Thank you for this easy to follow instructional video on how to test/check a refrigerator compressor. You helped me to understand how to see if a compressor is still good or needs to be replaced. Thank you again and keep up the great content.
Thank you so much for sharing this information you've taught me something about the compressor on the mini fridge I just got from a friend. They said it wasn't working and that they have fixed it. However at 5 it's not getting cold enough and the refrigerator seems to be getting hot so I thought to take a look at the compressor and look on UA-cam to see what was said about this refrigerator. The compressor has the three pins on the side not on the top it is protected by a box. It looks as though the wires have been chewed by something and it looks like I will soon be rewiring this compressor when I have the money. Hopefully this fixes my problem and I don't have to replace the whole compressor. For now working it just doesn't get very cold. At least I know it's a problem in the wiring back here. I wish I could take a picture to show you or send you some video.😂 I am worried because this compressor is very hot and so was the sides of the fridge. It looks like I'll be doing some work on this one. Thank you so much for being there.
Good morning Thank you in advance for the video. Individual things are explained nicely. Unfortunately, I can't understand some of it. Can I ask for an explanation (description from 4 minutes 19 seconds) of the entry on the left: C=R+S, R=Medium, S=Low. What measured values does this apply to (resistance, voltage). The description on the right side C+S=15.3 Ohm, C+R=16 Ohm, S+R=32 Ohm is super explained and clear. I just can't understand the description on the left. Regards
After connecting any refrigerator compressor before switching on Use a clamp on (amp) meter To check the start The amp reading will be higher To check the run The amp reading will be less then starting
The freezer compartment works fine, but the fridge compartment does not cool at all. So I tested the compressor in accordance with your informative guide. M-->C=17 S--->C=30 S--->M=48 I guess this means it's time to stick a pipe through the top and use the fridge as a wardrobe.
@@forevertechenglish There are no markings to identify the three prongs on my compressor, but the relay that plugs into the compressor is marked C, S, & M at the corresponding points. I'm assuming M is the same as R. If I were to rewrite this using your terminology: C + S= 30 ohms C + R =17 ohms S + R = 48 ohms Between C + S and C + R is a 13 ohm difference. That's bad, right?
When the FREEZER {compartment} is working as it should T%he compressor is functioning normally Some Eastern EU refrigerators were more advanced than those in the Greedy CORPORATE West - and were built with two compressors - one for the FREEZER - and one for the REFRIGERATOR section. I had one decades ago - and it was built in Yugoslavia - when the USSR existed That refrigerator.Freezer was designed and built to last - unlike appliances and devices today - built to last 4 years max --- And manufacturers only keep replacement parts for 5 years --- then they dump them - SO the consumer is unable to buy replacement parts - and is FORCED to spend their income on expensive NEW Junk. That is economic slavery.
I’ve been doing refrigeration repairs for 47 years and I never heard of a weak winding. There either open winding. Shorted winding.( internally. ). or shorted to ground. and I call that a multimeter.
The weak winding means that the compressor starts fine and runs fine at the start, but 10-15 minutes later, the compressor heats up more than usual; sometimes, there can be electrical causes the compressor to heat up, but if the electricity is ok, the compressor still becomes so hot that it even trips the protecting thermostat, which stops the compressor. In the area where I am working, the people do not believe you when the compressor starts well and works for a few minutes. At that moment, we used the word "weak" to make them understand that the compressor is faulty.
Awesome educational video. Thank you for sharing. I had a Magic Chef (no short to ground, in ohms) with C & S = 12.1, C & R = 10.2, S & R = 17.4. What might have happened to S & R? Also, I believe you mentioned that adding a capacitor to the start or run winding if anyone of them happened to get weak. Do you have another video showing how to determine the proper uf to add and the wiring connection? Regards.
The windings of the compressor on my Whirlpool Fridge (1999 model) are as follows: C--S = 6.1 Ohms C--R = 1.2 Ohms S--R = 7.2 Ohms. The freezer temperatures are: Settings Temp A (left, 10 O'Clock) 14F B (middle, 12 O'Clock) -2.7F (recommended setting) C (rigfht, 2 O'Clock) -17.4F My fridge is working fine currently. Based on your teaching, my compressor is bad because the C--R value is way below 3 Ohms than the C--S value or 5X lower?
