Aqua-Flo Flo-Master XP2 or XP2E Pump Repair The Spa Guy How To Spa Hot Tub
Вставка
- Опубліковано 15 лип 2016
- This video is about The Spa Guy teaching you how to repair an Aqua-Flo Flo-Master XP2 or XP2E Pump and motor... www.HotTubPartsofAmerica.com
- Навчання та стиль
Really appreciate you making these videos, very concise to the point, you don't move to fast, and thorough. Replacing my first wet end shaft and impeller seals, they were bad, and since I had it apart doing both bearings. Everything is apart, waiting for parts to arrive !
If you ordered from us the parts go out everyday if ordered early enough or the next morning except Sunday..
5 star help!!!,watched it 10 times,once at each step,my co-workers think im a hot tub tech,great job!
Spa Guy, you are the man! Hot tube motor locked with hum. Followed your excellent 👍 instructions and for a few bucks for a new seal and impeller, I'm back in business! Would not have attempted if not for your video!
I have been watching all your videos for the past week, man! HUG you are a master and I am more than certain you have saved many a DIY person and educated those that don't know.. Blessings Big hugs and a Million thanks for all your time, knowledge and get it done attitude!! A True Inspiration!
Thanks for watching Scott..
This was very helpful and I thank you for posting it in detail, and saving me $$$! I ordered the parts I needed, followed your instructions...and it worked! Only caveat I had was getting my impeller off - was frozen solid. I ended up drilling the center out of it around the shaft flange with a 1" hole saw, pulled that main part out and then I heated the rest up with a torch until I could pull the rest of it off with a pliers to get at the molded in/embedded nut. Then I cleaned off all the hardened goo with a hammer and chisel, found a socket that matched the nut and my impact gun whipped it right off! Love it when things work as planned! $30 repair vs. $230+ replacement. Installed and working perfect w/ no leaks!
Thanks for watching.. Spa Guy
Thanks so much for the video! You help me determine exactly what pump I had, which isn’t as obvious as one might think looking at the model number. Ordered all the parts from your website and I’m almost done rebuilding two pumps including wet ends and bearings. Even used your tech-support to text back-and-forth to confirm parts and get links for ordering from your site. Couldn’t of done it without you!
Wonderfull I am so glad to help!! Spa Guy
This was a very helpful video. Thank you very much. I will tackle the pump rebuild when the parts arrive.
I really enjoy your videos. I've been a spa repair technician for 16 years. You are a great teacher! Thanks to you, I am always learning a new skill that helps me in my hot tub repairs. (I have never replaced the bearings in a spa motor -until now.)
*As you know, "Salt Systems" are getting more and more popular now... and this is causing shaft seals to leak more often (causing bearings in the pumps to rust due to corrosion).
What you have taught me in this video is an essential skill to know!
You are the best!
Thank You Dwayne.. Feel free to reach out anytime you need help.. Spa Guy
Thank you for this, last time I replaced the motor and pump XP2. Now it's about 5 or 6 years old and something is acting up with it, going to pull it out and look at it. The impeller seems to be connected to the shift ok, and it's not hard to turn. Going to connect it to 110v and see how it does first. Awesome video, looks like I can get parts from you, I definitely will.
Great video, my spa has 3 of these pumps, rebuilt all 3 loud and leaky motors and pumps, I ordered most parts from you and they worked perfectly, got bearings from Napa $6, last time spa repair man just replaced all with brand new units! So I saved $2000 doing this myself, fun project, fun to learn a new skill. Thank you
New to this site. Jets on one side of my spa have little pressure. I think it's the wet end.
Great Video. Very instructive. I am still in the process of doing mine but it would have been impossible with out your help. Thank you very much. Nicely done.
Thanks for watching Guy... Spa Guy
Great video with an good explanation of how to save yourself a couple hundred dollars, by just replacing a leaky wet end on your hot tub pump!
This helped me replace the seal and bearings in my XP2e, thanks!!!
Absolutely Love the video. That's really all I need. I would however like to know where you got the bearing holder.
