How To Epoxy Coat Your Garage Floor - INCREDIBLE RESULTS!
Вставка
- Опубліковано 29 жов 2022
- #EverythingAboutConcrete #MikeDayConcrete #fixspalledconcrete #2023
How to epoxy coat a garage floor in 2023.
This garage floor had a lot of de-icing salt damage we had to repair before we could install our epoxy flake garage coating.
Some of the concrete was damaged about an inch deep. We used our two best repair methods to fix the spalled concrete. You'll see both methods in the video.
Then we applied our epoxy base coat, the flakes, and a polyaspartic top coat.
We've used these same methods on dozens of damaged garage floors to fix them and make the floor look beautiful again.
This is the best way to fix spalled concrete and the best epoxy garage floor coating, in my opinion.
Learn how to install epoxy garage floor coatings with flakes in my course below.
EMAIL ME - www.everything-about-concrete...
LEARN FROM ME - PRIVATE MEMBERSHIP AREA:
www.theconcreteunderground.co...
GARAGE FLOOR EPOXY FLAKE COATING COURSE:
www.theconcreteunderground.co...
MY STAMPED CONCRETE COURSE:
mike-day.mykajabi.com/offers/...
MY CONCRETE SLAB COURSE:
mike-day.mykajabi.com/pl/79570
FOUNDATION CRACK REPAIR COURSE:
mike-day.mykajabi.com/offers/...
GARAGE EPOXY FLOOR COATING COURSE:
mike-day.mykajabi.com/offers/...
VISIT MY WEBSITE:
www.everything-about-concrete...
USE THE SAME TOOLS I DO:
36" MBW POWER TROWEL:
imp.i284638.net/oeRMmn
ScreeDemon Gas Powered Vibratory Screed:
imp.i284638.net/4ZKEL
Screedemon Battery Powered Vibratory Screed:
imp.i284638.net/LzdBo
14' Screed Board for ScreeDemon:
imp.i284638.net/QOPDZM
MARSHALLTOWN SHOCKWAVE VIBRA-SCREED:
amzn.to/2tZ79ti
TOPCON LASER LEVEL:
amzn.to/2VrJ3zV
DEWALT PENCIL VIBRATOR TOOL:
amzn.to/2Km5Zis
INVERTER GENERATOR LIKE WE USE:
amzn.to/2XfWfwe
BULLFLOAT:
amzn.to/2U1Kx2F
HAND FINISHING KNEE BOARDS:
amzn.to/2TZmTUj
MAG FLOAT & STEEL TROWEL SET:
amzn.to/2IgmDOq
2" MARGIN TROWEL:
amzn.to/2G33KNn
CONCRETE PLACER OR KUMALONG:
amzn.to/2I00gxp
CONCRETE FINISHING BROOM:
amzn.to/2UytU2B
CONCRETE SCREED:
amzn.to/2WZxtwm
CONCRETE EDGER:
amzn.to/2GbGkEp
CONCRETE GROOVER:
amzn.to/2PaL414
BOSCH HAMMER DRILL:
amzn.to/31AHnaN
MY RECOMMENDED TOOLS PAGE:
www.everything-about-concrete...
SUBSCRIBE to my email list and get my FREE video guide on how to get the perfect broom finish on a concrete patio:
forms.aweber.com/form/44/2003...
Follow me on Twitter:
/ creteexpert
Follow me on Instagram:
everything_...
Follow my Facebook Page:
/ everythingaboutconcrete - Навчання та стиль
You guys are miracle workers ! Awesome job 👏 👍 🙏
As always, another great job
Looks great Mike, good as new!
thanks for your videos Mike! Sharing your knowledge has helped me do some DIY repairs with 100% confidence - thank you so much!
Great job guys!
Looks incredible!! Very impressive patching skills.. Maybe there is still hope for my floor.
Great job as always
looks awesome
Nice !