Hi, I live on a river boat in uk and run a small mains powered undercounter fridge freezer via an inverter, as you can imagine it pulls my battery bank down quite a bit and I have to charge them regularly every day, my question is , is it possible to convert the Compressor unit to run on 12v? Thanks
Cool...now what color wires go to each terminal? I have a guy who installed a different compressor and the pins from the old unit to the new unit are swapped. The original compressor had the single pin at the top the "new to me" compressor has the single pin at the bottom. It appears to be that the red wire goes to the overload protector that goes onto the lone pin. then I'm left with a pink and light blue wire , that goes to the relay....what color wire goes to Start and/or what color wire goes to Run?
I have a question? Can I run a kitchen refrigerator on a home hi tech touchscreen Alexa thermostat (you see where I’m going with this 😂😁) and how do I do it? I’m thinking a remote wire straight from the home thermostat to the compressor 🤷🏽, or would I run it to the control panel/board and where do i enter/input ( I would rather bypass the panel, but leave it connected so I can run the compressor straight off the thermostat if possible) ?
Is it ok to use 1/5hp compressor to replace the old one with 1/4hp (310L chest freezer)? Coz after replacement, still not freezing enough. I was told that the new compressor model (1/5hp) is equivalent to the old one (1/4hp).
You said, the run terminal is neutral and Start is joint with Run wire, but disconnect when the compressor takes soft start, My question is, what will happen if it didn't disconnect?
Diret starinv point power givd phasd one point ..rpointond powed givd same oint line startinv poing giveing conacting capciter ouf po dischargd c comon poing n.. netusl lind give saterdiret capciyef usinv satartinv pointef ok damgex comprssor replcinv firsg setup g selfy and disconnetinv and gas removeing old comprssof after line cuting or welding and remove sng methad ok renoveinv out tacking ok
Seem - not Seam Seam = Joint consisting of a line formed by joining two pieces Seem = Appears to be like ---- Read more to improve your knowledge of the English language
Yes, My R12 Freezer Compressor after 28.6 years of great services? But I have to replace it with an R12 or R600A Compressor, both are hard to find the BTU & LRA need to match! Oh don't forget the Oil! 4 difference only the MO work in the old Freezer 21 cu-ft upright or chest! Manual Defrost Have I known it bad? Trip the breaker!
I wish to know how may I switch a 220vac compressor into 12vac. How to rewind it, what wire gauge to use, etc. I wand to operate my refreg on battery without using an inverter. Is it possible?
Hi Sir, I tested the compressor accordance with your guide but the result look different M-->C=8.8 S--->C=8.8 S--->M=9 do you know why i get this value at my compressor please. Thanks in advance
@@forevertechenglish im sorry i just watch few more things about compressor..the read like that its because my compressor is inverter compressor the read will be all same..
Great Video...Unfortunately the (translated english) narration makes a "dog's breakfast" out of it... which is a bit sad.. Possibly this can be mitigated as AI translation is getting better and better, best regards)
Manufacturers unfortunately use any color they choose for that dat. Ther is NO Standard- And theU.S. is particularly recalcitrant and refuses to follow Worl/EU standard for wiring color. And North Americans are so brainwashed and ignorant 0= that they cannot count to 10 without using their fingers - BRAINWASHED TO USE IMPERIAL MEASUREMENTS -- Only the people can FORCE change 0- but they are too dumb and too brainwashed. The USA committed to the metric system in 1875 by signing an international agreement. 'LA CONFÉRENCE DI MÉTRE' in Paris [FRANCE] Signed by M. Ashbourne the U.S. Envoy to France All its units have been defined to the metric standard since then in the USA for Trade and Commerce. Search for 'THE CODE OF LAWS OF THE UNITED STATES OF AMERICA' §205b clause (1) states: To designate the metric system of measurement as the preferred system of weights and measures for the United States Trade and Commerce. Since 1994 both Metric and US customary units have been required to be shown on labels and packaging.
Sir I have one issue sir In samsung front load diamond model it run fine when without load if I make some load wash circulation it be very low rotate example whithout load it rotate 35 sec right and left. But with load it rotate only 6 sec remining time it wil ideal only I change carbon and tacho also but no use voltage are properly I get .what is the reson sir pls give any idea
Aslom go sloved bai frige not gas tomuch bai jumping removeing alone jobe othegues helping stroey much good good rparing slove gmind usfull and gas systom working no totaly wring parts and capcter rely compant using time bred all chenking not as wer stared mind lockel us somanney unit fee not all out cretive righting ex come all out in afte new systom big eng $$s dicideing not eascy jobe tock but out side jobe mind usfull all
That thing about compressors pin order is not a full true, for sure the start and run pins not always are located as you are saying in your video. Proof of that is for example de LG compresor model ND52LACH 115V/60hZ motor type CSR. In this case the commn pin wich you name as ( C ) is at the bottom but the Start Pin ( S ) is located at the top left and the Run pin ( R ) is located at the top right. So if yo conect that compresor according to your instructions, for sure you will blowup de compressor.
