi frequenza impostata.
Não assisto vídeo que fica com um saco de propaganda antes de começar!
Un monton de herramientas importantes y cuando tuvo que hacer rosca lo hizo con la terraja . y el torno ???? 😂😂😂😂😂
needs a vac behind it
Magari se la presa di corrente ce l'avessi sulla sinistra quello che pulisci non ci andrebbe a sbattere
🕵️ Something is Wrong 😇🙏🔊
отличная модернизация устройства Скитальца
Co to za niekonserwowany złom, to ma być tokarka ?
but the capacitor is invalid for a 3 phase motor. The Motor has not enough power on one phase. A better solution would using an one pahse to three phase inverter, who generates the three phaseof ac current. You are able to controll the speed of the motor as an additional advantage. I also would like to add guide rails left and on the right side, who prevent the slide the material out of the roller track.
Additionaly - the switch is not water proofed and you cansee slots between switch and cover plate. Water will sucked in by the capillary effect. Where is a emergency stop switch? Your idea ist great and most of the mechanical construction is good handcrafted. But this is electrical unsecure and this must not be. Remember that you have also just one life...take care
Sorry to say this machine is not safe
Explain please.
tiempo y dinero perdido
better result with a grinder useless build👎
Fácilmente lo hago con la amoladora sin construir una estructura inútil.
🤕🤕🤕🤕🤕🤕
Se não fosse o famigerado clickbait, até passava! Dizer que "ficou melhor do que na loja" foi forçar muito mesmo! Na verdade ficou bem meia-boca!
1. O motor não tem potência suficiente.
2. A ausência de um suporte na ponta do eixo vai destruir os rolamentos do motor rapidamente.
3. Pelo visto foi usado um capacitor aleatório, sem se atentar ao que seria de fato adequado ao motor.
4. A chave liga/desliga não poderia ser pior escolhida, é absolutamente inadequada.
5. Cadê o rele de sobrecarga para proteger o motor?
Resumindo, é uma gambiarra que mal chega a meia-boca!