Excelente trabajo felicidades 👏👌🏻💪👊
almost looks as bad as my garage floor does, just needa add some large cracks in it lol, been looking at videos on how to repair it and urs are the best ive seen, cant wait for it to get a little warmer to i can start this project!
Yeah, good job! Night and day compared to what it looked like before! My question is the poly aspartic going to block the road salt? Thats what the pitting/spalling was probably from.
Nice work. Are the grinders Bosch? Thanks.
Day Style
Great job Mike! Wish your were in Missouri I would look you up. Hard to find good contractors anymore from my experience anyway. Keep up the great videos!
Thanks 👍
Another awesome vid!!! Where would I buy one of those little padded, wheeled things your grinder guy is using???
Very nice! I would like to have this done to my garage floor. I don't have damage like the one in the video but I do have a unique problem. The floor was not poured properly and let's in rain due to the slope being wrong. I need to float it which would take about an extra 1/2 to 2" of material. Is this possible? I'm concerned that a thin layer like that would be prone to flaking.
Great video! With how deep some of those spalls are, I'd bet that concrete isn't made to withstand freezing conditions - is the garage temperature controlled?. Salts also don't help haha. That epoxy coating will keep it well protected from moisture and salts, good work!
when erics on site we should have a clip of him thrown in there for fun, change it up a bit
Would I be able to use this same repair material for a driveway with some pretty bad spalling? This spring Im going to try to save our driveway as it gets worse every year.
Could this process and material be used on a sidewalk with servere deep Spalding ? Thanks Mike
Have you ever had a problem with self leveling cement chipping after you applied the epoxy? Also what epoxy product did you use to fix the pitting?
Could the spauling be caused by steel troweling it? My garage floor (12 years old) is starting to spaul and sounds hollow in spots.
👍
Will the epoxy stick to the old oil stains? Will grinding them help get rid of them
Is it possible to do your floor in sections? I have too much equipment to move out.
Is there a reason to hand grind this surface vs using a larger floor grinder? Is it due to the repair ?
I have a drain in the center of my garage. Of coarse the water from melting snow runs out the garage door and pedestrian door. I’d love to resurface the garage floor, but I want to fix the water flow issue first? Can you recommend a way to fix the flow and get it to the drain?
Hey Mike just wondering how much a job like that would cost a home owner, your work looks great
Never mind if I would have watched your video literally 15 seconds longer yoy went over that!! Lol
How much would a job like that cost ?
Eric was great at narrating, but boy do I hate road salt, but I guess if they didn't use it the crazy drivers would be slamming into everything.
I would think it would be cheaper to replace the floor
Eric lol
Why do you walk on as you roll it out
They’re wearing like cleated overshoes, like golf shoes, then the epoxy just fills in when they step out of it
Tell Eric to keep quiet. Otherwise great explaining and demo.
If this was my house I would want the stairs and that storage shelf removed or at least lifted to ensure complete coverage.......$6000....don't think so.....sorry....but I do like your channel generally
it’s a 2 car garage, plus he’s repairing the concrete. You also have take into consideration his drive time, if this out of his service area but yet he’s still helping this customer out.
Ya agreed, that floor was a wreck, he didn’t just bandaid it, he made the surface stronger and more dense, I don’t believe that was just road salt that made the floor spawl, I think when they finished it originally, they either bull floated it too many times or Fresno troweled it fight after, trapping bled water beneath the surface and it spawled, but the road salt didn’t help, there were some deep spawls in that floor, combination of both I think. And the other thing is, it’s expensive material, and it took him 2 days to do it, the do it yourself kits last about a year, I’m sure Mike uses at least a 5 year product and if you keep the floor clean it can last forever.
$10/sq ft. I would just have you pour a new floor.
Nope, don't like Eric, and on top of that, he seems to be the one who works de least, bla bla bla, with the blower he is good at it ......
another nice floor job, but that garage? Its like putting lipstick on a pig, and weeds all around front door?