DAJA DJ6 Laser Engraver: Engraving on glass material (Beginner's Guide)
Вставка
- Опубліковано 7 жов 2023
- I have been searching the internet for a while now, and I can't find a single video about engraving on glass using DAJA DJ6. So I have been experimenting and have found some tricks and tips on how to use this machine. It is hard at first, and you may end up wasting a lot of materials. Lucky for you, you don't have to make the same mistake that I did. So in this video, I am going to show you how to engrave on glass. I hope you like this video, and if you have questions, feel free to leave a comment. Thanks for watching! Please leave a sub, like and share!
Visit our Facebook page for more amazing products! / jabuprintingservices
Engraving software: drive.google.com/file/d/1IpCk...
Engraving Wooden Keychain: • DAJA DJ6 Engraver: Lin...
DAJA DJ6 Laser Engraver: shope.ee/3VIxhxSc52
Colored Paper: shope.ee/2AnbETV6Ce - Навчання та стиль
I apologize for the background noises. My house is along the road and its raining from time to time while filming. Please leave a like and subscribe if you find this video helpful. Thank you!
The work is excellent, thank you for sharing .
Thank you! Cheers!
I recommend a sand bag (filled with small beans) to position your glass. Just don't fill it too tight. Thanks for the video.
Yeah, I think that is more effective. Thank you for the recommendation Sir! I will try that the next time I engrave on glass.
Well explained
Thank you!
thank you for this videos
I'm so glad it was helpful!
Thank you for sharing....
You are welcome! Please leave subscribe and leave a like if this video helped you. Thank you!
Agradecido pelo trabalho
You are welcome! Please leave subscribe and leave a like if this video helped you. Thank you!
Muy ilustrativo el vídeo gracias por los detalles....
Mi pregunta es.....
Esta máquina hace grabado en plata .925??
Me alegro que te haya gustado. por favor deja un me gusta y suscríbete si este video te ayudó. En cuanto a tu pregunta, no creo que se pueda grabar en plata .925. Sólo se puede grabar sobre metal pintado. Solo quita la pintura, dejando al descubierto el metal que hay debajo.
I'm glad that you liked it. please leave a like and subscribe if this video helped you. As for your question, I don't think it can engrave on a .925 silver. It can only engrave on a painted metal. It only removes the paint, revealing the metal underneath.
Thank you for your good work
Can i use this engraver on stone please?
I haven't tried it on stone. But I will make a video of it so please subscribe and turn on the notification bell so you'll be notified for any upcoming videos 😊😊
Olá, tudo bem? Já vi alguns trabalhos em vidro que a marcação fica transparente. Que material é usado no lugar do vinil?
Hi Sir! Did they use the exact machine? Because Daja DJ6 need a black film to block the light so it can engrave. Some engravers does not need a black film to engrave, like fiber laser.
How do you get it to Bark when u hit start?
Do you mean "back"? I just click stop. But in case you mean like engrave 2 times in same spot, there is an option that lets you decided how many passes the engraver would do.
hello, can i use the machine to ingrave on clear acrylic sheets? if yes can you show us how? if no can you recommend a small ingraving machine?
I haven't tried acrylic sheets but I think it is possible. If I were to do acrylic, I would just treat it like a glass because if it can leave a mark on a glass, I think it would easily engrave an acrylic sheet. Just make sure you use colored paper. The darker, the better.
you can also try using black paint or marker to black one side out then engrave them wipe it all off in onewipea with rubbing alcohol
I will try it on my next project. Thank you! 😊
Hi! How long did it take for you to finish engraving the glass? Planning to buy one for personalized crafts.
Depending on the size of the design. The one on the video took 15 minutes more or less.
Where did you get the daga green grid mat?
It is included on the package when you buy the Daja Laser.
Would you provide an updated or alternative link for the paper? Could you tell me the name of it?
Hi. Good day. You can search for "Colored paper for engraving" on your online shop. I don't exactly know why, but they call it colored paper. I also struggled looking for this product because i don't know what it is but i bet you can find it by using those key words. I hope you have a great day! Cheers!
Can you please write the sitting spically the material what I choose?
If you are using the engraver app on your phone, I suggest you don't use the presets. Instead, use the setting I used in the video.
Olá, quais configurações você utilizou por favor ?
Hi. I used 100% on power and 80% on speed.
La oreja izquierda 🥲 pero todo lo demás bien 😃👌
Yes Sir! I manage to fix the issue by making the design smaller and adjusting the laser focus halfway from farthest to the nearest distance.
have you tried engraving on metal? the non painted one?. thanks
a very relevant question. author please answer
Hi. Sorry for the late response. Only fiber lasers can engrave on bare metal. DAJA DJ6 is not sa fiber laser but it can engrave on painted metal. Basically it only removes the paint, revealing the metal underneath. I will make a video, engraving test on painted and bare metal. Please turn on the notification bell because i will be uploading it soon. Thank you!