Thank you for this smart video by a true technician . I replaced the seal and bearings on mine after studying your videos, the oil filter tool is a must. I tried to order my parts from you in compensation but the option to ship to Canada was not there. Thank you once again!
I appreciate the attempt to support.. I do offer items on eBay for Canada but there are too many variables on my site.. My warehouses do not ship out of the country so I cannot logistically sell everything on the site outside of the USA.. www.ebay.com/str/americanspaparts
@@SpaGuy hey bud, I'm another Canadian who wants to say thanks. Can I suggest you add a few nominal things like stickers that we can buy from your international site to say thank you for your video's?
Thanks for this Very Good movie and explanation...Now I can repair my 18years old xp2!!!!! Many thanks
I have a question. I placed a New seal and impeller(old with 2 green dots) I checken before the motor and it is running. When a placed everything together the motor won't running. When I remove the New empeller the motor is running again. What is my fould or mistake in this all?
My father and I are putting together a hot tub and we found the answer we were looking for with yer video
Great video. Have the same problem with my pump. But, think I'll just buy a new pump.
Great video, very informative and to the point.
Thanks spa Guy you are the best, question 2002 master hot tub model STS the temperature only rises when it is at high speed, if i don’t use the hot tub the temperature goes down . Thanks
Excellent video ! Thank you
Great, detailed video!
I have the same pump and in my case it has difficulties to start. I have to use a flat crew driver to kick-start it and then it runs fine.
Could you tell me the capacitor on top of that pump is Run or Start capacitor? If it is a Run capacitor, where is the Start one? I did not see it when you took off the back cover.
Thank you
Thanks so much for such a great video! It helped me fix my own Aqua-Flo XP3 after the impeller disintegrated; saved me hundreds of dollars! Luckily the bearings were still good. I just took apart the volute and put in the new impeller, following your example.
(Does anyone know the answer to this: Will the impeller normally last "forever", and having one disintegrate means there's something else wrong with the hot tub? I can't imagine how or why it happened. The seal was fine, the wear ring was fine, everything looked normal. Well, except for the impeller in pieces...)
Great video, thank you. I rebuilt my XP2E in my Softub with your advise. Reassembled, reattached, refilled, fired up and it ran awesome for 30 seconds then the whole thing shut down. It just clicks instead of firing back up. Took it apart again, it spins fine by hand. See no probs. Pulled control panel and there are no melted wires or obvious problems. It will not start. WHAT HAPPENED!?
Thanks for your videos ! I have the same pump and I believe we have a bad capacitor, does this specific pump has two capacitors? Seem like my start capacitor is bad (is that one inside the motor?)
Great Video. Well explained.
I have an interesting phenomenon going on. I changed all the wet end parts on only one of my pumps. That pump now jerks when going from high speed to low speed, while the pump with original parts transitions from high to low speed very smoothly… I can’t figure it out. Any one have any clue?
Great video. Wish you had a more difficult time removing the impeller. Mine is on there solid. I'm going to have to take a damn grinding wheel to it.
Good job.
Hi spa guy great video. I have a question. I recently bought a house that has hot tub. It has the 56” 2in 2 out. However the wet end looks like it has been replaced in the past. The wetend says 1.5hp (sticker on it). I notice the jets are very weak. Do you think the wetend is not pushing the water enough?
Great information !
I have leaking coming from where the face meets the housing of my XP2E from freeze damage. No cracks. How would you repair that? New oring and silicone? Replace housing and face? Thanks love your videos 👍
Very thorough
I have an Aqua-Flo XP2 Emerson motor. I believe it’s a 56 frame but I’m not sure. I’m trying to replace a bunch of parts on the wet end as well as the bearings. I’m can’t figure out weather I need XP2e parts for wet end or just XP2 and if I have a 48 or 56 frame. I measured one thru bolt to the other and it was very close to 4”. Help please.
Hey, Spa Guy. I have an older tub with 2 XP2 pumps. There is a hose running from one wet end to the other. Any idea what that’s all about? I haven’t seen any wet ends replacements with a place to connect the hose.
