How to Replace Valve Cover Gasket & Spark Plug Tube Seals 1998-2002 Honda Accord
Вставка
- Опубліковано 12 тра 2021
- Buy Now!
New Valve Cover Gasket Set from 1AAuto.com 1aau.to/ia/1AEGS00277
Valve covers will begin to leak oil when the seals eventually break down. A new valve cover gasket set will make sure the oil stays inside the engine where it belongs! This video shows you how to install a new set of valve cover gaskets on your 1998-2002 Honda Accord.
• Check here for more videos on the 1998-2002 Honda Accord: • Honda Accord 6th Gener...
This process should be similar on the following vehicles:
1998 Honda Accord
1999 Honda Accord
2000 Honda Accord
2001 Honda Accord
2002 Honda Accord
Tools you will need:
• Flat Blade Screwdriver 1aau.to/oCJ/1AXAA00013
• Needle nose pliers 1aau.to/oeS/1AXAA00051
• Needle nose pliers 1aau.to/oeS/1AXAA00052
• Pliers
• Torque Wrench 1aau.to/osA/1AXAA00044
• Gloves 1aau.to/oea/1AXSS00048
• Safety Glasses 1aau.to/ocU/1AXAA00343
• Hammer 1aau.to/oim/1AXAA00091
Subscribe: / @trq
Check out our playlist:
Honda Accord 6th Generation 1998-2002: • Honda Accord 6th Gener...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√
At
"carefully drive it in" bang bang bang haha. Thanks for the video, I needed to be sure the aluminum valve cover could take a beating like that.
Beautiful video. One of the coils was drenched in oil. You skipped showing a solution to that in the video. I am in the middle of doing this exact job. I will follow your video when it’s time to put everything back.
It would’ve been nice if you showed the rear valve cover. There’s a wiring harness that makes reinstallation challenging.
THE WHAT?????
Thank you kind sir
How do you remove broken valve cover bolts?
"Give it a few loving bonks"
You’re changing the gaskets and spark plug , just leave the throttle body in and pull the 2 coolant holes instead. Dont you think is easier 😅 otherwise you need to collaborate the throttle again .
I could use some suggestions on how to remove a gasket that wont budge. Its like its frozen in there. I got like an inch of it out in an hour and half. Got tired of messing with it so i stopped for the day.
I could never seem to get the tube seals in right, I’ve tried using grease and something that fits over the seals perfectly but nope. One side always goes in more
never use a metal blade against your machined surface your gasket will meet up to.
What is the torque spec on the bolts ?
Ya took the easy way out. Why didn’t you do back side. It’s much more challenging.
I thought you said should always do them in pairs from the beginning. Now you only did the front gasket, what about the back . Not a complete job 😅😅
And is there one for the 2.3 f23a engine?
6:05
The valve cover bolt stripped on me
People still do t know how to use the internet.