[Home Machine Hack]DeLonghi ECP 32.21 Steam Wand Replacement
Вставка
- Опубліковано 17 жов 2024
- Hack my small home espresso machine in to another steam performance level ..
Replace the original Steam wand with the parts for Rancilio silvia that was available on the online shop
That music will drive any coffee drinker insane!!!
At 0:15 seconds per loop and a 20:20 video it repeated over 80 times
It's actually tolerable at 1.5x speed tbh. It gives it a nice bounce.
At 1x it's torture.
Thank you!! This tutorial worked great for my ECP3420 model. A couple notes: removing the clamp that holds the hose in place and attaching the plastic piece onto the new steam wand were much harder than it looks in the video. Don't be surprised if it takes a bit of elbow grease to complete those steps! It's well worth it though! The new steam wand is a large improvement over the one that comes with the machine. Thank you for putting together such a detailed tutorial!
What should I do if the steam pressure is now very low?
@@grantapusdonald6105 tighten the hose clamp and then it should be good
Thank you so much for the tutorial, just did it for my ECP33.21.
2 tips for others, tested it myself.
1) when installing back the rubber holder at 16:00, do put some water on the steam wand itself for ease of installation.
2) at 16:30, do use the pipe leak tape to prevent steam from escaping.
Thank you!
this is honestly the best made disassembly tutorial I've seen
I just used this excellent tutorial to do the mod on an ECP3420. It was nearly identical -- the only two differences being that the 3420 has a nylon braid covered hose instead of the clear plastic hose in the model in this video, and the clip holding the hose onto the steam wand is not reusable on the 3420 as it is with the model in the video. The one in the video is a spring type while the 3420 has a clamp that might be reusable if you put a lot of work in with some fine needle-nose pliers but I didn't find that to be worth the effort when I was able to go buy a 3/8" spring clamp from Napa up the street for 39 cents. You can also get these at Lowe's, Home Depot, Ace Hardware, and probably every auto parts store. Get the 3/8" if you need one. I might have preferred the plastic hose because this very rigid braided hose doesn't allow the steam wand to be easily movable. It wants to be in one place and the hose doesn't move as you rotate it so I keep feeling like I'm at risk of dislodging the hose as I swivel it -- therefore I try not to move it. I may go back and replace that hose with a more flexible one.
Also, as shannong notes below, some steps are much harder than they appear in the video. It wasn't easy to get the hose off the original steam wand. Most of all, getting the white plastic piece off the old steam wand was pretty difficult and I absolutely struggled to get it onto the new one without damaging anything. I guess my hands aren't strong enough because I couldn't twist it on as you see in the video so I was stuck trying to use pliers but trying not to damage the piece -- not at all easy. It took a while and a lot of work.
Make sure you put the rubber thing back on the elbow of the new wand. You'll need it because it gets VERY VERY HOT. You will burn yourself on it if you aren't careful. It gets so hot that I can't steam milk without the milk baking itself onto the wand before I'm done, though having a clean wet cloth handy to IMMEDIATELY wipe after steaming is essential otherwise you'll be scraping it if you wait even a minute. And don't use a paper towel, especially not a dry one. The first one I tried just shredded itself and stuck to the milk and became part of the mess I had to clean off.
I'm still figuring out technique for steaming properly for latte art, which is harder than it looks. This wand mounts so that it's nearly vertical but most of the machines in the videos have wands that are at more of an angle so that the "whirlpool" can be established easily. Maybe I'll try bending the wand carefully so that it's at more of an angle. Has anybody else angled their wand differently or am I just missing a technique for using it when it's almost straight down?
Has your upgrade of this new wand come apart with use? The PEX clamp on the ECP3420 that it comes with stock is difficult to re-use and must be replaced with a new one and you need a special tool to do it. Just curious if your spring clamp has come undone inside the unit? Mine has come undone and sprays water on the inside of the unit however I used a stainless steel hose clamp. The problem with the Rancilio Silva wand is that it doesn't extend far enough into the unit as does the original wand when you put them side by side.
@@dr.j7912 I noticed the same issue with the Rancilio Silva wand. I decided to just go back to the stock wand rather than have it come loose and spray inside everywhere.