Regarding the XP2e question, I bought the whole assembly (motor+ wet end) due to wet end leakage, and motor bearings worn out. I'm worried the control electronics won't be able to handle the more powerful motor (higher amperage rating).
great job!
What are the 2 ports for that look similar to the drain port? Mine are leaking, do I need a new wet end?
Do you know what swim pump they use for the swim jets? for hydropool and swimlife. Need some help. Aqua-Flo Pump XP2e 5HP is this power enough for a good swimmer
Thank you Spa Guy, just what I needed.
Hello Spa guy, nice video! But i have a question...i have the xp2e europeon version, during construction works in the neighbourhood, my capacitor melted...you can not read anything on it (anymore..?), so now i don't know what kind of capacitor i have to order. I think the pump is the 2hp version (not on the label, only that it is a 1.5 kw), the other capacitor (16uf 450V) seems to be ok, but it is the biggest of the two that blew away....can you help me with this? I can not find anything about it on the internet....
Thank You for watching.. Spa Guy
Excellent Video and answered all my questions about repairing the XP-2 ....... BUT ONE ! Is the Silicone you refer to actual Grease or the GE/Dow Silicone Sealer?? I had to cleanup the Motor shaft as you described, but the bearings were like new. The Ceramic bearing had jammed into the Impeller sleeve and sheared it off, so I needed a new impeller as well. One of the eight screws holding the wet-end cover was rusted shut and snapped off. I drilled out the flange to accept a small #6 nut and used JB Weld to seat it. Thanks for the time and effort.
When you buy your parts from me which is the purpose of the video you get silicon sealer..
Great videos, thanks for the help. I managed to break one fin completely out of my motor fan. Are there replacement fans available?
In most cases no internal parts are available except a bearing...
Thank you! Sir
Where is the repair kit located that you're talking about in this video? Husband is wanting to order it.
I've got dual XP2e's and got the FLO error. Found one of the fuses blown, replaced and tub ran for one use and fuse blown again. Guessing this would be bad pump bearings drawing too much load. Pulled everything apart checking for blockages but nothing
I have this model of pump, but my capacitor is bad. I can't read the label to determine the make and raring for it. Do you have information on the type of capacitor this pumps uses?
Awesome video. Learned an awful lot! Thank you for that!
I've got a problem, though that maybe you can help with. I have an XP2. When I flip the breaker on, if I do nothing, the motor will hum without turning for a few seconds and then the tub errors out (three dots). However, if I give the drive shaft a nudge with a screw driver or something, it spins up no problem. But every time the tub shuts down, when it tries to kick back on, it hums and three dots out. So I'd have to manually nudge the shaft every time. Once I give it that nudge to get it running I can switch between run and circulation modes no problem.... while heating. Once it is at temp, if I hit the pump button to turn switch out of run mode, it just shuts off.
I've tried replacing the start capacitor and that didn't work. I've manually spun the shaft (with the power off) and I don't feel any grinding or resistance at all..... any ideas?
I have a problem... The breaker keeps tripping AND and the fuse blows on my down east spa hot tub. I replaced the heating element and it did it again. Can’t be ozone, it’s been disconnected for a while. The hot tub has an LED bulb that is going out.. maybe that. If it’s not the LED, I’m left with the motors. Tomorrow I will take the bulb out and replace the fuses and try again.
Just wondering if you’ve come across this before?
Nice Video! Where did you get three piece part that you used to remove the bearing? Not the puller, but the part that attached to the bearing. Thanks
Hello, That is a Bearing Puller Cage designed for that bearing.. They are expensive about 200.00... I wouldn't invest in one unless you were doing a lot of pumps.. A regular 2 or 3 finger pulley puller will work just fine normally.. Thanks, Spa Guy
Just FYI you use a rag or rubber wedge to remove the impeller. Do not use oil filter pliers or pliers to remove the impeller unless you are willing to break / damage it. It's just plastic. Rubber wedge is probably the best. Folded up rag wedged in 2nd. It may take several attempts with the rag solution if it's your first time till you figure it out.
