How To Fix A Hayward Star Clear Plus Lid

Поділитися
Вставка
  • Опубліковано 29 жов 2024

КОМЕНТАРІ • 21

  • @michaellnbnj
    @michaellnbnj Рік тому +1

    Had the exact same issue. This video helped me immensely! Thank you!

  • @Sojournin
    @Sojournin Рік тому

    Thank you for a nice presentation. A great fix rather than having to buy the entire lid assembly! : )

  • @patrickursomanno8861
    @patrickursomanno8861 2 роки тому +3

    Recently did mine, also sprayed the lid cause the fiberglass was irritating.

  • @anidiaz2139
    @anidiaz2139 Рік тому

    Thank you sooo much! You helped me save a fortune.

    • @Inyopools
      @Inyopools  Рік тому

      That's why we do it! Thank you for the feedback.

  • @John-lm1zg
    @John-lm1zg Рік тому

    Thanks for the great video!

  • @amandagarrison6030
    @amandagarrison6030 Рік тому

    Thanks great video

  • @archerbigdwag
    @archerbigdwag Рік тому

    Does the filter need a rest from running where the pool is still. ?

  • @USTradeNumbers
    @USTradeNumbers Рік тому +1

    Any tips on putting the clip back on at about 4:44?

    • @Inyopools
      @Inyopools  Рік тому +1

      Push it. Push it, real good.

  • @johndale8614
    @johndale8614 5 місяців тому

    My issue is with the bottom portion drain plug internal threads of bottom half are stripped out after 24 years. But NOBODY sells the bottom portion, only the top! lol any fix for this?

    • @Inyopools
      @Inyopools  5 місяців тому

      Are you talking about this part? Star Clear Drain Plug Kit (CX250Z14A) - www.inyopools.com/Products/07501352015726.htm

  • @SoundAloneband
    @SoundAloneband 4 місяці тому +1

    Another thing to check and no one says this or notices. The rod itself the threads over time get this hard green gunk between them and the knob can't grab it properly. Take a flathead or small blade and clean the threads out. This crap will just chip right out. I see this all the time. Been a pool contractor for 16 years now. If the rod is stripped at the bottom end get rid of it. I've seen these blow into the neighbors roof and also take part of a roof off. These have also killed people. So don't chance it.

  • @beautybyhammerllc
    @beautybyhammerllc 2 роки тому +1

    My Dome collapsed . Just another possible issuse . The top gets flat over time

  • @richdettra9567
    @richdettra9567 Рік тому

    My issue is the rod came off and is stuck on the knob so have fish is down very time

    • @Inyopools
      @Inyopools  Рік тому

      Have you tried spraying WD40 on it, letting it soak in, then using pliers and vice grips to get the knob to turn? A WD40 variant called Rust Penetrant can sink in deeper into the threads for better results.

  • @feesor
    @feesor 5 місяців тому

    My problem is not the screw top. It is leaking at the lid with a brand new O-ring and brand new screw top.

  • @steveokeeffe8130
    @steveokeeffe8130 2 роки тому

    MY ROD CAME OFF FROM THE FILTER ,IS THERE A PROCEDURE TO REPLACE AND ARE THEY ALL STANDARD SIZES?