It’s been 11 months!!! How’s that latte art comin’ along😉
Hi Chris, I want to replace the steam wand on my delonghi COM530 (All in one machine) and am running into the same issue. The hose is a red braided hose and the clamps are PEX clamps. Do you know if the Rancilio wand will work on my machine? And do you still have any problems with the upgraded wand?
Hey guys, thanks for the above tips, I just replaced my steam wand on ECP3420. It almost took me an hour but the upgrade was totally worth it. So regarding the hose clamp, I used two zip ties to tighten up the hose and there are no issues so far. There is one comment down below that mentioned to use the table as a leverage to push the while wand stopper through up and same for the black rubber.
Just completed this replacement on my ECP3420. To make it easier to place the plastic ball onto the new wand you can use some light heat applied from a heat gun or the stovetop. Carefully heating the wand and plastic assembly helps to soften the plastic and make it easier to be push around the new wand curves.
This worked on my ECP 3420, the pipe clamp was different though, and couldn't be reused so I had to purchase some from the hardware store. I found it a lot easier to get the plastic piece onto the steam wand by pushing it against the lip of a table. The rotating and using only finger strength was too difficult for me lol. Thanks for making this tutorial!
What should I do if the pressure is now really low ?
Yes, thanks for the tip!
The table lip tip was perfect! Thank you
Thank you - this worked for me on the same model. Be careful not to drop a screw inside the machine. There's a hole in the floor and they fall through into the base and you can't easily get them out. The base comes off but it's held on with security screws.
I also found that once I'd pushed the plastic support onto the new wand it was too lose to grip the wand tightly so when you rotated the wand it wouldn't stay put. It should be a tight fit on the plastic so when you rotate the wand the plastic piece moves with it and that creates the friction to stay in place. I made a little shim out of a piece of a beer can (had to drink the beer first) and squeeze it in between the wand and the plastic. The new wand works much better; I still need more practice though.
That was incredibly helpful and thorough! Much appreciated!!
Looking how easily that guy disassembles the wand and puts off and on that plastic stopper (a half-spheric one) makes me feel so weak lmao.
It was a LOT harder to do the same with my machine and steamer. I think it's mainly because I've used a different steamer as replacement.
I even had to use a pliers and flat screwdriver as a leverage to put that stopper on my steamer.
Anyways, thanks a lot, this video was a great help for me.
I should put "Yours maybe easier of other ways" in the caption 😁
First of all, this is an interesting Video. I am using ESP 31.21 for 3 years, I think it is same as ESP 32.21. This machine has a small kettle, so its amount of hot water for making coffee or steam for whipping milk is less compared to higher-end machines. With a limited budget, it is recommended to invest in an Espresso grinder and use a single filter basket without pressure (9g), you will be able to make a 1:3 cup of Espresso coffee in 25-30 seconds.
(Because my English is not good, thanks to Google translate)
Lovely. Thank you! I'm headed to my workshop RN to try this.
At 9:30 you don’t have to re install the wand stopper clip? Thanks
Это отличный гайд и я очень благодарен автору за это видео, у меня все получилось (мне понадобился один час для завершения всей работы) ! Эта паровая трубка выдает значительно больше пара чем стандартная резиновая паровая трубка, даже если снять насадку Panarello.
Однако я хотел бы сказать о нескольких возможных проблемах.
- прежде всего, имейте достаточно инструментов под рукой. Вам могут понадобиться большие плоскогубцы и возможно, накидной ключ (ключ сантехника);
- очень аккуратно вынимайте ручки управления паром и ручку переключения пара/запуска приготовления кофе. Они сделаны из плохого пластика и я сломал одну из ручек;
- внимательно следите за шурупами, некоторые из них них длиннее других и должны быть возвращены в свои места;
- некоторые детали, которые автор этого видео с легкостью снимает с кофеварки, либо с небольшим усилием устанавливает на место, у меня снимались (устанавливались) ОЧЕНЬ тяжело, поэтому вам могут понадобиться и другие инструменты для этого. Будьте осторожны и постарайтесь ничего не сломать;
- сейчас на Aliexpress продается немного другая модель паровой трубки и использовать уплотняющую ленту не нужно.
Вот думаю на 685 ю поставить. Стоит она того?
@@Петрович0482 стоит, пар стал более управляемым, ну и удобнее взбивать.