Back cover won’t come off. I mean, i got it loose, but there’s something holding it to where it won’t come off. I have some clips on the air inlet but am afraid to remove it (it’s springy and will go inside). Time to take it to the oil store
Excellent video. I have an aqua-flo flo-master xp2, 4 hp pump: model number : 066 20390-2; code 04260;serial number083461-239. It is arcing behind where the cord is hooked into the motor and tripping the GFI circuit breaker. Your video indicates that the two speed switch is hidden behind there at the 7 minute time on the video. Is it possible I just need a new two speed switch? If so, do you sell them? I will pull the pump out in the next day or two to see if the motor is locked up. The windings are not shorted to the frame. It is an Emerson circ pump motor, model number T55CXBMM-986; CAT 7700; SF 1.0
I am an experienced appliance repairman.
Your video was very helpful. I commented on another video you posted before seeing this one. I have a aquaflo XP2 4hp spa pump ( approximately 11 years old). I replaced the 2 bearings on my pump but in doing so I damaged the switch on the rear end. Do you have a video on replacing that spring loaded switch? I re-installed the pump and it would not work. Any help would be greatly appreciated.
I have never damaged that switch before and it may not be available.. I need to know the brand of the motor and if it is a 48 or 56 fr and the amperage.. Spa Guy
Do you have an email address where I can send you a picture? My pump is a Auqaflo Flowmaster xp2 4hp Model # 07340453-2 code 04015. Amp-16.4/4.8 fr 56y class f Phase 1. If this switch is not available do you have any ideas how I could repair the existing one? Also I have changed every part on pump in the last 2 years except for the capacitor. I hooked up the motor and plugged it in and all it does is hum ( after I changed both bearings and broke the switch). The reason I started all this was to change a bearing at the wet end and I decided to change the rear. That being said...I have to ask myself why the bearing failed after I changed it 2 years ago. Was it the capacitor? Thanks for all your help
Yes email is parts@htpofa.com
I have this same pump and wet-end. The pump still works and pushes water but recently has began to have a very high pitched sound/whine. It looks as it is not leaking so do you think this is coming from the pump or from the wet end?
Charlie, It is probably the bearing because there is really nothing in the wet end that would make that mind of nose unless something is stuck in there.. an Old mechanics trick is use a broom stick or other piece of wood put it up to your ear and then on the motor and pump and the sounds will resonate through the wood so you can pinpoint the source of the noise... Thanks for Watching.. Spa Guy
Thank you for the video. We replaced the capacitor, the pump is still getting hot and will only randomly come on. We have XP2 5.0HP. At this point I'm wondering if we should just buy a new pump. I didn't see a 5.0HP in you online store. Any suggestions?
There is no such thing as a 5hp XP2 that is why you are not finding it.. What is your amperage and Frame size? hottubpartsofamerica.com/pumps-and-related-parts/jet-pumps-complete/aqua-flo-complete-pumps/
My Flo Master (1 1/2 hp) has a 3/4 inch tube connected to the front of the wet end . What is this for? I'm replacing the whole pump and I guess I should reconnect the 3/4 inch tube (on barbed fitting with clamp) to the wet end of the new pump? Thanks!
I have never seen a 3/4" tubing connected to a pump.. Some old Leisure Bay tubs have a 1" line threaded in the front right above the suction.. I just cap those off..
Great video! You really simplify everything. Question for you...i have an older XP2 pump 230Vthat has a bad wet end and a new XP2 pump 115V. Any reason why i couldn't transfer the new wet end to the old pump as long as it fits? My tub requires a 230V motor so i cant just use the 115V pump by itself.
It depends on the Amperage rating of each motor and the pumps that are on them.. The 115V only goes up to a 2hp and the 230v could be 1-4hp..
Spa Guy thanks for the quick reply! Both are 2hp 2 speed. Old pump 16/8 amps and new is 13/4.
