Honda Fourtrax 300 front wheel bearing install

This is a short video of how to replace the front wheel bearings on a 1997 honda fourtrax 300. This is the same process you would use with pretty much any of the older model 4x4 hondas with front drum brakes. TRX300fw, 350, 400, 450, 500, 650, 680 #ad
Link to the Bearings used in the video
ebay.us/DEtlsl
Link to Ball Joint Seperator in the video
ebay.us/FbpCqR

[@bballracer92]

ol 300 feels better now i bet thanks to the doc

[@kennethcoleman2554]

Thanks Four wheeler Doctor.

[@ssur44]

Thanks. This was very helpful.

[@redteam9881]

Getting ready to order bearings and seals for complete 4 wheels 1987 Honda 350D. How many seals does it take ?

[@kerrydeshotels9691]

Do you have a video to just grease the bearings?

[@KennyDuke-l2h]

Whats the torch spec for the axel nut or how should i tighten it

[@berniceperry8898]

Could it have just been loose....NVM I see now...lol....I had one loose onced and I tightened it a half a turn at it was back in good shape....good video bud...

[@FourwheelerDoctor]

Thanks and Thanks for watching.

[@randallclemons8638]

I have a question. I have a 99 TRX 300 2x4. Is there supposed to be a small space between the front axle nut and the bearings, or do I just need to tighten the axle nut down more ?

[@FourwheelerDoctor]

I was thinking that the two-wheel drive model had a spacer between the bearing and the nut. If your spacer is installed yes the nut should be tight to it.

[@randallclemons8638]

@@FourwheelerDoctor there is a spacer in there. Someone had worked on it and didn't tighten the axle nut all the way down. But I was putting a new wheel hub on yesterday and I put the spacer on the rim o had taken off when some people came around, and one of them lost the spacer. I used a bearing brace or race (not sure what it is called) because it was about the same size as the spacer. I would buy new ones, but I can't find them online and I'm not sure what the exact name would be to look for. Thank you for you help. If you by chance know what I should be looking go purchase, please let me know.

[@bruhtommy6814]

What I am wanting to do is just replace the hub ,is that hard to do ?

[@FourwheelerDoctor]

I'm assuming in front. And is it a two-wheel drive model or four wheel drive model?

[@thathonda300kid8]

Do you have a video of a bottom end rebuild on a 300 your mh favorite guy to watch for rebuilds

[@FourwheelerDoctor]

Noni don't right now but I have one coming within the next couple weeks

[@rioncardwell3867]

No grease?

[@redteam9881]

The bearings are pre loaded

[@thomasallred5984]

How do you get the axel nut off without the four wheeler tires spinning?

[@FourwheelerDoctor]

On the 2 wheel drive model, the tire should not turn when loosening the axle nut.

[@thomasallred5984]

@@FourwheelerDoctor I have the 4wd

[@thewhyguy0398]

Where did you buy the bearings at, I’ve been given the wrong set twice

[@justethannnnn8082]

MINSTAR Wheel Bearing Fits For... www.amazon.com/dp/B096W3J3C7?ref=ppx_pop_mob_ap_share

[@justethannnnn8082]

That’s where I got mine

[@FourwheelerDoctor]

Do you have a 2 or 4 wheel drive model?

[@patrickgorman50]

Where did you buy the bearings? Do you have part #? I have the same 4 wheeler 4 wheel drive.