@@Bubon-vf9wo спасибо. Вроде ещё говорят, что пенка плотнее. Так?
@@Петрович0482 я бы не сказал, что пена стала плотнее. Но возможно я просто не достаточно хорошо взбиваю
Took me almost 3 hours now still couldn’t get it done lol. Thanks for the video 🙏🏼
Thanks for the video, I'm between different machines and one of them is 35.31, so your video is helpful if you want to change the steam wand.
Attention!
Did you forget to put back the little stopper clip?
My man! Thank you SO MUCH! incredible latte art!!
Thank you, thank you and thank you so much for this video. It took me almost an hour to do this on my ECP3420 but the upgrade was totally worth the time.
Tq bro for your video,just buy the steam wind and so excited to make installation with the same machine like you😍
I did this for my 33.21 machine and I notice 2 things:
1. Noise is very loud in the pitcher while you are steaming the milk.
It makes an unpleasant, loud, screaming sound.
2. My milk doesn't froth as with the old wand. It makes the milk hot but the milk is still very liquid.
Almost no creamy texture. No foam like in the old one.
The old one made different milk structure in the same amount of time.
I tried different positions & angles of the wand but the milk just stays liquid and super hot.
I will try some other milk and some other wand positions, but I am not satisfied after the first run.
Do you have any advice how to make it work properly? Thank you.
Hi ..with this steam tip...I need a bit practice to get a good milk texture... start froth the milk with the tip just at the surface of the milk and try first to get foam..let the tip in the position and no need to drawn in to the milk...just position it until the milk swirling and rotating ...stop after the temperature just too hot to touch ..about 60 degree c
@@Indohomebarista Thank you for your reply. I will try to do it like you said.
One more question: with my Rancilio steam wand I got 2 type of steam wand heads: with 1 hole & with 3 holes.
Did you have the same? If yes, which one would you recommend to use?
Fantastic video! Used it as a distant reference to replace the steam wand on my Delonghi Icona E310. Definitely not something I would recommend, even though I macgyvered the crap out of it.
thank you for the video! really fantastic and wonderful tulip!
The only Rancilio Silva wand I can find is the 6 x 180 not the 6 x 130 you have in your link. Will the 180 be too long?
I don't think so ...
You think a zip tie is enough to secure the tube to the wand ?
Mine model is a little bit different, but the structure are the same. The knot of this model is different than what ur model has. I broke it. It costs $2 for replacement but shipping cost = $8
:P
I used a zip tie!
my machine doesnt produce coffee anymore. i descaled it and even opened it up like your previous video. it drips a lik bit of coffee but drips water everywhere. any idea on what i should do?
I am sorry to hear about your machine ...but you need to identify from which part the water start leaking and try to eliminate it ...it probably because of any loosen connection or leak from the porta filter gasket..I have my other machine have the fitting damage and need to replace it..
Any chance there is an upgrade for the pump? My model seems to be having a hard time lately getting good pressure
Thank you, just needed to know how to take the cover off of the de'longhi ecp3220w
Hi, this is amazing. Do you think the steam wand is compatible with donlim espresso machine?
I'm using ecp3630. What brand of want can i use to exchange it?
I am not sure exactly but the one I use in this video is actually for Rancillio silvia machine..It need some small necessary adjustment
I already installed mine. Have you tried the 3 or 4 hole tips? I can't get the right texture with it. But i can make it with the single hole
Hi..the one I have just one hole tips ..but still ok in my opinion for this small machine
Hi! May I know what coffee grinder machine you are using?
Hi I just use an ordinary espresso grinder ...I use sanremo Treviso LX junior that was already discontinued product I guest.
Selain pakai steamwand rancilio apakah bisa ? Steam wand universal yg lebih terjangkau harganya
Yang penting cocok model nya bro... jadi gak banyak modifikasi pas pasangnya
Hi, quick question, why was the paper tape necessary when reinstalling the tip on the wand? Do we have to do that?
The wand I get is not very well fabricated in my case so it leaks and steam coming out from the thread...
@@Indohomebarista gotcha, thank you
@@Indohomebarista Same with me. I tried without first, thinking maybe it's not necessary, but a lot of steam / water comes out of the threads so a very short piece of narrow plumbing thread tape is a good idea. That can be bought at any hardware store for very little money for a tiny container.
