Guys forgot to mention the added trac bars from procomp, pro comp front skid plate and the trd pro grille with color matched surround. Yeah nice and clean tundra.
You guys should start doing a side by side comparison of stock model and lifted model to see the difference in height. Or maybe some measurements? since the side by side would be a little difficult because you need two of the same trucks lol.
Not taking sides but Tundra is a 1/2 with basically equivalent parts to all other 3/4 and 1 ton. So their build pretty bad ass. Plus they are actually the most American made Truck on the market.
501 N 503 It’s not American, the money goes back to Japan. And that piece of garbage Tundra is not equivalent to a F250 or F350, you must be smoking crack.
Lol this dude talking about tundras are garbage. Funny how you never hear anybody have problems with them though. This dude probably doesn't even have a truck.
Do not remove the front plastic on the bumper as he states the tires throw water there which causes the fog lights to burst due to the fog lights being hot from running then cold water touching them. I have replaced 4 sets of fog lights in the last 4-5 months and finally gave up on them and don’t have bulbs in the fog lights
I have a 2021 toyota tundra crew max short box I have a 3.5 inch lift and got some new 18×9 after market rims and running 35 inch tires how should I go about trimming my bumper and all in the front so I don't rub??????
I just bought a clean 13 Tundra. Its sitting on 35,12.50×20 tires. Vlears them great. My question is how can I tell if its a 4in or 6in lift? Cause I'm looking to upgrade to wider rims. Thanks
did you have to regear? I have a Tundra 2016 with 6 inches lift and 35s, went to do some light 4x4 and the passenger side cv axle came off the hub. Somebody told me that it is because anything bigger than 34s require to regear and that is the reason the cv axle broke. What do you think?
Let's say you bought a pre-owned truck recently with some sort of lift (in my case it has pro-comp shocks/struts front and rear, blocks and spacers) but you don't know exactly what lift height was achieved by the previous owner. How would you go about figuring this out? I'm pretty sure it's over a 4" kit but not 100% it's a 6" kit. It doesn't have all the fancy hardware of the current models like the lower suspension pieces, still has the factory upper arms, but everything else looks aftermarket. All I can tell you is I'm 6'5 and the truck is taller than me, and I can easily get my entire torso between the tire and the wheel wells with plenty of space. =)
Robert Fernandez yea but the resale value will still be better then chevy,ford or dodge. An the newer yotas dont have to worry about frame rust. The older ones did but toyota bit the bullet and recalled them. An replaced thousands of them for free to the owner. I love my tundra and its built here in america. Unlike others. Some people just cant afford a nice tundra so they hate....
Toyota should make their inner wheel wells larger. It should be like the Hummer. Or at least provide a factory TRD kit for people who want larger tires. That way their not destroying the resale value when cutting.
2018 Tundra CrewMax TRD OffRoad 4WD Mostly highway. Want that aggressive stance 20" and able to fit 35s while also still letting factory components (i.e. TCS, etc.) work. With a $6K budget
@@TheVilouboy Turning radius is reduced by a good amount when you run a 6 inch lift due to the addition of bigger steering stops to prevent from overextending the steering. If you can put up with that then go with either company. Heard of members say they had alignment and tire wear issues with the bds lift. I haven't heard that from pro comp users and I can attest to that because my dad ran 7-inch procomp stage 2 on his tundra with no issues at all.
I have a 2020 Crewmax 4x2. Just in height, is it the same on a 4x If I do a 6'' spacer lift, with 22x10 on 35s, & do I still have to trim, or should I go with 22x9 ??? (I really want 22x10 but don't want to trim, I prefer it clean)
Everyones version of offroading is different, does this setup go through fields/a bit of mud yes! Is it intended for rock crawling and prerunner jumping; no.
Hold on guys....35-12.50-20 is not supposed to go on a 12" wide rim. Only rated for 8.5"-11" wide rim according to the Toyo website 35-13.50-20 is ok for a 12" wide rim. This could be dangerous.
Heres a link to one of our videos, in here if you skip ahead to @8:00 we talk about how it is perfectly safe to mount a 12.50 tire on a 12" wide wheel. ua-cam.com/video/QnaF_Jsa50w/v-deo.html
No after martket uca needed with this lift. An angles are better then a 3inch lift due to the real diff drop. Bet the truck rides almost like stock and looks bad ass.