13 amps on 230 is 3.5HP not 2hp
Spa Guy Forgive me for not quite understanding your reply. The old pump motor is 16/8 amps which would be used with the new wet end. The new pump has 13/4 amps. Are you saying it will not work?
@@mackyt16 I have no idea how you can't understand they are 2 completely different horse powers so not it will not work.. It will probably bolt on and move water but the power differences will create other issues..
Hello, I purchased your rebuild kit for the XP2, 1 HP. 110V, 2 speed pump, 12A. Front bearing was bad and impeller shot. After rebuild when I plug in the pump it goes automatically and directly to high speed and stays on high speed even though I can hear relays clicking when I push the button. I can't turn the motor off unless I unplug the hot tub. I also get a code "IC" and not sure what that means. On the Balboa circuit board I plugged the white wire to neutral, black to hot black while the green to ground. The red is open since I am not running 240V. Did I possibly screw up the switch on the rear of the motor shaft? When I put it back together everything seemed to go smoothly. When the hot tub is operating properly it is suppose to go into prime mode first for five minutes and then the pump will turn on to low speed but again It automatically goes to high speed without the prime mode. I also appreciate the rebuild kit at an affordable price and the shipping was super fast.Thanks.
The "IC" error is reporting: "Ice” Potential freeze condition detected since newly added water temp is 45 degrees.
No action required. All equipment will automatically activate
regardless of spa status. The equipment stays on 4 minutes after
the sensors detect that the spa temperature has risen to
45°F/7.2°C or higher.
I am going to run the hot tub and heat the water enough to get beyond the 45 degree range and see if my pump has it normal functions again.
Sorry for the hassle but I figured out the problem. The motors 4 pin connector was plugged into port J50 when it should of been plugged into J23. I didn't know I had additional plug in options. Me Bad!
My seal kit say to NOT use silicone to install but to use a lubricant compatible with seal elastomers. Also make sure you don't get fingerprints on the polished faces of the new seal.
If you were paying attention I don't use the silicon to lube it I use it to seal the seal to the impeller and Volute.. I have never and will never in any video say to use a lubricant on the seal surface..
@@SpaGuy you keep saying silicon or your special silicone to seal the seals and o ring. My bearings I ordered are U.S. SEAL MFG.bearings and come with a warning not to use silicon based sealant or PTFE sealant. They recommend only using U.S. SEALUBE . I ordered a small amount from Amazon.
Anyone help: I have a problem...I replaced a seal and impeller also the Capacitor for start and running. It is een flomasterxp2. Now the xp2 won't run. When I turn it thexp2 start running. Where and What is Now the problem?
I grind the bearing off sometimes
Hey Spa Guy! I have an xpe2 pump. Thinking about just buying a new one - it’s really messed up. It’s a model 05725015-5 but I can’t figure out which HP model it is. It’s blank on the label. Any ideas? It’s definitely a 2” intake and output.
This video will tell you how to figure out HP and more or just read the disruption on any of the XP2 wet ends.. ua-cam.com/video/JE-CcWqTHQg/v-deo.html
Hi spa guy hope you can help,I have a catalina 200 spa with Ive just got,its been running for a week with on problem but today a FLO code came on for a second and then off when I put the first jet on, you got any tips
cheers DEK
Hello Dek Till, You need to watch the pressure switch How To Video so you can understand how to switch works... It most likely is a pump issue though and you don;t have an Aqua-flo in a Catalina you have 2 1/2" x 2" Waterway pump... If the system tells pump one to come on and it does not you will get a Flo code... It is possible that when you touched the button it was trying to start in low speed and not starting you touched the button and it went to high speed closing the switch and turning the code off... If the pump has been worked on you could have a bent switch in the back of the motor if not you could have a bad starter cap or the switch or motor is going bad or is bad... Spa Guy
Spa Guy hi thanks for taking the time to reply
When I press the jet button it starts ok in very low speed as it should after about 10 seconds it shows the code for 2 seconds but still works fine the only think that has changed is
I've put a new nature 2 mineral stick in the holder dose it just need to recalibrate
Cheers DEK
I have a Problem with a pump that I just rebuild that has a waterway wet end and when I put the cover on the Pump it won't rotate would you know what the cause is
Hello Stephan, It is possible that you chose a 4 or 5 hp impeller and had a 1,2 or 3 hp impeller in the wet end before.. The Wear ring for the 1,2,or 3 is thicker than the 4 and 5 wear ring.. Look at your old impeller just a little off of center and it will usually have the HP stamped in the impeller.. If you have a 1,2,or3 and you purchased a new 4 or 5 then that is why.. You can cut the end off the wear ring and make it shorter so it will fit.. Let me know what happens.. Thanks for watching, Spa Guy
+Spa Guy no I confirmed with the parts guy that it is the right impeller it it was a 1 1/2 and the part numbers on the old match with the new one and there was no wear plate on it
Hi it is silicone as glue or silicone as slihgt (as wd40?) Thanks so much
Sealer
Looks like someone put a screwdriver in the vent holes that are around the hosing to try and hold or stop the shaft from spinning so they can get the impeller off!.. 😂😂
Not in this video..