Further In the video, I have also told, how to check the compressor terminals by checking the resistance. One can identify the terminals through the resistance values too.
A helpful tip is to add 50ml of sulphuric acid to the compressor before regassing. This makes it unnecessary to flush or vacuum. The acid keeps the compressor clean.
The R winding can be described as WEAK - and that means it has SHORTED TURNS. Thus the compressor requires replacement. This often happens as a result of overheating - and often as sporadic winding failure -- It happens in Transformers also - It's just the way it is REPLACE THE COMPRESSOR
I just can't trust the videos where they won't show their face and they use the canned fake voice. If they knew what they were doing they wouldn't work so hard at being anonymous, would they?
Thank you for this easy to follow instructional video on how to test/check a refrigerator compressor. You helped me to understand how to see if a compressor is still good or needs to be replaced. Thank you again and keep up the great content.
Thank you so much for sharing this information you've taught me something about the compressor on the mini fridge I just got from a friend. They said it wasn't working and that they have fixed it. However at 5 it's not getting cold enough and the refrigerator seems to be getting hot so I thought to take a look at the compressor and look on UA-cam to see what was said about this refrigerator. The compressor has the three pins on the side not on the top it is protected by a box. It looks as though the wires have been chewed by something and it looks like I will soon be rewiring this compressor when I have the money. Hopefully this fixes my problem and I don't have to replace the whole compressor. For now working it just doesn't get very cold. At least I know it's a problem in the wiring back here. I wish I could take a picture to show you or send you some video.😂 I am worried because this compressor is very hot and so was the sides of the fridge. It looks like I'll be doing some work on this one. Thank you so much for being there.
You can send me its photos and videos on facebook page or instagram page
I have surfed the net and find this video very helpful to determine the weak compressor. It is very informative. Thanks for uploading. Subscribed.
Us gas ok
R13r us usinv gas cgafgd and solved ok
I am just starting to learn about refrigeration.
And your videos are amazingly useful.
Thank you for sharing.
Good vibes for you from México...🇲🇽
Thanks and welcome
Comerssar is 3terminal refaget....rs ru
Ruing starting comeing point starting is power giveing ruing is one phase and netarl giveing systomes ruing ...
Very good tutorial, I learn this video. Thank you. Full support from Philippines. God bless.
Stay connected
brilliant.. the winding diagram very helpful and you explain it very well
Many thanks!
AWESOME! Thanks for teaching this. Thanks. I have subscribed for this video alone.
Very nicely clarified the pins of a compresser
Helpful video forever I have seen experienced tutor thank you alot
Glad it helped
Very good video, well explained and understandable, thank you!
Glad it was helpful!
Saved my life and my fridge.Thanks
Glad I could help!
thank you for sharing this video sir👍👍
Thanks for video❤❤ iamfram zahdan iran
Very useful, thanks 🙏!
Good morning
Thank you in advance for the video. Individual things are explained nicely.
Unfortunately, I can't understand some of it. Can I ask for an explanation (description from 4 minutes 19 seconds) of the entry on the left: C=R+S, R=Medium, S=Low.
What measured values does this apply to (resistance, voltage). The description on the right side C+S=15.3 Ohm, C+R=16 Ohm, S+R=32 Ohm is super explained and clear. I just can't understand the description on the left.
Regards
Thanks 👍 for this helpful video
Happy to help
After connecting any refrigerator compressor before switching on
Use a clamp on (amp) meter
To check the start
The amp reading will be higher
To check the run
The amp reading will be less then starting
It is great information. Thanks indeed.
The freezer compartment works fine, but the fridge compartment does not cool at all.
So I tested the compressor in accordance with your informative guide.
M-->C=17
S--->C=30
S--->M=48
I guess this means it's time to stick a pipe through the top and use the fridge as a wardrobe.
I don't understood the values you wrote, can you elobrate further.