I just bought a lifted tundra. 6 inch off set. Should I worry about rocks being flung up by the tires and chipping the pain. If so what could I do to combat it
My truck is a 16', trd pro, 6" lift, 22" rims, 37" tires, owner for 6months... Love it. Just needs diff lock on rear axle
Is there a way I can seeee
I know there's an old post but do you still have that truck? Is there anyway I can see it? I'm looking to get that same exact setup but on an SR5.
Guys forgot to mention the added trac bars from procomp, pro comp front skid plate and the trd pro grille with color matched surround. Yeah nice and clean tundra.
Not to mention d.a.p
You guys should start doing a side by side comparison of stock model and lifted model to see the difference in height. Or maybe some measurements? since the side by side would be a little difficult because you need two of the same trucks lol.
Greg, we're starting to do a measurement as guys are concerned about their trucks fitting inside garages/parking structures!
Custom Offsets awesome! Thanks.
I dont even like Tundras but man this one is CLEAN AF!!
Best truck hands down!
Lol... what do you drive ford ranger? gdfo
Sean Nghiem No, but even a Ford Ranger is better than that Tundra garbage.
Not taking sides but Tundra is a 1/2 with basically equivalent parts to all other 3/4 and 1 ton. So their build pretty bad ass. Plus they are actually the most American made Truck on the market.
501 N 503 It’s not American, the money goes back to Japan. And that piece of garbage Tundra is not equivalent to a F250 or F350, you must be smoking crack.
Lol this dude talking about tundras are garbage. Funny how you never hear anybody have problems with them though. This dude probably doesn't even have a truck.
Do not remove the front plastic on the bumper as he states the tires throw water there which causes the fog lights to burst due to the fog lights being hot from running then cold water touching them. I have replaced 4 sets of fog lights in the last 4-5 months and finally gave up on them and don’t have bulbs in the fog lights
Why not build a plastic barrier to protect them
Nice Truck. I was wondering did you order the same tire for your spare or keep the same spare tire?
What a Dream
Solid stunning beast tundra ever
im looking for something just like that gotta be 4wd and i wouldnt mind white or black paint instead of a blue blue look nice though ngl
Looks really sweet
Nice, clean looking job. That truck looks awesome!👍
Bad A... do syder headlights adjust with the interior headlight knob adjuster?
Yes
Nice truck. I'd like to see that color with forged or chrome wheels and not blacked out. I bet it would look pretty kool. Maybe.
Sweet shorts Fuller
Upgrade those A arms, tow mirror, helper’s airbags! Clean truck
Do you need to regear because the size of the tires?
y’all need to do mine next i got a 2011 toyota tundra limited 6 in 35s
So clean
It's a beauty
Does anybody know what the total height of the truck is?
@@73kepakepa looks like a 6inch that’s what the title says
I’m bout to buy a 2016 tundra that sits just like that but it’s steel grey same wheels tires and lift, although the wheels are 22 inch I believe
I like that especially light bar on bumper , what size of that light bar ?
30inch
I have a 2021 toyota tundra crew max short box I have a 3.5 inch lift and got some new 18×9 after market rims and running 35 inch tires how should I go about trimming my bumper and all in the front so I don't rub??????
I have the same rims just on 33s I’m thinking of upgrading tires to 35s and 6 inch lift kit
Is it possible to fit an automatic food stamp on a built in foot stamp to make it stairways up & down ???
Fuller can’t pull off the Let’s go
I just bought a clean 13 Tundra. Its sitting on 35,12.50×20 tires. Vlears them great. My question is how can I tell if its a 4in or 6in lift? Cause I'm looking to upgrade to wider rims. Thanks
did you have to regear? I have a Tundra 2016 with 6 inches lift and 35s, went to do some light 4x4 and the passenger side cv axle came off the hub. Somebody told me that it is because anything bigger than 34s require to regear and that is the reason the cv axle broke. What do you think?
Dude that Tundra is badass 😳
Ima do this to my mom Sequoia, lol
That’s a bad ass truck man
Did you guys leave the leaf springs that came in the kit out?