What kind of beans do you enjoy?
Hi I prefer blended robusta and arabica for my espresso drink...the blend ratio can be 50 to 50 or 70 robusta 30 arabica...perfect taste for me...use always fresh bean
@@Indohomebarista Thank you for getting back to me :)
Did you get unpressurised portafilter?
No ..it shipped only with pressurized porta...
Solid work, Adip! Would you say that it is also doable on an eco310?
I am not sure...need to open it to see the line
@@Indohomebarista thank you! I'll take a leap of faith
Kalo boleh tau pke steam wand apa itu bro ? Rencana mau hack juga nih, kalo dibanding sebelumnya hasilnya lumayan drastis ga bro ?
Ini steam punya Rancilio silvia katanya... hasil lebih mudah kontrolnya
Looks great! Do you know if this will work with the delonghi ecam 350.15b?
I am not sure because the wand design can be different.
Will this work for the ECP3630 Model?
Hi. May i know what is the ITEM CODE of the wand did you use as replacement, and what ml/oz of the milk jug you used. Hope you can help me, cause im planning to change my wand using your video. Thank youuu.
That steam wand is actually made for Rancillio silvia in the shop ..you can search for that.. I used 350 ml milk jug..this size is perfect for this machine. :-)
@@Indohomebarista Thank youu. Will try it soon.
Will this work for the ECP 3120 model
I don't think so but it could be similar...
@@Indohomebarista how do I figure out which Racilio wand is compatible
@@gianlucacivichino6104 when I see the type of the machine it looks so similar with the model I have ...I believe for the steam wand model also the same
Ep 3240 I had been open and closes it like 2 / 3 time , while i did not put the horse tight enough, and i twice the steamer and it just split up, i had to open again to check it up , what's going on inside.
1. Be careful with every single pieces, one of my peace fell inside the another side of the water tank , it take me a lot of time to take it out, so if you see some pieces could take apart, take it up and separate it.
2. The click horse it is hard to open it.
3. The cap of the horse it is so hard to twist up, i am a girl i have no much strength.
4. You have to very make sure it is tight enough the horse and the steamer, to avoid do the work again and again .
The click horse is no reusable
Mas ini kalo mau keluarkan air panas nya jadinya gimana mas kalo pas mau buat americano? Rancilio silvia steam tip nya kecil banget mas
Kalau keluarkan air panas di mesin Delonghi ini caranya switch knob di posisi brewing lalu buka steam valve nya....pas baru buka steam wand awas mungkin akan ada steam yang keluar dulu jadi arahkan wand ke wadah lain dulu baru kemudian setelah air panas solid yang keluar arahkan ke cup nya..
Saya biasanya kalau buat americano isi air panas dulu..lalu timpah dengan double espresso mantabs cremanya masih ada di permukaan kopinya..eh itu long black kali ya ...:-D suka kebalik balik
@@Indohomebarista jadi emang air yang keluar kecil yah bang? Kalo udah di ganti bang ateam wand nya
@@DaiLoo888 iya ..karena memang lubang nozle nya satu dan kecil ya..
Is this the same process for other machines from delonghi
I am not really sure but as I know it can be applied for the other model such as ECP 35.31 also
I have a all in one
BCO430 To be exact
Thanks For this but damn it was so hard to remove the pipe and put the plastic thing. Thought it was easy looking you ah ah. Everything work well though, now next step is to reach to froth milk correctly.
Update reach to create foam, there is a world between before and after taste and look absolutely different (not this porous aspect after some moments)
Exactly! Those two were so goddamn hard to do.
Amazing work! Could you please share a link for the steam wand? Have you experienced any issues since the installation?
Hi...unfortunately i bought it in local indonesian market that not ship Worldwide ... so far no issue for me...
@@Indohomebarista I’ve found this one that’s looks like the one you have. Do you know if the one you have fits Rancilio Silvia (V1/V2)?
Rancilio Silvia (V1/V2) Steam Wand www.amazon.co.uk/dp/B00K49GMMW/ref=cm_sw_r_cp_api_glc_fabc_3GHH9K9RXWPN525G99HZ
Yes exactly the same model as I used in my video..if you can get it..I am sure it will be used..