@@forevertechenglish
There are no markings to identify the three prongs on my compressor, but the relay that plugs into the compressor is marked C, S, & M at the corresponding points. I'm assuming M is the same as R. If I were to rewrite this using your terminology:
C + S= 30 ohms
C + R =17 ohms
S + R = 48 ohms
Between C + S and C + R is a 13 ohm difference. That's bad, right?
Your Compressor has gone bad according to the reading you mentioned
@@forevertechenglish Yes. It makes a high pitch squeal when starting up, too, so your video helped confirm my suspicion.
When the FREEZER {compartment} is working as it should
T%he compressor is functioning normally
Some Eastern EU refrigerators were more advanced than
those in the Greedy CORPORATE West - and were built with
two compressors -
one for the FREEZER - and
one for the REFRIGERATOR section.
I had one decades ago - and it was built in Yugoslavia -
when the USSR existed
That refrigerator.Freezer was designed and built to last -
unlike appliances and devices today - built to last 4 years max ---
And manufacturers only keep replacement parts for 5 years ---
then they dump them - SO the consumer is unable to buy replacement parts
- and is FORCED to spend their income on expensive NEW Junk.
That is economic slavery.
Very good 🕉️🚩🇮🇳🙏
Running to common is thick gauge winding than starting winding gauge so comon to running winding ohms is less than starting winding
I’ve been doing refrigeration repairs for 47 years and I never heard of a weak winding. There either open winding. Shorted winding.( internally. ). or shorted to ground. and I call that a multimeter.
The weak winding means that the compressor starts fine and runs fine at the start, but 10-15 minutes later, the compressor heats up more than usual; sometimes, there can be electrical causes the compressor to heat up, but if the electricity is ok, the compressor still becomes so hot that it even trips the protecting thermostat, which stops the compressor. In the area where I am working, the people do not believe you when the compressor starts well and works for a few minutes. At that moment, we used the word "weak" to make them understand that the compressor is faulty.
I replaced my relay and overload and my refrigerator started working again but after a few hours it stopped working again any suggestions
High amper comeping not coot what resong
@ could not understand a word you wrote what language is that?
Many many thanks to you
Good vedio respectfully❤❤❤👍🙏👌👌
Stay connected
Awesome educational video. Thank you for sharing.
I had a Magic Chef (no short to ground, in ohms) with
C & S = 12.1,
C & R = 10.2,
S & R = 17.4. What might have happened to S & R?
Also, I believe you mentioned that adding a capacitor to the start or run winding if anyone of them happened to get weak. Do you have another video showing how to determine the proper uf to add and the wiring connection? Regards.
Very cool!
The windings of the compressor on my Whirlpool Fridge (1999 model) are as follows:
C--S = 6.1 Ohms
C--R = 1.2 Ohms
S--R = 7.2 Ohms.
The freezer temperatures are:
Settings Temp
A (left, 10 O'Clock) 14F
B (middle, 12 O'Clock) -2.7F (recommended setting)
C (rigfht, 2 O'Clock) -17.4F
My fridge is working fine currently.
Based on your teaching, my compressor is bad because the C--R value is way below 3 Ohms than the C--S value or 5X lower?
My fridge is working fine currently'' you capacitor is working fine now. when it goes the rest will go with it
Very clear explanation my friend, thanks
You are welcome!
Hi, I live on a river boat in uk and run a small mains powered undercounter fridge freezer via an inverter, as you can imagine it pulls my battery bank down quite a bit and I have to charge them regularly every day, my question is , is it possible to convert the Compressor unit to run on 12v? Thanks
De teaching is superb🤞
Glad to hear that
Thank you sir new subscriber
Welcome aboard!
Very important information
Glad you think so!
Thank you dear sir.
Most welcome
Thank you!
❤️❤️
Cool...now what color wires go to each terminal?
I have a guy who installed a different compressor and the pins from the old unit to the new unit are swapped. The original compressor had the single pin at the top the "new to me" compressor has the single pin at the bottom.
It appears to be that the red wire goes to the overload protector that goes onto the lone pin.
then I'm left with a pink and light blue wire , that goes to the relay....what color wire goes to Start and/or what color wire goes to Run?
I have a question?
Can I run a kitchen refrigerator on a home hi tech touchscreen Alexa thermostat (you see where I’m going with this 😂😁) and how do I do it? I’m thinking a remote wire straight from the home thermostat to the compressor 🤷🏽, or would I run it to the control panel/board and where do i enter/input ( I would rather bypass the panel, but leave it connected so I can run the compressor straight off the thermostat if possible) ?