They were re-used with an add-a-leaf, unfortunately we no longer sell this kit though.
I hate when lifted trucks are higher in the front. Make it level or keep the rake.
Looks better slightly higher in the front actually
Look up truck lean. It will make you hate people. Its the biggest waste of a truck you will ever see.
I think truck has old wheels on back bed that’s about 400 lbs that’s why has front higher
I have this same set up on my black 2014 Tundra 1794 with 100K miles. I want to sell it. How much do you think it's worth? I live in Dallas, TX.
I want to know if it is possible to use the same size of wheels on my 2019 tundra, but without lifting it
Definitely possible! However, you might have to trim some fenders to be able to take a full turn!
And what is the bolt pattern 2019 tundra
5x150!
Doubt it tires still rub slightly
Let's say you bought a pre-owned truck recently with some sort of lift (in my case it has pro-comp shocks/struts front and rear, blocks and spacers) but you don't know exactly what lift height was achieved by the previous owner. How would you go about figuring this out?
I'm pretty sure it's over a 4" kit but not 100% it's a 6" kit. It doesn't have all the fancy hardware of the current models like the lower suspension pieces, still has the factory upper arms, but everything else looks aftermarket.
All I can tell you is I'm 6'5 and the truck is taller than me, and I can easily get my entire torso between the tire and the wheel wells with plenty of space. =)
Damn. Someone should make a replacement for that cover delete in the wheel well. Protect that harness from mud and rock.
Gmon3y 142 It’s a junk Tundra, the frame will be rusted through before the harness goes bad
Robert Fernandez yea but the resale value will still be better then chevy,ford or dodge. An the newer yotas dont have to worry about frame rust. The older ones did but toyota bit the bullet and recalled them. An replaced thousands of them for free to the owner. I love my tundra and its built here in america. Unlike others. Some people just cant afford a nice tundra so they hate....
It is just a mall crawler anyway so they don’t have to worry about that
George Montes no need just put 1"1/4 spacer
on front bumper and leve the original plastic cover
Toyota should make their inner wheel wells larger. It should be like the Hummer. Or at least provide a factory TRD kit for people who want larger tires. That way their not destroying the resale value when cutting.
My tundra have a problem with the center support bearing somebody have tips I have
We recommend taking it to a shop to be checked out!
I'd really like to know how good are tundras? Never owned one they look sharp as hell but are they durable and worth buying?
Ron loves his Tundra! He says that's why they're so expensive is because they're worth it🤙
Clean.👍
What happened to Havok contest drawing?
Ya no shit wheres the drawing im in it.
The give away was live on facebook and instagram from Vegas!
Was the BMC done on this Tundra?
Can a 6 inch lift clear parking garages
what type of fog lights are you using on that truck
So a 4 in should fit those easily right?
Is that a paint job never seen blue tundra
No blue ribbon metallic 2015
Ain't got no hundos but here's a food stamp. Lmao!!
Cool Truck!
What’s your take on Pro-Comp vs BDS?
Both are great options depending on the situation!
2018 Tundra CrewMax TRD OffRoad
4WD
Mostly highway. Want that aggressive stance 20" and able to fit 35s while also still letting factory components (i.e. TCS, etc.) work.
With a $6K budget
@@TheVilouboy Turning radius is reduced by a good amount when you run a 6 inch lift due to the addition of bigger steering stops to prevent from overextending the steering. If you can put up with that then go with either company. Heard of members say they had alignment and tire wear issues with the bds lift. I haven't heard that from pro comp users and I can attest to that because my dad ran 7-inch procomp stage 2 on his tundra with no issues at all.
I have a 7 inch bds on my 2013 tundra. Ive put 110k miles on this lift and love it!
I have a 2020 Crewmax 4x2. Just in height, is it the same on a 4x If I do a 6'' spacer lift, with 22x10 on 35s, & do I still have to trim, or should I go with 22x9 ??? (I really want 22x10 but don't want to trim, I prefer it clean)
Why would you lift a truck without four-wheel-drive?
@@phantasmagoric3934 because he fucking can idiot
Awesome Build. did you have to regear. did this affect mileage? how about sound in the cabin while the windows are up? was it noisy? tyre noise
No, yes a little, not terrible, not very noisy.