Did anybody ever find a few small ball bearings in their hot tub water? Coincidentally my pump shut down a few days later.pls advise
Bearings are probably from the rotating jets. Check if any dynamic jets seem stiff in rotation.
What type of silicone are you using please?
hottubpartsofamerica.com/search.php?search_query=silly+juice§ion=product
Want to replace Pump. Motor is Magna Flow MM23032-4, What "wet unit" do I need?
If the old motor breaks I hope be able to purchase just a new motor not both motor and pump.
I hope to use the wet unit I buy to fit the 48 or 56. How do I buy a "CNP wet unit. I have everything apart much thank to your movie.
hottubpartsofamerica.com/universal-cmp-spa-hot-tub-pump-wet-end-2-x-2-48-or-56-frame-3-hp-barb-video-how-to/
Here is the link but the motor it would work on would have to be 12 amps on high speed... Spa Guy
hello, would you be so kind as to tell me the rough dimensions of the bearing? somehow I can't find it here. probably also due to weak English. Thank you very much and greetings from the Czech Republic.
hottubpartsofamericaglobal.com/motor-bearing-deluxe-high-quality-6203-fits-most-but-not-all-motors/
That is the correct bearing.. Thanks, Spa Guy
@@SpaGuy thanks
Hi. If i pulled the entire stater out without the hash marks, how do I put it back together without the marks?
You just put put back in.. I mark it for balance and such if you didn't there is nothing do do but put it back to together..
Thank you for getting back to me so quickly!!
The part that comes out is the ROTOR, the part that is stationary is the STATOR
Not on my videos.. And the name of those two parts make zero difference in the outcome of the repair.. We could call one the tater and the other the spud.. No difference.. Thanks..
The rotor rotates and the stator is stationary ....great video...thanks
What causes the wear ring to wear un even?
They just wear if it is worn just replace it..
thank you@@SpaGuy
where’s the best place to buy a new motor?
www.hottubpartsofamerica.com
Thank You
My original XP2 pump shows the horsepower rating as " 4 SPL, and an aperage rating of 8.6/2.8 amps (48 frame). The XP2e
replacement I received shows the horsepower rating as 5 ("4 OPHP"), and amperage rating of 15/4.8 amps. Can the XP2e (56 frame) be used as a replacement for the XP2, and would it be compatible with the existing electronics?
Hello John, If your motor is a 48fr 8.6 Amps High Speed it is in fact a 1HP pump no matter what the HP sticker Says also a XP2 wet end is not a 56fr wet end an XP2e can be either though. If you got a Xp2e Impeller for a 15.0 amp High Speed motor it is not correct as the XP2 and the Xp2e are two different Size bodies as well as the impeller would be much larger...In fact there are even two different size xp2e's one that is 6.1" and one the is 6'3". Not to even mention he Xp2e is usually found on a 56fr motor and it cannot be used in place of a XP2 used on 48fr motors.. They are two very different wet ends even thought they look similar. If you put a 15Amp impeller on a 8 amp motor it would destroy it in short order by overheating and overworking it. The things you must line up on an Aqua-Flo wet end end to get the correct inside parts ar ,is it an xp2, or xp2e 6.1 or xp2 6.3 version then what is the amperage. Then there are even different wear rings for the xps, as opposed to the xp2e and then to really confuse things the xp2e 3HP wear ring is different than all of the others.. At least the seals are the same... If you go to the Aqua-Flo Section of my site i try to unravel some of that for you.. Thanks, Spa Guy www.hottubpartsofamerica.com
Where do you order parts from?