Its nice video content help alot
Glad it helped
very good job its really interested
Thanks mate
i learn alot tnx
Pleasure
Is it ok to use 1/5hp compressor to replace the old one with 1/4hp (310L chest freezer)? Coz after replacement, still not freezing enough. I was told that the new compressor model (1/5hp) is equivalent to the old one (1/4hp).
Thank yu for the detailed work but l wish to confirm if the live is called common because from other videos they refer to neutral as common
Live is called common, The run terminal is neutral and start is joint with run wire, but disconnects when the compressor takes soft start.
You said, the run terminal is neutral and Start is joint with Run wire, but disconnect when the compressor takes soft start,
My question is, what will happen if it didn't disconnect?
I have exactly the same problem with the first compressor you have shown. Which capacitor can i put and where please? Ha e you any diagram?
too good helpful
Us u lap
Very good ❤
If we want connect running capacitor with the first one compressor..quide me the value of running capacitor. Thanks
Dont make something easy with difficult theory. That is simple work.
Comprsdor wiring pointex 230v ok teminal ok 3point ruing starting ok c comon point runing ok
Diret starinv point power givd phasd one point ..rpointond powed givd same oint line startinv poing giveing conacting capciter ouf po dischargd c comon poing n.. netusl lind give saterdiret capciyef usinv satartinv pointef ok damgex comprssor replcinv firsg setup g selfy and disconnetinv and gas removeing old comprssof after line cuting or welding and remove sng methad ok renoveinv out tacking ok
All of the refrigerator compressors I have checked have 4Ω and 6Ω readings. These are 1/3hp compressors.
Excellent
Thank you so much 😀
Güzel bilgiler için teşekkür ederim
Geri bildirim için teşekkürler canım
I add up everything like u did in the video c+s and c+r but when I add s+r the values dont match what does that mean.
When S+R don't match it means the compressor winding is bad.
What does it mean if the readings are near zero ohms on all three pins?
it means the compressor is dead...
Good job brother. You seam every where. HNWYS
Seem - not Seam
Seam = Joint consisting of a line formed by joining two pieces
Seem = Appears to be like ----
Read more to improve your knowledge of the English language
Oh dear make more videos from like this electricity
Excellent dimo
Thanks
Thank you sir
Have a nice day,,can we replace an ac compressor not same model ,,but sama LRA or the same Horse power..
Thank you sir
Welcome
Please, i need help here.
C+S is 19 ohms
C+R is 13 ohms
S+R is 32 ohms.
Is this compressor still good?
Please, it's urgent i get a response.. thanks
Dobry film,mam pytanie jak uruchomić sprężarkę na krótko inwentorową ?
Zrobiłem o tym film, oto link do filmu. ua-cam.com/video/GHMEl6YQV8U/v-deo.html
Yes, My R12 Freezer Compressor after 28.6 years of great services? But I have to replace it with an R12 or R600A Compressor, both are hard to find the BTU & LRA need to match! Oh don't forget the Oil! 4 difference only the MO work in the old Freezer 21 cu-ft upright or chest! Manual Defrost Have I known it bad? Trip the breaker!
Yes I try it with rco410 buzz & do nothing, rco210 it clicks, and trip the breaker
Thanks
I wish to know how may I switch a 220vac compressor into 12vac. How to rewind it, what wire gauge to use, etc. I wand to operate my refreg on battery without using an inverter. Is it possible?
NO
The common- starting is higher reading than common-running.
Okay!!
Would like to fit a danfoss compressor in a 12 volt everchill 11 cu ft, is it possible
Check the specification of the old compressor, means what is its size in its datasheet
B = C
W = S
R = R
Black is common
For some reason when I am addressed as “friend” by someone whom I’ve never met I always think of the term “comrade”.
Hi Sir, I tested the compressor accordance with your guide but the result look different
M-->C=8.8
S--->C=8.8
S--->M=9
do you know why i get this value at my compressor please. Thanks in advance
Your Compressor Is BAd
@@forevertechenglish im sorry i just watch few more things about compressor..the read like that its because my compressor is inverter compressor the read will be all same..
I am not looking for resister resistance. I am looking for relay connection on a compressor
Thank you
You're welcome
Super
So nice
what size capacitor can
i use for this
Great
Hey what is the video called where you connect the capacitor
I didn't made a video on where I have connected a capacitor with a compressor.
Good
Thanks
Great Video...Unfortunately the (translated english) narration makes a "dog's breakfast" out of it... which is a bit sad..