@@ajabujabu thank you sir
Do you know why i cam scratch it off after it is done?
Yes. 1. The laser focus may not be properly configured. Adjust it to the smallest point while the material is underneath. Use the black paper for more accurate adjustment. 2. The "power" and "speed" setting is not good. I recommend 100% power and 50 to 80% speed.
Can you send me the software windows for this engraver
drive.google.com/file/d/1IpCkDc49_al_SZ_d27L0BLQgDlSVBNhE/view?usp=drive_link
Hi po, pwede po ba ito sa mga glass tumblers?
Yes po as long as may colored paper po kayo na gamit.
How long did it take to make that
@@Lanebushmire I think it took me 15 minutes.
how about if I don't want the color in my lettering?
I haven't tried it yet but some people use sandpaper to get rid of the colored paper residue making the engraving white.
@@ajabujabusandpaper?
@@satriaane2113 Yes. Some people use 100 grit but they only sand the engraved part to avoid scratches on the whole design. And some people uses wire brush to remove the black color left by the colored paper.
a 130 dollar daja laser engraver seems to be ablento do even more stuff than a 3d printer i feel sometimes, everyone should have one
Yes i agree. Even just for a hobby, daja dj6 won't disappoint.
hello po , may I ask po if okay lang po ba na mobile lang ang gamit sa pagconnect sa engraving machine?
Yes po. Basta connected po yung phone mo sa engraver wireless.
What program are you using?
The software's name is Laser. It is in the included usb that contains the installer.
Cual es el nombre del papel?
They call it "Colored paper". I don't know why, but that is the actual name Sir. Lo llaman "papel de colores". No sé por qué, pero ese es el nombre real, Señor.
In the dishwasher this image from the glass does not laugh during washing ?😮
It leaves a permanent mark so I say that the dishwasher won't have any effect on the engraving.
What’s the name of paper?
They call it colored paper.
Software name? And from where i can download?
The software's name is "Laser". It is included on the package. The file is in the USB they provided.
Great vid po! Ask ko lang po if yung provided program ba ni DAJA gamit niyo for PC and wala naman po bang problems sa pag-install? Planning to get the same unit hehe 😅 Salamat po in advance!
Thank you! :) Yes Sir. Included na po yung flash drive with drivers for windows and mac. In case po na wala sa unit mo, pwede mo po ako imessage para mae-mail ko po sayo. Working din po siya sa windows 11 in case na yun po yung gamit mo.
And I want to add po before you buy, di po kaya ni DAJA DJ6 mag engrave sa bare metal, only on painted metal lang Sir. But still napakaganda niya pa rin na engraver. 😊
@@ajabujabuمطلي بماده ماذا ؟
@@user-ng5jb3gv2lthe black material in the video is called "colored paper". I don't know why but if you want to buy it online, that's the keyword you should use 😊
what about metal engraving?
Hi. Sorry for the late response. Only fiber lasers can engrave on bare metal. DAJA DJ6 is not sa fiber laser but it can engrave on painted metal. Basically it only removes the paint, revealing the metal underneath. I will make a video, engraving test on painted and bare metal. Please turn on the notification bell because i will be uploading it soon. Thank you!
bro, soak it for 15-20mins then remove easily.
I'll try that next time. Thank you!
Nakaka engrave po sa acrylic sir?
Hi. Yes po sir. Just make sure na lagyan nyo nung colored paper or black marker. Ang purpose po is para di tumagos yung laser sa acrylic.
Que parámetros de potencia y velocidad usa para grabar acrílico usando marcador negro?
@@montserratgarciavieyra2650 Yo uso 100 de potencia y 80 de velocidad. Pero puedes reducir la velocidad si quieres un grabado mucho más profundo.
Cause I watched this. I now know not to do it this way. Cermark spray is 100 times easier.
I guess you got the wrong idea, sir. As you can see in the video, I did not have any problems with the first engraving. The color paper is not the problem; it is the scale of the design plus the curved surface. Yeah, I know I should know better not to make the design bigger. I haven't tried CerMark spray because it's not available in my country. I hope I can try it someday.
Its the scratching with a Stanley knife. Surely its not good at all for a glass. But I do understand we can only use what we have to hand. And well if it works for you that's fine. :) it's just not for everyone :))
yup or just black paint in a lil 16 doar usb paintnsorayer
@@ajabujabuu must get a small motor and slowly rotate the glass on two rollers you can 3d print a machine that does that and use an existing spinning object like ur usb turn table
where can i get the cermark spray?
Who forgot to use their Safety Glass... @ajabujabu did!!!
My unit did not come with free safety glass so I don't really look directly at the laser. But when I have to check the engraving, I always use the green panel that has the same material as the safety glass. I don't know its name 😅