Bang apa semua mesin espresso rumahan si steam wand nya bisa di ganti bang?
Mesin sy ferrati ferro 2009b,bisa ga ya bang?
Malam bang, maaf itu beli steam wand dmn ya? Rekomendasi tokonya dong. Trims
Beli Rancilio Silvia Steam Wand / Gaggia Classic Steam Tube Conversion
tokopedia.link/dYDIkPMxB8 di toko Bangala Coffee Jkt Rp500.000 di Tokopedia dengan Bebas Ongkir, Sekarang!
art looks great!
halo bang, mohon info dong yg punya saya pertama kali pakai handlenya susah banget buat dilurusin? gimana ya bang kalo dipaksa takut patah
Apakah porta dalam kondisi tanpa kopi pas gak bisa di lurusin?..mungkin karet sealnya memang masih tebel original...setelah pemakaian lama kelamaan akan longgar bro..
Yang penting tidak bocor
Would this work on my De'longhi Stilosa EC260BK?
I dont think so..as I know it will work on ecp 35.31 also
Yes, it is the same system
I tried with EC230.BK, it worked well
Excelente aporte funciona perfecto 👌 en Delonghi ECP3420,
halo mas, kalo mesin delonghi ec860m bisa ga ya dimodif steam wand-nya kayak gini? Btw, thanks tutorialnya, super cool :))
Wah belum bisa bayangin bagian dalamnya yg ec860 itu bro.. tapi kalau system nya mirip2 bisa aja sih kalau menurut saya 🙂
Seberapa jauh improvement nya jika dibanding original wand yg rubber? Saya jadi penasaran ingin ganti juga 😬
Lebih terasa leluasa buat kontrol steamnya karena lebih panjang bro..selebihnya sebenarnya gak begitu ada peningkatan lain karena memang power steam nya ya tetep aja
Thank you!
Can u make video how to replace boiler holder?
This music is maddening.
Bonne vidéo du mec le plus lent du monde....lol......Utile néanmoins.
lokasi di daerah mana om.
Ini di Madiun bro...
@@Indohomebarista buka jasa ganti steam wand bang?
@@yudawicaksanaputra maaf nggak bang...
Halo, mas. Mesin yg ecp 35.31 masih dipake tidak ya? Atau sudah ganti mesin ini?
Masih pake Om..
Sudah berapa lama pakai ya pak?
@@louisdaniel1359 sudah 2 tahun lebih ya sampai saat ini..masih perform
Wih mantep, tahan juga ya delonghi, belinya di mana ya pak?
@@louisdaniel1359 saya beli di maharaja kalau gak salah waktu itu..bisa juga di Tokopedia kok
that steamer stopper was a pain to remove. I ended up sawing off the old wand :/
Biayanya berapa mas ? Lokasi dimana ?
Ini cuma beli wand nya itu aja bro di tokopedia..lalu pasang sendiri kok bisa..saya ada di Madiun
They make slip ons instead of taking the machine apart.
Эта музыка сводит с ума
Great tutorial, thanks for sharing
Terimakasih tutorialnya mas. Salam kopi 😀
Thank you so much! It really helped me
Cool work 👍
I have delonghi 35. I wonder it this gonna work with it ?
I am sure that it will work for 35.31 also...it has exactly the same design..
Adip Asmuni thank you for replying 🙏🏼
@Shatha, did you try? Does it work?
@@mi85 Yes it works :)
@@shathakm7079 Is it the same workflow as shown in this video here?
very nice
Mantap
Good job bro
Baik 👍🏼👍🏼👍🏼👍🏼 Terimah kasih 🙏🏼
Good tutorial... But the music ruins it
Link pembelian ?
Search saja gan di toped key "steam wand rancilio silvia"
Маладес! Ощин каласо!
Bro , kalau steam wand nya selain rancilio bisa ga ? ( agak Mahal ) :)
www.tokopedia.com/takgentarsay/high-pressure-semi-automatic-coffee-machine-accessories-steam-pipe?whid=0
ini lebih murah
Link pembelian
Bisa search di toped Bro..steam wand Rancillio silvia
Too stretched video, I was watching on 1.5 speed. Any way, thanks a lot!
Nice video music is horrible and monotonous
Кровь из ушей пошла
Thank you!