www.hottubpartsofamerica.com
Why didn’t you clean the rust off the stator before you put it back? I have more rust on mine than yours, but it did work before I took it apart.
I just do.. Probably doesn't matter but I do it..
It didn’t look like you cleaned it. Not the shaft, the armature. If you did clean it, what did you use?
Oh I misunderstood the question.. No reason to clean the rotor.. The rust makes no difference..
At 9:15 you remove the plate and I cannot get it off. Everything was smooth until now.
It does spin freely so not even sure I need it off..
Why can I buy that puller ?
Where
Where could a guy buy that puller ?
If you are talking about the bearing puller you can fine something close at the autoparts store..
Can I order the seal from you?
hottubpartsofamerica.com
@@SpaGuy Thanks
Spa Guy...My flo master started getting loud, sounded like a bearing but I don't know for sure. I'm watching but thought I'd reach out. For now, I drained the hot tub because I don't want to pay the local repair guy $700
Are you still replying to people i gotta crazy issue i cant figure out?
You are awesome man thanks. I just no lie rebuilt (took apart cleaned and replaced bearings) on 2 of these i found in a buddies junk pile, still attached to the hot tub. 1 wouldn't turn at all and the other barely turned. i stopped your video at the right times and followed along. both work perfectly now. not even kidding thank you. but i have a question. the motors have a high and low speed. black and red, and a white neutral and a green ground. the lable on the motor says 230v but if i try to hook a hot to the red and a hot to the black and neutral to white, it trips the breaker. but when hooked up as 120v and using red and black depending on speed then it works perfectly. what am i missing? and how is that 230v?
thanks again and you're help is greatly appreciated.
Common White is Hot on a 230V Pump then Low is usually Black and High is usually Red.. So Black and White 230V is Low Speed and Red and White 230V is High Speed..
Love. 📝📆❗🔺🔻🔤🔎💝
Hi Spa guy I need to repair a wet head
Ok Go ahead!!
HAVING TROUBLE FINDING THE PART NUMBERS AND PARTS FOR MY AQUA FLO FLO MASTER
MODEL C5834005-2, CODE 09308, SERIAL #226692-002Y, 130V, 1PH, 2HP, 2SPEED, CAP START, 56FRM.
I CAN FIND THE PARTS FOR THE WET END, BUT NOT THE MOTOR. HAS A LABEL FOR MARATHON, BUT MOST OF IT IS FADED AWAY, SO I HAVE NO MODEL NUMBERS FOR THE MOTOR. ALSO MY FRONT PLATE IS SEIZED TO THE BEARING AND I AM HAVING A HARD TIME GETTING IT OFF. ANY HELP WOULD BE APPRECIATED.
I have an Aqua-Flo XP2 Emerson motor. I believe it’s a 56 frame but I’m not sure. I’m trying to replace a bunch of parts on the wet end as well as the bearings. I’m can’t figure out weather I need XP2e parts for wet end or just XP2 and if I have a 48 or 56 frame. I measured one thru bolt to the other and it was very close to 4”. Help please.
I have a flo-master pump model #06625001-2 this will do 1 click when you try to turn it on and then nothing else. Our spa was accidentally drained and the pump was run with no water. What do you suggest? total pump shot? what should we begin to trouble shoot> It is on a Vs7 Atera spa
Hello I don't understand what you mean by 1 click... Are you saying it only has one speed or it tries to start then clicks and does nothing? Spa Guy