En mi caso resulto ser el enchufe del sensor de temperatura, no hacian contacto todos los cables, asi que torci un poco los pines del sensor de temperatura y quedo funcionando bien, tuve muchos problemas, habia cambiado practicamente todo
Very good video! How do you set the dash to test mode? I just see you turning on a external power supply and the dash is in test mode. Is there a separat pin on the dash connectors to supply with 12VDC for test mode?
Is it a possibility if I take my cluster out, to repair both the temp and fuel gauges that my key won’t work to turn my car back on? I had a 2008 Audi A3 which I needed to replace a ignition switch and barrel, once i did I had triggered immobilizer and my car never turned on again without needing the dealer to re program my key. So I’m afraid of repairing these little motors and my 2004 3.2 v6 TT not turning on again without having the dealership program my key.
Hello there great video I must say. Slight problem I have is when I bought the car my traction control light wouldn't come on. I've done a search with VAGCOM and no issues. Tried a different speedo and light comes on. My question is how do i get to the bulb or display to see if it's been covered in the past?
@akspeedo how can i order the temp and fuel motors for audi tt 1999 i've been to your website but i don't know witch one should i ad to card 🙏🙏 thank you for the vidéo ✌
Hi! Thanks for the video! I replaced the fuel gauge motor and put the needle to "full" (while ignition is on) since the tank of my car is currently full . When I switch the ignition off, the needle does not go back to "empty" but stays somewhere just below "half". When I switch the ignition on again, the needle goes to "full" again. Do you have an idea what the problem could be?
Are still repairing insturment clusters? If you are, can you repair a cluster off a BMW motorcycle 2005. R1200GS. The speedometer & tachometer are not working. Thanks. Robert
My temp needle jumps around, a cold car will start at 90 degrees then while idling the needle goes to 130 and then while driving it will suddenly drop to 50 hitting the dash sometimes puts the needle close to 90 . Temp in the AC screen (code 49) corresponds with the needle, when temp gauge is "overheating" AC temp reading says 122 degrees, when temp needle is at 50 AC reading says -10. Is this the pointer motor thats faulty or?
i have 2000 audi tt that fuel gauge doesnt work. i used my scanner to read fault codes in the DashBoard and it gave me a code 00771 fuel level sensor (G) short circuit to earth. does that mean the fuel gauge motor is bad? do you think changing the little motor of the fuel gauge is the fix for the short to earth.? thanks a lot for your videos.
The the motors have a creeping short to the ground/earth, which causes them to read high is the underlying issue...so yes. You need to change the motors. Magneti Marelli has a lot to answer for as a lot of components in the Audis of that era suffer from such stupid problems and almost always, at the heart of it, is some little thingamabob from Magneti Marelli.
@@thomasroberts7349 Hi Thomas, thanks for your input, normally a pointer motor fault, but as you've said, the sender unit in the tank can be faulty, but not a common problem, thanks
@@akspeedo how can i order the temp and fuel motors for audi tt 1999 i've been to your website but i don't know witch one should i ad to card 🙏🙏 thank you for the vidéo ✌
0:40 and 8:05 looks very much like the fuel and temp needle illumination is out as well? You really should have reflowed the resistor on the other side of the board (immediately above and top centre of the LCD glass) while you were in there.
Thanks for video and spare part supply. My 2001 A3 8L fuel gauge is working well again.
A really easy to follow repair video, thank you for taking the trouble.
No problem, cheers www.akspeedo.com/
ive had trouble with my temp gauge,you have cleared this up for me brill video excellent instructions ill be ordering a s a p mant many thanks
No problem, cheers www.akspeedo.com/
En mi caso resulto ser el enchufe del sensor de temperatura, no hacian contacto todos los cables, asi que torci un poco los pines del sensor de temperatura y quedo funcionando bien, tuve muchos problemas, habia cambiado practicamente todo
Hola. Donde esra ese sensor?
Very good video! How do you set the dash to test mode? I just see you turning on a external power supply and the dash is in test mode. Is there a separat pin on the dash connectors to supply with 12VDC for test mode?
Hi I have a Audi TT mk2 8j haven a issue with temp readings it’s not moving
@akspeedo I replaced my dash and now it reads reversed do you know how I can fix this?