I have a 2019. can I run a 285/65/18 cooper discoverer stt without lift?
I’d say with a level you’d probably be alright just be prepared to trim if necessary
I got a 2015 Tundra I’m doing a 3in front lvl kit what back space do I need on a 20in wheel and can I run 35 or just 33 tires @ 12.50 wide?
bit.ly/2jgrQX0 Check our gallery out here
Mint
What was the cost for this build?
Check out the links in description for pricing Sean!
Sweet color. My Tacoma is the same color.
What's the name of that color?
Can we please get some more Tacoma’s??????
How does something like this actually perform off road I love the looks but is it practical for off-roading?
Everyones version of offroading is different, does this setup go through fields/a bit of mud yes! Is it intended for rock crawling and prerunner jumping; no.
Custom Offsets so in short, the truck is probably more capable in stock form?
What about the exhaust?
Trd dual
The truck looks great and all just dunno feels like the tires are small on this beast
Nice!
Hold on guys....35-12.50-20 is not supposed to go on a 12" wide rim. Only rated for 8.5"-11" wide rim according to the Toyo website
35-13.50-20 is ok for a 12" wide rim. This could be dangerous.
Heres a link to one of our videos, in here if you skip ahead to @8:00 we talk about how it is perfectly safe to mount a 12.50 tire on a 12" wide wheel.
ua-cam.com/video/QnaF_Jsa50w/v-deo.html
Wheres the havok giveaway???????
We did it live on Facebook/instagram in Vegas at Sema!
Back40_Sportsman - nice wheels
What tire could i fit on a tundra with a 4" lift without cutting anything?
Vlad, check our gallery out for fitment help here- bit.ly/2msldly
Did you Fit any tires without cutting
The beats are straight 🔥. Custom Offsets killing the game 💪
Why is the front end taller than the back?????
It's not level!!!
Tires in the bed
Cause there's horse's in the back
Duh
How'd you guy blackout the badges on the 2015 Blue tundra limited?
D Smith Sr plastidip
You can buy black badge sets on ebay
MPG, CAI, programmer???
Carlos Reado 12, D.A.P TUNDED
Stock UCA’s with 6”. Ouch hope that’s safe
If it wasn't safe, we wouldn't install it and the manufacture wouldn't release it Kyle!
Custom Offsets I’ve been told and seen that the geometry is all incorrect anything over 3” on our tundras. With the stock UCA’s still installed
Thats people who don't get kits. Any spacer type lift over 3 inches will require new control arms.
No after martket uca needed with this lift. An angles are better then a 3inch lift due to the real diff drop. Bet the truck rides almost like stock and looks bad ass.
Want city you guys in
Appleton, WI
Ha ha Shawn uses $100s, Fuller has to use a $5!
No hunnndos.... All about the Benjamins baby
Tundra needs an inch or 1.5inch lift in the back lol
U didn't listen did you, dummy
Lol I agree. He did say its sagging because of the oldvrims and tires. If thats all it takes to lower the bed to level I dont want this lift kit no mo
Supercharged then this would be a raptor killer
Love it😍
What is the purpose for the Big Ass Rims?
The 18” Stock are PLENTY large enough..I HATE Big Rims!!
leggggggo
My question is how do ya'll afford this shit? How do you afford the gas? I know everyone who drives a truck isn't rich
Lol not that difficult
Hey was just driving behind you at the Wal-Mart in Lecanto. Your vids are dull at bruh. Get better music
Back is sagging down.
Looks horrible!!!!!!
Bill Peirce - could bc because there’s two extra wheels in the back as you can see from the video and also he mentioned this in the video fwiw.
All this money and skipped out on the lift. Pro comp is garbage. Toytec fox or icon king would have been better
Nice Truck. I was wondering did you order the same tire for your spare or keep the same spare tire?
I just bought a lifted tundra. 6 inch off set. Should I worry about rocks being flung up by the tires and chipping the pain. If so what could I do to combat it
Nice Truck. I was wondering did you order the same tire for your spare or keep the same spare tire?
Nice Truck. I was wondering did you order the same tire for your spare or keep the same spare tire?
Yes ordered spare