Possibly this can be mitigated as AI translation is getting better and better, best regards)
Imsary my language very bad ❤ tank you very much for helping
So what color is the common wire. I have a white one and a red one. Located in the US.
Manufacturers unfortunately use any color they choose for that dat.
Ther is NO Standard-
And theU.S. is particularly recalcitrant and refuses to follow Worl/EU standard for wiring color.
And North Americans are so brainwashed and ignorant 0= that they cannot count to 10 without
using their fingers - BRAINWASHED TO USE IMPERIAL MEASUREMENTS --
Only the people can FORCE change 0- but they are too dumb and too brainwashed.
The USA committed to the metric system in 1875 by signing an international agreement.
'LA CONFÉRENCE DI MÉTRE' in Paris [FRANCE]
Signed by M. Ashbourne the U.S. Envoy to France
All its units have been defined to the metric standard since then in the
USA for Trade and Commerce.
Search for 'THE CODE OF LAWS OF THE UNITED STATES OF AMERICA'
§205b clause (1) states:
To designate the metric system of measurement as the preferred system
of weights and measures for the United States Trade and Commerce.
Since 1994 both Metric and US customary units have been required to be
shown on labels and packaging.
❤
❤
What is function of run capacitor in refrigerator please?
Sir I have one issue sir
In samsung front load diamond model it run fine when without load if I make some load wash circulation it be very low rotate example whithout load it rotate 35 sec right and left. But with load it rotate only 6 sec remining time it wil ideal only I change carbon and tacho also but no use voltage are properly I get .what is the reson sir pls give any idea
Comprssar r power line phase starting point only second giveing power c comon N.only.
@@jollyscaria1922 sry sir I can't understand pls give some more detailed information
Is the Pcb fine
Aslom go sloved bai frige not gas tomuch bai jumping removeing alone jobe othegues helping stroey much good good rparing slove gmind usfull and gas systom working no totaly wring parts and capcter rely compant using time bred all chenking not as wer stared mind lockel us somanney unit fee not all out cretive righting ex come all out in afte new systom big eng $$s dicideing not eascy jobe tock but out side jobe mind usfull all
Je suis nouvellement abonnés vous n'avez pas les vidéos en français svp
Can u put ctto?
Please i will need some compressor how can i get it
Where are you from?
That thing about compressors pin order is not a full true, for sure the start and run pins not always are located as you are saying in your video. Proof of that is for example de LG compresor model ND52LACH 115V/60hZ motor type CSR. In this case the commn pin wich you name as ( C ) is at the bottom but the Start Pin ( S ) is located at the top left and the Run pin ( R ) is located at the top right. So if yo conect that compresor according to your instructions, for sure you will blowup de compressor.
Further In the video, I have also told, how to check the compressor terminals by checking the resistance. One can identify the terminals through the resistance values too.
A helpful tip is to add 50ml of sulphuric acid to the compressor before regassing. This makes it unnecessary to flush or vacuum. The acid keeps the compressor clean.
Wdf r u out of ur mind this will destroy the internals of the compressor 😢😢
I get 15.5 on all combinations, why?
Ur compressor is dc this method is for ac compressor
C-S=34.4
C-R=8.8
S-R=43.3
What's your opinion??
Running winding too much weak.
The R winding can be described as WEAK -
and that means it has SHORTED TURNS.
Thus the compressor requires replacement.
This often happens as a result of overheating -
and often as sporadic winding failure --
It happens in Transformers also - It's just
the way it is
REPLACE THE COMPRESSOR
Where is the ground connections
Volt tim enter ?
Is that the voice of AI???
Yes
Ma perché non si traduce in italiano
I am sorry you explained to God but don't mention the capacitor connection why?
Will explain it in the next video.
يا اخي لطالما تحكي وتشرح بالانكليزي , ليش تكتب عنوان الفيديو بالعربي؟؟؟!!!
💤😴
PLEASE HELP.
I just can't trust the videos where they won't show their face and they use the canned fake voice. If they knew what they were doing they wouldn't work so hard at being anonymous, would they?
Well, this video is a dubbed version in english, the original is on another channel with a different language.
You ripped this video from someone 😂
nope at all, its my own creation, Just translated into english.
!
33
If you're going to call your channel "Forever Tech English", you should probably learn English.
Well, these are old video's which I my self feels have some mistakes grammatically. Well trying to improve day by day.
Practice makes a man or either you can say the person better.
Non si capisce un tubo