Is it a possibility if I take my cluster out, to repair both the temp and fuel gauges that my key won’t work to turn my car back on? I had a 2008 Audi A3 which I needed to replace a ignition switch and barrel, once i did I had triggered immobilizer and my car never turned on again without needing the dealer to re program my key. So I’m afraid of repairing these little motors and my 2004 3.2 v6 TT not turning on again without having the dealership program my key.
Hello there great video I must say. Slight problem I have is when I bought the car my traction control light wouldn't come on. I've done a search with VAGCOM and no issues. Tried a different speedo and light comes on. My question is how do i get to the bulb or display to see if it's been covered in the past?
@akspeedo how can i order the temp and fuel motors for audi tt 1999 i've been to your website but i don't know witch one should i ad to card 🙏🙏 thank you for the vidéo ✌
Hi, please email: akspeedo@hotmail.co.uk
Hi! Thanks for the video! I replaced the fuel gauge motor and put the needle to "full" (while ignition is on) since the tank of my car is currently full . When I switch the ignition off, the needle does not go back to "empty" but stays somewhere just below "half". When I switch the ignition on again, the needle goes to "full" again. Do you have an idea what the problem could be?
And another question: the needle of my temperature gauge is slightly tremblig after reassembling the speedometer. What could be the reason?
Did you replace the metal coil cover?
Are still repairing insturment clusters? If you are, can you repair a cluster off a BMW motorcycle 2005. R1200GS. The speedometer & tachometer are not working. Thanks. Robert
Hi, drop us an email: akspeedo@hotmail.co.uk
My temp needle jumps around, a cold car will start at 90 degrees then while idling the needle goes to 130 and then while driving it will suddenly drop to 50 hitting the dash sometimes puts the needle close to 90 .
Temp in the AC screen (code 49) corresponds with the needle, when temp gauge is "overheating" AC temp reading says 122 degrees, when temp needle is at 50 AC reading says -10.
Is this the pointer motor thats faulty or?
Hi, if the temp reading is incorrect on the ACC, I'd check the and replace the sensor first, cheers
You opened it up, why not replace the FIS LCD?
Yes, been done, checkout the video link below:
ua-cam.com/video/OW28wMbjv90/v-deo.html
Thanks
i have 2000 audi tt that fuel gauge doesnt work. i used my scanner to read fault codes in the DashBoard and it gave me a code
00771 fuel level sensor (G) short circuit to earth. does that mean the fuel gauge motor is bad? do you think changing the little motor of the fuel gauge is the fix for the short to earth.?
thanks a lot for your videos.
Dam people put up videos and they never get back to help with questions im going through the same thing as you
If you never got a reply yes. You need to change the little mothers out.
The the motors have a creeping short to the ground/earth, which causes them to read high is the underlying issue...so yes. You need to change the motors.
Magneti Marelli has a lot to answer for as a lot of components in the Audis of that era suffer from such stupid problems and almost always, at the heart of it, is some little thingamabob from Magneti Marelli.
No its not the gauge motor. Its the sending unit in the tank that is bad. Common problem. Drop the tank and replace the sending unit.
@@thomasroberts7349 Hi Thomas, thanks for your input, normally a pointer motor fault, but as you've said, the sender unit in the tank can be faulty, but not a common problem, thanks
Why not use VCDS and set the tank sensor higher like on 135. A lot easier
Not everybody has VCDS, James
Why was it still flashing up coolant level low on the centre screen
Hi, this is because the speedometer is not connected to the car.
Cheers
Oh right cheers 👍
How i can order these 2 pointer motors? Do you have any link?
Hi, yes available on our website www.akspeedo.com/
@@akspeedo how can i order the temp and fuel motors for audi tt 1999 i've been to your website but i don't know witch one should i ad to card 🙏🙏 thank you for the vidéo ✌
0:40 and 8:05 looks very much like the fuel and temp needle illumination is out as well? You really should have reflowed the resistor on the other side of the board (immediately above and top centre of the LCD glass) while you were in there.
Yes, noticed this later, was fixed before we handed the speedometer back to the customer, thanks for your input