Отличные приспособления! Мне особенно понравился смещающийся центр для обработки конусов. Он более практичен, чем остальное! Молодец! Аккуратный, педантичный, любящий своё дело человек! Лайк, подписка, уважение!
Information. When you grind on the rails the grinddust will over time ruin them. The consequence will be that your lathe bed will be less precise. 0.1mm out or more. So maybe do yourself a favor and protect the bed against grinding dust.
At the 7:00 mark, why did he put a dead center in the chuck and turn the shaft between centers? The end of the shaft is not tapered, why not just put it in the chuck?
Hi, if I had placed the piece to be machined directly on the spindle, I would have obtained a cylindrical machining, at most a taper obtained thanks to the inclination of the turret.... However, to obtain long tapers, it is necessary to offset the part starting from the spindle and then offset the tailstock, with this tool, the work is much quicker!
Great Ideas, I learned a lot I didn't know. The one thing I noticed was you were waring gloves. I hope you were not running the lathe with your gloves on.
На токарном станке долбить паз не рекомендуется категорически, токарный станок не рекомендуется с использованием фрез - так как бабка не расчитана на упорные цыкличтскте нагрузки. Нужен долбежные -купи, нужен Ф -купи и не еби товарному станку подшипники и каретки.
да первая приспособа в принципе не рабочая, поскольку нельзя менять высоту втулки штока относительно крепления шатуна к маховику, она тупо клинанёт. а какой смысл в ерзанье на одном месте...
Какой хороший человек!!!❤
Сделал сам и поделился с другими!
Молодец! Спасибо и уважение!
Great Work Thanks for Sharing !!❤
Awesome video!!! Thanks for posting this!
Bravo ,sempre un grande piacere vedere le tue geniali lavorazioni.
Отличные приспособления! Мне особенно понравился смещающийся центр для обработки конусов. Он более практичен, чем остальное!
Молодец! Аккуратный, педантичный, любящий своё дело человек! Лайк, подписка, уважение!
Siempre buenos trabajos, muy prolijo y funcionales , saludos
Sembrerebbe bello vedere i tuoi ottimi progetti
Information.
When you grind on the rails the grinddust will over time ruin them. The consequence will be that your lathe bed will be less precise. 0.1mm out or more. So maybe do yourself a favor and protect the bed against grinding dust.
Последнее приспособление называется Пиз...ец станине😂
И здравствуй шабер.
Merci Tres bons outils !!!
Interesting. Very nice work
Ferramenta que todo torneiro precisa ter: UMA FRESADORA! 😂😂😂
Повеселил😂
falou toda a verdade tamos juntos
Excelente trabajo
😊Bardzo mądrze zaprojektowane przyrządy do wykonania kuli i zaokrągleń😊oraz do czyszczenia zardzewiałych elementów na tokarce😊
Me encanto el accesorio para hacer conos
The abrasive powder from sandpaper is very bad for the machine guides. I see that you are not protecting them at all.
good job 👍
Perfeitas e funcionais,só faltou usar pontas esféricas no deslocamento para fazer o cônico.
последняя приспособа не нужна, если не хотите попрощаться со станком! Никогда не пользуйтесь абразивным инструментом на станке!
good job, thanks
At the 7:00 mark, why did he put a dead center in the chuck and turn the shaft between centers? The end of the shaft is not tapered, why not just put it in the chuck?
Hi, if I had placed the piece to be machined directly on the spindle, I would have obtained a cylindrical machining, at most a taper obtained thanks to the inclination of the turret.... However, to obtain long tapers, it is necessary to offset the part starting from the spindle and then offset the tailstock, with this tool, the work is much quicker!
@@newtech5042 OK I understand. Thank you for the reply
Да...... Как же наши деды без этого обходились?
Советская власть на каждый случай имела специализированный станок и мастера. Для работы! 😊
Great Ideas, I learned a lot I didn't know. The one thing I noticed was you were waring gloves. I hope you were not running the lathe with your gloves on.
Hi, thank you.... I only use the gloves to pick up the pieces I just turned, because when I don't use the emulsion, they get very hot!
Pas mal, la premiere machine !
Ça va probablement interesser Mc rond pour se l'enfoncer dans le rectum à la place de Bribite.
that last one will destroy the ways of your lathe
Аброзивная пыль сыпется на направляющие
cool 👍🏻👍🏻
Sanding on a lathe without covering the ways? You have nothing to teach anyone.
Wonderful
На токарном станке долбить паз не рекомендуется категорически, токарный станок не рекомендуется с использованием фрез - так как бабка не расчитана на упорные цыкличтскте нагрузки.
Нужен долбежные -купи, нужен Ф -купи и не еби товарному станку подшипники и каретки.
да первая приспособа в принципе не рабочая, поскольку нельзя менять высоту втулки штока относительно крепления шатуна к маховику, она тупо клинанёт. а какой смысл в ерзанье на одном месте...
Все хорошо, но наждачка на станке это хана станку
Top👌
❤❤❤
i was so lost at 1:27 lololll
😎😎😎😎👍👍👍👍🤗🤗
Гриндер на станину - жестоко конечно, зашкуривание ржавой трубу по цене шлифовки станины... Ужос.
ой ля... по факту ничего ребята вам не надо из этого) если вы решили с дуру стать конвенциональщиком в 21м веке)
Всего один аксессуар: ЧПУ станок. А ржавчину точить на станке - угробить станок и себя/свой труд не уважать!
Super ⚙️🔩🗜️🔧🦾🦿 mechanizmy pomocniczy