Just completed redid my whole front suspension take a day if you have a lift, 2 days on ground if your cleaning & paint everything as you go. 3/4 days if ish go wrong or Strip or break a bolt. Read the directions…. IF THERE IS NO WELDING get everything blasted & powder coated since this your daily driver. If you do powder coating now you can you pick a crazy color or do accent colors
Look into Eastwood extreme chassis black or 2k Ceramic chassis… both come with primer and paints look at the frame in the link it’s Extreme chassis black
You bet I am. Installing the 1.5 lift kit and swapping the front suspension to 4 x 4 will be the same video. I’ll have a follow up/Part 2 video on doing the 4 x 4 transmission, t-care, and driveshaft swap.
You definitely can swap from an automatic to a manual. I’ve never done it before but I’ve read Facebook posts and forum post about guys doing it successfully. It’s made even easier considering a lot of these trucks did come as manual.
So I have most of the front end built. I have a few items for the Dana 44 third member to install and I will release the video detailing the build. Then…I just need warm weather and full day.
Hi Stevie how are you buddy this is Francisco I was wondering if you have a video talking about or how to fix the ignition actuator do you know there’s a gear in there that connects for the cylinder so I’m having problems with that my key is stuck I am not able to release the key
Hi Francisco! If you remove the plastic collar piece around the steering column, you will expose the steel structure that holds the key cylinder into the steering column. There’s a small hole on the underside of the key cylinder. Inside it a pin you can push which will release the key cylinder.
@@TheMinuteMasters Yeah I already released the cylinder I remove the cylinder I pull it out the problem seems to be that is not synchronize the gear and the actuator is not synchronize the problem is not the Sellinger ST actuator I sent you a video showing how to remove the gear I try to figure it out thanks buddy
Hey Stevie I hope you’re doing OK this is Francisco you’re still let you know I sold the truck so my truck is gone I got me a Corolla thanks for everything buddy keep up the good work see ya
I need to know what the dimensions of the fuel pump access door are. From the front of the bed and the side of the bed. I'm going to cut my panels out of a junkyard and the tanks are already removed.
In the original video, I gave you the dimensions. However, every truck is different because this fuel tank can technically be mounted in varying locations. It’s worth measuring under the bed to get your exact dimensions.
Thanks Stevie! I'm 2 weeks away from owning my own '95 f150 4wd. It has dual tanks so I'll have to cut 2 panels. But it does have a rubber mat in the bed so you'll never see them. I've learned a ton from your channel about these trucks. Keep up the good work!
So I never new you were doing a 4x4 swap man i can’t wait to watch this video it will show me everything I need to do mine but I might go with the solo one Motorsport mid kit
I'm a fan of remaining on the terrestrial plane, but you High & Mighty guys, carry on.
Hahaha!
Can’t wait to do this to my bronco. Thanks for the extra motivation!
No problem man!🤙 I can’t wait to install mine!
Picking up a 91 w a 351 in it TM, congrats on the lift can't wait to get to work on this new one. Love the channel. Love the feedback🔥
Nice! That will be cool!
Thanks man!🤙 I appreciate it!
Happy for you man. Hope it turns out great
Thanks man!🤙
Just completed redid my whole front suspension take a day if you have a lift, 2 days on ground if your cleaning & paint everything as you go. 3/4 days if ish go wrong or Strip or break a bolt. Read the directions…. IF THERE IS NO WELDING get everything blasted & powder coated since this your daily driver. If you do powder coating now you can you pick a crazy color or do accent colors
Good to know! Thanks man!🤙
I’ll probably paint all the suspension pieces using a two part system.
@@TheMinuteMasters Be sure to mask off the threads and hind joints
Look into Eastwood extreme chassis black or 2k Ceramic chassis… both come with primer and paints look at the frame in the link it’s Extreme chassis black
@@1DjScarface I have heard of Eastwood extreme chassis black. I might go that route just to keep it easy.
I hope you don't have to deal with inverted front leaf springs. I look forward to your lift.
Nope! Just coil springs for this lift.
excited for this! in the same boat, since I have a 2wd and want to go for DM kit
So DM does make a 2 Wheel Dr. with care, but it’s much more expensive than the 4 x 4 kit.
Marvelous
going to make video how to swap 2wd to 4x4? and will u be doing installation video new 1.5 stage suspension kit?
You bet I am. Installing the 1.5 lift kit and swapping the front suspension to 4 x 4 will be the same video. I’ll have a follow up/Part 2 video on doing the 4 x 4 transmission, t-care, and driveshaft swap.
Nice
Thanks man!🤙
I wonder if i could swap out my 96 f150 form automatic to manual trans? any ideas of how id go about doing that?
You definitely can swap from an automatic to a manual. I’ve never done it before but I’ve read Facebook posts and forum post about guys doing it successfully. It’s made even easier considering a lot of these trucks did come as manual.
When will you be installing?!
So I have most of the front end built. I have a few items for the Dana 44 third member to install and I will release the video detailing the build. Then…I just need warm weather and full day.
Hi Stevie how are you buddy this is Francisco I was wondering if you have a video talking about or how to fix the ignition actuator do you know there’s a gear in there that connects for the cylinder so I’m having problems with that my key is stuck I am not able to release the key
Hi Francisco!
If you remove the plastic collar piece around the steering column, you will expose the steel structure that holds the key cylinder into the steering column. There’s a small hole on the underside of the key cylinder. Inside it a pin you can push which will release the key cylinder.
@@TheMinuteMasters Yeah I already released the cylinder I remove the cylinder I pull it out the problem seems to be that is not synchronize the gear and the actuator is not synchronize the problem is not the Sellinger ST actuator I sent you a video showing how to remove the gear I try to figure it out thanks buddy
Hey Stevie I hope you’re doing OK this is Francisco you’re still let you know I sold the truck so my truck is gone I got me a Corolla thanks for everything buddy keep up the good work see ya
@@FranciscoLopez-cc7ui Hi Francisco! Sorry to hear that but you have to do what you have to do. Corolla’s are good cars.
I need to know what the dimensions of the fuel pump access door are. From the front of the bed and the side of the bed. I'm going to cut my panels out of a junkyard and the tanks are already removed.
In the original video, I gave you the dimensions. However, every truck is different because this fuel tank can technically be mounted in varying locations. It’s worth measuring under the bed to get your exact dimensions.
Thanks Stevie! I'm 2 weeks away from owning my own '95 f150 4wd. It has dual tanks so I'll have to cut 2 panels. But it does have a rubber mat in the bed so you'll never see them. I've learned a ton from your channel about these trucks. Keep up the good work!
@@ChrisStump-w3g Great to hear man!🤙
You have the perfect set up for the hatches.
Thanks!
Is that desolate Motorsport level kit for 4x4 too?
Yup! This is the 4x4 kit.
Awesome can’t wait for the install video 💪
Wrong video
@@Dj-ve2hx What you watched is a trailer for another video. The actual video premieres today at 5 pm.
So I never new you were doing a 4x4 swap man i can’t wait to watch this video it will show me everything I need to do mine but I might go with the solo one Motorsport mid kit
Is this for a 2wd to 4wd conversion?
The kit is for 4x4 and then I bought additional parts to do the swap from 2wd to 4wd.
I will appreciate if you can help me on this one thanks buddy take care
May i know how to work with you about offroad products. And please leave me your email.
Sure! If you have Instagram you can DM me there. My handle is the same as the channel name.
could you send me your email?@@TheMinuteMasters
could you leave your official email? we will send you product list for check@@TheMinuteMasters